E-Tech SET-1310 Parts list manual

1 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
TECHNICAL DESCRIPTION
SET-1310
32 Channel Isolated Digital Input, 3.3 V to 60 V.
This document 9040TDD1010 is a technical description of the SET-1310.
Note Before you begin, complete the software and hardware installation procedures
applicable to your application.
Note The guidelines in this document are specific to the SET-1310. The other components in
the system might not meet the same safety ratings. Refer to the documentation of each com-
ponent in the system to determine the safety and EMC ratings for the entire system.
MORE INFORMATION ON OUR WEBSITE:
www.smart-e-tech.de/slsc

2 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
Safety Guidelines
Caution Do not operate the SET-1310 in a manner not specified in this document. Product
misuse can result in a hazard. You can compromise the safety protection built into the product
if the product is damaged in any way. If the product is damaged, return it for repair.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for electromagnetic
compatibility (EMC). These requirements and limits provide reasonable protection against harmful
interference when the product is operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may occur in
some installations, when the product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize interference with radio and television
reception and prevent unacceptable performance degradation, install, and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by SET GmbH could
void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, operate this product only with shielded
cables and accessories.
Caution To ensure the specified EMC performance, the length of any cable attached to
connectors J1 and J2 must be no longer than 3 m (10 ft.)

3 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
Description
The SET-1310 device is an isolated digital input interface for NI-SLSC. This card provides 32 optically
isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input
voltage range. It allows you to break ground loops and protect your system from high voltage spikes,
but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-
channel isolation allows to connect signals from different DUTs to a single acquisition system.
The digital inputs feature a wide supply voltage range and can be used with a variety of signal levels,
including 12 V and 28 V discrete signals.
The high-speed, high sensitivity optoisolators allow reliable input detection with an input current as low
as 6 mA. To protect the optoisolators, each input contains a current limiting circuit which limits the input
current to 6 mA over the entire input voltage range.
With a maximum voltage channel to channel and channels to chassis of 60 Vdc, SET-1310 allows you to
connect multiple DUTs operating at most usual logic levels to a single data acquisition system.
Circuitry
Note
Diagram only shows one channel.
All voltages are relative to DGND unless otherwise noted.
Note
You can configure the power-on configuration in the software. The factory
default power-on configuration sets the front I/O Channels to sinking input and
rear I/O channels to output.

4 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
15
30
44 14
29
43 13
28
42 12
27
41 11
26
40 10
25
39 9
24
38 8
23
37 7
22
36 6
21
35 5
20
34 4
J1, J2 Pinout (Front)
J1 J2
Signal
Description
Px.y
Line y in Port x
NC
No connection
DGND
Ground connection
DNC
Do not connect
J1, J2 Connector Pin Assignments
15
30
44
14
29
43
13
28
42
12
27
41
11
26
40
10
25
39
9
24
38
8
23
37
7
22
36
6
21
35
5
20
34
4
19
33
3
18
32
2
17
31
1
16
P3.2+
P3.2-
P3.1+
P3.1-
P3.0+
P3.0-
NC
DNC
P2.2+
P2.2-
P2.1+
P2.1-
P2.0+
P2.0-
NC
NC
P1.2+
P1.2-
P1.1+
P1.1-
P1.0+
P1.0-
NC
DNC
P0.2+
P0.2-
P0.1+
P0.1-
P0.0+
P0.0-
P3.3+
P3.3-
DGND
DGND
P2.3+
P2.3-
NC
NC
P1.3+
P1.3-
DGND
DGND
P0.3+
P0.3-
15
30
44
14
29
43
13
28
42
12
27
41
11
26
40
10
25
39
9
24
38
8
23
37
7
22
36
6
21
35
5
20
34
4
19
33
3
18
32
2
17
31
1
16
P7.2+
P7.2-
P7.1+
P7.1-
P7.0+
P7.0-
NC
DNC
P6.2+
P6.2-
P6.1+
P6.1-
P6.0+
P6.0-
NC
NC
P5.2+
P5.2-
P5.1+
P5.1-
P5.0+
P5.0-
NC
DNC
P4.2+
P4.2-
P4.1+
P4.1-
P4.0+
P4.0-
P7.3+
P7.3-
DGND
DGND
P6.3+
P6.3-
NC
NC
P5.3+
P5.3-
DGND
DGND
P4.3+
P4.3-

5 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
J1
XJ2
J2
XJ2
P0.0 +
DO0
P4.0 +
DO16
P0.0 -
P4.0 -
P0.1+
DO1
P4.1+
DO17
P0.1 -
P4.1 -
P0.2 +
DO2
P4.2 +
DO18
P0.2 -
P4.2 -
P0.3 +
DO3
P4.3 +
DO19
P0.3 -
P4.3 -
P1.0 +
DO4
P5.0 +
DO20
P1.0 -
P5.0 -
P1.1 +
DO5
P5.1 +
DO21
P1.1 -
P5.1 -
P1.2 +
DO6
P5.2 +
DO22
P1.2 -
P5.2 -
P1.3 +
DO7
P5.3 +
DO23
P1.3 -
P5.3 -
P2.0 +
DO8
P6.0 +
DO24
P2.0 -
P6.0 -
P2.1 +
DO9
P6.1 +
DO25
P2.1 -
P6.1 -
P2.2 +
DO10
P6.2 +
DO26
P2.2 -
P6.2 -
P2.3 +
DO11
P6.3 +
DO27
P2.3 -
P6.3 -
P3.0 +
DO12
P7.0 +
DO28
P3.0 -
P7.0 -
P3.1 +
DO13
P7.1 +
DO29
P 3.1-
P 7.1-
P3.2+
DO14
P7.2+
DO30
P3.2-
P7.2-
P3.3+
DO15
P7.3+
DO31
P3.3-
P7.3-
Front Panel Signal Descriptions

6 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
XJ2 Connector Pinout (Rear)

7 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
Row
e
d
c
b
a
1
DO 0
DO 1
NC
DO 2
DO 3
2
DO 4
DO 5
NC
DO 6
DO 7
3
DGND
DGND
DGND
DGND
DGND
4
DO 8
DO 9
NC
DO 10
DO 11
5
DO 12
DO 13
NC
DO 14
DO 15
6
DGND
DGND
DGND
DGND
DGND
7
DO 16
DO 17
NC
DO 18
DO 19
8
DO 20
DO 21
NC
DO 22
DO 23
9
DGND
DGND
DGND
DGND
DGND
10
DO 24
DO 25
NC
DO 26
DO 27
11
DO 28
DO 29
NC
DO 30
DO 31
15
NC
NC
NC
NC
NC
16
NC
NC
NC
NC
NC
17
DGND
DGND
DGND
DGND
DGND
18
NC
NC
NC
NC
NC
19
NC
NC
NC
NC
NC
20
DGND
DGND
DGND
DGND
DGND
21
NC
NC
NC
NC
NC
22
NC
NC
NC
NC
NC
23
DGND
DGND
DGND
DGND
DGND
24
NC
NC
NC
NC
NC
25
NC
NC
NC
NC
NC
XJ2 Connector Pin Assignments
Signal
Description
DO
Digital output signal connection
GND
Ground connection
NC
No connection
XJ2 Connector Signal Descriptions

8 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
LED Behavior
LED Name
LED Behavior
Definition of Behavior
PWR
Off
No power present on the board
Solid green
Power good state
RDY
Off
Module card is unpowered
Solid green
Card is recognized by the chassis and ready to communicate
Solid amber
Module card is booting
Blinking amber
Chassis is communicating with the module card
Error Handling
LED Name
LED Behavior
Actions
PWR
Off
-Check the power supply of the chassis.
-Check the external power supply if used.
RDY
Blinking Red
-Switch off and switch on the power supply (power cycle).
-Please contact the support.

9 of 9
www.smart-e-tech.com
SET-1310
Technical Description
Issue 02 13/04/2022
Hardware Specifications
Absolute Maximum Ratings
Property
Condition
Value
Comment
Max. Input Voltage
Any Pin
60 Vdc
Min. Input Voltage
Any Pin
-60 Vdc
Channel to Channel
120 Vdc
Channels to Chassis
60 Vdc
Technical Data
Property
Condition
Value
Comment
Max. Input Voltage
60 V
Overall temp. range
Min. High Level
Input Voltage
2.3 V
Input Current
VIN > 5 V
4 mA ± 2 mA
Max. Input Frequency
Square wave, 0 V to 10 V
40 kHz
Propagation Delay
Any Channel, Rising Edge
Typ: 2.7 µs
Max: 3.6 µs
Overall temp. range
Any Channel, Falling Edge
Typ: 8.4 µs
Max: 12,5 µs
Overall temp. range