Doorson 300 THALES User manual

USER MANUAL
AUTOMATIC SLIDING DOOR PRODUCT LINE 300
1/25/2016
product line

3 I USER MANUAL
CONTENT
INTRODUCTION ................................................................................................4
MANUFACTURER CONTACT ....................................................................................5
PRODUCT DESCRIPTION .......................................................................................5
PRODUCT PURPOSE ...........................................................................................6
TECHNICAL DATA ..............................................................................................7
MAXIMUM DOOR DIMENSIONS AND WEIGHTS ...........................................................7
PRODUCT LINE 300 ............................................................................................8
SAFETY RECOMMENDATIONS ..................................................................................9
DOOR OPERATION ............................................................................................10
MODE SELECTION ......................................................................................10
COM20 ................................................................................................11
COM21 ................................................................................................11
ADDITIONAL ENTRIES ..................................................................................12
IN CASE OF POWER FAILURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
EXIT AND ENTRANCE INTO THE BUILDING...............................................................13
ENERGY SAVE ..........................................................................................13
REDUNDANCY TESTING ................................................................................14
FIRE SIGNAL ..................................................................................................15
ELECTRIC LOCK EL5 ...........................................................................................16
FIRST STARTUP ...............................................................................................17
TYPE 300 A ...................................................................................................18
NORMAL OPERATION OF 300 A .........................................................................18
ACTIVATION OF THE BREAK-OUT FUNCTION ............................................................19
POSSIBILITY OF ENLARGING THE PASSAGE OPENING....................................................19
TYPE 300 F AND 300 EF ......................................................................................20
INTENDED USE OF 300 F ...............................................................................20
INTENDED USE OF 300 EF .............................................................................20
FIRE DOOR OPERATION ................................................................................21
SYSTEM SETTINGS ............................................................................................22
LIGHT AND SOUND DIAGNOSTICS .............................................................................23
DURING OPERATION ...................................................................................23
DURING WARNING .....................................................................................23
DURING ERRORS .......................................................................................24
HANDLING DURING ERRORS............................................................................25
WARNINGS ............................................................................................26
ERRORS ...............................................................................................28
TRANSPORT AND STORAGE ...................................................................................29
MAINTENANCE ...............................................................................................30
UNINSTALLATION, REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
SERVICE INFORMATION .......................................................................................31
MARKING .....................................................................................................31

INTRODUCTION
Dear client,
we would like to thank you for your purchase. You will find that you can rely on our products.
The purpose of the detailed instructions is to better acquaint you with the automatic door system of
the product line 300 so that you may make better use of it. We recommend that this manual is kept
somewhere close to the door.
4I USER MANUAL
Important safety instructions. It is important for the safety of persons to follow these
instructions. Save these instructions.
NOTE: the additional code (W) is the code for the wooden alternative of the doors.
Automatic sliding doors Doorson product line 300 must be installed in accordance with the instructions
for installation. The automatic systems of the product line 300 serve for automatization of passages. This
allows unhindered passage from the exterior into the interior area and vice versa. In this way we achieve
selectivity, automatism, modernization, aesthetic appearance and a wide range of uses.
Easier passage with the help of the automatic system offers comfort, rationalization in heating of the
premises, and for disabled persons this is the only way that allows independent passage through the door.
The system works safely even in extreme conditions, increased frequency of opening and temperature and
climatic changes. The computer-supported technology provides diverse functionality and greater reliability.
The system’s modern design has all the advantages that enable people to improve their standard of living.
Implementation of the high technology allows for many various functions of opening and closing the door.
The locks prevent unwanted intrusion and the one-way passage ensures selectivity. Partial opening of the
door saves energy during low temperatures. The various uses of the sensors provide free passage, while
safety is ensured by sensors for presence and special and spot sensors. The program’s flexibility allows
adjustment of the desired speed and time of open doors.
With a high degree of innovation and knowledge we are constantly developing new products and our goal
this time was to develop energy-saving automatic sliding doors product line 300 which drastically reduce
electricity costs and thus classify buildings as environmentally friendly.
Energy-efficient sliding doors DOORSON product line 300 think advanced and act green. When our doors
are in a “CLOSED” or “OPEN” operating mode for more than 9 seconds, they exclude the supply of voltage
and remain on battery support with reduced power consumption of less than 0.5W. Only certain functions
for the reactivation of the doors are carried out.
After the completion of the tests, calculations have shown that our automatic sliding doors in idle state
(stand-by mode) consume less than 0.5W of electricity. (ZAG report - Slovenian National Building and Civil
Engineering Institute, where we also received the necessary approval and certificates)
Compared to the competition in the market, automatic doors product line 300 consume 70% less electricity
and reduce CO2 emissions by 70%.
Before first use, carefully read the entire instructions and pay attention to the listed safety
recommendations! The instructions include the entire product line 300.

5I USER MANUAL
DOORSON d.o.o.
Milenkova ulica 9
2000 Maribor
Slovenia, Europe
T: [phone]
F: [phone]
E: [email protected]
W: www.doorson.com
Doorson company
PRODUCT DESCRIPTION
Automatic sliding doors product line 300 consist of an intelligently regulated modern drive mechanism.
The door controller allows you to use a wide range of accessories (mode selectors, motion and presence
sensors, safety sensors, battery units, electric locks, anti-burglar switches, keyboards, remote controls,
magnetic card readers, connection to the fire safety system…), which ensure high operation safety and
integration with smart building systems.
Product line 300+
MANUFACTURER
CONTACT

PRODUCT PURPOSE
Automatic sliding doors product line 300 can be used as interior or exterior doors. The drive is advised to
be installed inside the building, otherwise a canopy is recommended. In the product line 300 the 300F and
300EF doors are fireproof doors. The 300 THALES r, 300 r, 300 T r, 300 P r, 300 SC r, 300 C r, 300 A and
300 EF are suitable for the installation on escape routes and emergency exits.
Automatic sliding doors product line 300 may only be used according to its specified intended use.
Doorson will not accept any liability for damage resulting from unauthorized modification of
product line 300 or inappropriate use. Furthermore, components/accessories that have not been approved
by Doorson are exempted from liability.
It is important for the safety of persons to follow these instructions:
do not allow children to play with automatic doors;
always escort children when walking through automatic doors;
frequently examine the door status (signs of wear, inadequate functioning and damage to
cables or moving parts). Do not allow door operation if repair or adjustment is necessary;
disconnect the power supply (230VAC and battery unit) during maintenance works inside
the drive;
change the door mode to STOP during the cleaning of the door leaves;
follow all instructions since incorrect installation can lead to severe injury;
properly ground the door leaf/leaves if Product line 300 is installed on a metal
construction;
door leaves with glass must be made of safety glass;
there should be no contact between glass and hard materials during operation if the leaves
are made from glass only.;
During the planning of automatic sliding doors product line 300, the manufacturer (the person installing
the system) and the commissioner/facility operator have to perform an individual risk assessment
together. All the data is included in the SAFETY ANALYSIS document.
6I USER MANUAL
DANGER SPOTS: Automatic doors might cause hazards like
crushing, shearing, hitting and drawing-in at the closing edges.
RESIDUAL RISK: Depending on the structural conditions, the
prevailing door version and the available safety equipment,
residual risks such as crushing and hitting (with a limited force)
cannot be excluded.
A – main closing edge
B– secondary closing edge
Danger spots

TECHNICAL DATA
7 I USER MANUAL
Technical data
Rated voltage
Movement speed of the sliding leaf/leaves
Rated power
IP protection class
Power source protection (F1)
Normal operating temperature
Permitted maximum relative humidity
The lifespan of the product
In-built glass for profiles PR 4
In-built glass for profiles PR 5
DOORSON aluminium profiles
230V 50/60Hz
max. 0.7m/s – depends on the weight of the leaves
300W
IP54
6,3A–slow
-20°C do 50°C
90%
15 years or at least 1,000,000 cycles
glued 4+4 or 5+5 ESG 8 or 10mm
insulated 3+3-9d-3+3, 6k-9d-6k, 5k-9d-5k or 5k-12d-5k
PR4 family – for a single safety glazing
PR5 family – for an isolation safety glazing
MAXIMUM DOOR DIMENSIONS AND WEIGHTS
Maximum dimensions and weights
The clear opening width extends from 800 to 3000 mm and the height is up to 3000 mm.
Prescribed maximum weight is 2 x 125 kg for a double leaf door, or 1 x 250 kg for a single leaf
door.

PRODUCT LINE 300
8 I USER MANUAL
Door types
TYPE
300 THALES
300
300 r
300 T r
300 P
300 P r
300 SC
300 SC r
standard door
standard door
standard door - redundant
telescopic door - redundant
prismatic door
prismatic door - redundant
semi curved door
semi curved door - redundant
300 C r curved door - redundant
300 F fire door without break-out system
DRIVE DESCRIPTION
standard
standard
standard redundant
mechanical redundant
300 EF fire door with break-out systemmechanical redundant
300 A door with break-out system
300 C curved door
300 T telescopic doorstandard
standard redundant
standard redundant
standard redundant
standard redundant
standard
standard
standard
standard
DRIVE
standard
standard
redundant
mechanical
redundant
BU3 slim
EL5
EC4
M
230V box
M r
BU3 slim
EL5
EC4 r
M
230V box
EL5
EC4 f
M
230V box
CONTENT
pulley
battery unit
electric lock
door controller
main motor
230V box
redundant motor
battery unit
electric lock
door controller
main motor
230V box
pulley
electric lock
door controller
main motor
230V box
actuators
mechanical redundant unit

PRODUCT LINE 300
9I USER MANUAL
Door types
Automatic sliding doors product line 300 are made according to the latest technologies and in compliance
with current technical regulations. Doors have to be installed according to the installation manual.
Note the next points that the doors will function properly and with the prescribed safety:
safety sensors have to be clean;
do not leave any obstructions or objects near automatic doors which could hinder the
functioning of the sensors within their operation area;
do not allow unauthorized entry into the drive system. Allow repairs and maintenance only
to professionally trained services;
use the system according to the user manual otherwise safety of people is at risk;
unauthorized interference with the system, its operation, removal of parts (safety sensors
for example) is not permitted;
the operator has to monitor the operating conditions and functioning of the system
occasionally and take care of system maintenance;
the power supply should not be manually switched off overnight (manually switch off
the power supply and batteries only if the door will not be used for several weeks);
do not allow power supply to be switched off for more than one week otherwise the
battery unit has to be replaced at door re-use.
SAFETY RECOMMENDATIONS
standard
standard redundant
mechanical redundant

DOOR OPERATION
10 I USER MANUAL
Ensure that mode selector COM20 is used on doors for escape routes and emergency exits
and is protected with an access code or a key, so the changes can only be made by authorized
personnel.
MODE SELECTION
Modes of operation
SYMBOL
CLOSED
OPEN
AUTOMATIC SUMMER
AUTOMATIC WINTER
EXIT SUMMER
EXIT WINTER
STOP
door closes and locks
door opens and remains open
door operation in automatic mode
door operation in automatic mode - reduced opening
door opens only with exit sensor
door opens only with exit sensor - reduced opening
door stops, can be moved manually
The operating mode of automatic sliding doors product line 300 are chosen with the mode selectors
COM20, COM21 or with additional devices via additional entries on the EC4 door controller.
MODE OPERATION
STOP
REDUNDANCY
TESTING
X
X
X
X
X
Ensure that mode selector COM20 is only activated when there are no other persons in the
room.

DOOR OPERATION
11 I USER MANUAL
Code for unlocking COM20 is “1239”. It is possible to change it.
COM20
COM20 is the most advanced mode selector for automatic sliding doors product line 300. The touch screen
serves to change the operating mode, adjust system settings and show warnings and errors
“in words“, not in LED codes.
Advanced mode selector COM20
WAKE BUTTON
 
 
 
 
 
COM21
COM21 is the basic mode selector for automatic sliding doors product line 300. The button serves to
change the operating mode with a simple turn. It shows warnings and errors in LED codes and has a WAKE
BUTTON.
Basic mode selector COM21
1LOCK
2OPEN
3AUTOMATIC SUMMER
4AUTOMATIC WINTER
5EXIT SUMMER
6STOP
7WAKE BUTTON

 
 
 
 
8ERROR – WARNING INDICATOR

COM21 has priority if the both (COM20 and COM21) are used.
1
2
3 4
5
6
7
8

DOOR OPERATION
12 I USER MANUAL
ADDITIONAL ENTRIES
Additional entries are sorted by the following priorities (from highest to lowest): STOP, LOCK, OPEN,
AUTO SUMMER, AUTO WINTER, EXIT SUMMER. If several additional entries are activated, the system
switches to the operating mode with the highest priority.
IN CASE OF POWER FAILURE
COM21 is connected to additional entries. In case several additional entries are active, the
system will use the one with the highest priority.
Connection on door controller
X8-1
X8-2
X8-3
X8-4
X8-6
X8-7
NO contact
NO contact
NO contact
NC or NO contact
LOCK NO contact
OPEN
AUTO SUMMER
AUTO WINTER
X8-5 NO contact
EXIT SUMMER
GROUND
STOP
Automatic sliding doors product line 300 can be equipped with a battery support in case of power supply
shortage due to a power cut in the electric power network. In such a case the LED diode LED1 in the EC4
door controller switches off, the doors open and remain still in open position after the power failure. The
system automatically switches off when the battery voltage drops to a certain limit.
The system can be re-activated by holding the WAKE BUTTON on the mode selector for 1 second or
triggering the input “open once” (X7-1) on the door controller EC4. The operating mode can be changed
after the system is re-activated by the above-described procedure. The system will automatically shut
down again if the main power supply stays off-line. The battery unit can be depleted in the case that main
power supply failure lasts longer. The system automatically switches to the main power supply source
when the main power supply re-establishes. In operation mode “CLOSED” the doors will close, even if
there is no electric power network.
The battery unit can be stored or stay DISCONNECTED from door controller for a maximum of
6 months, otherwise it needs to be replaced.
If the doors are not working for more than 1 week, the batteries need to be disconnected from
door controller.

DOOR OPERATION
13 I USER MANUAL
EXIT AND ENTRANCE INTO THE BUILDING
The following exit or entrance procedures can be used if automatic sliding doors product line 300 are
installed at the entrance of a building, which is also the only entrance:
1. EXIT from the building:
a) “EXIT SUMMER” or “EXIT WINTER” operating mode: The doors will normally open
at the exit with exit sensor.
b) “LOCK” operating mode: The function “SINGLE EXIT” must be first enabled in the
system settings to allow one time exit from the building. The doors will open once
by activating the exit sensor for 120 seconds. After this time or with the activated
exit sensor, exit from the building via the sensor will no longer be possible.
2. ENTRANCE into the building in “CLOSED”, “EXIT SUMMER” or “EXIT WINTER” operating
mode:
Entry into the building with the entry sensor is not possible. Install an additional switching
mechanism (card reader or other access control) connected to the input “open once” (X7-1)
on the door controller.
The energy save system shuts down the main power supply in the operating mode »CLOSED«, »OPEN«
and »STOP« and stays on battery power supply with reduced power consumption (less than 0.5 W).
The door leaves can be manually moved if the system is not equipped with the EL5 electric lock. Push the
WAKE BUTTON to wake up the doors from the energy save mode and then change the operating mode
into the preferred position. The system will shut down automatically again if the operating mode stays in
»CLOSED«, »OPEN« and »STOP« position.
Redundancy testing, door may open!
ENERGY SAVE

DOOR OPERATION
14 I USER MANUAL
REDUNDANCY TESTING
The redundancy system prevents the doors to stay in closed position if the door control system ceases to
operate (hardware/software fault). In this case the door opens and remains open. Such functionality
prevents people from staying trapped in the room/building.
Such safety functionality is needed if the doors are installed on escape routes!
The redundancy system is tested every twelve hours in mode EXIT or AUTO. The door opens once and
closes again in the test procedure. The drive electric parts are tested in this test (door controller EC4 r,
primary motor, battery unit, secondary motor). The door opens and remains open if the redundancy test
fails.
In CLOSED and STOP operating mode redundancy system is disabled!
Remember that the room/building is not LOCKED in EXIT operating mode if the door is
equipped with the redundancy system.

FIRE SIGNAL
15 I USER MANUAL
Automatic sliding doors product line 300 can be connected to a fire central, however, the systems
300 THALES r, 300 r, 300 C r, 300 T r, 300 P r, 300 SC r, 300 A, 300 F and 300 EF MUST be connected to
the fire central if it exists. If the mode selector is not in the »CLOSED« position, the doors will OPEN when
the fire signal is triggered, except for systems 300 F and 300 EF, they will close the doors. The door
controller can be connected to the fire central via X7 contact.
THE FIRE SIGNAL HAS THE HIGHEST PRIORITY!
Door controller EC4 and fire central connection

16 I USER MANUAL
Interfering in the inside of the drive while it is still under voltage is forbidden due to danger of
physical injuries that can be caused by the moving parts in the drive area.
Electric lock EL5
The electric lock EL5 locks the door leaf/leaves. Door is locked mechanically when the red handle on the
electric lock EL5 is in the LOCK position. For unlocking the red handle on the electric lock EL5 has to be
moved to the UNLOCK position. It is possible to change the LOCK or UNLOCK position of the electric lock
EL5 manually by system failure. The electric lock EL5 can be accessed by opening the cover of the drive.
The lock can also be unlocked electrically by pressing the WAKE UP BUTTON .
ELECTRIC LOCK EL5

FIRST STARTUP
17 I USER MANUAL
The following steps must be carried out before the first start-up:
1. The power supply plug must be pulled out;
2. The sliding leaf/leaves must be half open;
3. Check if the installation is in accordance with the installation manual;
4. All the mechanical safety elements and locking elements have to be unblocked and ensure
an uninterrupted initialization;
5. Switch on the system by plugging the power supply plug into door controller EC4;
6. Connect the battery unit BU3 with connector X4 on the door controller EC4 if the door
system comprises of a battery unit;
7. Switch the mode selector to the “AUTOMATIC-SUMMER” position;
8. The sliding leaf/leaves will slowly close;
9. The system will save the position CLOSED when the doors are closed (at the damper limit
in a one leaf door or when the leaves lean against each other in double leaf doors).
10. The doors will then slowly move to an open position and the system will save the position
OPEN at the damper limit;
11. The system initialization is complete.
The cable installation for the power supply and connection to the door system may be carried
out only by a specially trained person and according to current regulations. The door
construction must be additionally grounded in the case that the automatic doors are installed
on a steel construction.
Power supply will be necessary for at least 24 hours from the first system start-up to fully
charge the battery unit BU3.
Please unplug the battery unit BU3 from door controller EC4 (X4 connector) if the doors are not
used for one week or more. The battery can be stored for a maximum of half a year
DISCONNECTED.

18 I USER MANUAL
During the building’s opening hours when the doors are in operation the sliding door must be
unbolted, so that in the case of panic conditions the doors can be wide open by force. A GREEN
button must be visible on the bolt of the sliding doors.
TYPE 300 A
When the “CLOSE” mode is selected the door will lock electrically. The sliding leaves must bolt, so that we
can block the break-out function and thus disable the options of dislocation leaves from outside.
Locked doors
The sliding leaves must be bolted. A RED button must be visible on the bolt of the sliding
NORMAL OPERATION OF 300 A

TYPE 300 A
19 I USER MANUAL
POSSIBILITY OF ENLARGING THE PASSAGE OPENING
When the fixed and sliding wings are fully open and pushed together the passage opening is almost twice
the size.
ACTIVATION OF THE BREAK-OUT FUNCTION
The sliding and fixed wings open out in the direction of the emergency exit by physical force regardless of
the position of the sliding wings. If the sliding wings are in movement at the moment they immediately
stop.
Activating the break-out function on CLOSED doors is only possible when the sliding doors are
UNBOLTED. A GREEN button must be visible on the bolt of the sliding doors.
Unlocked doors

20 I USER MANUAL
INTENDED USE OF 300 F
DOORS WITH FIRE RESISTANCE, WITHOUT BREAK-OUT FUNCTION
The 300 F projected automatic sliding fire doors for non-escape routes are designed to be installed
between the fire sectors as separating walls and should not be installed in passages with escape routes,
because in the CASE OF EMERGENCY, i.e. fire alarm actuation, network supply failure or defective
automatic door system, passing through the door is impossible. In the event of fire, the door closes
unconditionally and represents a barrier, preventing the fire to spcread from one sector to another.
INTENDED USE OF 300 EF
DOORS FOR ESCAPE ROUTES AND EMERGENCY EXITS WITH BREAK-OUT FUNCTION AND
FIRE RESISTANCE
The 300 EF projected automatic sliding fire doors for escape routes and emergency exits are designed to
be installed at the borders of fire sectors and at the passages of escape routes. Under normal conditions,
the door acts like a sliding door, whereas in case of emergency, the sliding leaves will close unconditionally
using the stored potential energy and the integrated swinging leaves will unbolt, enabling easy escape. The
swinging leaves have an integrated special equipment and fittings which provide for an emergency exit.
TYPE 300 F AND 300 EF