Dorner 39M Series User manual

851-558 Rev. B
Installation, Maintenance
& Parts Manua
l
Fixed and Adjustable Height Stands
Table of Contents
WARNINGS – General Safety 2. . . . . . . . . . . . . . . . .
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Description 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Installation Sequence 4. . . . . . . . . .
Assembly
Stands Shipped Partially Assembled 4. . . . . . . . . . . .
Required Tools 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stands Shipped Fully Assembled 7. . . . . . . . . . . . . .
Required Tools 7. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Fine Adjustment Kit 8. . . . . . . . . . . . . . . .
Required Tools 8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Caster Kit 9. . . . . . . . . . . . . . . . . . . . . . . .
Required Tools 9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance and Adjustment 10. . . . . . .
Stand Height Adjustment 10. . . . . . . . . . . . . . . . . . . .
Height Adjustment for Fixed and Adjustable
Height Stands 10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Tools 10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Height Adjustment for Fixed and Adjustable
Height Stands with Fine Adjustment Kit 11. . . . . . .
Required Tools 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Conveyor Angle Adjustment 12. . . . . . . . . . . . . . .
Required Tools 12. . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Parts 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Policy 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 2Dorner Mfg. Corp.
The safety alert symbol, black triangle with white
exclamation, is used to alert you to potential
personal injury hazards.
Ç
Ç
Ç
Ç
Climbing, sitting, walking or
riding on conveyor will
cause severe injury.
KEEP OFF CONVEYORS.
DANGER
Ç
DANGER
DO NOT OPERATE
CONVEYORS IN AN
EXPLOSIVE ENVIRONMENT.
Ç
Supports marked with this
symbol must be anchored to
the floor. Supports not
anchored to floor will tip,
causing severe injury or
death.
SUPPORT MUST BE
ANCHORED TO FLOOR.
DANGER
Ç
Exposed moving parts can
cause severe injury.
LOCK OUT POWER before
removing guards or
performing maintenance.
Ç
Loosening stand height or
angle adjustment screws
may cause conveyor
sections to drop down,
causing severe injury.
SUPPORT CONVEYOR
SECTIONS PRIOR TO
LOOSENING STAND HEIGHT
OR ANGLE ADJUSTMENT
SCREWS.
Ç
Ç
Dorner cannot control the
physical installation and
application of conveyors.
Taking protective measures
is the responsibility of the
user.
When conveyors are used in
conjunction with other equip-
ment or as part of a multiple
conveyor system, CHECK
FOR POTENTIAL PINCH
POINTS and other mechani-
cal hazards before system
start-up.
Introduction
IMPORTANT: Some illustrations may show guards
removed. Do NOT operate equipment without guards.
Upon receipt of shipment:
DCompare shipment with packing slip. Contact factory
regarding discrepancies.
DInspect packages for shipping damage. Contact carrier
regarding damage.
DAccessories may be shipped loose. See accessory in-
structions for installation.
Dorner’s Limited Warranty applies.
Dorner reserves the right to make changes at any time
without notice or obligation.
Warnings - General Safety

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 3851-558 Rev. B
Refer to Figure 1 for typical stand components.
A Support Stand
B Stand Mounting Bracket (with conveyor)
C Boot
D Height Adjustment Point
E Angle Adjustment Point
F Optional Casters
G Optional Diagonal Brace
Typical Components
A
B
C
D
E
F
Figure 1
G
Specifications
Fixed and Adjustable Stand Models
Language Code
M = U.S. English
Width
02” to 48”
Min Height
From Floor to Top Bracket
Max Height
From Floor to Top Bracket
H Style Stand
39 M TT WW – HH HH F A
Stand Type
FH = Fixed Height
AH = Adjustable Height
FT = Tall, Fixed Height
AT = Tall, Adjustable Height
Floor Interface
F = Fixed Foot Pad
C = Total Lock Swivel Caster
Assembly
P = Partially Assembled
A = Fully Asembled
Example: 39MFH12–3248FP
Fixed height, H style stand for a 12”
wide conveyor with a min height of 32”
and a max height of 48” with fixed foot
pads. It comes partially assembled and
has U.S. English documentation.
WW
HH
Product Description

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 4Dorner Mfg. Corp.
Ç
Supports marked with this
symbol must be anchored to
the floor. Supports not
anchored to floor will tip,
causing severe injury or
death.
SUPPORTS MUST BE
ANCHORED TO FLOOR.
DANGER
Ç
Ç
Exposed moving parts can
cause severe injury.
LOCK OUT POWER before
removing guards or
performing maintenance.
Recommended Installation Sequence (see
Table of Contents for page numbers)
DAssemble stand(s), if required
DAttach stand(s) to conveyor (see Conveyor Installa-
tion, Maintenance & Parts Manual)
DAttach optional diagonal bracing (see Diagonal
Brace Kit Manual)
DAdjust stand height and level (see Adjustment sec-
tion, page 10)
Assembly
Stands Shipped Partially Assembled
Required Tools
D6 mm Hex Key Wrench
1.Typical components (Figure 2).
Typical Components
H Boots/Foot Plate Assembly (2x)
I Hardware Pack, Standard Stand
J Conveyor Mounting Bracket(s)
(2 possible configurations)
K Vertical Stand Legs (2x)
L Hardware Pack, Crossmember
(quantity as required)
M Crossmembers (quantity as required)
N U–nuts (2x)
Figure 2
K
H
M
N
J
LI
or
2.Open standard stand hardware pack (I of Figure 2).
NOTE: Stand legs (K of Figure 3) are equipped with a
height sticker (P). Assemble stand legs with the sticker
on the outside and the red warning area (O) at the bot-
tom of the legs.
Shown assembled. See steps 7 and 8 for boot as-
sembly.
Figure 3
K
P
O
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 5851-558 Rev. B
3.On the side opposite height sticker (P of Figure 3)
install one (1) hex nut (Q of Figure 4) into each inside
stand leg (K) t–slot.
Figure 4
QK
4.Attach crossmember (M of Figure 5) to stand leg (K)
with button screws (R). Do not tighten.
Figure 5
RK
M
5.Repeat step 4 for opposite stand leg. Make sure to
locate the red warning area (P of Figure 3) on the
same ends of stand legs (K of Figure 5).
Ç
Failure to secure screws (R
of Figure 6) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
6.Upright stand and locate and space crossmember(s)
(M of Figure 6) evenly along stand leg (K). Tighten
crossmember button screws (R) to 150 in–lb (17
N–m).
Figure 6
R
M
K
7.On the end with red warning area (O of Figure 7)
install one (1) hex nut (Q) into each outside stand leg
(K) t–slot.
Figure 7
Q
KO
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 6Dorner Mfg. Corp.
Ç
Failure to secure screws (R
of Figure 8) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
8.Slide boot (H of Figure 8) onto stand leg (K). Align
hex nuts (Q) and boot holes and attach boot with
button screws (R). Tighten button screws to 150
in–lb (17 N–m). Repeat for opposite leg.
IMPORTANT: Red warning area (O of Figure 8 must be
under boot (H) after assembly.
Figure 8
H
Q K
R
O
9.Install u–nuts (N of Figure 9) into outer t–slots of
stand legs (K).
Figure 9
N
K
N
Ç
Failure to secure screws (S
of Figure 10) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (S)
AFTER ADJUSTMENT.
10.Align conveyor mounting bracket (J of Figure 10)
with u–nuts. Attach flange socket screws (S)
through bracket and into u–nuts. Tighten flange
socket screws (S) to 150 in–lb (17 N–m).
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 7851-558 Rev. B
Figure 10
J
S
11.For leveling and height adjustment see page 9.
Stands Shipped Fully Assembled
Required Tools
D6 mm Hex Key Wrench
1.Typical components (Figure 11).
Typical Components
T Stand Assembly
H Boot Assembly (2x)
Figure 11
T
HH
2.Loosen (2) hex nuts Q of Figure 12) located on boot
assembly (H).
Figure 12
H
Q
Ç
Failure to secure screws (R
of Figure 13) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
3.Slide (2) hex nuts (Q of Figure 13) along with boot
assembly (H) into outer slots of stand assembly (T).
Tighten button screw (R) to 150 in–lb (17 N–m).
Figure 13
T
Q
R
H
4.Repeat steps 2 and 3 for opposite stand leg.
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 8Dorner Mfg. Corp.
Optional Fine Adjustment Kit
Required Tools
D6 mm Hex Key Wrench
Typical Components
U Adjustment Kit (2x)
Figure 14
U
1.Loosen stand boot screws (R of Figure 15).
Figure 15
R
2.Raise stand leg (K of Figure 16) until it is above fine
adjustment bolt assembly (U). Insert fine adjustment
kit (U) into stand leg (K).
Figure 16
U
K
3.Lower stand leg (K of Figure 17) until stand edge (V)
is resting on lower nut (W) flange.
Figure 17
V
K
W
Ç
Failure to secure screws (R
of Figure 15) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
4.Tighten stand button screws (R of Figure 15) to 150
in–lb (17 N–m).
5.Repeat steps 1 through 4 for opposite stand leg.
6.For leveling and height adjustment see page 9.
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 9851-558 Rev. B
Optional Caster Kit
Required Tools
D17 mm Open End Wrench
Typical Components
X Caster (2x)
Y Carriage Bolt (2x)
Z Nut (2x)
Figure 18
X
YZ
1.Install carriage bolt (Y of Figure 19) into stand boot
base plate (AA).
Figure 19
Y AA
2.Install caster (X of Figure 20) over carriage bolt (Y
of Figure 19).
3.Place nut (Z of Figure 20) on carriage bolt. Tighten
nut to 177 in–lb (20 N–m).
Figure 20
Z
X
4.Repeat steps 1 through 3 for opposite leg.
Installation

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 10 Dorner Mfg. Corp.
Stand Height Adjustment
Height Adjustment for Fixed and Adjustable
Height Stands
Required Tools
D6 mm Hex Key Wrench
Ç
Ç
Exposed moving parts can
cause severe injury.
LOCK OUT POWER before
removing guards or
performing maintenance.
Ç
Loosening stand height or
angle adjustment screws
may cause conveyor
sections to drop down,
causing severe injury.
SUPPORT CONVEYOR
SECTIONS PRIOR TO
LOOSENING STAND HEIGHT
OR ANGLE ADJUSTMENT
SCREWS.
1.Using a support (AB of Figure 21), raise conveyor
and stand off the floor.
Figure 21
AB
K
R
AC
2.Loosen button screws (R).
3.Raise or lower stand leg (K) to the required height.
Level stand from side to side using a level (AC).
Ç
Ç
Failure to secure screws (R
of Figure 21) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
4.Tighten button screws (R) to 150 in–lb (17 N–m).
5.Repeat steps 2 through 4 on opposite stand leg.
Preventive Maintenance and Adjustment

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 11 851-558 Rev. B
Height Adjustment for Fixed and Adjustable
Height Stands with Fine Adjustment Kit
Required Tools
D6 mm Hex Key Wrench
D13 mm Open End Wrench
Ç
Exposed moving parts can
cause severe injury.
LOCK OUT POWER before
removing guards or
performing maintenance.
Ç
Ç
Loosening stand height or
angle adjustment screws
may cause conveyor
sections to drop down,
causing severe injury.
SUPPORT CONVEYOR
SECTIONS PRIOR TO
LOOSENING STAND HEIGHT
OR ANGLE ADJUSTMENT
SCREWS.
1.Loosen boot screws (R of Figure 21).
2.Turn kit bolt (AD of Figure 22) to required height.
Figure 22
AD
Ç
Failure to secure screws (R
of Figure 21) may cause
conveyor sections to drop
down causing severe injury.
TIGHTEN SCREWS (R)
AFTER ADJUSTMENT.
3.Tighten button screws (R of Figure 21) to 150 in–lb
(17 N–m).
4.Repeat steps 1 through 3 on opposite Adjustment
Kit.
Preventive Maintenance and Adjustment

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 12 Dorner Mfg. Corp.
Conveyor Angle Adjustment
Required Tools
D6 mm Hex Key Wrench
Ç
Loosening stand height or
angle adjustment screws
may cause conveyor
sections to drop down,
causing severe injury.
SUPPORT CONVEYOR
SECTIONS PRIOR TO
LOOSENING STAND HEIGHT
OR ANGLE ADJUSTMENT
SCREWS.
NOTE: To rotate stand top plate, screws (S of Figure
23) may need to be re-located to other t–slots (AE).
1.Loosen flange socket screws (S of Figure 23) on both
sides of stand.
Figure 23
S
AE
2.Adjust conveyor to desired angle.
Ç
Failure to secure screws (S
of Figure 23) may cause
conveyor sections to drop
down, causing severe injury.
TIGHTEN SCREWS (S)
AFTER ADJUSTMENT.
3.Secure flange socket screws (S of Figure 23) to 24
ft-lb (18 Nm).
4.If conveyor is equipped with diagonal bracing (AH of
Figure 24), socket screw (AI) must be loosened to
adjust conveyor angle. Secure screw to 100 in–lb (11
N–m) after adjustment.
Figure 24
AH
AI
Preventive Maintenance and Adjustment

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 13 851-558 Rev. B
NOTE: For replacement parts other than those
shown on this page, contact an authorized Dorner
Service Center or the factory.
Fixed Height Stand w/Feet or Casters
2
11
10
9
1
15
3
7
13
14
12
4
6
5
8
9
or
or
or
1
Item Part Number Description
1 202148 Bracket, Mtg. 12” (305mm) and under
(1x)
200697 Bracket, Mtg. 14” (357mm) and over
(2x)
2 920883M Scr, Flange, Socket M8–1.25x16MM
3See Leg Table Leg, Stand
4 911016M Scr, Bttn, Metric M10–1.50x16MM
5 710031–00816 Boot, Stand Leg
6 807–1286 Bolt, Carriage M10–1.5x25MM
7 710005 Plate, Caster Mtg. Stand
8 807–640 Caster, 4”
9 991001M Nut, Hex, Full M10–1.50
10 960897M Scr, Hex Hd, Metric M8–1.25x30MM
11 See Cross-
member Table Crossmember
12 710004 Foot, Stand, Floor Mtg
13 710006 Plate, End, Crossmember Stand
14 200801M Nut, Quad, M8–1.25
15 708180P Scr, Sock, Metric M6–1.00x25MM
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 14 Dorner Mfg. Corp.
Item 3: Leg Table (With Foot)
Leg Height Range Leg Part Number
15”–19” (381mm–483mm) 710211–01263
16”–20” (406mm–508mm) 710211–01363
17”–21” (432mm–533mm) 710211–01463
18”–22” (457mm–559mm) 710211–01563
19”–23“ (483mm–584mm) 710211–01663
20”–24” (508mm–610mm) 710211–01763
21”–25” (533mm–635mm) 710211–01863
22”–26” (559mm–660mm) 710211–01963
23”–27” (584mm–686mm) 710211–02063
24”–28” (610mm–711mm) 710211–02163
25”–29” (635mm–737mm) 710211–02263
26”–30” (660mm–762mm) 710211–02363
27”–31” (686mm–787mm) 710211–02463
28”–32” (711mm–813mm) 710211–02563
29”–33” (737mm–838mm) 710211–02663
30”–34“ (762mm–864mm) 710211–02763
31”–35” (787mm–889mm) 710211–02863
32”–36” (813mm–914mm) 710211–02963
33”–37” (838mm–940mm) 710211–03063
34”–38” (864mm–965mm) 710211–03163
35”–39” (889mm–991mm) 710211–03263
36”–40” (914mm–1016mm) 710211–03363
37”–41” (940mm–1041mm) 710211–03463
38”–42” (965mm–1067mm) 710211–03563
39”–43” (991mm–1092mm) 710211–03663
40”–44” (1016mm–1118mm) 710211–03763
41”–45“ (1041mm–1143mm) 710211–03863
42”–46” (1067mm–1168mm) 710211–03963
43”–47” (1092mm–1194mm) 710211–04063
44”–48” (1118mm–1219mm) 710211–04163
45”–49” (1143mm–1245mm) 710211–04263
46”–50” (1168mm–1270mm) 710211–04363
47”–51” (1194mm–1295mm) 710211–04463
48”–52” (1219mm–1321mm) 710211–04563
49”–53” (1245mm–1346mm) 710211–04663
50”–54” (1270mm–1372mm) 710211–04763
51”–55” (1295mm–1397mm) 710211–04863
52”–56“ (1321mm–1422mm) 710211–04963
53”–57” (1346mm–1448mm) 710211–05063
54”–58” (1372mm–1473mm) 710211–05163
Leg Height Range Leg Part Number
55”–59” (1397mm–1499mm) 710211–05263
56”–60” (1422mm–1524mm) 710211–05363
57”–61” (1448mm–1549mm) 710211–05463
58”–62” (1473mm–1575mm) 710211–05563
59”–63” (1499mm–1600mm) 710211–05663
60”–64” (1524mm–1626mm) 710211–05763
61”–65” (1549mm–1651mm) 710211–05863
62”–66” (1575mm–1676mm) 710211–05963
63”–67” (1600mm–1702mm) 710211–06063
64”–68” (1626mm–1727mm) 710211–06163
65”–69” (1651mm–1753mm) 710211–06263
66”–70” (1676mm–1778mm) 710211–06363
67”–71” (1702mm–1803mm) 710211–06463
68”–72” (1727mm–1829mm) 710211–06563
69”–73“ (1753mm–1854mm) 710211–06663
70”–74” (1778mm–1880mm) 710211–06763
71”–75” (1803mm–1905mm) 710211–06863
72”–76” (1829mm–1930mm) 710211–06963
73”–77” (1854mm–1956mm) 710211–07063
74”–78” (1880mm–1981mm) 710211–07163
75”–79” (1905mm–2007mm) 710211–07263
76”–80” (1930mm–2032mm) 710211–07363
77”–81” (1956mm–2057mm) 710211–07463
78”–82” (1981mm–2083mm) 710211–07563
79”–83” (2007mm–2108mm) 710211–07663
80”–84“ (2032mm–2134mm) 710211–07763
81”–85” (2057mm–2159mm) 710211–07863
82”–86” (2083mm–2184mm) 710211–07963
83”–87” (2108mm–2210mm) 710211–08063
84”–88” (2134mm–2235mm) 710211–08163
85”–89” (2159mm–2261mm) 710211–08263
86”–90” (2184mm–2286mm) 710211–08363
87”–91” (2210mm–2311mm) 710211–08463
88”–92” (2235mm–2337mm) 710211–08563
89”–93” (2261mm–2362mm) 710211–08663
90”–94” (2286mm–2388mm) 710211–08763
91”–95“ (2311mm–2413mm) 710211–08863
92”–96” (2337mm–2438mm) 710211–08963
93”–97” (2362mm–2464mm) 710211–09063
94”–98” (2388mm–2489mm) 710211–09163
95”–99” (2413mm–2515mm) 710211–09263
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 15 851-558 Rev. B
Item 3: Leg Table (With Caster)
Leg Height Range Leg Part Number
20”–24” (508mm–610mm) 710211–01263
21”–25” (533mm–635mm) 710211–01363
22”–26” (559mm–660mm) 710211–01463
23”–27” (584mm–686mm) 710211–01563
24”–28” (610mm–711mm) 710211–01663
25”–29” (635mm–737mm) 710211–01763
26”–30” (660mm–762mm) 710211–01863
27”–31” (686mm–787mm) 710211–01963
28”–32” (711mm–813mm) 710211–02063
29”–33” (737mm–838mm) 710211–02163
30”–34“ (762mm–864mm) 710211–02263
31”–35” (787mm–889mm) 710211–02363
32”–36” (813mm–914mm) 710211–02463
33”–37” (838mm–940mm) 710211–02563
34”–38” (864mm–965mm) 710211–02663
35”–39” (889mm–991mm) 710211–02763
36”–40” (914mm–1016mm) 710211–02863
37”–41” (940mm–1041mm) 710211–02963
38”–42” (965mm–1067mm) 710211–03063
39”–43” (991mm–1092mm) 710211–03163
40”–44” (1016mm–1118mm) 710211–03263
41”–45“ (1041mm–1143mm) 710211–03363
42”–46” (1067mm–1168mm) 710211–03463
43”–47” (1092mm–1194mm) 710211–03563
44”–48” (1118mm–1219mm) 710211–03663
45”–49” (1143mm–1245mm) 710211–03763
46”–50” (1168mm–1270mm) 710211–03863
47”–51” (1194mm–1295mm) 710211–03963
48”–52” (1219mm–1321mm) 710211–04063
49”–53” (1245mm–1346mm) 710211–04163
50”–54” (1270mm–1372mm) 710211–04263
51”–55” (1295mm–1397mm) 710211–04363
52”–56“ (1321mm–1422mm) 710211–04463
53”–57” (1346mm–1448mm) 710211–04563
54”–58” (1372mm–1473mm) 710211–04663
55”–59” (1397mm–1499mm) 710211–04763
56”–60” (1422mm–1524mm) 710211–04863
57”–61” (1448mm–1549mm) 710211–04963
58”–62” (1473mm–1575mm) 710211–05063
59”–63” (1499mm–1600mm) 710211–05163
60”–64” (1524mm–1626mm) 710211–05263
61”–65” (1549mm–1651mm) 710211–05363
62”–66” (1575mm–1676mm) 710211–05463
63”–67” (1600mm–1702mm) 710211–05563
64”–68” (1626mm–1727mm) 710211–05663
65”–69” (1651mm–1753mm) 710211–05763
66”–70” (1676mm–1778mm) 710211–05863
67”–71” (1702mm–1803mm) 710211–05963
Item 11: Crossmember Table
Stand Width Crossmember Part Number
2”–12” (51mm–304mm) 710210–00976
14” (357mm) 710210–01176
16” (406mm 710210–01376
18” (457mm) 710210–01576
20” (508mm) 710210–01776
22” (559mm) 710210–01976
24” (610mm) 710210–02176
26” (661mm) 710210–02376
28” (711mm) 710210–02576
30” (762mm) 710210–02776
32” (813mm) 710210–02976
34” (864mm) 710210–03176
36” (915mm) 710210–03376
38” (966mm) 710210–03576
40” (1016mm) 710210–03776
42” (1067mm) 710210–03976
44” (1118mm) 710210–04176
46” (1169mm) 710210–04376
48” (1220mm) 710210–04576
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 16 Dorner Mfg. Corp.
Adjustable Height Stand w/Feet or Casters
13
5
12
1
15
9
10
11
4
14
3
8
7
6
9
or
or
or
2
1
Item Part Number Description
1 202148 Bracket, Mtg. 12” (305mm) and under
(1x)
200697 Bracket, Mtg. 14” (357mm) and over
(2x)
2 920883M Scr, Flange, Socket M8–1.25x16MM
3See Leg/Boot
Table Leg, Stand
4 911016M Scr, Bttn, Metric M10–1.50x16MM
5See Leg/Boot
Table Boot, Stand Leg
6 807–1286 Bolt, Carriage M10–1.5x25MM
7 710005 Plate, Caster Mtg. Stand
8 807–640 Caster, 4”
9 991001M Nut, Hex, Full M10–1.50
10 960896M Scr, Tri–Lobe, HD–Hex M8x25MM
11 See Cross-
member Table Crossmember
12 710004 Foot, Stand, Floor Mtg
13 710006 Plate, End, Crossmember Stand
14 200801M Nut, Quad, M8–1.25
15 708180P Scr, Sock, Metric M6–1.00x25MM
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 17 851-558 Rev. B
Items 3 and 5: Leg/Boot Table (With Foot)
Stand Height
Range Leg Part Number
(Item 3) Boot Part Number (Item 5)
12”–13”
(305mm–330mm) 710211–00963 710031–00516
13”–15”
(330mm–381mm) 710211–01063 710031–00616
14”–17”
(356mm–432mm) 710211–01163 710031–00716
16”–21”
(406mm–533mm) 710211–01363 710031–00916
19”–26”
(483mm–660mm) 710211–01663 710031–01116
24”–36”
(610mm–914mm) 710211–02163 710031–01616
30”–48”
(762mm–1219mm) 710211–02763 710031–02216
42”–60”
(1067mm–1524mm) 710211–03963 710031–02216
54”–72”
(1372mm–1829mm) 710211–05163 710031–02216
66”–84”
(1676mm–2134mm) 710211–06363 710031–02216
78”–96”
(1981mm–2438mm) 710211–07563 710031–02216
Items 3 and 5: Leg/Boot Table (With Caster)
Stand Height
Range Leg Part Number
(Item 3) Boot Part Number (Item 5)
17”–18”
(432mm–457mm) 710211–00963 710031–00516
18”–20”
(457mm–508mm) 710211–01063 710031–00616
19”–22”
(483mm–559mm) 710211–01163 710031–00716
21”–26”
(533mm–660mm) 710211–01363 710031–00916
24”–31”
(610mm–787mm) 710211–01663 710031–01116
29”–41”
(737mm–1041mm) 710211–02163 710031–01616
35”–53”
(889mm–1346mm) 710211–02763 710031–02216
47”–65”
(1194mm–1651mm) 710211–03963 710031–02216
59”–77”
(1499mm–1956mm) 710211–05163 710031–02216
71”–89”
(1803mm–2261mm) 710211–06363 710031–02216
81”–99”
(2057mm–2515mm) 710211–07363 710031–02216
Item 11: Crossmember Table
Stand Width Crossmember Number
2”–12”
(51mm–304mm) 710210–00976
14” (357mm) 710210–01176
16” (406mm 710210–01376
18” (457mm) 710210–01576
20” (508mm) 710210–01776
22” (559mm) 710210–01976
24” (610mm) 710210–02176
26” (661mm) 710210–02376
28” (711mm) 710210–02576
30” (762mm) 710210–02776
32” (813mm) 710210–02976
34” (864mm) 710210–03176
36” (915mm) 710210–03376
38” (966mm) 710210–03576
40” (1016mm) 710210–03776
42” (1067mm) 710210–03976
44” (1118mm) 710210–04176
46” (1169mm) 710210–04376
48” (1220mm) 710210–04576
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 18 Dorner Mfg. Corp.
Tall Stand with Feet or Casters
12
1
4
10
11
16
14
5
15 8
19
17
2
6
3
or
or
18
13
9
9
7
20
13
or
1
Item Part Number Description
1 202148 Brkt, Mtg, Stand/Conv 12”
200697 Bracket, Mtg. 14” (357mm) and over
(2x)
2See Inner Leg
Table Leg, Stand, Inner
3 710214–00621 Tie Tube, Stand
4 807–1289 Rivet, Tree, .22 Dia x .75 Long
5 710003 Label–Cover, Stand
6 710211–01663 Leg, Stand, Outer, Fixed Height
710031–02263 Leg, Stand, Outer, Adjustable Height
7 911016M Scr, Bttn, Metric M10–1.50x16mm
8 710004 Foot, Stand, Floor Mtg
9 960896M Scr, Tri–Lobe, Hd–Hex M8x25mm
10 961030M Bolt, Carriage M10–1.5x35mm
11 710005 Plate, Caster Mtg, Stand
12 807–640 Caster, 4”
13 991001M Nut, Hex, Full M10–1.50
14 710031–00616 Boot, Stand Leg, Fixed Height
710031–02216 Boot, Stand Leg, Adjustable Height
15 710006 Plate, End, Crossmember Stand
16 See Base
Crossmember
Table Crossmember, Stand Base
17 708180P Scr, sock, Metric M6–1.00x25mm
18 See Cross-
member Table Crossmember, Stand
19 200801M Nut, Quad, M8–1.25
20 920883M Scr, Flange, Socket M8–1.25x16mm
Service Parts

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
Dorner Mfg. Corp. 19 851-558 Rev. B
Item 2: Inner Leg Table (Fixed Height With Foot)
Stand Height Range Leg Part Number
41”–45” (1041mm–1143mm) 710211–03763
42”–46” (1067mm–1168mm) 710211–03863
43”–47” (1092mm–1194mm) 710211–03963
44”–48” (1118mm–1219mm) 710211–04063
45”–49” (1143mm–1245mm) 710211–04163
46”–50” (1168mm–1270mm) 710211–04263
47”–51” (1194mm–1295mm) 710211–04363
48”–52” (1219mm–1321mm) 710211–04463
49”–53” (1245mm–1346mm) 710211–04563
50”–54” (1270mm–1372mm) 710211–04663
51”–55” (1295mm–1397mm) 710211–04763
52”–56” (1321mm–1422mm) 710211–04863
53”–57” (1346mm–1448mm) 710211–04963
54”–58” (1372mm–1473mm) 710211–05063
55”–59” (1397mm–1499mm) 710211–05163
56”–60” (1422mm–1524mm) 710211–05263
57”–61” (1448mm–1549mm) 710211–05363
58”–62” (1473mm–1575mm) 710211–05463
59”–63” (1499mm–1600mm) 710211–05563
60”–64” (1524mm–1626mm) 710211–05663
61”–65” (1549mm–1651mm) 710211–05763
62”–66” (1575mm–1676mm) 710211–05863
63”–67” (1600mm–1702mm) 710211–05963
64”–68” (1626mm–1727mm) 710211–06063
65”–69” (1651mm–1753mm) 710211–06163
66”–70” (1676mm–1778mm) 710211–06263
67”–71” (1702mm–1803mm) 710211–06363
68”–72” (1727mm–1829mm) 710211–06463
69”–73” (1753mm–1854mm) 710211–06563
70”–74” (1778mm–1880mm) 710211–06663
71”–75” (1803mm–1905mm) 710211–06763
72”–76” (1829mm–1930mm) 710211–06863
73”–77” (1854mm–1956mm) 710211–06963
74”–78” (1880mm–1981mm) 710211–07063
75”–79” (1905mm–2007mm) 710211–07163
76”–80” (1930mm–2032mm) 710211–07263
77”–81” (1956mm–2057mm) 710211–07363
78”–82” (1981mm–2083mm) 710211–07463
79”–83” (2007mm–2108mm) 710211–07563
80”–84” (2032mm–2134mm) 710211–07663
81”–85” (2057mm–2159mm) 710211–07763
82”–86” (2083mm–2184mm) 710211–07863
83”–87” (2108mm–2210mm) 710211–07963
84”–88” (2134mm–2235mm) 710211–08063
85”–89” (2159mm–2261mm) 710211–08163
86”–90” (2184mm–2286mm) 710211–08263
87”–91” (2210mm–2311mm) 710211–08363
88”–92” (2235mm–2337mm) 710211–08463
89”–93” (2261mm–2362mm) 710211–08563
90”–94” (2286mm–2388mm) 710211–08663
91”–95” (2311mm–2413mm) 710211–08763
92”–96” (2337mm–2438mm) 710211–08863
93”–97” (2362mm–2464mm) 710211–08963
94”–98” (2388mm–2489mm) 710211–09063
95”–99” (2413mm–2515mm) 710211–09163

Fixed and Adjustable Height Stands Set-up, Operation & Maintenance Manual
851-558 Rev. B 20 Dorner Mfg. Corp.
Item 2: Inner Leg Table (Fixed Height With Caster)
Stand Height Range Leg Part Number
41”–45” (1041mm–1143mm) 710211–03263
42”–46” (1067mm–1168mm) 710211–03363
43”–47” (1092mm–1194mm) 710211–03463
44”–48” (1118mm–1219mm) 710211–03563
45”–49” (1143mm–1245mm) 710211–03663
46”–50” (1168mm–1270mm) 710211–03763
47”–51” (1194mm–1295mm) 710211–03863
48”–52” (1219mm–1321mm) 710211–03963
49”–53” (1245mm–1346mm) 710211–04063
50”–54” (1270mm–1372mm) 710211–04163
51”–55” (1295mm–1397mm) 710211–04263
52”–56” (1321mm–1422mm) 710211–04363
53”–57” (1346mm–1448mm) 710211–04463
54”–58” (1372mm–1473mm) 710211–04563
55”–59” (1397mm–1499mm) 710211–04663
56”–60” (1422mm–1524mm) 710211–04763
57”–61” (1448mm–1549mm) 710211–04863
58”–62” (1473mm–1575mm) 710211–04963
59”–63” (1499mm–1600mm) 710211–05063
60”–64” (1524mm–1626mm) 710211–05163
61”–65” (1549mm–1651mm) 710211–05263
62”–66” (1575mm–1676mm) 710211–05363
63”–67” (1600mm–1702mm) 710211–05463
64”–68” (1626mm–1727mm) 710211–05563
65”–69” (1651mm–1753mm) 710211–05663
66”–70” (1676mm–1778mm) 710211–05763
67”–71” (1702mm–1803mm) 710211–05863
68”–72” (1727mm–1829mm) 710211–05963
Item 2: Inner Leg Table (Adjustable Height With Foot)
Stand Height Range Leg Part Number
42”–60” (1067mm–1524mm) 710211–03763
54”–72” (1372mm–1829mm) 710211–04963
66”–84” (1676mm–2134mm) 710211–06163
78”–96” (1981mm–2438mm) 710211–07363
Item 2: Inner Leg Table (Adjustable Height With Caster)
Stand Height Range Leg Part Number
47”–65” (1194mm–1651mm) 710211–03763
59”–77” (1499mm–1956mm) 710211–04963
Item 16: Base Crossmember Table
Stand Width Crossmember Number
12” (305mm) 710215–02576*
14” (357mm) 710215–02776
16” (406mm 710215–02976
18” (457mm) 710215–03176
20” (508mm) 710215–03376
22” (559mm) 710215–03576
24” (610mm) 710215–03776
26” (661mm) 710215–03976
28” (711mm) 710215–04176
* Compatible with all conveyor widths of 12” (305mm) or less.
Item 18: Crossmember Table
Stand Width Crossmember Number
12” (305mm) 710210–00976*
14” (357mm) 710210–01176
16” (406mm 710210–01376
18” (457mm) 710210–01576
20” (508mm) 710210–01776
22” (559mm) 710210–01976
24” (610mm) 710210–02176
26” (661mm) 710210–02376
28” (711mm) 710210–02576
* Compatible with all conveyor widths of 12” (305mm) or less.
Service Parts