Ergo EI6122 User manual

Full motion TV Wall Mount
Instruction Manual V1.0
Model: EI6122
Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE
we strive to provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to contact at
[email protected](US/CA)

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
our customer service at [email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete block
and brick walls - DO NOT install into drywall alone. Please note: When installing
into a recreational vehicle, please consult with your manufacture to determine
the correct screw depth to use for your installation.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
• Before drilling check your wall thickness to prevent damage to your recreational
vehicle.
Minimum VESA pattern: 100mm/4 in.(W)x100mm/4 in.(H)
100 mm ≈ 4 in.
75 mm ≈ 3 in.
200 mm ≈ 7 7/8 in.
MAX:200mm/8 in.
MAX:200mm/8 in.
Check the VESA Pattern of Your TV before the Installation
IMPORTANT SAFETY INFORMATION
If your TV VESA is greater than 200x200 mm/16x16 in. or less than VESA
75x75mm/3x3in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
CAUTION
Verify Your Wall Construction
If you are not sure the wall
construction, please contact
our customer service at
[email protected]
Wood Wall
Wood Studs
(with Drywall)
Solid Concrete
or Concrete Block
DO NOT
install into drywall
alone
01

01
TV Mount
Spacers [If needed]Washers
[TV1] x4
M4/M5
[TV2] x4
M6/M8
Note: The washers and spacers are shown in accordance with the actual size
Warning:This product contains small items that could be a choking hazard if
swallowed.Before starting assembly, verify all parts are included and undamaged.
Do not use damaged or defective parts. lf you require replacement parts, contact
our customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Awl
Stud Finder Tape Measure Pencil Drill
5/32 in.(4mm)
Wood Drill
Phillips
Screwdriver
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
02 03
Hammer
5/16 in. (8mm)
Concrete Drill
5/16 in. (8mm)
Socket Wrench
[TV3] x8
φ8.5x18x2.5mm
[TV4] x4
φ8.5x18x10mm
02

x1
Level
Note: The lag screw is shown in accordance with the actual size
Washer
D6
A2
x5
[Only one bolt size fits your TV]
TV Bolts
M4 x 15mm
[TV6] x4
M5 x 15mm
[TV7] x4
M6x 15mm
[TV8] x4
M8 x 20mm
[TV9] x4
M5
M4
M6
Note: The bolts are shown in accordance with the actual size
Supplied Parts for Step 2
04
Lag Screw
ST6.3x45mm
x5
A1
M8
Wall
Anchor
M8X40mm
x5
A3
This anchor is for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
03

Step 1 Unlock Arm & Detach Faceplate
Pull the strap down to
unlock the arm
Cable Tie x1
Wrench
[TV5] x1
Remove the preassembled bolt [S1] using the
wrench [TV5] or phiillips screwdriver (not includ-
ed) and loosen bolt [S2] a little to separate the
faceplate [01B] from the arm assembly/wall
plate [01A]. Keep bolt [S1] for use in Step 4. or
Supplied Parts for Step 4-6
04
S2
S1

Select TV Bolts
M6
M4 M8
Only one bolt size fits your TV.
Step 1 Secure the Faceplate [01B] to TV
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Too Short Too Long Correct Correct
M5
01A
01B
TV5
05
01A
or
S1

Option A (For Flat Back TV)
TV6/TV7/TV8/TV9
TV1/TV2
TV3
(If needed)
Option B (For Round Back TV)
TV6/TV7/TV8/TV9
TV1/TV2
TV3/TV4
For VESA hole pattern:
3 in.X3 in./75 mmX75 mm
4 in.X4 in./100 mmX100 mm
8 in.X4 in./200 mmX100 mm
8 in.X8 in./200 mmX200 mm
01B
100mm
200mm
75mm
100mm 200mm
75mm
UP
06
Alternate
Spacer
Setups
Alternate
Spacer
Setups
CAUTION: Ensure the faceplate
[01B] is EQUALLY CENTERED on
your TV and securely fastened in
place.

Step 3 Attach the Arm Assembly/Wall Plate [01A] to Wall
Position the arm assembly/wall
plate [01A] at your desired
height, level the wall plate and
mark the pilot hole locations.
3A-1
For wood wall installation, follow STEP 3A
For wood stud installation, follow STEP 3B
For concrete installation, follow STEP 3C
Step 3A Wood Wall Option
UP
Before Drilling check your wall thickness to prevent damage to your recreational
vehicle.
Wall
Anchor
A3
X
WARNING:
Ensure the arm assembly/wall plate [01A] is securely fastened to
the wall before continuing to the next step.
Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled
firmly against the arm assembly/wall plate [01A].
07
DO NOT USE ANCHOR WITH THIS STEP!

5/16in.(8mm)
Socket Wrench
(Not lncluded)
HEAVY! You may need
assistance with this step.
3A-2
ø5/32 in.(4 mm)
1 3/4 in.(45mm)
Drill 5 pilot holes using a 5/32
in.(4 mm) diameter drill bit.
Make sure the depth is not less
than 1 3/4 in.(45mm).
3A-3
Install the arm assembly/wall
plate [01] using lag screws [A1]
and washers [A2]. Tighten the
lag screws [A1] until the wash-
ers [A2] are pulled firmly
against the arm assembly/wall
plate [01A].
UP
Note: The depth of the pilot
holes shown above are for
wood wall applications. For RV
applications please use caution
and check your wall depth and
consult with your RV manufac-
ture.
A1
A2
08

Step 3B Wood Stud Option
WARNING:
Ensure the arm assembly/wall plate [01A] is securely fastened to
the wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1.5 x 3.5 in. (38 x 89 mm)
● Stud center must be verified
Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against
the arm assembly/wall plate [01A].
Use a stud finder(not included)
to locate wood studs or use
an awl (not included) to verify
the edges. Mark the edge and
center locations.
awl
(not included)
3B-1
Position the arm assembly/
wall plate [01A] at your
desired height and line up
the holes with your stud
center line. Level the arm
assembly/wall plate [01A]
and mark the holes.
3B-2
ø5/32 in.(4 mm)
1 3/4 in.(45mm)
Drill 3 pilot holes using a 5/32 in.
(4mm) diameter drill bit. Make sure
the depth is not less than 1 3/4 in.
(45mm).
3B-3
UP
Wall
Anchor
A3
X
09

● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Step 4
5/16in.(8mm)
Socket Wrench
(Not lncluded)
A1
01
HEAVY! You may need
assistance with this step.
3B-4
UP
Step 3C Solid Concrete or Concrete Block Option
Install the arm assembly/wall plate [01A]
using lag screws [A1] and washers [A2].
Tighten the lag screws [A1] until the
washers [A2] are pulled firmly against the
arm assembly/wall plate [01A].
WARNING:
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly
against the wall plate.
●Ensure the arm assembly/wall plate [01A] is securely fastened to
the wall before continuing to the next step.
Wall
Anchor
A3
Position the arm assembly/ wall
plate [01A] at your desired
height, level the wall plate and
mark the pilot hole locations.
3C-1 3C-2
ø3/8 in.(10mm)
2 in.(50mm)
Drill 5 pilot holes.Use
the hammer to knock
anchors [A3] into the
wall.
A3
A2
10

Step 4
Hang the TV onto the Arm Assembly/Wall Plate [01A]
5/16in.(8mm)
Socket Wrench
(Not lncluded)
3C-3
HEAVY! You may need
assistance with this step.
Phillips
Screwdriver
(Not lncluded)
4-1 Hang the TV to the arm assembly/wall plate [01A], making sure the upper
bolt hangs on the hook on the arm assembly/wall plate [01A].
4-2 Tighten the bolt [S1] to secure the TV to the arm assembly/wall plate [01A].
4-3 Tighten the bolt [S2].
Step 4
4-1
4-2
S1
A1
01
Install the arm assembly/wall plate [01A]
using lag screws [A1], washers [A2] and
anchors [A3]. Tighten the lag screws [A1]
only until the washers [A2] are pulled
firmly against the arm assembly/wall
plate [01A] . DO NOT over-tighten the
lag screws [A1].
UP
A2
or
TV5
11
S2
4-3

1. Slightly loosen bolt [S1] a little.
2. Adjust TV to your desired
level angle.
3. Retighten bolt [S1] to hold TV in
place.
Step 5 Adjust the Level and Tilt Angle
5-1 Level Adjustment
If needed, the TV can be levelled
Phillips
Screwdriver
(Not included)
S1
5-2 Tilt Adjustment
1. Slightly loosen four tilt nuts [T].
2. Adjust TV to your desired tilt angle.
3. Retighten four tilt nuts [T] to fix the
tilt angle.
T
Tighten
Loosen
Tighten
Loosen
TV5
or
TV5
12

Step 6 Lock the Arm to Wall Plate
Step 7 Manage the Cables
13

Thank you again for
choosing this ERGO-INNOVATE product!
All of us at ERGO-INNOVATE do appreciate your product purchase. We hope
that you are as happy with your product as we are designing and manufacturing
it for you. We strive to provide you with the best quality products and services in
the industry. Should you have any issues, please don't hesitate to contact us at
[email protected](US/CA)