displayit Flare User manual

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343 Flare v1.8 Updated 3/1/2016
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Assembly Instructions Page 1
Need Help?
Scan the QR code or go to
displayit.com/flare-guide
to watch an assembly video.
Foot Holes
Support Pole with
Push-Button Connector
Foot Holes
Diagram 1
46” SM
46” SM-PWR
46” SM 46” SM
46” SM
46” SM
46” SM-FT
46” SM-FT-AC
Power Transformer
Wire Pass-through Grommet
2. Assemble top and bottom of
frame using “I” shaped straight
connectors. Hand tighten wing
nuts to secure.
3. Assemble sides using “H”
shaped straight connectors.
Hand tighten wing nuts to secure.
4. Assemble perimeter of frame.
using corner connectors.
Do not tighten down wing nuts
until support poles are secure.
HorizontalHorizontal
Vertical
Vertical
Gap for
Lights
Gap for
Lights
Diagram 2
Bottom Half
of Support Pole
7. Attach top portion of support
poles support poles with
push-button connectors.
Lock upper latches to the top of
the frame.
5. Attach bottom half of support poles to bottom frame piece.
To attach support pole, pull the latch lever to unlock clasp.
Firmly push clasp into center channel of frame. Close latch
lever to secure. The frame should look like Diagram 2.
Note: Lever may not close all the way.
6. For single-sided displays, install the
support pole into the back channel of
the frame.
Note: For double-sided displays, make
sure to leave space for the light bars as
seen in Diagram 4 on the following page.
LockLock
Back Channel
for Single-Sided
Back Channel
for Single-Sided
Middle Channel
for Double-Sided
Middle Channel
for Double-Sided
UnlockUnlock
ClickClick
CAUTION:
METAL EDGES
MAY BE SHARP
1. Lay out frame pieces as seen in Diagram 1. Frame perimeter pieces are labeled with stickers
matching Diagram 1 to make this step easier. We recommend assembling the frame on its back.
Approximately 39” Apart
(Room for one short and one long light bar)

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343 Flare v1.8 Updated 3/1/2016
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Assembly Instructions Page 2
Diagram 3
8. Loosly attach top piece to side pieces using 2
corner brackets. Connect the support pole to the
center channel of the top piece. Hand tighten all
wing nuts on corner connectors to secure. At this
point, the frame should look like Diagram 3.
DO NOT EXCEED 9 LONG LED BARS PER 200 WATT POWER SUPPLY
(190 WATT MAX.) EVENLY DISTRIBUTE LIGHTS ACROSS BOTH OUTPUT WIRES
POWER SUPPLY MAY BECOME HOT WITH CONTINUED USE
UNPLUG AND ALLOW TO COOL BEFORE TOUCHING
9. Attach LED light bars to the frame using thumb screws and flat nuts as seen in Diagram 4.
Two short bars may be subsituted for one long bar.
Try to limit spaces between light bars, to create an even glow on the graphic.
For double-sided displays, the support pole may need to be moved to make room for the lights.
Thumb ScrewThumb Screw
Flat nut
Flat nut
10. Wire the lights as seen in
Diagram 4.
11. Snap-on wire management clips help stop wire shadows.
12. Feed the wires through the
flexible grommet. Plug the
transformer into an AC outlet
to test the lights.
Male Female
(Transformer Side)
(LED Side)
Bottom Lights: 2 Long, 3 Short LED Bars
Top Lights: 2 Long, 3 Short LED Bars
Wire clip
Wire clip
8’ Jumper Wire for Top Lights
Long LongShort Short Short
Long Long ShortShortShort
Approximately 39” Apar t
(Room for one short and one long light bar)

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343 Flare v1.8 Updated 3/1/2016
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Assembly Instructions Page 3
13. Attach feet using t-bolts and
wing nuts. Each t-bolt goes
through a counterbored hole in
the foot, then through a hole in
the metal frame. Secure with a
washer wing nut. Hand-tighten
until snug; do not over-tighten.
Counterbored holes
10 Foot (114”w x 92”h) Flare Frame Shown
14. Install graphics (See following
page for detailed instructions).
15. If hard fold lines are visible
in the fabric, smooth them out
with a steamer from the back
side of the graphic.
Fabric
Graphic
Silicone Welt
(On Back)

8’ (92” x 92”) Flare
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343 Flare v1.8 Updated 3/1/2016
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Assembly Instructions Page 4
Need Help?
Scan the QR code or go to
displayit.com/flare-guide
to watch an assembly video.
1. Using at least two people,
carefully stand the display up.
Starting in top-left corner, turn
and tuck graphic and silicone
into the channel. (#1 on diagram)
Use your fingertip (not fingernail)
for installation.
Note: For large frames, a step-ladder is
may be required for graphic installation.
2. Work across the top, tacking the graphic into the channel
every two to three feet. (#2 on diagram)
3. Tuck top, right corner into channel. (#3 on diagram)
4. Tuck remainder of top edge of graphic into top channel.
(#4 on diagram)
5. Inspect graphic for hard fold lines in the fabric. If desired,
smooth them out using a steamer from the back side of the
graphic.
6. Tuck bottom two corners. (#6 on diagram)
7. Tack middle of sides. (#7 on diagram)
8. Working from top to bottom, tuck remaining silicone in
on both sides. (#8 on diagram)
9. Tack middle of bottom. (#9 on diagram)
10. Tuck remaining bottom edge, working from outside to
inside. (#10 on diagram
11. Repeat installation steps for fabric on back of frame.
1 2 2 2 3
6 6
77
44
91010
88
Fabric
Graphic
Silicone Welt
(On Back)
Graphic Installation
Silicone
Silicone
Fabric
Fabric
Top of Frame
Caution! Installing silicone-edged graphics is techniqe sensitive; Practice will
shorten installation time. To watch a step-by-step assembly video, scan the QR
code to the right or go to displayit.com/flare-guide.
Handle graphics with care with clean hands in a clean environment.
Cloth or latex gloves recommended.
Keep graphics away from sharp objects.