Dual XDMR7700 Operating instructions

INSTALLATION/OWNER’S MANUAL
XM Ready Multimedia Receiver with Detach Face
XDMR7700
An optional XM Satellite Radio Receiver may be connected to the XDMR7700.
XM subscription is required for reception. For more information, visit XM’s website at
www.xmradio.com or call 1-877-XMRADIO. Not available in Alaska or Hawaii.

2
XDMR7700 INSTALLATION
Preparation
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
KEYS
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. (consult a qualified technician for instructions)
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. (consult a qualified
technician if you are unsure)
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
• Mount the iplug™adapter to any
smooth clean surface using the
supplied double-sided tape or
#2 x 3/8” Phillips head screws.

3
XDMR7700 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDMR7700 uses one
10 amp ATM fuse located
beside the wiring connector.

4
XDMR7700 OPERATION
Control Locations - Receiver
Open
Tune/Track Down
AS/PS/Enter/Function
Mode/Search/Shift
Tune/Track Up
Audio
Volume
Display
Tuner Scan/*Preset 8
Local/Distance/*Preset 7
Loudness/*Preset 10
EQ/*Preset 9
1
2
3
4
5
6
7
8
9
10
Eject
Mute
Infrared Sensor
Preset 6/Category-Folder Up
Preset 5/Category-Folder Down
Preset 4
Preset 3/CD Intro
Preset 2/CD Random
Preset 1/CD Repeat
Band/Pause/Scroll
Power
Reset
13
14
15
16
17
18
19
20
21
22
23 22 21 20 19 18 17 16 15 14
1 2 4 789 310
5611
24
11
12
23
24
12 13
An optional XM Satellite Radio Receiver may be connected to the XDMR7700.
XM subscription is required for reception. For more information, visit XM’s website at
www.xmradio.com or call 1-877-XMRADIO. Not available in Alaska or Hawaii.
*Function buttons 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only.

EQ/*Preset 9
Tuner Scan/*Preset 8
Local/Distance/*Preset 7
Preset 5/Category-Folder Down
Preset 4
Preset 1/CD Repeat
Mode/Search/Shift
Tune/Track Down
Band/Pause/Scroll
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
12
4
3
6
5
8
17
9
10
11
12
14
13
15
16
7
18
19
Power
Volume Up
AS/PS/Enter/Function
Audio
Tune/Track Up
Loudness/*Preset 10
Volume Down
Preset 3/CD Intro
Preset 2/CD Random
Preset 6/Category-Folder Up
XDMR7700 OPERATION
Control Locations - Remote
5

6
XDMR7700 OPERATION
General Operation
With the unit off, press OPEN to allow the front panel to slide
down. Gently squeeze the release tab located on the bottom
center underside and pull faceplate down and away from unit
to remove. To install, insert left side faceplate first, then push
right side to secure.
Before installation, remove trim ring and install supplied
Phillips head #1 x 7/32” screws through left and right
underside of faceplate tray into faceplate.
Press PWR or any other button (except EJECT or OPEN) to turn
the unit on. Inserting a CD will turn the unit on automatically.
Press PWR to turn the unit off.
Press MODE to select between AM/FM, *XM Radio, CD player
and auxiliary input. Modes of operation are indicated in the
display.
*Optional XM Satellite Radio Receiver and subscription
required for XM Radio operation.
Adjust volume using rotary encoder (00-46).
Press and hold POWER for 3 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Press SHIFT for 2 seconds to activate the SHIFT function.
The SHIFT icon will appear in the display. In XM Radio mode,
the SHIFT function must be active to access the LOUDNESS
and EQ functions. Press SHIFT again for 2 seconds to cancel.
Note:
The SHIFT function only applies to XM Radio operation.
Press LOUD to activate and deactivate loudness contour curve.
Activating this feature will enhance the bass and treble
frequencies when listening to music at low volumes.
Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK
and OFF (default) equalization curves. Any adjustment to the
Bass or Treble settings automatically cancels the current EQ
curve.
Faceplate Removal
Semi-permanent
Faceplate Installation
Power On/Off
Mode
Volume
Programmable
Turn-On Volume
Shift Function
Loudness
Preset EQ Curves

7
XDMR7700 OPERATION
General Operation
When in AM/FM, CD or AUX mode:
Press DISP to select between clock and radio frequency
(tuner mode), clock and CD elapsed time/track (CD mode), or
clock and AUX (AUX mode).
When in XM Radio mode:
Press DISP to select between channel name, artist name,
song title or clock.
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE
nn
to adjust the hours
and TUNE
ll
to adjust the minutes. Press DISP
momentarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
In AM/FM tuner mode, press and hold DISP then press
TUNE
ll
to select function priority display. “FREQ” will
momentarily appear in the display.
Note:
"FUNC" will appear in XM, CD or AUX modes.
Radio frequency (tuner mode), XM information (XM mode),
CD elapsed time/track (CD mode) or AUX (AUX mode) will be
displayed by default.
Note:
When playing MP3/WMA files, the track number/elapsed
time, track name, directory name, title, artist, album, year or
comment will be displayed by default. Clock is accessed by
pressing DISP momentarily.
Press and hold DISP then press TUNE
nn
to select time
display priority. “TIME” will momentarily appear in the
display. Clock will be displayed by default. Radio frequency
(tuner mode), XM information (XM mode), CD elapsed
time/track or MP3/WMA file information (CD mode) is
accessed by pressing DISP momentarily.
Display
Set the Clock
12/24-hour Clock
Programmable Display
Priority

8
XDMR7700 OPERATION
General Operation
Press and hold for more than 2 seconds to RESET the unit
upon initial installation or if abnormal operation occurs.
The reset button is located above the PWR button.
Press and hold AUD for 3 seconds to turn confirmation
beep on/off.
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
Press AUD to select between Volume (default), Bass,
Treble, Balance & Fader.
Press AUD until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press AUD until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press AUD until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Press AUD until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Individual Bass and Treble settings are retained in memory
for AM, FM, XM, CD, and AUX modes. This allows you to
save the Bass and Treble settings separately for each
mode.
Example:
FM tuner mode can have Bass +3 and Treble -1 while CD
mode can have Bass +2 and Treble +2.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
Reset
Confirmation Beep
Mute
Audio
Bass
Treble
Balance
Fader
Source Audio Memory

Press TUNE
nn
or TUNE
ll
momentarily to seek the
next strong station.
Press TUNE
nn
or TUNE
ll
for more than 2 seconds,
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
nn
or TUNE
ll
momentarily to
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for 5
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
Press SCAN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCAN again to cancel.
Press LO/DX to activate local tuning for strong station
reception only. Press LO/DX again to cancel and resume
Distance tuning (default).
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Press and hold BAND then press TUNE
nn
to select
European frequency spacing. Press and hold BAND then
press TUNE
ll
to select USA frequency spacing (default).
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Note:
Function buttons 7, 8, 9 and 0 apply to XM Radio and
MP3/WMA operation only.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Local/Distance is activated during the initial band scan.
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
9
XDMR7700 OPERATION
AM/FM Tuner Operation
Seek Tuning
Manual Tuning
Scan Tuning
Local/Distance
Band
Frequency Spacing
Storing and Recalling
Station Presets
Automatically Store
Stations
Preset Scan

10
XDMR7700 OPERATION
XM Radio Activation
Activating Your XM Receiver
(Optional)
Tuning Modes
Basic Channel Selection
Direct Channel Selection
Category Recall
1. Press MODE to select XM Radio.
2. Verify channel 1 (XM Preview Channel) is playing.
3. Select Channel 0. The XM receiver’s eight character Radio
ID number will appear on the XDMR7700 display.
The Radio ID number is also located on the top of the
XM receiver unit (sold separately).
4. Record the number here for future reference:
5. Activate your XM Satellite Radio service.
To subscribe, log onto http://www.xmradio.com/activation or
call 1-800-852-9696.
Note:
You will need to keep your XDMR7700 turned on for at least
one hour after requesting activation to receive the full
channel line-up.
Press BAND to select between XM DIRECT, XM1 and XM2
bands.
Press TUNE
nn
or TUNE
ll
momentarily to select the
next available channel. Press and hold to advance quickly.
Press BAND to select XM DIRECT channel entry band.
“DIRECT” will momentarily appear in the display. Enter
the desired channel using preset buttons (1-0), then press
FUNC for 3 seconds to confirm the selected channel. If the
channel is not available, "CH ---" will momentarily appear
in the display and the current channel will be retained.
Press FUNC once to display the category of the currently
selected channel for 10 seconds. The CATEGORY icon will
appear on the display.
XM Radio - Operation