Axiom DEX User manual

QUICK START GUIDE
DEX BACKREST HARDWARE

• 10mm wrench
Tool Needed:
Fastener Key:
Assemblies Included:
Two sets of
fasteners provided.
Reference Fastener
Key below.
X2
• tape measure or level• 5mm Allen wrench
X2

DEF
.
1” - 2”
A
B
C
C
D
Pivot
Hole A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
osi on P1/A1 P1/A2 P1/A3
si on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
t
i
t
i
20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
2 7 1 2
1 6 1 5 1
2
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
C
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
A
B
*Use provided 3/8” spacer
and provided longer
fasteners when back width is
2” narrower than frame width.
A
BDE
F
.
1” - 2”
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
BC
0-2”
Pivot
Hole
Angle
Adjustment
Holes
A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
Front Posi on P1/A1 P1/A2 P1/A3
Rear Posi on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
t
i
t
i
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
1”
A
BC
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A xi o m
B ack
W i d t h
Inner Slo t s Out er Slo t s
1
2" (30.5cm) 11" (28.0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -40.5cm)
16" (40.5cm) 14" -15" (35.5cm -38.0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm - 43.0cm) 18" - 20" (45.5cm - 50.5cm)
20" (51.0cm) 18" -19" (46.0cm -48.5cm) 20" -22" (50.5cm -55.5cm)
22" (56.0cm) 20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
FitsBack Frame Widths
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
configurations.
Pivot
Bracket A rro w
Bracket A rro w
2
1
2
1
Front Position
(Farther forward from back canes)
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
Rear Position
(Closer to back canes)
Pivot
5Install backrest clamp assembly to the backrest bracket
with two screws (A) and two washers (B) using a 5mm
Allen wrench. Note: The angle is set by installing the
hardware in the holes determined in Step 4.
Loosely assemble the clamps onto the back canes at
desired location. Symmetrically adjust the back plates
along the slots to adjust height and then adjust the
depth and angle if needed. Ensure both sides are installed
at the same height, depth and angle settings.
6
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
B
*Use provided 3/8” spacer
and provided longer
fasteners when back width is
2” narrower than frame width.
General Setup (Before Delivery)
14
Determine installation slots based on configuration.
A
B
B
C
DEF
6
.
1” - 2”
No interference at
clamp locations
No interference at
clamp locations
5
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
B
C
C
D
1” - 2”
A xi o m
Back
W i d t h
Inner S lo t s Out er S lo t s
12" (30.5cm) 11" (28.0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -40.5cm)
16" (40.5cm) 14" -15" (35.5cm -38.0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm - 43.0cm) 18" - 20" (4 5.5cm - 50.5cm)
20" (51.0cm) 18" -19" (46.0cm -48.5cm) 20" -22" (50.5cm -55.5cm)
22" (56.0cm) 20" -21" (51.0cm -53 .5cm) 22" -24" (56.0cm -61.0cm)
Fits Back Frame Widths
Remove backrest shell from cover. Install backrest bracket
to shell with stud plate (A), two washers (B) and two dome
nuts (C). Install so stud plates are 1” from the top of each
bracket slot. Loosely tighten hardware. Repeat on opposite
side ensuring both sides are set in the same Alignment Guide
position.
1”
A
BC
1
” -
2
”
c
e at
t
ions
No
cla
m
1” - 2”
Determine the clamp fasteners needed by referencing the
Fastener Key on the back of this document.
Loosely assemble the clamps onto the back canes at the
desired location talked about in step 3. Bolts should thread
inwards from the outside of the chair. Tighten clamp enough
so it stays in place and repeat on opposite side.
Use a level and a tape measure to ensure the clamps are
level and the distance from backcane to clamp mount is 1/2”.
1/2”
7
Identical Alignment Guide Positions
8
Adjust the depth and angle by moving the backrest assembly
to the desired positions. With position determined, ensure
the bolts are secured in the same scallop on the bracket on
both sides of the chair.
Hold the backrest shell against the chair at approximate height
desired. Find a back cane location that can accomodate the
clamp near the center of the slots on the backrest bracket.
Typically the backrest will rest 1-2” above the cushion.
Ensure same
scallop is used
on both sides of
chair
Perform Check, see Check Section in next section.
Inner Slot
Outer Slot
Install backrest assembly onto the clamp mounts. Ensure
both backrest plates are set in the same Alignment Guide
position. Adjust the back height by moving the backrest
along the plate up or down to desired height.
Perform Check, see Check Section in next section.
2
37
.
C
D
Pivot
Hole A3
P1
A6
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B)
and two nuts (C). Stud plates should be 1.5 - 2” from
the top of the slot. Loosely tighten hardware. Repeat
on opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if the configuration requires.
Hold the backrest shell against the chair at approximate
height desired. Find a back cane location that can a
ccomodate the clamp near the center of the slots on
the backrest bracket. Typically the backrest will rest
1-2” above the cushion.
A
BDEF
1
General Setup (Before Delivery)
2
.
1” - 2”
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
BC
0-2”
Pivot
Hole
Angle
Adjustment
Holes
A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
Front Posi on P1/A1 P1/A2 P1/A3
Rear Posi on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
t
i
t
i
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
1”
A
BC
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
Determine installation slots based on configuration.
A x io m
B ack
W i d t h
Inner Slo t s Out er S lo t s
12" (30.5cm) 11" (28 .0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -4 0.5cm)
16" (40.5cm) 14" -15" (35.5cm -38 .0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm- 4 3.0cm) 18" - 20" (45.5cm - 50.5cm)
20" (51.0cm) 18" -19" (4 6.0cm -48.5cm) 20 " -22" (50.5cm -55.5cm)
22" (56 .0cm) 20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
Fits Back Frame Widths
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
Pivot A ngle 3 P ivo t A ngle 2 P ivo t Angle 1
4
2
-0° -2.5° -5°
Bracket A rrow
Bracket A rrow
2 7
5
2 1
1
+0° +2.5° +5°
1 6
2 7
1
1 2 3
3
1 6 1 5 1 4
2
Front Position
(Farther forward from back canes)
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
Rear Position
(Closer to back canes)
Pivot A ngle 3 P ivot A ngle 2 P ivo t A ngle 1
C
Loosely assemble the clamps onto the back canes at
desired location. Symmetrically adjust the back plates
along the slots to adjust height and then adjust the
depth and angle if needed. Ensure both sides are installed
at the same height, depth and angle settings.
6
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
A
B
*Use provided 3/8” spacer
and provided longer
fasteners when back width is
2” narrower than frame width.
Choose the desired angle and depth set up. Use the
images and charts below to help determine how to
achieve desired configurations.
5
Install backrest clamp assembly to the backrest bracket
with two screws (A) and two washers (B) using a 5mm
Allen wrench. Note: The angle is set by installing the
hardware in the holes determined in Step 4.
6
Adjust the depth and angle by moving the backrest
assembly to the desired positions. With position
determined, ensure the bolts are secured in the same
scallop on the bracket on both sides of the chair.
Perform Check, see Check Section in next section.
Loosely install the back mount cover with one screw
using a 5mm Allen wrench and repeat on opposite side.

Fitting Adjustments (User Present)
WARNING: IT MAY BE POSSIBLE TO ADJUST THE FINAL POSITION OF THE AXIOM BACK WITH AN END USER
SEATED IN HIS WHEELCHAIR. THIS REQUIRES THAT THE END USER BE ABLE TO SIT IN A STABLE POSITION
WITHOUT THE USE OF THE BACKREST. IT MAY ALSO BE POSSIBLE IF THERE ARE PEOPLE WHO CAN
SUPPORT THE END USER DURING ADJUSTMENT. THIS SHOULD BE VERIFIED BY A CLINICIAN TRAINED TO
MAKE THAT DETERMINATION. ALWAYS MAKE SURE THE WHEELCHAIR WHEEL LOCKS AND ANTI-TIPS ARE
SET AND LOCKED. IF THESE CONDITIONS CANNOT BE MET, THE END USER SHOULD TRANSFER FROM THE
WHEELCHAIR BEFORE MAKING ADJUSTMENTS. FAILURE TO TAKE THESE PRECAUTIONS MAY RESULT IN A
FALL AND THE POTENTIAL FOR A SERIOUS INJURY.
12
If you have any questions or concerns about any
aspect of this Axiom back, please do not hesitate to
contact us by:
Telephone:
715-254-0991
In Writing at:
Ki Mobility
5201 Woodward Drive
Stevens Point, WI 54481
U.S.A
Or via email at:
[e-mail]
Ki Mobility
5201 Woodward Drive
Stevens Point, Wisconsin 54481
715-254-0991
www.kimobility.com DCN1071.1
RESULT IN A FALL AND THE POTENTIAL FOR A SERIOUS INJURY.
To adjust the angle and depth of the backrest, loosen
the pivot screw on the backrest bracket and remove
the angle adjustment screw. Grab and move/tilt the
backrest assembly to desired position. Align holes for
desired backrest angle and reinstall the angle adjustment
screw. Retighten the pivot screw. Use the images and
charts in General Setup Step 4 to identify screws and
figure out the angle configurations.
0° 2.5 5°
Front Posi on P1/A1 P1/ P1/A3
t
i
t
i
A
Remove the back mount cover. Loosen the backrest bracket
hardware (A) to move the entire back assembly up or down in
the slots to desired height. If more adjustability is needed, the
hardware can be removed and reinstalled so both studs are in
the same stud slot. Ensure both sides are set in the identical
height configuration.
3
Install the back mount cover with one screw using a 5mm Allen wrench and repeat on opposite side. See General Setup Step
7 for imagery if needed.
a. Tighten all fasteners completely and assure that the hardware does not move out of the adjusted position
under the load of the user.
Perform Check -

GUÍA DE INICIO RÁPIDO
HARDWARE DEL RESPALDO FXT

• Llave inglesa de 10mm
Herramiento necesaria:
Fastener Key:
Elementos incluídos:
X2
• Cinta métrica o nivelador• Llave octogonal de 5mm
X2

DEF
.
1” - 2”
A
B
C
C
D
Pivot
Hole A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
osi on P1/A1 P1/A2 P1/A3
osi on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
t
i
t
i
20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
2 7 1 2
1 6 1 5 1
2
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
C
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
A
B
*Usar el distanciador de
3/8” incluido, y los fijadores
más largos también incluídos
cuando el ancho del espaldar es
2” menor que el ancho de la estructura.
A
BDE
F
.
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
BC
0-2”
Pivot
Hole
Angle
Adjustment
Holes
A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
Front Posi on P1/A1 P1/A2 P1/A3
Rear Posi on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
4
t
i
t
i
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
1”
A
BC
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
Determine installation slots based on configuration.
A xi o m
B ack
W i d t h
Inner Slo t s Out er Slo t s
1
2" (30.5cm) 11" (28.0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -40.5cm)
16" (40.5cm) 14" -15" (35.5cm -38.0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm - 43.0cm) 18" - 20" (45.5cm - 50.5cm)
20" (51.0cm) 18" -19" (46.0cm -48.5cm) 20" -22" (50.5cm -55.5cm)
22" (56.0cm) 20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
FitsBack Frame Widths
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
Choose the desired angle and depth set up. Use the images
and charts below to help determine how to achieve desired
configurations.
Pivot
Bracket A rro w
Bracket A rro w
2
1
2
1
Front Position
(Farther forward from back canes)
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
Rear Position
(Closer to back canes)
Pivot
5Install backrest clamp assembly to the backrest bracket
with two screws (A) and two washers (B) using a 5mm
Allen wrench. Note: The angle is set by installing the
hardware in the holes determined in Step 4.
Loosely assemble the clamps onto the back canes at
desired location. Symmetrically adjust the back plates
along the slots to adjust height and then adjust the
depth and angle if needed. Ensure both sides are installed
at the same height, depth and angle settings.
6
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
B
*Use provided 3/8” spacer
and provided longer
fasteners when back width is
2” narrower than frame width.
Configuración general (previa a la entrega)
14
Determinar las ranuras de instalación en base a la
configuración.
A
B
B
C
DEF
6
.
1” - 2”
No interference at
clamp locations
No interference at
clamp locations
5
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
B
C
C
D
1” - 2”
Ancho de
espaldar
Axiom
Ranuras internas Ranuras externas
12" (30.5cm) 11" (28.0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -40.5cm)
16" (40.5cm) 14" -15" (35.5cm -38.0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm - 43.0cm) 18" - 20" (4 5.5cm - 50.5cm)
20" (51.0cm) 18" -19" (46.0cm -48.5cm) 20" -22" (50.5cm -55.5cm)
22" (56.0cm) 20" -21" (51.0cm -53 .5cm) 22" -24" (56.0cm -61.0cm)
Remove backrest shell from cover. Install backrest bracket
to shell with stud plate (A), two washers (B) and two dome
nuts (C). Install so stud plates are 1” from the top of each
bracket slot. Loosely tighten hardware. Repeat on opposite
side ensuring both sides are set in the same Alignment Guide
position.
1”
A
BC
1
” -
2
”
c
e at
t
ions
No
cla
m
1” - 2”
Determine the clamp fasteners needed by referencing the
Fastener Key on the back of this document.
Loosely assemble the clamps onto the back canes at the
desired location talked about in step 3. Bolts should thread
inwards from the outside of the chair. Tighten clamp enough
so it stays in place and repeat on opposite side.
Use a level and a tape measure to ensure the clamps are
level and the distance from backcane to clamp mount is 1/2”.
1/2”
7
Identical Alignment Guide Positions
8
Adjust the depth and angle by moving the backrest assembly
to the desired positions. With position determined, ensure
the bolts are secured in the same scallop on the bracket on
both sides of the chair.
Hold the backrest shell against the chair at approximate height
desired. Find a back cane location that can accomodate the
clamp near the center of the slots on the backrest bracket.
Typically the backrest will rest 1-2” above the cushion.
Ensure same
scallop is used
on both sides of
chair
Perform Check, see Check Section in next section.
Inner Slot
Outer Slot
Install backrest assembly onto the clamp mounts. Ensure
both backrest plates are set in the same Alignment Guide
position. Adjust the back height by moving the backrest
along the plate up or down to desired height.
2
7
.
C
D
Pivot
Hole A3
P1
A6
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Ranuras internas
Ranuras externas
A
BDEF
1
General Setup (Before Delivery)
2
.
1” - 2”
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
A
B
C
C
D
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
BC
0-2”
Pivot
Hole
Angle
Adjustment
Holes
A3
A1
A4
P2/A2
A5
P1
A6
0° 2.5° 5°
Front Posi on P1/A1 P1/A2 P1/A3
Rear Posi on P2/A4 P2/A5 P2/A6
Pivot / Angle Hole
1” - 2”
t
i
t
i
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
1”
A
BC
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
A
1”
BC
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
1”
>0-2” Narrower than back - Assemble in Inner Slots
0-2” Wider than back - Assemble in Outer Slots
Any other size difference - Do not assemble
BC
A
Determine installation slots based on configuration.
A x io m
B ack
W i d t h
Inner Slo t s Out er S lo t s
12" (30.5cm) 11" (28 .0cm) 12" -14" (30.5cm -35.5cm)
14" (35.5cm) 12" -13" (30.5cm -33.0cm) 14" -16" (35.5cm -4 0.5cm)
16" (40.5cm) 14" -15" (35.5cm -38 .0cm) 16" -18" (40.5cm -45.5cm)
18" (45.5cm) 16" - 17" (40.5cm- 43.0cm) 18" - 2 0" (45.5cm - 50.5cm)
20" (51.0cm) 18" -19" (4 6.0cm -48.5cm) 20 " -22" (50.5cm -55.5cm)
22" (56 .0cm) 20" -21" (51.0cm -53.5cm) 22" -24" (56.0cm -61.0cm)
Fits Back Frame Widths
Remove backrest shell from cover. Install backrest
bracket to shell with stud plate (A), two washers (B) and
two nuts (C). Stud plates should be 1.5” - 2” from the
top of the slot. Loosely tighten hardware. Repeat on
opposite side. Note: For FXT Hardware only, the stud
plate can be installed so both studs are in the same slot
if configuration requires.
A
B
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
>0-2” Narro
w
0-2” Wider t
h
Any other si
z
B
A
A
B
C
Inner Slot
Outer Slot
1” - 2”
1” - 2”
Pivot P ivot P ivo t
4
2
-0° -2.5° -5°
Bracket A rrow
2 7
5
2 1
1
+0° +2.5° +5°
1 6
2 7
1
1 2 3
3
1 6 1 5 1 4
2
Front Position
(Farther forward from back canes)
Rear Position
(Closer to back canes)
Pivot P ivot P ivo t
C
Loosely assemble the clamps onto the back canes at
desired location. Symmetrically adjust the back plates
along the slots to adjust height and then adjust the
depth and angle if needed. Ensure both sides are installed
at the same height, depth and angle settings.
6
Perform Check, see Check Section in next section.
7Loosely install the back mount cover with one screw using
a 5mm Allen wrench and repeat on opposite side.
A
B
*Use provided 3/8” spacer
and provided longer
fasteners when back width is
2” narrower than frame width.
Elegir la configuración preferida de angulación y
profundidad. Valerse de las imágenes y esquemas a
continuación para determinar cómo lograrlo.
5
6
Perform Check, see Check Section in next section.
Se adecúa a anchos de estructura
del espaldar de:
3
Foro
pivot
Regulación
del ángulo 1
Regulación
del ángulo 3
Regulación
del
ángulo 3
Flecha del soporter
Posición posterior (más cerca
de los tubos del espaldar)
Posición anterior (más lejos
de los tubos del espaldar)
Flecha del soporter
Posición posterior (más cerca
de los tubos del espaldar)
Posición anterior (más lejos
de los tubos del espaldar)
Ángulo 3
Ángulo 3
Ángulo 2
Ángulo 2
Ángulo 1
Ángulo 1
Quitar la carcasa del respaldo de su revestimiento.
Instalar el soporte del respaldo en la carcasa mediante
la placa de fijación perforada (A), dos arandelas (B) y
dos tuercas cerradas (C). Las placas de fijación
perforadas deben quedar a 1,5”-2” de la parte superior
de la ranura. Ajustar levemente el hardware y repetir en
el otro lado. Nota: sólo para el hardware de FXT, la placa
de fijación perforada puede instalarse de tal manera que
ambas placas estén en la misma ranura si así lo requiere
la configuración.
Sostener la carcasa del respaldo contra la silla de
ruedas a la altura deseada, aproximadamente.
Localizar una posición en el tubo del espaldar
donde pueda caber la abrazadera cerca del centro
de las ranuras en el soporte del respaldo. Normalmente
el respaldo se reposará a 1-2” sobre el cojín.
Instalar el conjunto de la abrazadera del respaldo en el
soporte del mismo mediante dos tornillos (A) y dos
arandelas (B) empleando una llave octogonal de 5mm.
Nota: el ángulo se fija instalando el hardware en los foros
determinados en el paso 4.
Ensamblar sin excesiva presión las abrazaderas sobre los
tubos del espaldar en la ubicación deseada. Simétricamente
ubicar las placas del espaldar a lo largo de las ranuras para
determinar la altura, luego de lo cual regular la profundidad y
la angulación si necesario. Cerciorarse que ambos lados
estén instalados con igual altura, profundidad y angulación.
Instalar sin excesiva presión el revestimiento de montaje del
espaldar con un tornillo empleando una llave octogonal de
5mm, y repetir en el otro lado.
Control, consulte la sección Check en la siguiente
sección.

12
DCN1071.1
RESULT IN A FALL AND THE POTENTIAL FOR A SERIOUS INJURY.
0° 2.5 5°
Front Posi on P1/A1 P1/ P1/A3
t
i
t
i
A
Quitar el revestimiento del montaje del espaldar. Aflojar el
hardware (A) del soporte del respaldo para desplazar todo
el conjunto del espaldar hacia arriba o hacia abajo en las
ranuras hasta la altura deseada. Si se necesita más capacidad
de regulación, el hardware puede quitarse y reinstalarse de tal
manera que ambas placas de fijación perforadas estén en la
misma ranura de la placa. Cerciorarse que ambos lados
tengan idéntica configuración de altura.
Regulación y configuración (con el usuario sentado)
Si tiene cualquier pregunta o inquietud sobre cualquier
aspecto del espaldar de la Axiom, no dude en ponerse
en contacto con nosotros:
Teléfono:
715-254-0991
Por escrito a:
Ki Mobility
5201 Woodward Drive
Stevens Point, WI 54481
U.S.A
O por correo electrónico en:
[e-mail]
Ki Mobility
5201 Woodward Drive
Stevens Point, Wisconsin 54481
715-254-0991
www.kimobility.com
ADVERTENCIA: ES POSIBLE REGULAR LA POSICIÓN FINAL DEL ESPALDAR AXIOM MIENTRAS EL USUARIO
ESTÁ SENTADO EN SUSILLA DE RUEDAS SÓLO SI PUEDE GUARDAR UNA POSICIÓN ESTABLE SIN APOYARSE
EN EL RESPALDO. ESTO TAMBIÉN SERÁ POSIBLE CON LA AYUDA DE PERSONAS QUE SOSTENGAN AL
USUARIO DURANTE LA REGULACIÓN. UN MÉDICO ESPECIALIZADO EN ESTOS CASOS PODRÁ DETERMI-
NARLO. VERIFICAR SIEMPRE QUE LOS SEGUROS DE LAS RUEDAS Y LOS ANTIVUELCO DE LA SILLA ESTÉN
ACTIVADOS Y FIRMES EN SU LUGAR - SI NO FUERA POSIBLE, EL USUARIO DEBERÁ TRANSFERIRSE DE LA
SILLA DE RUEDAS PARA PODER PROCEDER A LA REGULACIÓN. DEBE OBSERVARSE ESTA PRECAUCIÓN
PARA EVITAR CAÍDAS Y POTENCIALES DAÑOS GRAVES.
Para regular el ángulo y la profundidad del respaldo
aflojar el tornillo pivot del soporte del respaldo y luego
quitar el tornillo que regula el ángulo. Aferrar y desplazar
o reclinar el conjunto del respaldo hasta la posición
preferida. Alinear los foros para el ángulo necesario del
respaldo, luego volver a colocar el tornillo que regula el
ángulo. Volver a ajustar el tornillo pivot. Valerse de las
imágenes y esquemas del paso 4 - Configuración General
para identificar los tornillos y establecer las configuraciones
de ángulo.
a. Apretar firmemente todos los fijadores y verificar que el hardware no se mueva de la posición configurada
cuando se sienta el usuario.
Control -
Instalar el revestimiento del montaje del espaldar con un tornillo empleando una llave octogonal de 5mm, y repetir en el otro
lado. Ver el paso 7 - Configuración General si se necesitan imágenes.
3