DTVS DSR2 User manual

13/18V
500mA Max.
LNB1IN LNB2IN
LNB1 OUT LNB2OUT
UPGRADE ONLY TV ANT IN
SPDIF L-AUDIO-R VIDEO
L
R
AC 110-240V~
50/60Hz
30W Max.
OFF
ON
POWER
Y Cb Cr
TO TV
HDMI ETHERNET Z1082
Satellite antenna
input Mains cable
To Mains
socket
SS
TV
13/18V
500mA Max.
LNB1IN LNB2IN
LNB1 OUT LNB2OUT
UPGRADE ONLY TV ANT IN
SPDIF L-AUDIO-R VIDEO
L
R
AC 110-240V~
50/60Hz
30W Max.
OFF
ON
POWER
Y Cb Cr
TO TV
HDMI ETHERNET Z1082
Satellite antenna
input Mains cable
To Mains
socket
SS
HDMI in TV
13/18V
500mA Max.
LNB1IN LNB2IN
LNB1 OUT LNB2OUT
UPGRADE ONLY TV ANT IN
SPDIF L-AUDIO-R VIDEO
L
R
AC 110-240V~
50/60Hz
30W Max.
OFF
ON
POWER
Y Cb Cr
TO TV
HDMI ETHERNET Z1082
Satellite antenna
input
Component
Audio in Component in
Mains cable
To Mains
socket
SS
TV
13/18V
500mA Max.
LNB1IN LNB2IN
LNB1 OUT LNB2OUT
UPGRADE ONLY TV ANT IN
SPDIF L-AUDIO-R VIDEO
L
R
AC 110-240V~
50/60Hz
30W Max.
OFF
ON
POWER
Y Cb Cr
TO TV
HDMI ETHERNET Z1082
Satellite antenna
input
AV in
Mains cable
To Mains
socket
SS
TV
13/18V
500mA Max.
LNB1IN LNB2IN
LNB1 OUT LNB2OUT
UPGRADE ONLY TV ANT IN
SPDIF L-AUDIO-R VIDEO
L
R
AC 110-240V~
50/60Hz
30W Max.
OFF
ON
POWER
Y Cb Cr
TO TV
HDMI ETHERNET Z1082
Satellite antenna
input
Mains cable
Antenna in
To Mains
socket
SS
QUICK REFERENCE GUIDE DTVS-DSR2
CONNECT TO YOUR TV, USE ANY OF THE
FOLLOWING 4 OPTIONS
CONNECTING YOUR SATELLITE DISH
c) Connecting via Compositea) Connecting via HDMI
d) Connecting via RF
b) Connecting via Component
When using the RF output to
connect the receiver to the
television please ensure that you
tune in the receiver to a channel
on your TV. The default UHF
channel is set to 21.
a) Connect the satellite dish cable to
LNB1IN.
b) Connect one end of the supplied
loop cable to LNB1OUT.
c) Connect the other end of the loop
cable to LNB2IN.
In the main menu you can press
the buttons to select System
Conguration and use the buttons
to select RF Setup and then press the
buttons to choose the options
to adjust the settings.
2
1
• Connect mains plug last, ensure your receiver is connected to the TV and Dish
before plugging in to mains power.
• Please follow this guide for a successful rst time set up.
• Read all the safety instructions carefully before use and keep the instruction
manual for future reference.

TUNING INSTRUCTIONS
3
Step 2Step 1
Step 4
Step 3
When your set-top-box is switched on for the rst
time, a Setup Screen will be displayed. Use the
buttons to select the region and press the
OK button on the remote control or the Unit to
conrm.
Plug in the mains plug into the mains socket after
you have completed all the connections.
Then you can turn switch on on rear panel of your
set-top-box.
During the channel search, the channel found will
be displayed. Please allow a few minutes for the
channels to be tuned in.
Troubleshooting
If you get a "Tuning Failed" or "Database Empty" message, please try the following:
1) Check your connections to the satellite dish.
2) Ensure your dish is installed correctly.
3) Retry installation after performing "Factory Default"
For further assistance you can check for more information on the DTV Solutions website, www.dtvs.co.nz or call the
help line number. 0800 388 765
Step 5
Once all the channels are found the receiver will save the channels and exit automatically and you can begin watching
the channels.
The receiver will automatically detect the signal
and will show progress and signal quality. Once a
signal is found, the receiver will begin searching for
channels.