A: Left Crib End (1PC)
B: Right Crib End (1PC) C: Back rail (1PC) D: Front rail (1 pc)
F: Mattress board (1PC)
E: Stabilizer bar (1PC)
G:Mattress (1PC)
a: 1-1/2” Allen head bolt (8 pcs)
d: 1-1/2” Wood dowel (2 pcs)
b:Barrel nuts (2 pcs)
c:2” Allen wrench (1 pc)
e: Castors (2 pcs) f: Castors (2 pcs)
h: 2-1/4” Allen head bolt (2 pcs)
Follow bellow to fold the crib:
1.take out the mattress (F)
2.take out the mattress board (E)
3.unlock the latch on the headboard
4.fold the crib
Connect Back Rail (C) to the Left Crib End and Right Crib
End (A & B) by Bolts ( a) DO NOT fully tighten the bolts.
STEP 1
STEP 4 STEP 5 STEP 6
B
B
A
A
B
B
B
E
E
F
F
B
E
A
C
C
D
A
G
B
C
Connect rail (D) to the Left Crib End and Right Crib
End (A & B) by Bolts ( a) . THEN FULLY tighten all the bolts.
STEP 2 STEP 3
a
a
e
ff
h
h
h
b
b
b
dx2nx2
n
mx4
m
k
j
j
k
l
l
Slot in the metal pin into the notch of left and
Right Crib End side corner post.then move up and
downo highest level.
Assemble castors (e&f ) to the leg bottoms on the leg
on Back Rail and Front Rail (C&D).2 castors (e) with brake are in
the front.THEN add the mattress(F).
Select the desire level,and use both hand to lift up
the mattress base,then adjust the level to your
require height of the 2 level.Slide in the bolt
underneath the mattress board (E) to keep the
mattress support fixed.
CAUTION:ANY MATTRESS USED IN
THIS CRIB MUST BE
AT LEAST 23-5/8”(600MM) BY 37-3/4”
(959MM) WITH A THICKNESS NOT EXCEEDING 2” (51MM)
. THE CRIB CONFORMS TO
APPLICABLE REGULATIONS PROMULGATED BY
THE CONSUMER PRODUCTS SAFETY
COMMISSION.
i: Latch 1 (2 pcs)
n: Plastic block (2 pcs)
j: Latch 2 (2 pcs) m: 3/4”screw
(4 pcs)
k: 5/8” screw
(6 pcs)
PHILLIPS HEAD SCREWDRIVER
WRENCH
PHILLIPS HEAD SCREWDRIVER
AND WRENCH REQUIRED FOR
ASSEMBLY----NOT INCLUDED
①
②
KEEP INSTRUCTIONS FOR FUTURE USE
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
WARNING
Please note that the warning sticker is placed on the cribs to keep parents and caregivers informed it is a
requirement by law under CPSC and ASTM. We do apologize for any inconvenience this may cause you.
Follow warnings on all products in a crib.
.
WRENCH AND
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
STYLE NO / NUMÉRO DE MODÈLE:684
PORTABLE CRIB / CÈCHE PORTABLE
MFG DATE/
MADE IN CHINA /
MFG CODE SY
Date de Fabrication:JUN 2018
FAIT DANS LA CHINE
Child can become entrapped and die when improvised netting or covers are placed on top of product.
Never add such items to confine child in product.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
www.dreamonme.com
Replace teething rail if damaged,cracked,or loose.
A
D
A
B
a
a
Assemble latch (i & j) to the Left Crib End and Right Crib End (A & B) by
using 5/8” screw (k). Then assemble plastic block(n) horizontal to to the
Left Crib End and Right Crib End (A & B) by using 3/4”screw (m).Tighten screws
using phillips head screwdriver.Make sure that the latch on the bottom of each
head board (A&B) are locked.
Connect stabilizer bar (E)to the Left Crib End and Right Crib End (A & B) by bolts (h) and nuts (b),wood dowel (d).
DO NOT fully tighten the bolts.
1
2
