EarthQuake 2B-ST35M User manual

Earthquake warrants the original purchaser that all Factory Sealed New Audio Products be free
from defects in material and workmanship, under normal and proper use, for a period of ninety (90)
days from the date of purchase (as shown on the original sales receipt with serial number
affixed/written on it). The ninety (90) day warranty period is valid only if an authorized Earthquake
dealer properly installs the product, and the warranty registration card is properly filled out and sent
to Earthquake Sound Corporation. If a non-authorized party installs the product, no warranty will be
rewarded.
(A) Ninety (90) day limited warranty guidelines:
Earthquake pays for labor, parts, and ground freight (US mainland only) back to customer.
(B) Warning:
Products (sent for repair) that are tested by Earthquake technicians and deemed to have no
problem(s) will not be covered by the day limited warranty. Customer will be charged a
minimum of one (1) hour of labor (ongoing rates) plus shipping charges back to
customer.
(C) Earthquake agrees to repair or replace - at our option - all such defective products/parts
subject to the following provisions:
Defective products/parts have not been altered or repaired by other than an Earthquake
factory approved technician.
Products/parts are not subjected to negligence, misuse, improper use, or accident, damaged
by improper line voltage, used with incompatible products, or have its serial number or any
part of it altered, defaced or removed, or have been used in any way that is contrary to
Earthquake's written instructions.
(D) Warranty Limitations:
Earthquake warranty does not cover products that have been modified or abused, including but
not limited to the following:
Damages due to misuse, abuse, or use of improper use of cleaning materials/methods.
Bent frame, broken joints, broken knobs
Fading, deterioration of speaker components & finish due to improper exposure to elements.
Subsequent damage to and from other products.
A warranty claim will not be valid if the warranty registration card is not properly filled & returned
to Earthquake with a copy of the sales invoice.
(E) Service Request:
To receive product(s) service, contact Earthquake Sound’s service department at (510) 732-
1000 and request an RMA number (Return Material Authorization) as item(s) shipped without
a valid RMA number will be refused. Make sure you provide us with your complete and correct
shipping address, a valid phone number, and a brief description of the problem you are
experiencing with the product. In most cases, our technicians might be able to resolve the
problem over the phone, thus eliminating the need to ship the product.
(F) Shipping Instructions:
Product(s) must be packaged in its original protective box(es) to minimize transport damage.
Shipper claims regarding items damaged in transit must be presented to carrier. Earthquake
Sound Corporation reserves the right to refuse product that improperly packed. Original
sales receipt must accompany product returned for service. Ship product to: Earthquake
Sound Corp. 2727 Mc Cone Avenue, Hayward, CA 94545.
You are responsible for the cost of shipping the product to Earthquake Sound Corporation.
(G) Disputes Resolution:
All disputes - between clients and Earthquake Sound Corporation - resulting from the ninety
(90) day limited warranty policy must be resolved according to the laws & regulations of the
county of Alameda, California.
2B-ST35M
Owner’s Manual
Earthquake Sound Corporation
2727 McCone Avenue. Hayward, CA 94545.USA
US Toll Free: 1-800-576-7944 | Tel: [phone] | Fax: [phone]
www.earthquakesound.com
The Sound That Will Move You

CARE & SAFETY INSTRUCTIONS
Occasionally clean the speaker stand with damp cloth or
non-abrasive cleaner.
Install the speaker ONLY when the stand/tripod is in a fully
upright position with all legs on the floor.
Do not lubricate or use silicone spray on the center tube.
Do not drag the speaker stand/tripod while it is loaded as
this may cause damage to the fittings and the stand itself.
Before placing the speaker, make sure that the telescoping
collar is securely tightened and the safety pin is fully
inserted into the slot on the upper telescoping tube.
Always practice caution when releasing the collar and stand
clear of speaker.
SPECIFICATIONS
Height Adjustment
Load Capacity
Upper Tubing Diameter
Material
43 5/8” - 73 5/8”
1100 - 1900mm
132 lbs. 4 oz.
60kgs
1 3/8”
35mm
Steel tubing with
Metal collars
SETUP INSTRUCTIONS
STEP 1
Loosen leg fitting hand knob.
STEP 2
Spread the tripod legs to maximum
diameter of leg spread then retighten
the leg fitting hand knob.
STEP 3
Remove safety pin from upper
telescoping tube slot. Loosen hand
knob on telescoping collar and raise
center tube about 6 to 10 inches.
Retighten the hand knob.
STEP 4
Put speaker cabinet on top. Slowly
loosen the hand knob and raise the
cabinet to desired height. Tighten the
hand knob and insert the safety pin
into the slot on the telescoping tube.
STEP 5
To remove the speaker, remove the
safety pin from the slot. Slowly loose
the hand knob. Carefully and slowly
lower the upper telescoping tube.
Tighten the hand knob before
removing the speaker from stand.
CAUTION:
DO NOT over tighten the hand knob.
DO NOT store in tightly locked
position.
specifications are subject to change without notice www.earthquakesound.com