Dometic MPPT-PRO User manual

MPPT-PRO
BLUETOOTH®
DONGLE
User Manual
GP-MPPT-PRO-BT-1
© 2021 Go Power!
Worldwide Technical Support and Product Information gpelectric.com
Go Power! | Dometic
201-710 Redbrick Street Victoria, BC, V8T 5J3
Tel: [phone]
82805_MANUAL_GP-MPPT-PRO-BT-1

Record the unit’s model and serial number below. It is much easier and quicker to record this information now at the pre-installation stage.
Model Number:
Serial Number:
Date of Install:
Battery Bank Information: (size, install date, battery type)
Product Packaging
Please safely store the packing the product was delivered in or recycle the packaging components as outlined below:
LDPE
Low Density
Polyetheylene
CFB
3
4
7
CFB
3
4
7
CFB
3
4
7
CFB
3
4
7
CFB
3
4
7
Corrugated berboard
main box
Plastic
foam protection
Plastic
accessories bag
www.earth911.com/recycling-center-search-guides
Local recycling centers can be found here:
Corrugated
Recycles
www.corrugated.org
Congratulations on purchasing your Go Power! MPPT Solar Controller Bluetooth Dongle!

gpelectric.com | [page 3]
1. PRODUCT INFORMATION ........................................................................................................................................4
1.1 MAIN FEATURES..............................................................................................................................................4
1.2 LED STATUS..................................................................................................................................................... 4
1.3 APPLICABLE TYPE............................................................................................................................................ 4
1.4 PRODUCT FEAURES .........................................................................................................................................4
1.5 PRODUCT DIMENSIONS...................................................................................................................................5
2. SYSTEM WIRING..........................................................................................................................................................5
3. SPECIFICATIONS ..........................................................................................................................................................6
4. GO POWER! CONNECTTM..........................................................................................................................................7
4.1 GO POWER! CONNECTTM CONNECTIVITY INSTRUCTIONS ................................................................................. 7
4.1.1 DOWNLOAD AND INSTALLATION .........................................................................................................7
4.1.2 BLUETOOTH®DONGLE - PAIRING AND CONNECTING ...........................................................................7
4.1.3 CHANGING THE BLUETOOTH PIN CODE................................................................................................ 7
5. COMPATIBILITY - PHONES AND TABLETS..........................................................................................................8
5.1 ANDROID DEVICES.......................................................................................................................................... 8
5.2 APPLE IOS IPHONES AND IPADS ...................................................................................................................... 8
www.earth911.com/recycling-center-search-guides
CONTENTS

[page 4] | gpelectric.com
The GP-MPPT-PRO-BT-1 makes the GP-MPPT-PRO-60 solar controllers and Bluetooth ready to work seamlessly with the Go Power!
Connect mobile app giving you the ability to wirelessly monitor you controller’s parameters setting and data view
1.1 MAIN FEATURES
1. Convenient wireless monitoring of your solar controller
2. Supports the Go Power! Connect mobile app allowing for simple set-up and plug & play functionality
3. The use of high performance, low power consumption of the bluetooth special chip
4. Adopt Bluetooth 4.0 and BLE technology, has the characteristics of rapid communication and strong anti-jamming capability
5. Does not contain external power supply, powered directly by the communication port
6. Communication distance of up to 15 meters
The MPPT-PRO-60 is only able to accomodate the Bluetooth® Dongle OR the remote. It will not be able to accomodate both.
1.2 LED STATUS
INDICATOR LIGHT STATE EXPLANATION
LINK INDICATOR LIGHT BLINK CONNECTED
OFF IDLE STATE
1.3 APPLICABLE TYPE
APPLY SERIES COMMUNICATION CONTROLLER PORT
All of our controllers employ TTL level
communication and a PH2.0 port TTL PH2.0
1.4 PRODUCT FEATURES
Communication Status Indicator Light
Mounting holes
Communication line
1. PRODUCT INFORMATION

gpelectric.com | [page 5]
2. SYSTEM WIRING
1.5 PRODUCT DIMENSIONS
GP-MPPT-PRO-BT-1
FRONT VIEW
GP-MPPT-PRO-BT-1
SIDE VIEW
57.8
51
51
66.3
15
External Dimensions: 66.3 X 51 X 15 mm
Fixed holes dia: ø3.5
2. SYSTEM WIRING
Note: Cable using the standard Ethernet cable (parallel line) connect.

[page 6] | gpelectric.com
TYPE GP-MPPT-PRO-BT-1
Input voltage 5 - 12V
Stand-by power consumption 0.04W
Run power consumption 0.05W
Communication distance ≤15m
Serial port baud rate Fixed baud rate 9600bps
Communication methods RS232
Interface type RJ12
Connecting line Standard network cable (parallel cable)
Size 66 x 51 x 15.5mm
Installation dimension 57.5 x 15mm
Fixed holes dia ø3.5mm
Operating temperature -20˚C - 75˚C
Level of protection IP67
Net weight 120g
3. SPECIFICATIONS

gpelectric.com | [page 7]
4. GO POWER! CONNECT
4.1 GO POWER! CONNECTTM CONNECTIVITY INSTRUCTIONS
Welcome to the Go Power! ConnectTM manual. You can use the Connect app to configure, monitor and diagnose all our products
which have built-in Bluetooth®capability or are equipped with a Go Power! Direct port.
For a complete list of products compatible with Go Power! Connect, please visit gpelectric.com.
4.1.1. DOWNLOAD AND INSTALLATION
Go Power! ConnectTM is available to users of iOS and Android phones, as well as tablets. Visit get.gpelectric.com/connect to
download the app suitable for your device.
4.1.2. BLUETOOTH®DONGLE - PAIRING AND CONNECTING
1. Open Go Power! ConnectTM
2. On your Phone or Tablet: pull down the screen to initiate a scan for available devices.
3. The first time you attempt to connect the phone will ask to ‘pair’ with the device. Enter the pin code. The default pin code is
000000.
4. Connection is complete.
If connection was not successful please visit https://gpelectric.com/support/battery-monitor-support/.
Always connect from within the Go Power! ConnectTM app. Do not connect from the device’s system menu because the app will
not find your Go Power! product.
4.1.3 CHANGING THE BLUETOOTH PIN CODE
To prevent unauthorised connections to your device we recommended you change the PIN code. Avoid using obvious PIN codes
such as 111111 or 123456.
To change the PIN code: First complete your connection; then go to the Product Info page. To access that page, click the button
on the upper right. For some products it will be the settings icon:
After opening that menu press , and click Product Info
For other products you’ll find the button on the upper right, which takes you straight to the Product Info page.
Go Power! ConnectTM is available on:
Note
•
•
•
i

[page 8] | gpelectric.com
5. COMPATIBILITY - PHONES AND TABLETS
5.1 ANDROID DEVICES
The minimum required Android version to run the Go Power! ConnectTM app is 4.1.
The minimum required Android version to connect to the Go Power! ConnectTM via Bluetooth is 4.3.
Access to location services required?
Android 6 and later requires access permission for the Connectivity app to access location services. Otherwise it can not scan for
the Bluetooth devices.
Besides permitting access to its data, the location services also needs to be enabled in many (but not all) cases.
Note that after enabling location services, the GPS itself can be switched off again: the Android location services are more than
GPS. Bluetooth and WiFi- scan results can technically also be used to approximate the devices location; hence these requirements.
Despite the text above, you can be sure that the Connectivity app is not interested in, nor tracking your location.
5.2 APPLE IOS IPHONES AND IPADS
The Connectivity app works on the following iPhones and iPads, which have Bluetooth 4.0 (BT LE) and iOS 8 or later, which is
required:
• Phone 4S and later (due to Bluetooth Low Energy support)
• iPad 3rd generation and later
Unfortunately Apple iPhone/iPad doesn’t support USB OTG

© 2021 Go Power!
Worldwide Technical Support and Product Information gpelectric.com
Go Power! | Dometic
201-710 Redbrick Street Victoria, BC, V8T 5J3
Tel: [phone]
82805_MANUAL_GP-MPPT-PRO-BT-1