DOM FAMILY Dream On Me 4 IN 1 MINI CRIB 637 User manual

1
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly,keep
out of reach of children until assembly is complete.
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
When contacting Dream On Me you
will need to reference the above
numbers .They can also be found on
the label on the Crib End bottom rail.
To register your product for important safety alerts and updates to your product
please visit www.dreamonme.com and click on Product Registration.
style #: 637
MFG date: Aug,2020
4 IN 1 MINI CRIB
Consumer Care:
www.dreamonme.com
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788
Comes with a mattress.

.
.Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
CAUTION:
Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out.This
crib has an adjustable mattress support For the convenience of the parent when the baby is very
small, the mattress support may be used in the highest position.Important: with the mattress
support and mattress in the highest position, be absolutely sure that the top of the front crib side is
at least 3 inches higher then the top surface of the mattress.If it is not, lower the mattress support
and the mattress to the next highest position.
.Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in(89),
whichever occurs first. The child should be placed in a youth or regular bed.
.
Check this product for damaged hardware, loose joints,loose bolts or other fasteners,missing parts,
or sharp edges before and after assembly and frequently during use.Securely tighten loose bolts
and other fasteners. Do not use crib if any parts are missing,damaged or broken.Contact Dream
On Me for replacement parts and instructional literature if needed.Do not substitute parts.
2
ANY MATTRESS USED IN THIS CRIB SHALL BE AT
LEAST 23 3/4 BY 37 3/4 IN. WITH A THICKNESS NOT
To reduce the risk of SIDS,pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
. Infants can suffocate on soft bedding.Never add a pillow or comforter.Never place additional padding
under an infant.
.
.
Strangulation Hazard:STRINGS CAN CAUSE STRANGULATION! Do not
place items with a string
around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach
strings to toys. Strangulation Hazard: To help prevent strangulation tighten all fasteners.A child can trap
parts of the body or clothing on loose fasteners.
Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
WARNING:
.
.Follow warnings on all products in a crib.
.If refinishing,use a non-toxic finish specified for children’s products.
.Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
.Infants can suffocate in gaps between crib sides and a mattress that is too small.
.Ensure a safe environment for the child by checking regularly, before placing the child in the crib,that
every component is properly and securely in place.
.To avoid head injury, do not allow any child to play underneath the crib.
.Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
.In Canada Only-Use a crib mattress that is no thicker than 15 cm and is of such a size that,when it
is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it
or who is taller than 90 cm.
EXCEEDING 2 IN.

During the assembly process whenever using screws or bolts, check each by placing the screw/bolt
on the diagram of the item which is drawn actual size and design.Be sure to use the proper size and
shape specified in the instructions.
.
.To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON USE:
Keep children and others safe by following these simple rules:
.Do not allow any child to play on furniture.
.Always monitor your child’s activity when in the nursery.
NOTES ON CARE AND MAINTENANCE:
.Do not scratch or chip the finish.
.Do not allow climbing on any piece of furniture.
.Do not allow hanging from any piece of furniture.
.Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or
a damp, cold basement. These extremes can cause a loss of structural integrity.
.Inspect the product periodically, contact Dream On Me for replacement parts or questions.
.To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
.Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
.Do not use abrasive chemicals.
.Do not spray cleaners directly onto furniture.
.Lift slightly when moving on carpeting to prevent leg breakage.
.Use of a vaporizer near furniture will cause wood to swell and finish to peel.
The Product,including side rails,must be fully erected prior to use.
Child can become entrapped and die when improvised netting or covers are placed on top of a play
yard.Never add such items to confine child in play yard.
Always provide the supervision necessary for the continued safety of your child.When used for
playing,never leave child unattended.
Never use a water mattress with this product.
3
NOTES ON ASSEMBLY:
.
.
.
.

=
4

5
PARTS:MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
POUCH ATTACHED TO MATTRESS SUPPORT
-KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
A. Front Rail (1PC) B. Left Front
Leg (1PC)
D. Left Back
Rail Leg (1PC)
C. Right Front
Leg (1PC)
F. Back Rail (1PC)
J. Wooden Mattress Base (1PC)
E. Right Back
Rail Leg (1PC)
G. Left Crib End Bottom(1PC) H. Right Crib End Bottom(1PC)
K. Mattress (1PC)

j.Wrench(1pc)
6
PARTS:
No drills necessary.
Do not use power
screwdriver
Phillips Screwdriver
(not supplied)
a. M6 x 75 mm Allen head Bolt (8pcs)
b. M6 x 55 mm Allen head Bolt (8pcs)
e. BARREL NUT x 16
g. M4 ALLEN WRENCH SUPPLIED
c. M6 x25 mm Allen head Bolt (4pcs)
d. M6 x15 mm Allen head Bolt (4pcs)
r.
Left support brackets (2PCS)
s.
Right support brackets (2PCS)
f. Nut x 4 pcs

M4 ALLEN
WRENCH
SUPPLIED b. M6 x 55 mm BOLT x 8
7
SECTION 1: Crib Assembly
Attach left back leg (D) and
left front leg (B) to left crib end
(G) using M6X55mm bolts ( b)
and barrel nut (e)
Tighten With the M4 Allen Wrench.
Use the Flat HEAD Screwdriver to hold the
Barrel Nut in the proper alignment.
Repeat on the Right Crib.
Fixez la jambe arrière gauche (D)
et la jambe gauche avant (B) sur
la plancheà gauche (G) à l'aide
des boulons (b) .
Assemblez la bonne planche de tête
utilisent de la même manière.
STEP 1
Parts and tools required to complete step.
NOTE: AFTER ASSEMBLY, THE “STEPPED HOLES”
IN BOTH POSTS ARE ON THE SAME SIDE.
e. BARREL
NUT x 8
G. Left Crib End (1PC) H. Right Crib End (1PC) B. Left Front
Leg (1PC)
D. Left Back
Rail Leg (1PC)
C. Right Front
Leg (1PC)
E. Right Back
Rail Leg (1PC)
G
H
D
C
B
E
b
e
e
e
e
e
e
e
e
e
b
b
b
b
b
b
b
B
G

a. M6 x 75 mm BOLT x 4
a
e
e
e
e
a
a
M4 ALLEN
WRENCH
SUPPLIED
e. BARREL NUT x 4
8
SECTION 1: Crib Assembly
STEP 2
Parts and tools required to complete step.
Attach The Front Rail (A) to the assemblies from step 1, using Bolts (a),Barrel Nuts (e) .
Tighten with the Allen Wrench (g) . Use the Flat Head Screwdriver to hold the Barrel Nut in the
proper alignment.
Fixez le rail arrière (A) aux ensembles à partir de l'étape 1, en utilisant les boulons (a), les écrous de barille (e).
Serrez avec la clé Allen (g). Utilisez le tournevis à tête plate pour maintenir l'écrou à barillet dans le
alignement correct.
From Step 1
A. Front Rail (1PC)
H
G
A
a
a
e
H
A

9
SECTION 1: Crib Assembly
STEP3
Parts and tools required to complete step.
J. Wooden Mattress Base (1PC)
c. M6 x25 mm Allen head Bolt (4pcs)
f. Nut x 4 pcs
j.Wrench
r.
Left support
brackets (2PCS)
s.
Right support
brackets (2PCS)
J
JJ
r
r
r
r
s
s
f
f
j
f
f
c
c
c
c
c
X 4
X 4
Attach the Left support brackets (r) and
Right support brackets (s) to the
Wooden mattress base(J)
by using allen head bolts(c) and Nut(f) .
Fixez les supports
gauche (r) et droit (s)
à la base du matelas
en bois (J) à l’aide des
vis à tête à six pans
creux (c) et
de l’écrou (f).

10
SECTION 1: Crib Assembly
STEP 4
Parts and tools required to complete step.
From Step 2
From Step 3
The Warnings printed on the pouch
attached to the mattress support must
face up. This crib has adjustment positions,
use the highest only for new borns, move
the mattress down as the child grows.
WARNING:
Fall Hazard: When child is able to pull to
a standing position,set mattress to
lowest position and remove bumper
pads ,large toys and other objects that
could serve as steps for climbing out.
d. M6 x15 mm Allen head Bolt (4pcs)
g. M4 ALLEN WRENCH
SUPPLIED
Attach the wooden mattress base(J)
to the left back leg(E) and right back
leg(G) and Left Front Leg (F) and
Right Front Leg (H) by using allen head bolts(e).
A
H
G
J
d
d
d
d
d
S
J
AG
X 4

11
SECTION 1: Crib Assembly
STEP 5
From Step 4
Parts and tools required to complete step.
Attach The Back rail (F) and left crib ends
and right crib end
using 75mm allen head bolts (a),
barrel nuts(e) and allen wrench (g) .
Model shown is example only.
Styles may vary .
F. Back Rail (1PC)
a.
a
a
a
a
e
e g
e
e
e
M6 x 75 mm Allen head Bolt (4pcs)
e. BARREL NUT x 4
g. M4 ALLEN WRENCH SUPPLIED
H
G
A
F
F

12
SECTION 1: Crib Assembly
STEP6
From Step 5
Parts and tools required to complete step.
Model shown is example only.
Styles may vary .
Put the mattress(K) into the bed.
K
K. Mattress (1PC)

13
SECTION 2: Day Bed Conversion
STEP 1
Parts and tools required to complete step.
Remove the Front Rail installed in step 5 of section 1 Crib Assembly.
g Allen wrench
Finished Crib
G
H
A

14
SECTION 2: Day Bed Conversion
STEP 2
The mattress support must be in the lowest positions.
Store all hardware safely.

15
SECTION 3: Twin Bed Conversion
Parts and tools required to complete step.
Conversion kit is sold separately
You have the option to convert crib to a twin bed
2.Use the front rail as the
footboard of twin bed.
3.Use the back rail as the
headboard of twin bed.
4.Connect the front rail and the
back rail to the kits ( legs, long
rails,and hardware ) which are
not included and sold separately.
1.Remove the right&left crib end, and leave the legs on the front&back rail, as the parts list shown.
(Hollywood bed frame sold separately)
c:Allen wrench
Split leg (2PCS)
Cross
Bar (4PCS) Side Bar (4PCS)

16
SECTION 4: Converting crib to a twin Bed II
Parts and tools required to complete step.
Model shown is example only.
Styles may vary .
Modèle présenté à titre indicatif.
Les styles peuvent varier.
You have the option to convert crib to a Twin Bed II.
Conversion kit is sold separately
Le Kit de conversion est fourni séparément
Vous avez la possibilité de convertir la crèche à un lit
de taille complète
1.Utilisez le rail de la tête arrière du grand lit.
2.Connectez la plate-forme de pied gauche et la plate-
forme de pied droit sur les rails qui ne sont pas inclus
3.Connectez les pièces assemblées et tête de lit de lit
de taille pour les kits (jambes, longuesrails et le
matériel)
qui ne sont pas inclus et vendus
et vendu séparément.
séparément.
2.Use the left crib end as the
footboard of Twin Bed II.
3.Use the right crib end as the
headboard of Twin Bed II.
4.Connect the left&right crib end
to the kits ( legs, long
rails,and hardware ) which are
not included and sold separately.
1.Remove the front&back rail, and leave the legs on the left&right crib end, as the parts list shown.
(Hollywood bed frame sold separately)
Left Foot Platform
Post (1pc)
Not Supplied
Right Foot Platform Post(1pc) Rail Post(6pcs)
Not Supplied
Not Supplied
Not Supplied

17
To register your product for important safety alerts and updates to
your product please visit www.dreamonme.com
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To report a problem, please log on to www.dreamonme.com and
contact us by phone at 732-366-1788
In the event that you need to contact our customer service
department please have the Style Number and MFG available.
Use the space below to make note of those numbers. They can be
found on the label on the Crib End bottom rail.
STYLE No: 637
COLOR FTY
Lot No:
Pack Date:
Date of Purchase: (you should also keep your receipt)
LIMITED WARRANTY
workmanship and agrees to remedy any such defect.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components
are broken or missing, DO NOT USE

Enter our monthly giveaway!
Simply scan the QRcode to register.
Chat with us!
For any questions or concerns or feedback.
1532, S. Washington Avenue
Piscataway, NJ 08854
E-mail: [email protected]
Customer Care: [phone]
www.dreamonme.com
Follow us on
to get your nursery featured on our social media.
@dreamonmeinc @dreamonmeinc