Duluth Forge FDSR25 Specification sheet

VENT-FREE GAS STOVE
OWNER’S OPERATION AND
INSTALLATION MANUAL
MODELS
FDSR25 & FDSR25GF
PFS
®
US
WARNING: If the information in this manual is not
followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other ammable va-
pors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re
department.
— Installation and service must be performed by a quali-
ed installer, service agency or the gas supplier.
WARNING: This appliance is equipped for natural and
propane gas. Field conversion is not permitted other than
between natural or propane gases.
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-855-607-6557, 8:00 am - 4:30 pm EST,
Monday through Friday or email [e-mail]

www.factorybuysdirect.com 200257-01A
2
TABLE OF CONTENTS
Safety ........................................................ 3
Specications ............................................ 4
Qualied Installing Agency ........................ 5
Product Features....................................... 5
Local Codes............................................... 5
Product Identication................................. 6
Unpacking.................................................. 6
Water Vapor: A By-Product Of
Unvented Room Heaters..................... 6
Air For Combustion and Ventilation ........... 7
Installation ................................................. 8
Operation................................................. 18
Inspecting Burners................................... 22
Care And Maintenance ............................ 23
Electrical.................................................. 24
Troubleshooting....................................... 26
Service Hints ........................................... 29
Technical Service..................................... 29
Accessories ............................................. 29
Parts ........................................................ 30
Replacement Parts.................................. 31
Warranty .................................................. 32
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This is an unvented gas-red stove. It uses air (oxygen)
from the room in which it is installed. Provisions for ad-
equate combustion and ventilation air must be provided.
Refer to Air For Combustion and Ventilation section on
page 7 of this manual.
WARNING: Improper installation, adjustment, al-
teration, service or maintenance can cause injury or
property damage. Refer to this manual for correct in-
stallation and operational procedures. For assistance
or additional information consult a qualied installer,
service agency or the gas supplier.
This appliance may be installed in an aftermarket,* per-
manently located, manufactured (mobile) home, where
not prohibited by local codes.
This appliance is only for use with propane or natural
gas. Field conversion by any other means including the
use of a kit is not permitted.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
SAVE THIS BOOK
PATENT INFORMATION
This product may be covered by one or more of the following United States patents:
8,915,239 8,851,065 8,764,436 8,757,202 8,757,139 8,752,541 8,568,136
8,545,216 8,517,718 8,516,878 8,506,290 8,465,277 8,317,511 8,297,968
8,281,781 8,241,034 8,235,708 8,152,515 8,011,920 7,967,006 7,967,007
7,654,820 7,730,765 7,677,236 7,607,426 7,434,447

www.factorybuysdirect.com
3
200257-01A
SAFETY
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble,
operate, or service this stove.
Improper use of this stove can
cause serious injury or death
from burns, fire, explosion,
electrical shock and carbon
monoxide poisoning. Failure
to follow these instructions will
void the warranty.
Only a qualied installer, service
agent, or local gas supplier may
install and service this product.
WARNING: Keep the appli-
ance area clear and free from
combustible materials, gasoline,
and other ammable vapors and
liquids.
WARNING: This appliance
can be used with propane or
natural gas. It is shipped from
the factory adjusted for use with
propane.
DANGER: Carbon monoxide
poisoning may lead to death!
CARBON MONOXIDE POISONING: Early
signs of carbon monoxide poisoning resemble
the u, with headaches, dizziness or nausea.
If you have these signs, the stove may not be
working properly. Get fresh air at once! Have
stove serviced. Some people are more af-
fected by carbon monoxide than others. These
include pregnant women, people with heart or
lung disease or anemia, those under the inu-
ence of alcohol and those at high altitudes.
NATURAL AND PROPANE/LP GAS: Natural
and Propane/LP gas are odorless. An odor-
making agent is added to the gas. The odor
helps you detect a gas leak. However, the
odor added to the gas can fade. Gas may be
present even though no odor exists.
WARNING: Any change to
this stove or its controls can be
dangerous.
WARNING: Do not allow fans
to blow directly into stove. Avoid
any drafts that alter burner ame
patterns.
WARNING: Do not use a
blower insert, heat exchanger
insert or other accessory not
approved for use with this stove.
WARNING: Due to high tem-
peratures, the appliance should
be located out of trafc and away
from furniture and draperies.
WARNING: Do not place
clothing or other flammable
material on or near the appli-
ance. Never place any objects
in the stove.
WARNING: The stove be-
comes very hot when operating.
Keep children and adults away
from hot surfaces to avoid burns
or clothing ignition. Stove will
remain hot for a time after shut-
down. Allow surfaces to cool
before touching.
WARNING: Carefully super-
vise young children when they
are in the room with the stove.
WARNING: You must oper-
ate this stove with the door and
screen in place.

www.factorybuysdirect.com 200257-01A
4
1. Do not place Propane/LP supply tank(s)
inside any structure. Propane/LP supply
tank(s) must be placed outdoors.
2. This stove shall not be installed in a bed-
room or bathroom.
3. This stove needs fresh air ventilation to
run properly. This stove has an Oxygen
Depletion Sensing (ODS) safety shutoff
system. The ODS shuts down the stove if
not enough fresh air is available. See Air
for Combustion and Ventilation, pages 7.
If stove keeps shutting off, see Trouble-
shooting, page 26.
4. Keep all air openings in front and bottom
of stove clear and free of debris. This will
ensure enough air for proper combustion.
5. If stove shuts off, do not relight until you
have provided fresh, outside air. If stove
keeps shutting off, have it serviced.
6. Do not run stove:
• Where ammable liquids or vapors are
used or stored.
• Under dusty conditions.
7. Before using furniture polish, wax, carpet
cleaner, or similar products, turn stove off.
If heated, the vapors from these products
may create a white powder residue within
burner box or on adjacent walls or furni-
ture.
8. Do not use stove if any part has been
under water. Immediately call a qualied
service technician to inspect the room
stove and to replace any part of the control
system and any gas control which has
been under water.
SAFETY
9. Turn stove off and let cool before servic-
ing. Only a qualied service person should
service and repair stove.
10. Operating stove above elevations of 4,500
feet could cause pilot outage.
11. To prevent performance problems, do
not use propane/LP fuel tank of less than
100 lbs. capacity.
12. Do not use this stove as a wood-burning
stove. Use only the logs provided with the
stove.
13. Solid fuels should not be burned in a stove
in which a vent-free log set is installed. Do
not use this stove to cook food or burn
paper or other objects.
14. To prevent sooting, follow the instructions
in Care and Maintenance (see page 23).
15. Do not add extra logs or ornaments such
as pine cones, vermiculite, or rock wool.
Using these added items can cause soot-
ing. Do not add lava rock around base.
Rock and debris could fall into the control
area of stove. After servicing, always close
door before operating stove.
16. This stove is designed to be smokeless. If
logs ever appear to smoke, turn off stove
and call a qualied service person.
Note: During initial operation, slight smok-
ing could occur due to log curing and the
stove burning manufacturing residues.
17. Do not use this stove if any log is broken.
Do not operate stove if a log has a chip
(dime-sized of larger).
SPECIFICATIONS
Gas Type Natural Gas Propane Gas
Input Rating 26,000 Btu/Hr 26,000 Btu/Hr
Ignition Electronic Piezo Electronic Piezo
Regulator Pressure Setting 4" W.C. 9" W.C.
Inlet Gas Pressure* (inches of water)
(*for purposes of input adjustment)
Maximum 9" Maximum 14"
Minimum 5" Minimum 11"
Stove Dimensions (HxWxD) • 26.125" × 28" × 16.875"
Carton Dimensions (HxWxD) • 31.125" × 31.375" × 20.5"
Stove Weight • 73 lbs Shipping Weight • 85 lbs
120 Volts • 19 Watts

www.factorybuysdirect.com
5
200257-01A
QUALIFIED INSTALLING AGENCY
Only a qualied agency should install and
replace gas piping, gas utilization equipment
or accessories, and repair and equipment ser-
vicing. The term “qualied agency” means any
individual, rm, corporation, or company that
either in person or through a representative
is engaged in and is responsible for:
a) Installing, testing, or replacing gas piping
or
b) Connecting, installing, testing, repairing,
or servicing equipment; that is experienced
in such work; that is familiar with all precau-
tions required; and that has complied with
all the requirement of the authority having
jurisdiction.
PRODUCT FEATURES
SAFETY PILOT
This stove has a pilot with an Oxygen Deple-
tion Sensing (ODS) safety shutoff system.
The ODS/pilot shuts off the stove if there is
not enough fresh air.
PIEZO IGNITION SYSTEM
This stove is equipped with an electronic piezo
control system. This system requires one AAA
battery (provided).
THERMOSTATIC CONTROL
The control automatically cycles the burner
on and off to maintain a desired room tem-
perature.
2 GAS OPTIONS AVAILABLE
Your stove is equipped to operate on either
Propane/LP or Natural gas. The stove is
shipped from the factory ready for connect-
ing to Propane/LP. The stove can easily be
changed to Natural gas by having your quali-
ed installer follow the instructions on page
10 and the markings on the stove.
MANUAL OVERRIDE CONTROL
SYSTEM
This stove has two operation functions. Re-
mote Control and Manual Override Control.
The remote control has a transmitter, which
requires two AAA batteries and electric power
outlet to operate. In the event of a power
outage, you can operate the the stove by
manual override.
LOCAL CODES
Install and use stove with care. Follow all local
codes. In the absence of local codes, use the
latest edition of The National Fuel Gas Code,
ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
1 Batterymarch Park
Quincy, MA 02269-9101
This stove is designed for vent-free operation.
State and local codes in some areas prohibit
the use of vent-free stoves.
State of Massachusetts: The installation
must be made by a licensed plumber or
gas tter in the Commonwealth of Mas-
sachusetts.
Sellers of unvented propane or natural
gas-red supplemental room heaters shall
provide to each purchaser a copy of 527
CMR 30 upon sale of the unit.
In the State of Massachusetts the gas
cock must be a T-handle type. The State
of Massachusetts requires that a exible
appliance connector cannot exceed three
feet in length.

www.factorybuysdirect.com 200257-01A
6
WATER VAPOR: A BY-PRODUCT OF
UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combus-
tion. An unvented room heater produces ap-
proximately one (1) ounce (30 mL) of water
for every 1,000 BTUs (0.3 KWs) of gas input
per hour. Unvented room heaters are recom-
mended as supplemental heat (a room) rather
than a primary heat source (an entire house).
In most supplemental heat applications, the
water vapor does not create a problem. In
most applications, the water vapor enhances
the low humidity atmosphere experienced
during cold weather.
The following steps will help ensure that water
vapor does not become a problem.
1. Be sure the heater is sized properly for the
application, including ample combustion
air and circulation air.
2. If high humidity is experienced, a dehu-
midier may be used to help lower the
water vapor content of the air.
3. Do not use an unvented room heater as
the primary heat source.
UNPACKING
1. Remove top inner pack.
2. Tilt carton so that stove is upright.
3. Remove protective side packaging.
4. Slide stove out of carton.
5. Remove protective plastic wrap.
Figure 1 - Vent-Free Stove
PRODUCT IDENTIFICATION
Logs
Screen
Stove Controls
(Inside Panel)
Stove Door
6. Rotate door handle and open door.
7. Carefully remove logs.
8. Carefully unwrap logs.
9. Check for any shipping damage. If stove
or log is damaged, contact our customer
service department.

www.factorybuysdirect.com
7
200257-01A
AIR FOR COMBUSTION AND VENTILATION
WARNING: This heater shall
not be installed in a conned
space or unusually tight con-
struction unless provisions are
provided for adequate combus-
tion and ventilation air. Read the
following instructions to insure
proper fresh air for this and other
fuel-burning appliances in your
home.
Today’s homes are built more energy efcient
than ever. New materials, increased insulation
and new construction methods help reduce
heat loss in homes. Home owners weather
strip and caulk around windows and doors
to keep the cold air out and the warm air in.
During heating months, home owners want
their homes as airtight as possible.
While it is good to make your home energy
efcient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning ap-
pliances need fresh air for proper combustion
and ventilation.
Exhaust fans, replaces, clothes dryers and
fuel burning appliances draw air from the
house to operate. You must provide adequate
fresh air for these appliances. This will insure
proper venting of vented fuel-burning appli-
ances.
WARNING: This heater shall
not be installed in a room or
space unless the required vol-
ume of indoor combustion air
is provided by the method de-
scribed in the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, the
International Fuel Gas Code, or
applicable local codes.
WARNING: Ifthearea inwhich
the heater may be operated does
not meet the required volume for
indoor combustion air, combus-
tion and ventilation air shall be
provided by one of the methods
described in the National Fuel
Gas Code,ANSI Z223.1/NFPA54,
the International Fuel Gas Code,
or applicable local codes.
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining
unconned space. When ventilating to an
adjoining unconned space, you must provide
two permanent openings: one within 12" of the
ceiling and one within 12" of the oor on the
wall connecting the two spaces (see options
1 and 2, Figure 2). You can also remove door
into adjoining room (see option 3, Figure 4).
Follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Air for Combustion and
Ventilation for required size of ventilation
grills or ducts.
Figure 4 - Ventilation Air from Inside
Building
Or
Remove
Door into
Adjoining
Room,
Option
3
Ventilation Grills
Into Adjoining Room,
Option 2
Ventilation
Grills Into
Adjoining
Room,
Option 1
12"
12"

www.factorybuysdirect.com 200257-01A
8
Ventilation Air From Outdoors
AIR FOR COMBUSTION AND VENTILATION
Figure 5 - Ventilation Air from Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two perma-
nent openings: one within 12" of the ceiling
and one within 12" of the oor. Connect these
items directly to the outdoors or spaces open
to the outdoors. These spaces include attics
and crawl spaces. Follow the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Air for
Combustion and Ventilation for required size
of ventilation grills or ducts.
IMPORTANT: Do not provide openings
for inlet or outlet air into attic if attic has a
thermostat-controlled power vent. Heated air
entering the attic will activate the power vent.
Rework worksheet, adding the space of the
adjoining unconned space. The combined
spaces must have enough fresh air to supply
all appliances in both spaces.
Outlet
Air
Ventilated
Attic
Outlet
Air
Inlet
Air
Inlet Air Ventilated
Crawl Space
To
Crawl
Space
To Attic
INSTALLATION
NOTICE: This stove is intended
for use as supplemental heat.
Use this stove along with your
primary heating system. Do not
install this stove as your primary
heat source. If you have a cen-
tral heating system, you may
run system’s circulating blower
while using stove. This will help
circulate the heat throughout the
house. In the event of a power
outage, you can use this stove
as your primary heat source.
WARNING: A qualied ser-
vice person must install stove.
Follow all local codes.
WARNING:ElectricalGround-
ing Instructions If using a blower,
this appliance is equipped with a
three-prong (grounding) plug for
your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle.
WARNING: Never install the
stove
• in a bedroom or bathroom
• in a recreational vehicle
• wherecurtains,furniture,cloth-
ing, or other ammable objects
are less than 48" from the front,
top, or sides of the stove.
• in high trafc areas
• in windy or drafty areas
CAUTION: This stove creates
warm air currents. These currents
move heat to wall surfaces next
to stove. Installing stove next to
vinyl or cloth wall coverings or
operating stove where impurities
(such as tobacco smoke, aromatic
candles, cleaning uids, oil or
kerosene lamps, etc.) in the air
exist, may cause walls to discolor.
IMPORTANT: Vent-free heaters add moisture
to the air. Although this is benecial, installing
heater in rooms without enough ventilation air
may cause mildew to form too much moisture.
See Air for Combustion and Ventilation, pages 7.

www.factorybuysdirect.com
9
200257-01A
Gas Inlet / Gas esté
INLETGAS PRESSURE MAX 1/2 PSIG (3.5 KPa)
200110-01B
03/15
WARNING:Make sure Regulator Cap is in the appropriate position
asshown in diagrams. Installation and service should be done by
qualifiedservice technician only.
NaturalGas
Whenusing natural gas:
Make sure the cap is installed in the propane/LP inlet of regulator.
Use thread sealant to assure there are no leaks.
Propane/LPGas
Whenusing propane/LP gas:
Make sure the cap is installed in the natural gas (NG) inlet of regulator.
Use thread sealant to assure there are no leaks.
ADVERTENCIA:Asegúrese la tapa del regulador esté en la posición adecuada,
comose muestra en los diagramas. La instalación y reparaciones deben ser realizadas
porun técnico de servicio calificado solamente.
GasNatural
Cuandose utiliza gas natural:
Asegúrese de que la tapa está instalado en el propano/LP entrada del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
Propano/LPGas
Cuandose utiliza el gas propano / LP:
Asegúresede que la tapa está instalado en la entrada de gas natural (GN) del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
CorrectPilot Flame Pattern
IncorrectPilot Flame Pattern
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
1/2Glas
s
Height
1/2Glas
s
Height
Yellow
Tipping
CorrectBurner Flame Pattern
IncorrectBurner Flame Pattern
LP
BluePlunger
INSTALLSUPPLIED CAP IN FITTING
NOTBEING USED.
INSTALARTAPASUMINISTRADA MONTAJE NO SE UTILIZA.
NG
YellowPlunger
Thisappliance may be installed in an aftermarket,*
permanentlylocated, manufactured (mobile) home, where
notprohibited by local codes.
Thisappliance is only for use with propane or natural gas.
Fieldconversion by any other means including the use of
akit is not permitted.
WARNING:Make sure the supplied cap is
installedin unused regulator fitting before
connectingthe correct gas supply line.
WARNING:Do not use natural gas and
propanegas together.
CAUTION:Two gas line installations at
thesame time are prohibited.
ADVERTENCIA:Asegúrese de que la línea
noutilizado se conecta por primera vez
antesde conectar la línea de suministro
degas correcta.
ADVERTENCIA:No utilice el gas natural y
elgas propano juntos.
PRECAUCIÓN:Dos instalaciones de
líneasde gas al mismo tiempo están
prohibidos.
FORPROPANE GAS SUPPLY
PARALA FUENTE DE GAS DEL PROPANE
CAUTION:The heater requires an external regulator to reduce
theLP tank pressure to a maximum of 14" W.C. Never connect
thisproduct directly to the supply tank.
PRECAUCIÓN:El calentador requieres una externa regulador
parareducir la presión del tanque de gas a un máximo de 14"
W.C.Nunca conecte este producto directamente al tanque de
suministro.
FORNATURAL GAS SUPPLY
PARALA FUENTE DE GAS DEL NATURAL
NOTICE:An additional gas regulator will be necessary if the
localnatural gas pressure exceeds the heater's rated maximum
inletpressure. If in doubt, contact the local gas utility. If natural
gasinlet pressure exceeds 10" W.C., the safety pressure switch
willactivate. See owners manual for proper procedure to bypass
thepressure switch.
AVISO:Un regulador de gas adicional será necesario si la
presióndel gas natural local excede de entrada nominal máxima
delcalentador presión. En caso de duda, póngase en contacto
conla compañía de gas local. Si la presión de entrada de gas
naturalsupera los 10" WC, el interruptor de presión de
seguridadse activará. Consulte el manual del propietario para el
procedimientoadecuado de derivación el interruptor de presión.
ProcomHeating, Inc. U.S. Patent Information
Thisproduct may be covered by one or more of the following
UnitedStates patents:
8,915,239 8,851,065 8,764,436 8,757,202 8,757,139 8,752,541
8,568,136 8,545,216 8,517,718 8,516,878 8,506,290 8,465,277
8,317,511 8,297,968 8,281,781 8,241,034 8,235,708 8,152,515
8,011,920 7,967,006 7,967,007 7,654,820 7,730,765 7,677,236
7,607,426 7,434,447
Otherpatents pending.
TOLL-FREECustomer Care Number: 1-866-573-0674
Numerode Atención al Cliente GRATUITO:1-866-573-0674
Visitour website for more information www.usaprocom.com
Visitenuestra página web para más informacion www.usaprocom.com
Figure 7 - Minimum Clearance to Wall
and Ceiling
Figure 6 - Connecting to Power Supply
Ceiling
12"
Min.
12"
Min.
48"
Min.
Side
Wall
Side
Wall
Floor
CONNECTING ELECTRICAL
SUPPLY
This stove requires an 120V electrical outlet
within 4 feet of the unit. This is a power supply
for the remote receiver located in the bottom
of the stove. Extensions cords may be used.
The remote receiver requires 4 AA batteries.
This powers the stove in case of an electrical
power outage.
1. Locate 6V DC adapter.
2. Plug connector end of adapter into the
power change assembly on the back of
the stove.
3. Plug adapter into a 120V electrical outlet.
INSTALLATION
Corner
Front of
Stove Unit
Front of
Stove Unit
Wall
Wall
Ceiling
Back Wall
Back
Wall
Top View
Side
View
Side
Wall
Side
Wall
10"
Minimum
48"
Minimum
10"
Minimum
6"
Minimum
12"
Minimum
12"
Minimum
6"
Minimum
This stove is designed to sit directly on the
oor or on a mantel base.
IMPORTANT: You must maintain minimum
wall and ceiling clearances during installation.
The minimum clearances are shown in Figure
7. Measure from outermost point of stove.
Minimum Wall and Ceiling
Clearances
A. Clearances from outermost point of stove
to any combustible side wall should not be
less than 12".
B. Clearances from the stove to the ceiling
should not be less than 48".
C. Clearance from stove to back wall should
not be less than 6".
Blower Accessory
If using a blower accessory, install at this time.
See instructions included with blower.
CHECK GAS TYPE
Be sure your gas supply is right for your stove.
Otherwise, call dealer where you bought the
stove for proper type stove.
CLEARANCES TO
COMBUSTIBLES
WARNING: You must main-
tain the minimum clearances. If
you can, provide greater clear-
ances from oor, ceiling, and
adjoining wall. Measure from
outermost point of stove.
Connector
End of
Adapter
Power Change
Assembly

www.factorybuysdirect.com 200257-01A
10
Gas Inlet / Gas esté
INLETGAS PRESSURE MAX 1/2 PSIG (3.5 KPa)
200110-01B
03/15
WARNING:Make sure Regulator Cap is in the appropriate position
asshown in diagrams. Installation and service should be done by
qualifiedservice technician only.
NaturalGas
Whenusing natural gas:
Make sure the cap is installed in the propane/LP inlet of regulator.
Use thread sealant to assure there are no leaks.
Propane/LPGas
Whenusing propane/LP gas:
Make sure the cap is installed in the natural gas (NG) inlet of regulator.
Use thread sealant to assure there are no leaks.
ADVERTENCIA:Asegúrese la tapa del regulador esté en la posición adecuada,
comose muestra en los diagramas. La instalación y reparaciones deben ser realizadas
porun técnico de servicio calificado solamente.
GasNatural
Cuandose utiliza gas natural:
Asegúrese de que la tapa está instalado en el propano/LP entrada del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
Propano/LPGas
Cuandose utiliza el gas propano / LP:
Asegúresede que la tapa está instalado en la entrada de gas natural (GN) del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
CorrectPilot Flame Pattern
IncorrectPilot Flame Pattern
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
1/2Glas
s
Height
1/2Glas
s
Height
Yellow
Tipping
CorrectBurner Flame Pattern
IncorrectBurner Flame Pattern
LP
BluePlunger
INSTALLSUPPLIED CAP IN FITTING
NOTBEING USED.
INSTALARTAPASUMINISTRADA MONTAJE NO SE UTILIZA.
NG
YellowPlunger
Thisappliance may be installed in an aftermarket,*
permanentlylocated, manufactured (mobile) home, where
notprohibited by local codes.
Thisappliance is only for use with propane or natural gas.
Fieldconversion by any other means including the use of
akit is not permitted.
WARNING:Make sure the supplied cap is
installedin unused regulator fitting before
connectingthe correct gas supply line.
WARNING:Do not use natural gas and
propanegas together.
CAUTION:Two gas line installations at
thesame time are prohibited.
ADVERTENCIA:Asegúrese de que la línea
noutilizado se conecta por primera vez
antesde conectar la línea de suministro
degas correcta.
ADVERTENCIA:No utilice el gas natural y
elgas propano juntos.
PRECAUCIÓN:Dos instalaciones de
líneasde gas al mismo tiempo están
prohibidos.
FORPROPANE GAS SUPPLY
PARALA FUENTE DE GAS DELPROPANE
CAUTION:The heater requires an external regulator to reduce
theLP tank pressure to a maximum of 14" W.C. Never connect
thisproduct directly to the supply tank.
PRECAUCIÓN:El calentador requieres una externa regulador
parareducir la presión del tanque de gas a un máximo de 14"
W.C.Nunca conecte este producto directamente al tanque de
suministro.
FORNATURAL GAS SUPPLY
PARALA FUENTE DE GAS DELNATURAL
NOTICE:An additional gas regulator will be necessary if the
localnatural gas pressure exceeds the heater's rated maximum
inletpressure. If in doubt, contact the local gas utility. If natural
gasinlet pressure exceeds 10" W.C., the safety pressure switch
willactivate. See owners manual for proper procedure to bypass
thepressure switch.
AVISO:Un regulador de gas adicional será necesario si la
presióndel gas natural local excede de entrada nominal máxima
delcalentador presión. En caso de duda, póngase en contacto
conla compañía de gas local. Si la presión de entrada de gas
naturalsupera los 10" WC, el interruptor de presión de
seguridadse activará. Consulte el manual del propietario para el
procedimientoadecuado de derivación el interruptor de presión.
ProcomHeating, Inc. U.S. Patent Information
Thisproduct may be covered by one or more of the following
UnitedStates patents:
8,915,239 8,851,065 8,764,436 8,757,202 8,757,139 8,752,541
8,568,136 8,545,216 8,517,718 8,516,878 8,506,290 8,465,277
8,317,511 8,297,968 8,281,781 8,241,034 8,235,708 8,152,515
8,011,920 7,967,006 7,967,007 7,654,820 7,730,765 7,677,236
7,607,426 7,434,447
Otherpatents pending.
TOLL-FREECustomer Care Number: 1-866-573-0674
Numerode Atención al Cliente GRATUITO:1-866-573-0674
Visitour website for more information www.usaprocom.com
Visitenuestra página web para más informacion www.usaprocom.com
INSTALLATION
Figure 8 - Back of Stove
Gas Connection
Yellow Natural Gas
Plunger Underneath
Metal Cap
Blue Propane/LP Gas
Plunger Underneath
Dust Cover
Figure 9 - Gas Regulator
Insert Gas Fitting
for Natural Gas
Insert Gas Fitting
for Propane/LP Gas
Fitting supplied with the product located in
the hardware bag. Fitting part number:
160960-02 (straight)
160960-03 (elbow)
Blue Dust Cover DO NOT REMOVE
Blue Propane/LP Plunger
Install Gas Fitting Here
GAS SELECTION
This appliance is factory
preset for propane/LP gas.
No changes are required for
connecting to propane/LP.
Only a qualied installer or service
technician can perform gas selec-
tion and connecting to gas supply.
CAUTION: Two gas line in-
stallations at the same time are
prohibited.
CAUTION: To avoid gas leak-
age for the gas not being used at
the inlet of regulator, a qualied
installer or service technician
must use supplied cap.
You will notice a color coded
plunger on the inside of the regu-
lator. This is normal. When the in-
let connection tting is inserted
and tightened, this plunger will
be pushed back by the tting
making all of the adjustments
for the gas being supplied. DO
NOT REMOVE THE PLUNGER.
The regulator will not work.
The inlet regulator is color coded
for identication of the correct
gas type. Blue is for propane (LP
gas) and yellow is for natural gas.
FOR PROPANE/LP GAS
INSTALLATION: BLUE
1. Remove blue dust cover.

www.factorybuysdirect.com
11
200257-01A
INSTALLATION
DO NOT use an off the shelf 3/8"
NPT pipe plug. This will damage
the plungers located inside the
regulator.
DO NOT try to remove the plung-
ers from inside the regulator. The
plunger will be pushed back as
the tting is installed.
Make sure the type of gas being
used is correct. Check to make
sure the connection tting is in
the correct inlet on the regula-
tor. Refer to Connecting to Gas
Supply, page 12.
If you are using natural gas
and the pilot will not light, see
Troubleshooting, page 26.
Blue Dust Cover
Metal Cap
Metal Cap
DO NOT REMOVE
Yellow Natural Gas Plunger
Install Gas Fitting Here
2. Apply thread sealant to the threads on
the connection tting. While pushing in,
rotate the tting clockwise until the threads
engage the regulator. After the tting has
been hand tightened into the regulator
use a wrench to complete tightening of the
tting. Install additional tting to connect
to the house supply.
FOR NATURAL GAS (NG)
INSTALLATION: YELLOW
1. Remove the blue dust cover from the
regulator.
2. Remove the metal cap installed over the
NG regulator inlet.
3. Install metal cap over LP/Propane regulator
inlet. This will keep debris out of regulator.
Use only the cap supplied on the
regulator. Do not use an off the
shelf pipe plug. This can damage
the plunger. The supplied regula-
tor cap is designed so it will not
engage the unused gas type.
4. Apply thread sealant to the threads on
the connection tting. While pushing in,
rotate the tting clockwise until the threads
engage the regulator. After the tting has
been hand tightened into the regulator
use a wrench to complete tightening of the
tting. Install additional tting to connect
to the house supply.

www.factorybuysdirect.com 200257-01A
12
INSTALLATION
CONNECTING TO GAS SUPPLY
WARNING: A qualied ser-
vice technician must connect
stove to gas supply. Follow all
local codes.
WARNING: This appliance
requires a 3/8" NPT (National
Pipe Thread) inlet connection to
the pressure regulator.
WARNING: For natural gas,
Never connect stove to private
(non-utility) gas wells. This gas
is commonly known as wellhead
gas.
CAUTION: For propane/LP gas,
never connect stove directly to the
gas supply. This stove requires an
external regulator (not supplied).
Install the external regulator be-
tween the stove and propane/LP
gas supply. Gas supplier provides
external regulator for natural gas.
The installer provides the external
regulator for propane/LP gas.
WARNING: Do not over-
tighten gas connections.
CAUTION: Use only new,
black iron or steel pipe. Inter-
nally tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of
1/2" diameter or greater to allow
proper gas volume to stove. If
pipe is too small, undue loss of
pressure will occur.
CAUTION: For natural gas,
check your gas line pressure
before connecting stove to gas
line. Gas line pressure must be
no greater than 9" of w.c. If gas
line pressure is higher, stove
regulator damage could occur.
CAUTION: Avoid damage to
regulator. Hold gas regulator
with wrench when connecting
into gas piping and/or ttings.
CAUTION: Use pipe joint
sealant that is resistant to gas
(Propane/LP or Natural Gas).
Before installing stove, make sure you have
the items listed below:
• external regulator for propane/LP unit only
(supplied by installer)
• piping (check local codes)
• sealant (resistant to natural gas and pro-
pane/LP gas)
• equipment shutoff valve*
• test gauge connection*
• sediment trap
• tee joint
• pipe wrench
• exible gas hose (check local codes)
* A CSA design-certied equipment shutoff
valve with 1/8" NPT tap is an acceptable al-
ternative to test gauge connection. Purchase
the optional CSA design certied equipment
shutoff valve from your dealer (see Acces-
sories, page 29).
Typical Inlet Pipe Diameters
Use 1/2" black iron pipe or greater. Installa-
tion must include an equipment shutoff valve,
union, and plugged 1/8" NPT tap. Locate NPT
tap within reach for test gauge hook up. NPT
tap must be upstream from stove (see Figure
11, page 13).
IMPORTANT: Install an equipment shutoff
valve in an accessible location. The equip-
ment shutoff valve is for turning on or shutting
off the gas to the appliance.

www.factorybuysdirect.com
13
200257-01A
Gas Inlet / Gas esté
INLETGAS PRESSURE MAX 1/2 PSIG (3.5 KPa)
200110-01B
03/15
WARNING:Make sure Regulator Cap is in the appropriate position
asshown in diagrams. Installation and service should be done by
qualifiedservice technician only.
Natural Gas
Whenusing natural gas:
Makesure the cap is installed in the propane/LP inlet of regulator.
Usethread sealant to assure there are no leaks.
Propane/LPGas
Whenusing propane/LP gas:
Makesure the cap is installed in the natural gas (NG) inlet of regulator.
Usethread sealant to assure there are no leaks.
ADVERTENCIA:Asegúrese la tapa del regulador esté en la posición adecuada,
comose muestra en los diagramas. La instalación y reparaciones deben ser realizadas
porun técnico de servicio calificado solamente.
Gas Natural
Cuandose utiliza gas natural:
Asegúrese de que la tapa está instalado en el propano/LP entrada del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
Propano/LPGas
Cuandose utiliza el gas propano / LP:
Asegúresede que la tapa está instalado en la entrada de gas natural (GN) del regulador.
Utilice sellador de roscas para asegurar que no haya fugas.
CorrectPilot Flame Pattern
IncorrectPilot Flame Pattern
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
NG
3-3.5"WC
NaturalGas
Shown
LP
8-11"WC
1/2Glas
s
Height
1/2Glas
s
Height
Yellow
Tipping
CorrectBurner Flame Pattern
IncorrectBurner Flame Pattern
LP
BluePlunger
INSTALLSUPPLIED CAP IN FITTING
NOTBEING USED.
INSTALARTAPASUMINISTRADA MONTAJE NO SE UTILIZA.
NG
YellowPlunger
Thisappliance may be installed in an aftermarket,*
permanentlylocated, manufactured (mobile) home, where
notprohibited by local codes.
Thisappliance is only for use with propane or natural gas.
Fieldconversion by any other means including the use of
akit is not permitted.
WARNING:Make sure the supplied cap is
installedin unused regulator fitting before
connectingthe correct gas supply line.
WARNING:Do not use natural gas and
propanegas together.
CAUTION:Two gas line installations at
thesame time are prohibited.
ADVERTENCIA:Asegúrese de que la línea
noutilizado se conecta por primera vez
antesde conectar la línea de suministro
degas correcta.
ADVERTENCIA:No utilice el gas natural y
elgas propano juntos.
PRECAUCIÓN:Dos instalaciones de
líneasde gas al mismo tiempo están
prohibidos.
FORPROPANE GAS SUPPLY
PARALA FUENTE DE GAS DEL PROPANE
CAUTION:The heater requires an external regulator to reduce
theLP tank pressure to a maximum of 14" W.C. Never connect
thisproduct directly to the supply tank.
PRECAUCIÓN:El calentador requieres una externa regulador
parareducir la presión del tanque de gas a un máximo de 14"
W.C.Nunca conecte este producto directamente al tanque de
suministro.
FORNATURAL GAS SUPPLY
PARALA FUENTE DE GAS DEL NATURAL
NOTICE:An additional gas regulator will be necessary if the
localnatural gas pressure exceeds the heater's rated maximum
inletpressure. If in doubt, contact the local gas utility. If natural
gasinlet pressure exceeds 10" W.C., the safety pressure switch
willactivate. See owners manual for proper procedure to bypass
thepressure switch.
AVISO:Un regulador de gas adicional será necesario si la
presióndel gas natural local excede de entrada nominal máxima
delcalentador presión. En caso de duda, póngase en contacto
conla compañía de gas local. Si la presión de entrada de gas
naturalsupera los 10" WC, el interruptor de presión de
seguridadse activará. Consulte el manual del propietario para el
procedimientoadecuado de derivación el interruptor de presión.
ProcomHeating, Inc. U.S. Patent Information
Thisproduct may be covered by one or more of the following
UnitedStates patents:
8,915,239 8,851,065 8,764,436 8,757,202 8,757,139 8,752,541
8,568,136 8,545,216 8,517,718 8,516,878 8,506,290 8,465,277
8,317,511 8,297,968 8,281,781 8,241,034 8,235,708 8,152,515
8,011,920 7,967,006 7,967,007 7,654,820 7,730,765 7,677,236
7,607,426 7,434,447
Otherpatents pending.
TOLL-FREECustomer Care Number: 1-866-573-0674
Numerode Atención al Cliente GRATUITO:1-866-573-0674
Visitour website for more information www.usaprocom.com
Visitenuestra página web para más informacion www.usaprocom.com
INSTALLATION
Figure 10 - Gas Regulator Location and
Gas Line Access Into Stove Cabinet
Gas Inlet Regulator
Connection
For propane/LP installations, apply pipe
joint sealant lightly to male threads. This will
prevent excess sealant from going into pipe.
Excess sealant in pipe could result in clogged
stove valves.
The installer must supply an external regula-
tor. The external regulator will reduce incom-
ing gas pressure. You must reduce incoming
gas pressure to between 11" and 14" of w.c.
If you do not reduce incoming gas pressure,
stove regulator damage could occur. Install
external regulator with the vent pointing down
as shown in Figure 12. Pointing the vent down
protects it from freezing rain or sleet.
Install sediment trap in supply line as shown
in Figure 11. Place sediment trap where it is
within reach for cleaning. Place sediment trap
where trapped matter is not likely to freeze.
A sediment trap traps moisture and contami-
nants. This keeps them from going into stove
controls. If sediment trap is not installed or is
installed wrong, stove may not run properly.
Figure 11 - Gas Connection
* Purchase the optional CSA design-certied equipment
shutoff valve from your dealer (see Accessories, page 29).
Figure 12 - External Regulator
with Vent Pointing Down
External
Regulator with
Vent Pointing
Down
Propane/LP
Supply Tank
Equipment
Shutoff Valve
Ground
Joint Union
3/8" NPT
Pipe Nipple
Tee Joint
Reducer
Bushing to
1/8" NPT
1/8" NPT
Plug Tap
Test Gauge
Connection*
Sediment
Trap
Tee Joint
Pipe Nipple
Gap
3" Minimum
Natural Gas
From Gas Meter
(5" W.C.** to
9" W.C.
Pressure)
Propane/LP
From External
Regulator
(11" W.C.**
to 14" W.C.
Pressure)
WARNING:Test all gas piping
and connections for leaks after
installing or servicing. Correct
all leaks at once (see page 14).

www.factorybuysdirect.com 200257-01A
14
INSTALLATION
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping
and connections for leaks after
installing or servicing. Correct
all leaks at once.
WARNING: Never use an
open ame to check for a leak.
Apply a noncorrosive leak detec-
tion uid to all joints. If bubbles
form, there is a leak. Correct all
leaks at once.
PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM
Test Pressures In Excess Of 1/2 PSIG (3.5
kPa)
1. Disconnect stove with its appliance main
gas valve (control valve) and equipment
shutoff valve from gas supply piping sys-
tem. Pressures in excess of 1/2 PSIG will
damage stove regulator.
2. Cap off open end of gas pipe where equip-
ment shutoff valve was connected.
3. Pressurize supply piping system by either
opening propane/LP supply tank valve
for propane/LP gas or opening main gas
valve located on or near gas meter for
natural gas or using compressed air.
4. Check all joints of gas supply piping sys-
tem. Apply noncorrosive leak detection
uid to all joints. If bubbles form, there
may be a leak.
5. Correct all leaks at once.
6. Reconnect stove and equipment shutoff
valve to gas supply. Check reconnected
ttings for leaks.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Fig-
ure 13).
2. Pressurize supply piping system by either
opening propane/LP supply tank valve
for propane/LP gas or opening main gas
valve located on or near gas meter for
natural gas or using compressed air.
3. Check all joints from gas meter to equip-
ment shutoff valve for natural gas or
propane/LP supply to equipment shutoff
Figure 13 - Equipment Shutoff Valve
Open
Closed
Equipment
Shutoff Valve
Control Valve
Location
Control Valve
Location
Equipment
Shutoff Valve
Equipment Shutoff Valve
External Regulator
Propane/LP
Supply Tank
Figure 14 - Checking Gas Joints for
Propane/LP Gas
Figure 15 - Checking Gas Joints for
Natural Gas
Gas Meter
valve for propane/LP (see Figure 14 or
15). Apply a noncorrosive leak detection
uid to all joints. Bubbles forming show a
leak.
4. Correct all leaks at once.
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see Figure
13).
2. Open main gas valve located on or near
gas meter for natural gas or open pro-
pane/LP supply tank valve.
3. Make sure control knob of stove is in the
OFF position.

www.factorybuysdirect.com
15
200257-01A
INSTALLATION
4. Check all joints from equipment shutoff
valve to control valve (see Figure 14 or
15, page 14). Apply a noncorrosive leak
detection uid to all joints. Bubbles form-
ing show a leak.
5. Correct all leaks at once.
6. Light stove (see Lighting Instructions on
page 18). Check all other internal joints
for leaks.
7. Turn off stove (see To Turn Off Gas Appli-
ance, page 19).
AA
AA
AA
AAA
AAA
AA
REMOTE OFF
ON
LEARN
INSTALLING BATTERIES
CAUTION:Donot mix old and
new batteries. Do not mix alka-
line, standard (carbon - zinc), or
rechargeable (nickel - cadmium)
batteries. Do not dispose of
batteries in re, batteries may
explode or leak.
• Batteries are included.
• Remove batteries when depleted.
• Install/replace the batteries according to the
type and quantity stated in table below.
• Do not mix old and new batteries. New bat-
teries should be the same brand for best
results.
• Be sure to observe proper polarity (+/-)
when installing or replacing the batteries.
Damage due to improper battery installa-
tion may void the warranty on the product.
• For remote control systems, maximize bat-
tery life by turning off the receiver when it
is not in use.
• For long periods of non-operation, remove
batteries from all components for safety.
Component Type of Battery Qty.
Ignitor AAA 1
Remote Control AAA 2 or 3*
Remote Receiver AA 4
*Note: Quantity depends on model of remote
control.
Ignitor
Unscrew ignitor cap and install a AAA battery
with the + pointing out. Replace cap.
Figure 17 - Installing Batteries in Remote
Control and Receiver
Receiver
Remote Control
(Transmitter)
Figure 16 - Installing Battery in Ignitor
AAA
Battery
Positive
UP
Receiver and Remote Control
Batteries are required in both the Remote
Control (Transmitter) (2 AAA size) and Re-
ceiver (4 AA size) (see Figure 17).
Note: Be sure batteries are placed correctly.
Reversing the batteries can cause damage to
the receiver and remote. Replace all batteries
on a yearly basis or sooner.
Position the slide switch on the front of the
receiver box in the ON position before install-
ing batteries. Once the batteries are installed
you will hear a single beep which indicates
the batteries are charged. If you do not hear
a beep, replace with new batteries.

www.factorybuysdirect.com 200257-01A
16
INSTALLATION
It is very important to install the logs ex-
actly as instructed. Do not modify logs.
Use only logs supplied with stove. Each
log is marked with a number. This number
will help you to identify the logs when
installing. Do not place any decorative
cinders on logs or burner.
1. Remove the packing material from the
logs. The log number is marked on the
back of each log.
Refer to Figure 18 for log placement.
2. Place pins on log #1 into two slots in the
rear bracket.
3. Place pins on log #2 into slots in the middle
bracket.
4. Place pins on log #3 into slots the front
bracket.
WARNING: Failure to posi-
tion the parts in accordance
with these diagrams or failure
to use only parts specically
approved with this stove may
result in property damage or
personal injury.
CAUTION: After installation,
and periodically thereafter,
check to ensure that no ame
comes in contact with any log.
With the stove set to high, check
to see if ames contact any log. If
so, reposition logs according to
the log installation instructions
in this manual. Flames contact-
ing logs will create soot.
INSTALLING LOGS
Rear Bracket Log #1
Log #2
Log #3
Middle
Bracket
Front
Bracket
Figure 18a - Log Installation

www.factorybuysdirect.com
17
200257-01A
INSTALLATION
Log #4
Log #5
Log #6
Figure 18b - Log Installation
5. Install hole in log #4 onto pin on the left side
of log #2, with one end resting on log #3.
6. Install hole in log #5 onto pin on the right
side of log #1, with one end resting on
log #2.
7. Install hole in log #6 onto the pin on the
right side of log #3.
IMPORTANT: Make sure logs do not cover
any burner ports. It is very important to install
the logs exactly as instructed. Do not modify
logs. Use only logs supplied with stove.

www.factorybuysdirect.com 200257-01A
18
OPERATION
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
re or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around
the appliance area for gas. Be sure to
smell next to the oor because some
gas is heavier than air and will settle
on the oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the re department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualied service technician. Force or
attempted repair may result in a re or
explosion.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualied service technician to inspect
the appliance and to replace any part of
the control system and any gas control
which has been under water.
WARNING: You must operate
this stove with the door in place.
Make sure door and screen are
installed before running stove.
NOTICE: During initial operation of
new stove, burning logs will give
off a paper-burning smell. Orange
ame will also be present. Open
damper or window to vent smell.
This will only last a few hours.
1. STOP! Read the safety information above.
2. Turn handle and open stove door.
3. Make sure equipment shutoff valve is fully
open.
4. Push in control knob slightly and turn
clockwise to the OFF position (see
Figure 19).
5. Wait ve (5) minutes to clear out any gas.
Then smell for gas around stove and near
the oor. If you smell gas, STOP! Follow
"B" in the safety information above. If you
do not smell gas, go to the next step.
6. Push in control knob slightly and turn coun-
terclockwise to the PILOT position.
Press in control knob for ve (5) seconds.
Note: The rst time that the stove is op-
erated after connecting the gas supply,
the control knob should be pressed for
about thirty (30) seconds. This will allow
air to bleed from the gas system. If pilot
does not stay lit, refer to Troubleshooting,
pages 26 though 29. Also contact a quali-
ed service technician or gas supplier for
repairs. Until repairs are made, light pilot
with match.
• If control knob does not pop up when
released, contact a qualified service
technician or gas supplier for repairs.
7. With control knob pressed in, press
in and release ignitor button. This will
light pilot. The pilot is attached to the
rear of the burner. If needed, keep
pressing ignitor button until pilot lights.
LIGHTING INSTRUCTIONS
Ignitor Button
Control Knob
Figure 19 - Ignitor Button and Control
Knob Locations

www.factorybuysdirect.com
19
200257-01A
OPERATION
Figure 20 - Pilot
Note: If pilot does not stay lit, refer to
Troubleshooting, pages 26 though 29.
Also contact a qualied service technician
or gas supplier for repairs. Until repairs
are made, light pilot with match. To light
pilot with match, see Manual Lighting
Procedure.
8. Keep control knob pressed in for 30 sec-
onds after lighting pilot. After 30 seconds,
release control knob.
Note: If pilot goes out, repeat steps 4
through 8. This stove has a safety inter-
lock system. Wait one (1) minute before
lighting pilot again.
9. Be sure the slide switch on the front of the
receiver box is in the ON position.
10. Turn control knob counterclockwise
to the ON position. The main burner
should light.
Note: If burner does not light, push the
slide switch on the receiver box to the OFF
position, then back to the ON position.
Note: Please wait one minute after shut-
ting off stove to allow the control valve to
reset before starting again.
11. If stove will not operate, follow the instruc-
tions To Turn Off Gas To Appliance, and
call your service technical or gas supplier.
CAUTION: Do not try to ad-
just heating levels by using the
equipment shutoff valve.
WARNING: If input gas
type is NG, make sure NG pilot
burner ignites. If input gas type
is LP, make sure LP pilot burner
ignites.
Shutting Off Heater
Turn control knob clockwise to the
OFF position.
Shutting Off Burner Only (pilot
stays lit )
Turn control knob clockwise to the
PILOT position.
1. Turn handle and open stove door.
2. Follow steps 1 through 5 under Lighting
Instructions, page 18.
3. With control knob in PILOT position, strike
match, and hold near pilot. Press in control
knob; pilot should light.
4. Keep control knob pressed in for 30 sec-
onds after lighting pilot. After 30 seconds,
release control knob.
5. Make sure the stove door is closed before
operating stove.
TO TURN OFF GAS TO APPLIANCE
MANUAL LIGHTING PROCEDURE
(Back of pilot
shown for clarity)
Pilot Air
Inlet Hole
Natural Gas
Burner
Propane/LP
Gas Burner
Thermocouple
Pilot Air Inlet Hole
Ignitor
Electrode

www.factorybuysdirect.com 200257-01A
20
REMOTE CONTROL SYSTEM
Programming the Remote and Receiver
The remote and receiver must be “learned”
to one another.
To prepare the receiver box for learning, use
a pen or small screwdriver to gently press
and hold the learn button until you hear 3
series of beeps.
1. Place the slide switch on the receiver in
the remote position (see Figure 22).
2. Turn control knob on the stove to the ON
position.
3. Use a pen or small screwdriver to gently
press and hold the recessed LEARN
button on the face of the receiver for 2-3
seconds. You will hear a beep.
4. Press the ON button on the remote control
to light the burner (see Figure 22). You
will hear a series of beeps. This will also
"learn", or program, the remote and the
receiver.
Note: Remote must be at least 5 feet
away from the receiver during the learning
process.
Note: If the remote control is lost or dam-
aged, the slide switch on the receiver can
be used to operate the stove.
Note: When batteries are replaced the
learning process above must be repeated.
LEARN
REMOTE OFF
ON
Figure 21 - Receiver
Slide Switch
Learn Button
Key Settings
ON - Operates unit to on position, manually
operated solenoid ON.
OFF - Operates unit to off position, manually
operated solenoid OFF.
MODE - Changes unit from manual mode to
thermo mode.
SET - Sets temperature in thermo mode.
Figure 22 - Remote Control
TEMP
ROOM SET TEMP
1
4
6
2
3
5
Figure 23 - Remote Control Display
LCD Liquid Crystal Display
1. DISPLAY Indicates CURRENT room
temperature.
2. °F or °C Indicates degrees Fahrenheit or
Celsius.
3. FLAME Indicates burner/valve in operation.
4. ROOM Indicates remote is in THERMO
operation.
5. TEMP Appears during manual operation.
6. SET Appears during time the of setting
the desired temperature in the thermo
operation.
Remote Control Operation
This appliance must not be used with glass
doors in the closed position. This can lead
to pilot outages and severe sooting outside
the replace.
The transmitter operates on 2 AAA batteries.
OPERATION