DOMUS Ventillation SDF100 User manual

VENTILATION
Installation Instructions
SDF100/150
Axial Wall Fans
CLEANING
Disconnect power supply before cleaning.
It is important to clean fans regularly as cleaning helps maintain performance and ensure safe, reliable operation.
The front cover can be removed from the fan and gently washed in warm water, dry throughly.
The interior of the fan can be dusted with a soft brush. Do not use water.
On humidity control models, please ensure that no water enters the sensor grille.
OPERATIONS
Timer Adjustment - Timer Models only
Isolate the power supply. The timer is factory set at midpoint. Time is set by placing the black bridge
over 2 of the pins on the right hand side of the timer board. If bridge is not fitted, timer will default to 20
minute setting. Replace front cover BEFORE switching on the power supply.
HUMIDITY ADJUSTMENT - HUMIDITY MODELS ONLY
Isolate the power supply. Remove the front cover. The humidity control adjustment position is clearly
marked. Turn clockwise for less sensitivity and anti-clockwise for greater sensitivity. Turn fully clockwise
to turn the humidity sensor off. Replace front cover BEFORE switching on the fan.
SDF 100 RANGE
230V ac - 50Hz 12W (SDF100) 35W (SDF150)
IPX4 Rating – This product is double insulated.
SDF100B Standard SDF100PB With Pull Cord
SDF100TB With
Timer
SDF100HTB
With Humidistat
and Timer
SDF100HTBPC With Humidistat, Timer
and Pull Cord
SDF100PIR With Movement
Detector and Timer
SDF 150 RANGE
SDF150B Standard SDF150PB With Pull Cord
SDF150TB With
Timer
SDF150 HTBTW Twin Speed with
Humidistat and Pull Cord
SDF150HTB
With Humidistat
and Timer
SDF150HTBPC With Humidistat,
and Pull Cord
SDF150PBTW Twin Speed
and Pull Cord
30 Mins 15 Mins 5 Mins
ISSUE C
LAB038R
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Domus Ventilation
Cambria House, Caerphilly Business Park, Van Road, Caerphilly
CF83 3ED
Tel: [phone] Fax: [phone]
Email: [email protected]
www.domusventilation.co.uk
VENTILATION

SDF 100/150
Window / Wall Fan
These high quality extractor fans are designed to provide effective ventilation and in order
to achieve this, please read these instructions carefully BEFORE installing the fan unit.
Failure to comply with these instructions could reduce the life of the product and may
invalidate the warranty.
This product is suitable for use with up to 1.5 metres of ducting.
WIRING INSTRUCTIONS
It is recommended that the fans be connected into the lighting circuit, with double pole
(3mm) isolation provided before the room light switch and suitably fused, in accordance
with current IEE Regulations.
Window mounted fans should be connected to power supply using a flexible cord with
conductors of between 0.75mm2and 1.5mm2only. Wall and ceiling mounted fans for
fixed wiring should be connected to the power supply via a cable with solid conductors
of 1mm2to 1.5mm2only.
IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
MODELS
SDF100TB
SDF100HTB
SDF100HTBPC
SDF150TB
SDF150HTB
MODELS
SDF100B
SDF150B
MODELS
SDF100PB
SDF150PB
SDF150HBPC
SDF150PBTW
SDF150HTBTW
WARNING: ISOLATE ELECTRICITY SUPPLY BEFORE STARTING WORK
DO NOT INSTALL IN SHOWER CUBICLES (ZONES 0 or 1)
MAXIMUM ROOM TEMPERATURE 40ºC
WARNING: ISOLATE ELECTRICITY SUPPLY BEFORE STARTING WORK
FITTING WALL FAN
1. Select a suitable position for the fan
keeping the ducting as short and straight
as possible.
2. Cut a hole in the wall or ceiling to suit the
outside diameter of the ducting.
3. Remove the front cover from the fan
by undoing the retaining screw at the
bottom edge of front cover. Position the
fan backplate and mark the retaining
screw positions.
4. Remove the appropriate cable entry
knock out position from the fan
backplate and thread power cable
through before fixing the fan to the wall
or ceiling.
5. Ceiling mounted fans must be installed
with a condensation trap.
Note: Fans fitted with pull cord switches are
not suitable for ceiling mounting.
Note: All the ancillary items can be obtained
through Domus stockists.
call [phone]
to find your nearest stockist
To access terminals
on these models,
lift off control cover
S/L N L N L N L
S/L N L N L N L
Operating
Switch
Operating
Switch
Isolator
Switch
Isolator
Switch
L = LIVE N = NEUTRAL S/L = SWITCH LIVE
Pipe vented to
outside
Condensation
Trap
Vertical exit through roof void