displayit flare User manual

Flare Frame Required
For Support
Accessory Kiosk with Monitor Mount
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Updated 11/15/2019
Assembly Instructions Page 1
Parts List
Adjustable
Foot
Back Edge
ACCESSORY
KIOSK
SIDE
TOP
ACCESSORY
KIOSK
SIDE
BOTTOM
ACCESSORY
KIOSK
STANDARD
HORIZONTAL
ACCESSORY
KIOSK
MONITOR
HORIZONTAL
Large Panel x1
Shelf Bracket
with Knob Lock x2
Top Plate x1
Small Panel x2
Shelf x1
Thumb Knob x4*
Side Top Vertical x2
*Extra parts are provided
2.5” Screw and Washer x4*
Inline Splice x2 Thumb Nut x8*
Side Bottom Vertical x2 Standard Horizontal
with Knob Locks x3 Monitor Horizontal with Knob Locks x2
CableClips x4
Monitor Mount x1
M8 Knob x18*
(Includes 10 pre-installed in horizontals
and 2 pre-installed in shelf brackets)
M8 Threaded
Socket
M8 Knob Lock M8 Knob
Drill Holes
Lock
M8 Threaded
Sockets
M8 x 24mm
Thread
1/4-20 x 1”Thread
1/4-20 x 2.5”
Thread
Phillips Head
1/4-20 Thread
.5” x .7” Oval Head
32” x 11” Shelf
Parts are not shown to scale
M8 Knob
Rubber Pads
Lock

Accessory Kiosk with Monitor Mount
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Updated 11/15/2019
Assembly Instructions Page 2
4. Assemble the two sides to the
kiosk as seen above. The top and
bottoms attach together using an
inline splice and two M8 knobs.
6. Stand the kiosk up attach to the top
plate with two M8 knobs.
Note: The shelf (shown in green above)
makes a handy spacer between the
bottom of the kiosk and the Flare.
7. Adjust the bottom feet until the
Flare and kiosk are standing straight
(not leaning forwards or backwards). 8. Shelf brackets attach with thumb
knobs. Face the rubber pads upwards.
Set the shelf onto the brackets.
1. During Flare frame assembly, insert
two t-bolts into each channel of the top
horizontal. Continue building the Flare
frame per the Flare instructions. 3. Secure with four thumb nuts.
5A. Attach the horizontals to the left side as seen
above. The horizontals attach using knob locks
(See Knob Lock Instruction Details to the right.)
Note: The infill panels may be used as spacers.
5B. Slide the infill panels completely into the frame
and attach the right side.
5C. Attach the right side vertical to the horizontals. Ensure the “lock” teeth are
fully enaged and the
connection can’t wiggle.
ACCESSORY
KIOSK
SIDE
BOTTOM
ACCESSORY
KIOSK
SIDE
TOP
Inline
Splice
Adjustable
Foot
M8
Knobs
Threaded
Socket
Knobs Face
Backwards
Knob Lock Instruction Details
ACCESSORY
KIOSK
STANDARD
HORIZONTAL
ACCESSORY
KIOSK
STANDARD
HORIZONTAL
ACCESSORY
KIOSK
STANDARD
HORIZONTAL
ACCESSORY
KIOSK
MONITOR
HORIZONTAL
B Tighten knob clockwise
A. Insert lock into channel
Shelf used
as spacer
2. Place the kiosk top plate on top of
the flare with the four t-bolts passing
through the four holes

Accessory Kiosk with Monitor Mount
displayit.com 800.207.0311 After-Hours Emergency: Call or Text 678.723.5343
Updated 11/15/2019
Assembly Instructions Page 3
9. Insert four 2.5” long screws through
four washers, the monitor base plate, and
the two monitor mount horizontals.
10. Secure the monitor base plate with
four thumb nuts.
11. Install monitor vertical brackets to
the back of the monitor using appropri-
ate screws, washers, and optional
spacers for the monitor you are using.
See instruction manual included with the
monitor bracket for details.
12A. Carefully hang the monitor on
the kiosk.
12B. Engage bottom safety screws
to lock monitor bracket together.
Safety Screws
13. Cable clips may be used for
holding wires out of the way.
Ensure Tilt Adjustment
Knobs Are on the Outside