Enviro 50-1221 User manual

PELLET STOVE
Mini
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE
OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY
OR EVEN DEATH
Contact your building or fire officials about restrictions and installation
inspection requirements in your area.
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
TECHNICAL MANUAL
50-1221

2
Introduction...................................................................................................................................3
Rating Label Location................................................................................................................3
Important Safety Data...............................................................................................................3
Safety Warnings And Recommendations.....................................................................................3
Installation.....................................................................................................................................5
Deciding Where to Locate your Pellet Appliance..........................................................................5
Removing Pellet Stove From Pallet.............................................................................................5
Appliance Dimensions and Specifications....................................................................................6
Hearth Pad (50-1219) Installation..............................................................................................6
Clearances to Combustibles.......................................................................................................7
Alcove Clearances.....................................................................................................................7
Vent Termination Requirements.................................................................................................8
Outside Fresh-Air Connection.....................................................................................................9
Exhaust and Intake Locations....................................................................................................9
Mobile Home Installation.........................................................................................................10
Corner Through Wall Installation..............................................................................................10
Horizontal Exhaust Through Wall Installation.............................................................................11
Through Wall With Vertical Rise and Horizontal Termination Installation - Freestanding................12
Inside Vertical Installations......................................................................................................13
Outside Vertical Installations....................................................................................................13
Hearth Mount Installation........................................................................................................14
Exterior Mounted Exhaust Blower (20-070)...............................................................................15
Typical Through Wall With Exterior Blower Kit Installation - Vertical Termination..........................17
Thermostat Installation............................................................................................................18
Optional Slider/Damper Installation..........................................................................................18
Slider/Damper Set-Up..............................................................................................................19
Optional Panel Kit....................................................................................................................20
Fan Kit Installation..................................................................................................................21
Troubleshooting............................................................................................................................22
Fuses.....................................................................................................................................24
Wiring Diagram.............................................................................................................................25
Parts List......................................................................................................................................26
Parts Diagram - Components..........................................................................................................28
Parts Diagram - Steel.....................................................................................................................29
Installation Data Sheet..................................................................................................................31
Table of Contents

3
Introduction
* This manual is designed for the technician in conjunction with the owner’s manual. *
RATING LABEL LOCATION:
The rating label is located on the inside of the ash pan cover.
IMPORTANT SAFETY DATA:
Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet
Stove. Failure to follow these instructions may result in property damage, bodily injury
or even death. Contact your local building or fire official to obtain a permit and any information on
installation restrictions and inspection requirements for your area.
To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering
to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information
with regards to your local building codes and installation restrictions.
The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive
chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash
pan and viewing door must be locked securely for proper and safe operation of the pellet stove.
Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper
combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by
adjusting the slider damper located on the left side of the stove.
When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the
home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all
construction meets local building codes.
Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an
extremely rich burn (black tipped, lazy orange flames).
If you have any questions with regard to your stove or the above-mentioned information, please feel free
to contact your local dealer for further clarification and comments.
SAFETY WARNINGS AND RECOMMENDATIONS:
Caution: Do not connect to any air distribution duct or system.
Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil.
Unit hot while in operation. Keep children, clothing and furniture away. Contact
may cause skin burns.
SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which
will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the
house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/
damper as needed to ensure proper combustion. See: “INSTALLATION SLIDER/DAMPER SETTING”.

4
Introduction
ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be
grounded. The grounded electrical cord should be connected to a standard 110-120 volts,, nominal
average 2.0 Amps (4.1 Amps peak), 60 hertz electrical outlet and also must be accessible. If this power
cord should become damaged, a replacement power cord must be purchased from a qualified ENVIRO
dealer. Be careful that the electrical cord is not trapped under the appliance and that it is clear of any hot
surfaces or sharp edges. This unit’s maximum power requirement is 184 watts (322 watts peak).
GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove
with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO
dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is
hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner,
or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the
glass.
FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter
fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from
the heater while it is in use.
SMOKE DETECTOR: Smoke detectors should be installed and maintained in the structure when
installing and operating a pellet burning appliance.
OPERATION: The ash pan and door must be closed securely for proper and safe operation of the pellet
stove. Also ensure all gaskets on the door are checked and replaced when necessary.
INSTALLATION: Be sure to maintain the structural integrity of your home when passing a vent through
walls, ceilings, or roofs. It is recommended that the unit be secured into its position in order to avoid any
displacement.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
FRESH AIR: Outside fresh air must be connected to all units installed in Mobile and “Air Tight Homes”
(R2000) or where required by local codes. Consider all large air moving devices when installing your unit
and provide room air accordingly. Outside fresh air connection is optional in all other installations. Limited
air for combustion may result in poor performance, smoking and other side effects of poor combustion.
If you have any questions with regards to your stove or the above-mentioned information, please feel
free to contact your local dealer for further clarification and comments.
SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF
YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED
FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD
INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5
Installation
DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:
1. Remove the right and left hand cabinet sides by
loosening the three (3) T-20 Torx screws on the back
of the each panel.
2. Remove the screw located on the front of the cabinet
side, below the louvers and loosen the screw behind
the ash door.
3. Using a 5/16” socket of flat head screwdriver, remove
the three (3) wood screws that are holding the
bottom of the stove to the pallet. There is one (1)
screw behind each side panel and one (1) at the back
behind the back grill.
4. Install the four (4) leveling legs into the nuts in the
base.
5. Close the side panels.
Figure 1: Screws to take out to remove stove from
pallet.
1. Check clearances to combustibles.
2. Do not obtain combustion air from an attic, garage or any unventilated space.
Combustion air may be obtained from a ventilated crawlspace.
3. Do not install the stove in a bedroom.
4. You can vent the stove through an exterior wall behind the unit or connect
it to an existing masonry or metal chimney (must be lined if the chimney is
over 6” (15 cm) diameter, or over 28 inches² (180 cm²) cross sectional area).
An interior vent can be used with approved pipe passing through the ceiling
and roof.
5. Locate the stove in a large and open room that is centrally located in the
house. This will optimize heat circulation.
6. The power cord is 8 feet (2.43 m) long and may require a grounded extension
cord to reach the nearest electrical outlet.
REMOVING PELLET STOVE FROM PALLET:

6
Installation
APPLIANCE DIMENSIONS AND SPECIFICATIONS:
Figure 2: Dimensions of Mini.
15 1/2"
(393 mm)
18 7/8"
(481 mm)
17 1/2"
(444 mm)
19 5/8"
(497 mm)
17 7/8"
(455 mm)
34"
(864 mm)
18 1/2"
(470 mm) 22 1/8"
(562 mm)
Weight (with full hopper): 238 lb (108 Kg)
Hopper Capacity: up to 48 lb (21.8 Kg)
Voltage: 110 - 120 V
Max Current: 4.1 Amps
Consumption on High: 3.1 lb/hr (1.4 Kg/hr)*
Consumption on Low: 1.3 lb/hr (0.6 Kg/hr)*
(Note: Consumption will vary with the type of
fuel used.)
HEARTH PAD (50-1219) INSTALLATION:
1. Remove the cab sides and ash pan cover.
2. Slide the hearth pad back into place until front tab
touches the base.
3. Locate the five (5) screw holes (see Figure 3) and
install #8-32 torx T-20 screws and tighten.
4. Adjust the leveling legs to level and support stove.
5. Re-install the cab sides and ash pan cover.
Figure 3: Mini Hearth Pad in Place.

7
Installation
CLEARANCES TO COMBUSTIBLES:
IMPORTANT: Attach the Mini’s Hearth Pad when installing the unit on a combustible floor. The supplied
hearth pad meet all the requirement of a proper hearth pad. If you do not use the supplied hearth pad a
hearth pad must be used when on combustible material.
ALCOVE CLEARANCES:
This unit may be installed in an alcove. Maintain these clearances to combustibles.
Minimum Alcove width 36 inches (91.5 cm)
Minimum Alcove height 48 inches (122 cm)
Maximum Alcove depth 30 inches (76 cm)
Install vent at clearances specified by
the vent manufacturer.
Side Wall
Back Wall
AdjacentWall
8"
(20cm)
3"
(7.5cm)
4" (10cm)
36"
(91.5cm)
30"
(76cm)
48"
(122cm)
If the Mini is installed on carpet the use of a solid
material must be used under leveling legs.
These dimensions are minimum clearances but
it is recommended that you ensure sufficient
room for servicing, routine cleaning and
maintenance.
Side wall to unit 8 inches (20 cm)
Back wall to unit 4 inches (10 cm)
Corner to unit 3 inches (7.5 cm)
Figure 4: Mini Clearance to Combustibles.
Figure 5: Mini Minimum Alcove Size.

fumes such as stairwells, covered breezeway, etc.
2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding
or guards may be required.
3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of
vertical pipe be installed outside when the appliance is vented directly through a wall, to create some
natural draft to prevent the possibility of smoke or odor during appliance shut down or power failure.
This will keep exhaust from causing a nuisance or hazard from exposing people or shrubs to high
temperatures. In any case, the safest and preferred venting method is to extend the vent through the
roof vertically.
4. Distance from the bottom of the termination and grade is 12” (30 cm) minimum. This is conditional
upon the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants
and shrubs located in the vicinity of termination. The grade surface must not be lawn.
5. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the
exterior of the house might occur. Since these factors are beyond the control of Sherwood Industries
Ltd, we grant no guarantee against such incidents.
NOTE: Venting terminals can not be recessed into walls or siding.
Installation
VENT TERMINATION REQUIREMENTS:
IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER.
Figure 6: Use in conjunction with Table 1 for allowable exterior vent termination locations.
Table 1: Use in conjunction with Figure 6 for allowable exterior vent termination locations.
Letter Minimum Clearance Description
A 24 in (61 cm) Above grass, top of plants, wood, or any other combustible materials.
B 48 in (122 cm) From beside/below any door or window that may be opened.
C 24 in (61 cm) From above any door or window that may be opened.
D 24 in (61 cm) To any adjacent building, fences and protruding parts of the structure.
E 24 in (61 cm) Below any eave or roof overhang
F 12 in (30 cm) To outside corner.
G 12 in (30 cm) To inside corner, combustible wall (vertical and horizontal terminations).
H 3 ft (91 cm) within a height of 15 ft (4.5
m) above the meter/regulator assembly
To each side of center line extended above natural gas or propane meter/regulator assembly or
mechanical vent.
I 3 ft (91 cm) From any forced air intake of other appliance
J 12 in (30 cm) Clearance to non-mechanical air supply inlet to building, or the combustion air inlet to any appliance.
K 24 in (61 cm) Clearance above roof line for vertical terminations.
L 7 ft (2.13 m) Clearance above paved sidewalk or paved driveway located on public property.
Air Supply Inlet Gas Meter Restriction Zone
(Termination not allowed)
Termination Cap
G
G
Opens
Opens
Opens
DF
B
B
AI
H
K
G
G
L
C
E
1. Do not terminate
the vent in any
enclosed or semi-
enclosed areas
such as a carport,
garage, attic,
crawlspace, narrow
walkway, closely
fenced area, under
a sundeck or porch,
or any location
that can build up
a concentration of
8

9
EXHAUST AND INTAKE LOCATIONS:
101/16"
(255mm)
61/8"
(156mm)
21/16"
(53mm)
Figure 8: Mini Inlet and Outlet Location.
EXHAUST
Base of unit to center of flue 10 1 / 16” (255 mm)
Center of unit to center of flue 0” (0 mm)
[at center of unit]
FRESH AIR INTAKE.
Base of unit to center of intake 6” (156 mm)
Center of unit to center of intake 21 / 16” (53 mm)
Outside fresh air is mandatory when installing
this unit in airtight homes and mobile homes.
A Fresh-air intake is strongly recommended for all
installations. Failure to install intake air may result in
improper combustion as well as the unit smoking during
power failures.
When connecting to an outside fresh air source, do not
use plastic or combustible pipe. A 2” minimum (51
mm) ID (inside diameter) steel, aluminum or copper
pipe should be used. It is recommended, when you
are installing a fresh air system, to keep the number of
bends in the pipe to a minimum.
Installation
OUTSIDE FRESH-AIR CONNECTION:
 
 




Figure 7: Outside Air Connection.

10
Figure 10: Corner Installation.
CORNER THROUGH WALL INSTALLATION:
3" (75mm)
3"
(75mm)
Wall thimble
manufactured
by pellet vent
manufacturer.
Installation
MOBILE HOME INSTALLATION:
ENVIRO Mini
1/4” Lag Bolts
Securely Fastened
Ground Wire Directly
to Metal Chassis
Optional
Hearth Pad
Flooring
Steel Frame
● Secure the heater to the floor using the
two holes in the pedestal.
● Ensure the unit is electrically
grounded to the chassis of your home
(permanently).
● Do not install in a room people sleep in.
● Outside fresh air is mandatory. Secure
outside air connections directly to fresh
air intake pipe and secure with three
(3) screws evenly spaced.
CAUTION: THE STRUCTURAL
INTEGRITY OF THE
MANUFACTURED HOME FLOOR,
WALL AND CEILING/ROOF MUST
BE MAINTAINED.
Figure 9: Mobile home installation.

Installation
HORIZONTAL EXHAUST THROUGH WALL INSTALLATION:
Vent installation: install vent at clearances specified by the vent manufacturer.
A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces,
or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and
Equipment. Only use venting of L or PL type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm).
1. Choose a location for your stove that meets
the requirements stated in this manual and
allows installation with the least amount of
interference to house framing, plumbing,
wiring, etc.
2. Install a non-combustible hearth pad
(where necessary).
3. Place the appliance 15” (37.5 cm) away
from the wall. If the stove is to be set on
a hearth pad, set the unit on it, and adjust
the leveling legs.
4. Locate the center of the exhaust pipe on
the stove. Extend that line to the wall.
Once you have located the center point on
the wall, refer to pellet vent manufacturer
installation instructions for correct hole size
and clearance to combustibles.
5. Install the wall thimble as per the
instructions written on the thimble. Maintain
11
Figure 11: Straight through wall Installation.
Non-combustible
floor protection.
Existing floor
(combustible)
6"
(15 cm)
4"
(10 cm)
Wall
thimble
Rodent
mesh cap
45°
elbow
12"
(30.5 cm)
Exhaust Tube
3" (75mm) or 4" (100mm) "PL" or "L" vent
Wall Thimble
45° Elbow with screen or
Termination Cap
High Temperature RTV
Silicone Required
Fresh Air Intake Tube
Figure 12: Venting to use with straight through wall Installation.
an effective vapour barrier in
accordance with local building
codes.
6. Install a length of 3” (75 mm)
or 4” (100 mm) vent pipe into
the wall thimble. The pipe
should install easily into the
thimble.
7. Connect the exhaust vent
pipe to the exhaust pipe on
the stove. Seal the connection
with high temperature
silicone.
8. Push the stove straight back,
leaving a minimum of 4” (10
cm) clearance from the back
of the stove to the wall. Seal
the vent pipe to the thimble
with high temperature
silicone.

12
Wall framing
Wall thimble
Termination cap
Vertical section
of vent pipe
Horizontal frame
for thimble
90° elbow
Concrete Wall
Clean out tee
Wall framing
Wall thimble
Termination cap
Vertical section of vent pipe
Horizontal frame for thimble
Clean out tee
90° elbow
Wall strap
Figure 13: Venting horizontally with rise. Figure 14: Venting with concrete wall behind unit .
Installation
9. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length
of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place
high temperature silicone around the pipe that passes through the thimble.
10. Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The
stainless steel cap termination manufactured by the vent manufacturer is recommended. However,
when the vent terminates several feet above ground level and there are no trees, plants, etc. within
several feet, a 45° elbow can be used as termination. The elbow must be turned down to prevent
rain from entering.
NOTE:
• Some horizontal through wall installations may require a “T” and 3 to 5 feet (91 to 152 cm) of vertical
pipe outside the building to help naturally draft in the unit.
• This may be required if a proper burn cannot be maintained, after the stove has been tested and the
airflow set.
• This is due to the back pressure in the exhaust caused by airflow around the structure.
• All sections of pipe must have three (3) screws evenly spaced and all horizontal and vertical vent
sections located within the house must have a bead of high temperature silicone installed on the male
end of the pipe before installation to create a gas tight seal.
THROUGH WALL WITH VERTICAL RISE AND HORIZONTAL TERMINATION INSTALLATION - FREESTANDING:
A 45° elbow with a rodent screen may be used in place of the termination cap (or stainless steel
termination hood).
Figure 13 is the recommended installation set up.
Figure 14 is the installation to use if there is a concrete or retaining wall in line with exhaust vent on
a pellet stove. The termination must be 12” (30 cm) from the outside wall and 12” (30 cm) above the
ground.

 
 
    
    
    
 
 
  
 
 
  
   
 
    
    
  
Figure 15: Inside Vertical Installation.
1. Choose a stove location that is ideal. See the
section “DECIDING WHERE TO LOCATE YOUR PELLET
APPLIANCE.”
2. Place a non-combustible hearth pad where
necessary.
3. Place the unit on the hearth pad (if installed
on a combustible surface) and space the
unit in a manner so when the pellet vent is
installed vertically, it will be 3” (7.5 cm) away
from a combustible wall.
4. Install the tee with clean out.
5. Install the pellet vent upward from there.
When you reach the ceiling, make sure
that the vent goes through the ceiling fire
stop. Maintain a 3” (7.5 cm) distance to
combustibles and keep attic insulation away
from the vent pipe. Maintain an effective
vapor barrier.
6. Finally, extend the pellet vent to go through
the roof flashing.
7. Ensure that the rain cap is approximately 24”
(600 mm) above the roof.
To accomplish a outside vertical pipe installation,
follow steps 1 through 5 in the “INSIDE VERTICAL
INSTALLATIONS - FREESTANDING” section and then finish it
by performing the following (refer to Figure 16).
1. Install a tee with clean out on the outside of the
house.
2. Install PL vent upward from the tee. Make sure
that you install support brackets to keep the vent
straight and secure.
3. Install ceiling thimble and secure the flashing as
you go through the roof.
4. Ensure that the rain cap is approximately 24”
(600 mm) above the roof.
13
Installation
INSIDE VERTICAL INSTALLATIONS:
Figure 16: Outside Vertical Installation.
OUTSIDE VERTICAL INSTALLATIONS:
Rain cap
Flashing
24"
(61 cm)
4"
(10 cm)
Tee with
cleanout
3" (7.5 cm)
Clearance
Support
bracket
Type "PL"
vent

14
Installation
HEARTH MOUNT INSTALLATION:
Rain cap
Storm collar
Seal plate (cover plate)
Existing masonry flue
Vent pipe (single wall
stainless flex pipe or
solid PL vent)
Fireplace damper
location
Clean out tee
Existing fireplace
Flexible vent connector
(use this 5 foot [152cm]
section of pipe to vent
past fireplace damper
or small shelf)
Figure 18: Freestanding hearth mount installation overview.
Refer to Figures 17 and 18.
1. Install the hearth pad.
2. Lock fireplace damper in the open position.
3. Install a positive flue connector at the
fireplace dampers or seal the chimney at
the top.
4. Connect a tee to the exhaust pipe.
5. Install flexible stainless steel liner or listed
pellet vent to the top of the chimney.


  
 
 
 
   
 
  
 
   
   
   
 
  

Flue
Connector
Figure 17: Freestanding hearth mount installation.

Installation
EXTERIOR MOUNTED EXHAUST BLOWER (20-070):
The Mini can be equipped with an externally mounted exhaust blower. This optional kit includes all
components necessary to install the exhaust blower on any vertical wall surface.
1. Remove the left hand cabinet side by removing the two
(2) screws down the front. Loosen the three screws on the
back of the cabinet side and remove panel.
2. Loosen the six (6) screws that hold the back grill in place.
Lift the back grill off the screws.
3. Disconnect the Exhaust blower wires from the wire
harness. Remove the exhaust blower motor from the
housing; six (6) screws. Cover hole in housing with cover
plate provided (see Figure 20).
4. Remove the cover from the exhaust blower housing box.
5. Install the exhaust blower housing box into the pipe placed
through the wall thimble, seal with high temperature
silicone. Fasten the box to the wall with (4) four screws,
seal edges of box to wall with clear silicone.
6. Drill a hole through the wall thimble plate for the electrical
wires. Pass the armored cable through the wall thimble.
Use the strain relief provided. Do not pass cable
through vent hole.
7. Install the Exhaust Blower motor into the external exhaust
blower housing box. Make the electrical connections to the
wire harness and exhaust blower.
8. Replace the cover on the Exhaust Box and the back grill of
the stove and ensure the screws are tightened down.
9. Install vertical pipe as instructed in appropriate section.
Choose a location for your stove that meets the requirements
stated in your manual and allows installation with the least
amount of interference with house framing, plumbing,
wiring, etc.
Included in the Exterior Mounted Exhaust Blower Kit are:
1 - Exhaust blower housing box.
1 - Blower cover plate.
1 - Hardware bag
Figure 19: Exterior Blower Kit.
Figure 20: Exterior Blower Kit.
Figure 21: Exterior Blower Kit cut-through.
15

Installation
TYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - HORIZONTAL TERMINATION:
Electrical Cable
90° Elbow
45°Elbow with Rodent
screen or stainless
steel termination hood
2ft (610mm) Riser
Pipe Adaptor
Exterior Blower
and Housing
Wall Strap
To supply power to
the exhaust blower
Install the amour coated electrical cable from the exhaust blower housing, through the wall thimble plate
and attach to the pre drilled hole in the left hand rear hopper pillar. Hook up to wires from the exhaust
blower wiring harness.
All electrical connections must be in accordance to local code requirements
NOTE:
Ensure that all interior vent connections are sealed by placing a small bead of high temperature silicone
around each chimney connection.
Also ensure that all vertical vent sections are properly supported and that all clearances to combustibles
are maintained in accordance with the vent manufacturer’s specifications.
Figure 22: Through Wall Installation with Exterior Blower Kit.
Figure 23: Through Wall Installation with Exterior Blower Kit; Side View.
16

17
Roof Sheathing
Rain Cap
Roof Flashing
Roof Rafters
Ceiling Joists
Vent Pipe
Exterior Wall
Sheathing
Outside Vent
Termination
Installation
TYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - VERTICAL TERMINATION:
Follow the previous pages for through wall installations. Ensure that vent pipe is properly secured to wall
using wall straps. Maintain clearances to combustibles on vent pipe as well as unit.
Figure 24: Through Wall Installation with Exterior Blower Kit; Vertical Termination.

Installation
THERMOSTAT INSTALLATION:
If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the
thermostat is not calling for heat. When the thermostat calls for heat, the unit will go to the setting that
is displayed on the control board Heat Indicator. If the heating load is not great enough when the stove
is on low, the high limit switch will turn the stove off and the switch will have to be manually reset. To
reset the high limit switch, remove the right cabinet side. The switch is found behind the control panel.
Avoid setting off the high limit switch.
OPTIONAL SLIDER/DAMPER INSTALLATION:
A) HI / LOW:
When the jumper is placed
on only one of the J9 pins,
then the control board is in a
HI / LOW mode of thermostat
operation (factory setting).
B) ON / OFF:
If both pins of J9 are jumped
(covered), the control board
is in an ON / OFF mode of
thermostat operation.
Thermostat wires.
Figure 25: Circuit Board.
This control board can be placed into two
different modes: When the jumper J9 is
not jumped then the control board is in a
HI / LOW mode operation. If the control
board is placed with J9 jumped then the
control board is in a ON / OFF mode of
operation. In the ON /OFF thermostat
mode, the unit will shut OFF when the
thermostat is not calling for heat. When
the thermostat calls for heat, the unit will
go through an ignition sequence once
again and relight.
1. Install the wall thermostat in a location
that is not to close too the unit but will
effectively heat the desired area.
2. Install a 12 or 24 Volt Thermostat using
an 18 x 2 gauge wire from the unit to
the thermostat.
Slider damper
rod and knob
7/16" Nut
7/16" Clinching Nut
Slider damper plate
1. To install the OPTIONAL slider damper rod, remove the left
cabinet side and locate the slider damper plate. Install the 7/16”
inch nut onto the slider damper rod, thread all the way to the
end of the threads on rod.
2. Slide rod through the hole in the slider damper plate and install
the 7/16” clinching nut onto the rod and tighten completely onto
the slider damper plate.
3. Re-install the cabinet side. Install the black knob on the end of
the rod. Check slider damper for smooth operation.
Slider/Damper
Knob
If you wish to adjust the slider damper externally
(NOT REQUIRED), please follow the instructions
below.
Figure 26: Slider/Damper Assembly.
Figure 27: Slider/Damper Knob.
18

19
If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the
Slider Damper should be pushed in slightly, decreasing the air in the firebox.
If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of
clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider
damper must be pulled out to compensate. Pulling the slider damper out gives the fire more air.
The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of
the fire.
• A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly.
• A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.
• If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame
with no black tips then the air is set for proper operation.
SPECIAL NOTES:
Pellet quality is a major factor in how the Pellet stove will operate. If the pellets have a high moisture
content or ash content the fire will be less efficient and has a higher possibility of the fire building up and
creating clinkers (hard ash build-up).
IMPORTANT: Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge should
be used to set the slider for best combustion. The best settings are a reading of approximately
0.11 - 0.12 inches of water column (27 - 30 Pa) on the high fire setting. Some fuels may
require higher or lower settings. The reading can be taken from the ” (3 mm) hole located on the
front of the unit below the ash shelf.
Installation
SLIDER/DAMPER SET-UP:
This is used to regulate the airflow through the pellet stove. The slider damper should be set by a trained
technician using magnehelic.
Air Intake Box
Exhaust Channel
Slider Damper
Exhaust Blower
Figure 28: Slider/Damper Plate in Unit.
The slider damper is located
behind the left side panel. To
open the left side panel, undo the
one screw located in the upper
front corner of the cabinet side
between the louvers. Also loosen
three screws down the back of
the side panel.
The combustion exhaust blower is
a variable speed blower controlled
by the heat output button. This
blower will decrease the vacuum
pressure inside the stove and as
the heat output button is turned
down. The vacuum pressure
inside the firebox will increase as
the combustion exhaust blower
increases in speed (higher heat
output setting).

Installation
OPTIONAL PANEL KIT:
This kit must be installed before the unit is started.
20
Figure 31: Screws at back of the cab side.
Figure 29: Screws above door top corner.
Figure 30: Screw behind ash box.
Tools Required:
●T-20 screwdriver
Kit Components:
Quantity Description
1Left Cab Panel
1Right Cab Panel
1 Hopper Lid
20 #8 T-20 screws (” long)
2 Hopper Bracket
2 Bushing ” O.D. x ” long
Please ensure that all components are supplied with this kit.
If components are missing or have been damaged, contact
your dealer, distributor or courier company before starting this
installation.
Installing the Panels:
1. Remove the screws above the door on both sides (Figure
29).
2. Ensure the screws behind the ash box, one on each side
(Figure 30) and the three (3) on each side at the back
(Figure 31) are loosened.
3. Slide the three (3) slots at the back of the cab panels
under the three (3) screws at the back.
4. Optional for Left Side: Line up the slider rod with the hole
in the cab panels, slide it through, and install the knob.
5. Slide the front of the cab panels over the screw behind
the ash box.
6. Install the screw above the door and tighten all screws.