Donovan Sidewinder User manual

READ BEFORE INST
ALLING
3353 GRAN PARK WAY • STUART, FL 34997
PHONE: [phone] • FAX: [phone]
www.DONOVAN-TARPS.com
TARP SYSTEMS, PARTS & TARPS
Electric Side-Flip Tarp System
P/N 1809453 Rev. A

DONOVAN
®
HELP LINE: 1-800-327-8287
PREPAID FREIGHT POLICY. Shur-Co®, LLC will prepay freight on eligible
orders* of Florida-manufactured Donovan®products and tarp items shipped
from our Florida branch that meet the dollar requirements for the shipping
destinations specifi ed below.
*Valid within the continental 48 states only. Applies to products purchased at standard pricing; any
special pricing will void standard prepaid freight policy and will be addressed on a case-by-case
basis. Does NOT apply to complete Waste systems or ShurTite™ fl atbed products. To see a list of
eligible products consult the Index of the Donovan® Tarp Systems catalog.
INTO FL: Freight prepaid on orders of $2,500 or more or tarp-only orders of
$1,500 or more. INTO ZONES 1 & 2: Freight prepaid on orders of $3,000
or more or tarp-only orders of $2,500 or more. INTO ZONES 3 & 4: Freight
prepaid on orders of $6,000 or more or tarp-only orders of $3,000 or more.
WARRANTY. We warrant all new products are free of defects in materials and
workmanship.* This warranty is effective if products are properly installed and
used for the purpose for which they were intended and applies to the original
buyer only. Except as set forth above or in any product-specifi c warranty docu-
mentation, we make no other warranties, express or implied, including but not
limited to warranties of merchantability of fi tness for a particular use.
Returns of a product for warranty must be accompanied by a Return Merchan-
dise Authorization number (RMA#), obtained by by calling Customer Service
at 800-327-8287, and sent, freight paid by us, to Donovan, 3353 SE Gran Park
Way, Stuart, FL 34997. All products returned without an RMA# will be refused.
When we issue the RMA#, we will also issue a call tag to have U.P.S. (or
other freight company) pick up the product. C.O.D. returns not accepted.
We will pay no storage fees for a warranty product return prior to pick by us
or the freight company. If a warranty product return is scheduled to be picked
up by us, we will pick up the product at our earliest convenience. If a product
returned is found, in our judgement, to be defective in material or workman-
ship, our obligation under this warranty is limited to the repair or replacement
of the product, which will be made by us. Repair or replacement will be at our
discretion, with replacements being made using current products performing
in the equivalent function. Labor charges, other than those incurred at our fac-
tory, including, but not limited to, any labor to install a repaired or replacement
product, are not covered under this warranty. All expenses associated with
delivering defective products to our factory and delivering repaired or replace-
ment products from our factory to the owner will be paid by us.
If the product returned is found, in our judgement, to be non-warrantable, the
owner will be contacted to authorize repair work, purchase of a replacement
product or return of the product, all of which will be at the owner’s expense.
Payment authorization must be received by us before any non-warrantable
product is repaired, replaced or returned. All expenses associated with deliver-
ing the repaired non-warrantable product, a replacement product or the non-
warrantable product from our factory to the owner will be paid by the owner.
In no event will we be liable for any damages of any kind to person, product or
property, including but not limited to indirect, incidental, special, consequential
or punitive damages, or damages for loss of profi ts or revenue, even if we
have been advised of the possibility of such damages. There are no warran-
ties for used products or products that have been repaired, altered, modifi ed
or subjected to misuse, negligence or accident. We will not repair or replace
products that fail or malfunction due to ordinary wear and tear, except as ex-
pressly noted in a product-specifi c warranty. Use of non-Shur-Co®, LLC parts
in conjuction with Shur-Co®, LLC products will void this product warranty.
*Certain products have specifi c warranties that differ from this warranty, for example motors and elec-
tronics. Product-specifi c warranty documentation is available for these items. In the event of a confl ict
between this warranty and a product-specifi c warranty, the product-specifi c warranty will govern.
RETURN POLICY. All sales fi nal. See WARRANTY above for return details.
OTHER. All prices, product listings, sizes, weights and manufacturing details
are subject to change without notice. No person is authorized to modify the
foregoing conditions of sale whatsoever.
ZONE 4 ZONE 3 ZONE 2
ZONE 1
FL
FL
M
MI
Shur-Co®, LLC Terms & Conditions
SHUR-CO®, LLC SERVICE AND DISTRIBUTION CENTERS
Corporate HQ
SHUR-CO® of SOUTH DAKOTA
2309 Shur-Lok St., Yankton, SD 57078
Ph 800.474.8756 | Fax [phone]
SHUR-CO®of IDAHO
610 N. 16th Ave., Caldwell, ID 83607
Ph 866.356.0246 | Fax [phone]
SHUR-CO® of ILLINOIS
3993 E. Mueller Ave., Decatur, IL 62526
Ph 866.356.0246 | Fax [phone]
Preferred Donovan®Brand Seller
SHUR-CO® of FLORIDA
3353 SE Gran Park Way, Stuart, FL 34997
Ph 800.327.8287 | Fax [phone]
SHUR-CO®of NORTH DAKOTA
1746 4th Ave. NW, West Fargo, ND 58078
Ph 877.868.4488 | Fax [phone]
SHUR-CO®of OHIO
4676 Lynn Rd.
Rootstown, OH 44266
Ph 866.356.0242 | Fax [phone]
SHUR-CO® of VERMILLION
1212 N. Norbeck St., Vermillion, SD
Ph 605.658.1020 | Fax [phone]
SHUR-CO®of CANADA
490 Elgin St., Unit #1
Brantford, Ontario N3S 7P8
Ph 800.265.0823 | Fax [phone]
SHUR-CO®UK, Ltd.
Unit 41 Rochester Airport Estates
Laker Rd., Rochester, Kent ME1 3QX
Ph +44 (0)1795.473499
Fax [phone]
For more information, log on to our website:
www.donovan-tarps.com
P/N 1809453 Rev. A
2

DONOVAN
®
HELP LINE: 1-800-327-8287
Sidewinder™ Electric Side-Flip Tarp System
P/N 1809453 Rev. A
Hardware Identication.......................................................................4
Actuator Unit Installation.....................................................................5
Hydraulic Installation (Electric/Hydraulic) ...........................................6
Hinge Installation/Lid Extensions Assembly .......................................7
Lid Installation.....................................................................................8
Cable and Tarp Installation.................................................................9
Hydraulic Schematic (Wet Kit)..........................................................10
Operation and Maintenance ............................................................. 11
Replacement Parts...........................................................................12
1. Wrench Set
2. Ratcheting Socket Wrench
3. Socket Set
4. Hammer
5. Tape Measure
6. Flat Head or Phillips Screwdriver
7. Grinder
8. Pliers
9. Metal Saw
10. Steel Welder
11. Drill Driver with 5/16" Hex Driver
12. Allen Wrench
13. Square
Thank you for buying this tarping system from Donovan®Tarps. We
appreciate your condence in our products. Please read and thor-
oughly understand this manual before installing and/or operating this
system.
Pay particular attention to important safety and operating instructions,
as well as warnings and cautions. The hazard symbol ! is used to
alert users to potentially hazardous conditions and is followed by cau-
tion, warning or danger messages.
Failure to READ AND FOLLOW INSTRUCTIONS could result in fail-
ure of your tarping system and/or personal injury. Your trailer require-
ments may, however, call for minor variations to these instructions.
Please inspect your tarping system periodically. Repair or replace
worn or damaged parts to your system.
QUESTIONS? CALL OUR HELP LINE:
1-866-748-7435
MON-FRI 8 AM-5 PM CENTRAL TIME
We at Donovan® Tarps are concerned with your safety and the safety
of all those operating this system. Therefore, we have provided safety
decals at various locations on your tarping system. Keep decals as
clean as possible at all times. Replace any decal that has become
worn or damaged, painted over or otherwise difcult to read. Replace-
ment decals are available through Donovan® Tarps dealers.
To prevent rust, paint all exposed metal, such as weld seams and/or
metal exposed by grinding or cutting, with corrosion-resistant paint.
TOOLS REQUIRED
RUST PREVENTION
SAFETY
TABLE OF CONTENTSMESSAGE TO OWNERS
3
1. Always wear safety glasses during instal-
lation and operation.
2. Stay clear of moving parts.
3. No other use of this system is authorized,
except as designed.
SAFETY INSTRUCTIONS

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
4
Hardware Identication
AAGG
BBHH
CCJJ
EE
FF
DDKK
LL
MM
1800790 Cap Screw - 3/8" x 1-1/2" (Gr. 5)
1801224 Self-Tapping Screw - 1/4" x 3/4"
1705032 Cap Screw - 3/8" x 4-1/2"
1800901 Cap Screw - 1/2" x 3" (Gr. 5)
1800993 Nylock Lock Nut - 3/8"
1800995 Nylock Lock Nut - 1/2" (Gr. 5)
1800994 Flat Washer - 3/8"
1800996 Flat Washer - 1/2"
1800246 Stainless Steel Flat Washer 1/2"
1809282 Spacer - 5/8" OD x .385" ID x 3.562" LG
1800245 Button Head Cap Screw - 1/2" x 2" (SS)
1800374 Button Head Cap Screw - 1/2" x 3" (SS)

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
5
Actuator Unit Installation
E
NOTE: Actuator unit weighs 134 lbs (64kg). Use over-head
lifting device and sling to lift unit. Sling should be wrapped
around rectangular mounting bracket. Do not lift from
hydraulic cylinder.
Actuator unit may be welded in place to steel trailer, use
extreme caution to protect chrome cylinder rod from weld
splatter. Will cause permanent damage to cylinder and void
systems warranty.
NOTE: If front wall of trailer is thin aluminum or steel.
Reinforce area with backer plate for adequate support.
STEP 1: Locate actuator unit on front of trailer. Stationary rect-
angular tube should be 8.5" from top of trailer and 9.5" in from
drivers side of trailer. Mark mounting holes locations on each of
four mounting plates.
STEP 2: Remove actuator unit and drill 17/32" holes in marked
locations.
STEP 3: Reposition actuator unit and mount using 1/2" Grade 5
bolts or better (bolts not supplied).
STEP 5: Install windshield using braces, bolts DD and EE, washer
LL and nuts HH.
STEP 4: Connect two provided 37.5" hydraulic hoses to cyl-
inder. If using wet kit, refer to page 10 for two longer hoses
provided.
8.5" (21.6 CM)
TOP OF
TRAILER
LIFTING
POINT
WINDSHIELD
1-1/2" BRACE
1" BRACE
9.5" (24.1 CM)
H
LD

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
6
Hydraulics for Electric/Hydraulic Systems
NOTE: Included hydraulic hoses are roughly 3' long.
NOTE: Skip to page 10 if using wet kit.
STEP 1: Using pump mount bracket as template, locate and
mark where hydraulic unit will mount - approximately 1' below
actuator unit.
STEP 2: Remove pump mount bracket and drill 13/32" holes in
marked locations.
STEP 3: Install pump mount bracket using 3/8" bolts BB, wash-
ers JJ and lock nuts GG.
STEP 4: Install two rubber bumpers to pump mounts bent tabs
and mount pump itself using included 3/8" studs, lock nuts JJ
and washers GG.
STEP 6: Connect two hydraulic hoses between pump and cyl-
inder. Port C2 to cap end of cylinder and Port C1 to rod end of
cylinder. Use hose clips and self-drilling screws AA to organize
and secure hoses to trailer.
STEP 7: Mount control switch using two self-drilling screws AA.
Connect control switch to pump solenoid wiring harness. Se-
cure quick disconnect power cable near control switch. Use
hose clips and self-drilling screws AA to organize and secure
cables to trailer.
J
A
STEP 5: Secure bottom of reservoir to mount bracket with in-
cluded 5-7" adjustable hose clamp.
NOTE: Under normal operating conditions uid will last
life of pump. In extreme dirty or wet conditions, check uid
every four to six months and change as needed.
STEP 8: Install all provided safety stickers next to control switch.
Stickers detailed on page 11.
STEP 9: Remove red cap from ller neck on reservoir and ll
with approximately three quarts (2.83 Liters) of Dextron Auto-
matic Transmission uid. Replace red cap with black breather
cap.
STEP 10: Connect a 12V power supply to quick disconnect
power cable and cycle cylinder ten times to remove any air in
system. Failure to do this may result in personal injury and/or
damage to Sidewinder™ system.
MOUNTING BRACKET
CABLE MUST
EXIT AT BOTTOM
PUMP
ROD ENDCAP END
RUBBER
BUMPERS
CONTROL
SWITCH
G
J
B
1 1
2 2
3 3
4
5
Item Part # Description
1. 1800925 Elbow 90º - #4 JIC M x #6 ORB M
2. 1800112 Elbow 90º - #4 JIC M x 1/4" NPT M
3. 1801235 Hydraulic Hose - 37-1/2" OAL
4. 1800850 Hydraulic Pump - 12V
5. 1800205 Hydraulic Cylinder - 15-1/2" Stroke

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
7
Hinge Installation/Lid Extension Assembly
NOTE: For trailers with center support above top rail, offset
center hinge to either side of support.
STEP 2: Locate front, center and rear hinge positions. Weld
hinges in place to steel trailer. Use caution to protect chrome
cylinder rod from weld splatter. Skip Steps 3-5 if hinges are
welded.
STEP 3: Locate front, center and rear hinge positions. Mark
hinge hole positions.
STEP 4: Remove hinges and drill 17/32" (13.5mm) holes in
marked locations on side of top rail. Drill and tap marked loca-
tions on top of top rail for 1/2" bolts .
STEP 5: Reposition hinges and mount using 1/2" Grade 5 bolts
or better (bolts not supplied).
STEP 1: Lid hinges may be mounted either by welding or by
bolts. If welding, move to Step 2. If bolting,skip to Step 3.
STEP 1: Starting with front lid, noted by having a C-channel and
additional gussets, measure outside-to-outside width at front of
trailer at top rail. Slide extension tube into front lid matching this
measurement then weld in place.
APPROX. CENTER
LINE OF TRAILER
WIDTH AT FRONT
OF TRAILER
APPROX. CENTER
LINE OF TRAILER
8" (20.3 CM)
8" (20.3 CM)
8.75" (22.2 CM)
8.75" (22.2 CM)
HINGE INSTALLATION LID EXTENSION ASSEMBLY
NOTE: Orientation of angle will be pointing toward ground
when lid is mounted to trailer.
STEP 2: Repeat process measuring outside-to-outside width at
center and rear of trailer. Adjust extension tubes for center and
rear lids respectively.
NOTE: Center lid extension will not have a cable attached,
but will get two turn-buckles at a later step. The rear lid has
no C-channel or additional gussets as compared to front lid.
ANGLE POINTS DOWN
WELD FOUR SIDES

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
8
Lid Installation
STEP 1: Install roller and shaft onto actuator arm using c-clip
and shim.
STEP 6: Assemble two to three ladder sections and “H” con-
nectors to obtain nal length of front lid from previous step. If
needed, cut ladder to length. Ensure cut is at least 4" (101.6mm)
away from nearest rung so there is enough remaining to insert
into lids.
STEP 7: Mark ladder 4" (101.6mm) in on each end. Lift and
slide front ladder section into front and center lids until each
has been inserted a minimum of 4". Weld all four sides of each
ladder to front and center lids. Note underside will be welded in
Step 8.
STEP 8: Repeat process for rear ladder using nal length for
the rear ladder from Step 5. Open system to access underside
of ladder to nish welding.
STEP 5: With all three lids in closed position, measure distance
between lids and add 8" to get the nal length of each ladder
section.
STEP 2: With actuator arm near fully open position, slide front
lid roller track over roller and pivot into alignment. Attach to hing-
es with bolts FF, washers, KK and lock nuts HH.
STEP 3: Install spacer MM into roller track using bolt CC, washers
JJ and lock nut GG.
STEP 4: Repeat Step 2 for center and rear lids using two and
four bolts respectively to connect to their hinges.
NOTE: This may slide as needed through actuator arm in
order to line up with front lid roller track.
ROLLER
LADDER SECTION LADDER SECTION
“H” CONNECTOR
WELD (4) SIDES
WELD (4) SIDES
WELD (4) SIDES
4" INSERTED
4" INSERTED
4"
FINAL LENGTH FROM STEP 2
SHAFT
C-CLIP
SHIM
ACTUATOR
K
FK
H
FRONT
LADDER
REAR
LADDER
MEASURED
+8" =
MEASURED
+8" =
G
M
C
J
J

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
9
Cable and Tarp Installation
STEP 1: Open lid to lay at on side of trailer. Locate two 30'
cables with turnbuckles. Fully extend turnbuckles. Hook each
turnbuckle into center lid extension.
STEP 6: Carefully actuate lid to vertical position, ensuring mesh
does not snag or catch anything. In vertical position, tarp should
hang from cable down to lid’s ladders. Attach tarp to ladder us-
ing provided zip ties, every 12-18" (30.5-45.7cm).
STEP 8: For trailers shorter than tarp length, cut tarp at back of
trailer with approximately 6-8" (15.2-20.3cm) of extra material to
be folded over and zip tied along rear lid.
STEP 7: Attach tarp along front lid with provided zip ties. Use
holes and D-ring on front lid.
STEP 3: Tighten both turnbuckles evenly until cable are taught.
Do not over tighten turnbuckles as this may cause excess stress
on lids and hinges. Apply small amount of liquid thread locker to
turnbuckle jam nuts and tighten to prevent loosening.
STEP 4: Lay out mesh tarp in a clear open area to verify dimen-
sions and tarp condition.
STEP 5: With lid still in fully open position, start attaching tarp
to cable only. Start at front lid using zip ties every 12-18" (30.5-
45.7cm).
STEP 2: One cable will attach to front lid, second cable will at-
tach to rear lid. These are attached using 3/16" timble and two
3/16" cable nuts.
NOTE: If there is a large gap between rear lid and trailer
rear door, do not cut any of excess tarp materials. Roll up
the excess and zip tie to rear lid to help cover gap.
NOTE: 2" wide splicing tape can be used to protect tarp by
wrapping a small length around any sharp points on system
of truck.
CENTER LID
EXTENSION
CABLES W/
TURNBUCKLES
CABLE
FRONT OR
REAR LID 3/16" TIMBLE
3/16" CABLE NUTS
ZIP TIES
ZIP TIES
ZIP TIES

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
10
Hydraulic Schematic (Wet Kit)
Item Part # Description
1. 1809922 Reducer - 1/4" NPT F x #10 ORB M
2. 1809913 Elbow 90º - #4 JIC M x #8 ORB M
3. 1800112 Elbow 90º - #4 JIC M x 1/4" NPT M
4. 1809921 Reducer - 1/4" NPT F x 1" NPT M
5. 1809914 Male Branch Tee - 1" NPT M
6. 1809923 Elbow 90º - 1/4" NPT M x 1/4" NPT F
7. 1801017 Adapter - 1/4" NPT M x #4 JIC M
8. 1800912 Elbow 90º - 1/4" NPT M x 1/4" NPT M
9. 1809915 Reducer - #8 ORB M x 1/4" NPT F
10. 1809924 Hex Nipple - 1/4" NPT M x 1/4" NPT M
11. 1809916 Hose - 1/4" x 5' - #4 JIC F Ends
12. 1809917 Hose - 1/4" x 8' - #4 JIC F Ends
13. 1809918 Hose - 1/4" x 9' - #4 JIC F Ends
14. 1809919 Flow Control - 1/4" NPT F
15. 1800471 Control Valve - 1 Spool
16. 1809520 Flow Diverter
17. 1800205 Hydraulic Cylinder - 15-1/2" Stroke
ROD END
FLOW DIVERTER
HYDRAULIC PRESSURE
LINE FROM TRUCK
HYDRAULIC PRESSURE
LINE TO TRAILER
HYDRAULIC RETURN
LINE FROM TRAILER
HYDRAULIC RETURN
LINE TO TRUCK’S TANK
CAP END
B
A
PT
B
R
P
T
17
3 3
7
13
14
8 9
2
11
5
6 9
3
1
11
16
2
7
14
15
10
4
3
12

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
11
Operation and Maintenance
NOTE: Noise level is less than 72 dB(A).
CAUTION
Before operating this or any tarper, check your
surroundings for any overhead power lines
tree limbs or other obstruction in path of tarper
travel from open to close and back.
!
CAUTION
Before servicing or repairing Sidewinder™
system, disconnect power to components from
vehicles battery or other power source.
!
Periodic Maintenance and Inspections
Daily:
1) Check actuator for any damage or cracks
2) Check tarp for excessive wear and tear
3) If equipped check electrical cables for insulation damage
4) Check hydraulic hoses and ttings for damage or leaks
5) Check tarp cables and adjust if loose
Weekly
1) Check hydraulic cylinder for leaks or wear
2) Check tightness of fasteners
3) Check hinges for excessive wear/looseness
4) If equipped check hydraulic uid level in hydraulic reservoir
To Open Tarp
Press UP on switch lever to open lid.
To Close Tarp
Press DOWN on switch lever to open lid.

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
12
Replacement Parts
SIDEWINDER™
Item Part # Description
1. 1800286 Backhoe Actuator Assembly - Left Hinge
(includes items 4; 5; 6; 14; 16; 17; 22; 23;
24; 25; 2 of 3, 7, 8, 9, 10, 26, & 27; 4 of 21)
2. 1801907 Backhoe Actuator Assembly - Right Hinge
(includes items 4; 5; 6; 14; 16; 17; 22; 23;
24; 25; 2 of 3, 7, 8, 9, 10, 26, & 27; 4 of 21)
3. 1800276* Gearlock Bearing
4. 1800282 Cylinder Mount
5. 1800287 Base Tube Weldment
6. 1800292 Cylinder Base Pin Assembly
7. 1800880 External Retaining Ring - 1-1/2" Dia.
8. 1801707* External Retaining Ring - 1" Dia.
9. 1800112 Hydraulic Fitting - #4 JIC x 1/4" NPT 90º
10. 1800180 Short Link Assembly (includes 11; 12; 13)
11. 1800497 Bushing - 1" ID x 1-1/4" OD x 1"
12. 1800879 Bushing - 1-1/2" ID x 1-3/4" OD x 1"
13. 1800181 Short Link
14. 1800190 Long Link w/Bushing (includes 11; 12; 15)
15. 1800191 Long Link
16. 1800194 Pin Connector
17. 1800197 Rotating Arm Assembly
(includes 19; 20; 2 of 7, 18 & 21)
18. 1800156 Bushing - 1-1/2" ID x 1-3/4" OD x 2"
19. 1800199 Rotating Arm
20. 1800203 Bushing - Turned
21. 1800204 Shim - 1-1/2" ID x .047"
22. 1800205 Hydraulic Cylinder - 2-1/2" x 15-1/4"
23. 1800207* Short Link Spacer
24. 1800208 Long Link Pin
25. 1800211 Long/Short Link Pin
26. 1800232 Hex Bolt w/Serrated Washer - 5/8" 1-1/2"
27. 1800250* Shim - 1" ID x 1-1/2" OD x .047
28. 1800289 Front Lid Assembly
29. 1800293 Wind Deector
30. 1800294* Deector Brace - 1-1/2"
31. 1800295* Deector Brace - 1"
32. 1800335 Roller Shaft Assembly - 10"
(includes 33; 34; 35; 36; 54; 2 of 27)
33. 1800331 Roller Shaft
34. 1800977* Shim - 1-1/4" ID x .047"
35. 1800978* Retaining Ring - 1-1/4"
36. 1800177 Roller - UMHW
37. 1800374* Stainless Button Head Screw - 1/2" x 3"
38. 1800872 Cable Nut - 3/16"
39. 1800923 Loop Strap 3/4"
40. 1801379* Loctite™ - 5ML - Tube
41. 1801510* Bumper Stripes - UHMW
42. 1800897 Center Lid Extension
43. 1801236 Rubber Bumper - 1-1/2" Round
44. 1801276 Cable w/Turnbuckle - 30'
45. 1801342* Solenoid Cover - SL
46. 1801495* Clamp Hose - 4-1/16" x 5"
47. 1800412 Pump Mount Bracket
48. 1800884 Rear Lid Assembly
49. 1800885 Center Lid Assembly
50. 1800889 Ladder Assembly
51. 1800945 Pump Assembly - 12V
(includes 52; 53; 54; 58; 2 of 43, 55, 56, & 57)
52. 1800458* 150-Amp Circuit Breaker
53 1800850 Hydraulic Pump - 12V M3551
*These items are NOT shown in the drawing: numbered for future reference
Continued to Next Page. ->
1
13
25
25
49
7
7
7
19
43
2
14
14
26
26
38
50
74
20
32
44
15
39
9
9
9
21
21
21
33
4
4
16
16
28
64
10
10
22
22
58
5
5
17
17
29
65
11
6
6
18
42
12
12
24
24
36
48

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
13
Replacement Parts
SIDEWINDER™ (CONT.)
Item Part # Description
54. 1800906 Clamp 5" to 7"
55. 1800925 Male Hydraulic Fitting - #6 x 90º
56. 1800926* Stud - 3/8" x 2-5/8"
57. 1801235 Hydraulic Hose - 37-1/2" OAL
58. 1801237 Wiring Harness - 9' (includes 59; 62; 2 of 60)
59. 1800149* Connector - 120 Amp - 4 Ga.
60. 1800158* Ring Terminal - 4 Ga. x 3/8" Stud - Battery
61. 1800221* Dual-Conductor Wire - 4 Ga. - 9'
62. 1801238 Wiring Harness - 16' (includes 59; 62; 2 of 60)
63. 1800220* Dual-Conductor Wire -4 Ga. - 16'
64. 1801233* 4H Connectors (includes 4 of 65)
65. 1800891 Connector - H
66. 1801599 Front & Rear Hinge Assembly - Low Prole
(includes 72; 2 of 67, 70; 4 of 68)
67. 1800606 Hinge Pin Assembly
68. 1800860 Flanged Bushing - 1-1/4" ID
69. 1801600 Rear Hinge - Low Prole
70. 1801603 Hinge Lid - Low Prole
71. 1801601 Center Hinge Assembly - Low Prole
(includes 67; 69; 70; 2 of 68)
72. 1801602 Center Hinge - Low Prole
73. 1800315* Hose Bundle Wrap - 1/2"
74. 1800497 Bushing - 1" ID x 1-1/4" OD x 1/2"
75. 1808766 External Retaining Ring - 1"
76. 1801430* Sidewinder™ Wet Kit
*These items are NOT shown in the drawing: numbered for future reference
55
67
67
68
68
51
57
57
69
58
70
70
53
71
54
66
72

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
14
Notes

DONOVAN
®
HELP LINE: 1-800-327-8287
P/N 1809453 Rev. A
15
Notes

CONSTR
UCTION PRODUCTS
• Arm-Matic™
• Flash™
• Bullet™
• Hammer™ II
• DuraPull™
• 5000X
• UT Tarp System™
• 2000SR
WASTE PRODUCTS
• SWAT®
• Quick-Flip™ III
• Sidewinder™
• Sidewinder™ 350
• Hy-Tower™ SL
• Hy-Tower™ DL
• Double-Flip™
• Donovan® Belt & Ratchet (DBR)
MORE QUALITY PRODUCTS FROM DONOVAN®
TARP SYSTEMS, PARTS & TARPS