Ecolibrium Solar EcoFoot5D User manual

Sales: 740-249-1877
[e-mail]
Field Support: 866-488-6794
[e-mail]
www.ecolibriumsolar.com
Installation Guide
Installation Guide
EcoFoot5D™ High Density 5-Degree Ballasted Racking System
Document No. ES10560
Rev 1.1, January 2018

EcoFoot5D Install Guide V1.1-FINAL Page 2 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Revision History
Revision
Description of Changes
Date
1.0
Initial EcoFoot5D
TM
Release
2017-September-05
1.1
Add Attachment Appendix B
2018-January-25

EcoFoot5D Install Guide V1.1-FINAL Page 3 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Table of Contents
Revision History..................................................................................................................................... 2
Table of Contents .................................................................................................................................. 3
Introduction ............................................................................................................................................ 4
Field Support Contact Information.................................................................................................... 4
Installer Responsibility.......................................................................................................................... 4
Disclaimer of Liability ........................................................................................................................... 4
Warnings & Safety................................................................................................................................. 5
EcoFoot5D General Application Notes ............................................................................................ 5
EcoFoot5D Core Components............................................................................................................ 7
Install EcoFoot5D in 6 Simple Steps.................................................................................................. 8
Appendix A: Grounding & Bonding.................................................................................................. 11
Appendix B: Roof Attachment Methods ........................................................................................12
Legal Notices
©2017 Ecolibrium Solar®, Inc. Ecolibrium Solar® and EcoFoot2+® are registered trademarks of Ecolibrium
Solar, Inc. EcoFoot5D™ is a trademark of Ecolibrium Solar, Inc., registration pending.

EcoFoot5D Install Guide V1.1-FINAL Page 4 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Introduction
EcoFoot5DTM is a 5-degree ballasted racking system designed to fit more modules on a roof, maximizing power
density. The modular design is built on the proven, industry-preferred, beautifully simple and fast-to-install
modular technology of the EcoFoot platform and sister product, EcoFoot2+.
EcoFoot5D consists of five simple components. Installation is accomplished in six simple steps. Much of the
installation is tool-less.
EcoFoot5D Bases self-align, requiring only two chalk lines. The PV module installation automatically moves the
Bases into perfect placement. Inter-row ballast placement and easy-reach wire management provide superior
accessibility during and after installation.
Stackable Bases enable the transport of up to 290kW of Bases on 1 standard pallet, streamlining logistics. The
combined effect of simplicity, maximum density, and minimized shipping, storage and transporting costs results
in an ultra cost-effective racking solution.
Field Support Contact Information
Ecolibrium Solar proudly offers dedicated engineering expertise and superior customer support. For questions
about the installation procedures or a specific application, please contact our Field Support Specialists at 866-
488-6794 or [e-mail].
Installer Responsibility
The installer is solely responsible for:
•Utilizing all necessary safety equipment, as required by applicable rules and regulations.
•Complying with all applicable local and national building codes, including any that may supersede this
manual.
•Ensuring that Ecolibrium Solar® EcoFoot5DTM and other products are appropriate for the specific
installation and are designed for the installation environment.
•Ensuring that the roof, its rafters, connections, and other structural support members can support the
array under all conditions.
•Maintaining the waterproof integrity of the roof including selection of appropriate flashing if the
system is being installed using attachments.
•Ensuring safe installation of all electrical aspects of the entire system
Disclaimer of Liability
ECOLIBRIUM SOLAR® does not assume responsibility and expressly disclaims liability for loss, damage, or
expense arising out of, or in any way connected with installation, operation, use, or maintenance by using this
manual.
ECOLIBRIUM SOLAR assumes no responsibility for any infringement of patents or other rights of third parties,
which may result from use of modules. No license is granted by implication or under any patent or patent rights.
The information in this manual is believed to be reliable, but does not constitute an expressed and/or implied
warranty.
ECOLIBRIUM SOLAR reserves the right to make changes to the product, specifications, data sheets and this
manual without prior notice. This document is not prescriptive regarding safety and does not purport to
address all the safety concerns that may arise with its use. Contractors should become familiar with all
applicable safety, health, and regulatory requirements before beginning work.

EcoFoot5D Install Guide V1.1-FINAL Page 5 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Unauthorized field modification of ECOLIBRIUM SOLAR components or assemblies may affect ECOLIBRIUM
SOLAR warranty coverage. Provide written drawings for ECOLIBRIUM SOLAR’s review, comment and
approval prior to attempting any field modifications.
Warnings & Safety
Both electrical and roofing knowledge are required to correctly and safely install a solar photovoltaic system.
Only qualified and certified installation professionals should install EcoFoot5D. Failure to follow the methods
and procedures outlined in this guide may result in injury and/or damage to property.
Carefully read this guide before starting any work. Store a copy of this guide on the job site at all times and
contact Ecolibrium Solar with any installation questions related to EcoFoot5D.
Please note the following warnings when installing EcoFooot5D:
•EcoFoot5D components fit together tightly and could cause pinch injuries.
•EcoFoot5D components may be hot to the touch if left in the sun.
Please follow the safety requirements below when installing EcoFoot5D:
•Always keep children and unauthorized people away from work areas.
•Always wear required OSHA approved Personal Protective Equipment (PPE).
•Always use insulated tools when working with or near electrical systems.
•Always provide OSHA approved fall protection for all installation personnel.
•Never wear jewelry during mechanical and electrical installation work.
•Never work in rain, snow or extremely windy conditions.
•Never leave a module unsupported or unsecured on the roof.
•Never install broken photovoltaic modules.
EcoFoot5D General Application Notes
Site-Specific System Design: Ecolibrium Solar provides drafting services on all EcoFoot5D projects. This
service produces a site-specific design package with an Engineered Stamped Layout including detailed ballast
plan and bill of materials.
Roof Type: EcoFoot5D is designed to mount photovoltaic modules to a range of roof surfaces, including:
EPDM, TPO, PVC, Mineral Cap Sheet (a.k.a. Rolled Asphalt), Tar and Gravel.
Roof Slope Range: 0-7 degrees maximum, 3-degree limit for unattached seismic.
Wind Zone: EcoFoot5D is designed to mount photovoltaic modules on flat roof surfaces with a maximum pitch
of 7 degrees in areas with extreme wind conditions. Please contact Ecolibrium Solar for clarification or
assistance.
Installation Requirements: EcoFoot5D is a ballasted photovoltaic racking designed as a system. The system
requires all EcoFoot5D components, the specific module, and ballast placement prescribed in the PE stamped
design. The absence of any of these elements in any given sub-array could present a compromised condition on
the roof. Arrays shall not be left unattended in such a state during an installation.

EcoFoot5D Install Guide V1.1-FINAL Page 6 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
This install guide officially documents the components used and proper methods for an EcoFoot5D installation.
Bonding elements are incorporated into EcoFoot5D components. As the system is built on the roof,
components and modules are bonded together. Specific steps to ensure a bonded system are described through
the installation guide. It is the installer’s responsibility to ensure that the system is safely and properly installed,
and that the system is bonded back to a final ground point.
When wiring the array, keep bare copper from contacting bare aluminum.
Thermal and Seismic Design Requirements: EcoFoot5D is a flexible and expandable design that
accommodates various array geometries.
Maximum widths for arrays are as follows:
•60-cell modules, 26 modules in a row
•72-cell modules, 22 modules in a row
Minimum spacing between sub-arrays is 6”. Site specifics may further limit array sizes and spacing.
Seismic and Uplift Design Requirements: EcoFoot5D can be attached when required by seismic and uplift
conditions as specified by the Authority Having Jurisdiction (AHJ). Addendums in this install guide document
the components used and proper methods for an EcoFoot5D installation with attachments. Use the method
required for the specific Fire Code Rating of the PV module.
Re-Inspection: Ecolibrium Solar recommends periodic re-inspection of the installation for loose components,
loose fasteners, and any corrosion, such that if found, the affected components are to be immediately replaced.
Compatible Modules: Ecolibrium Solar has evaluated many photovoltaic modules for installation compatibility
with the EcoFoot5D ballasted racking system. A list of compatible modules may be found in “EcoFoot5D Install
Guide Appendix - Compatible Modules.pdf” on our website: www.ecolibriumsolar.com
UL2703 Qualification: In cases where UL 2703 certification is required, the EcoFoot5D system conforms to the
UL2703 Standard for grounding and bonding and fire ratings. The EcoFoot5D system may be used to ground
and/or mount a PV module complying with UL1703 only when the specific module has been evaluated for
grounding and /or mounting in compliance with the included instructions.
EcoFoot5D Racking maintains a Class A fire rating when installed in landscape orientation according to the
installation instructions, on a low slope roof Class A roof with Type 1 and Type 2 modules. When installing Type
2 modules a Ballast Tray is required. For roofs with lower fire ratings, the existing rating is maintained when
EcoFoot5D is used.
At this time, the EcoFoot5D system is undergoing further testing pertaining to mechanical loading with specific
modules. Further information about Ecolibrium Solar’s UL2703 conformance may be found in “EcoFoot5D
Install Guide Appendix - UL2703 Qualification.pdf” on our website: www.ecolibriumsolar.com
UL2703 System Label: The label shown below is stamped into to the Wind Deflector (identified as component
5 in the installation guide).
The Date Code ABCYZZ shown above will appear on production parts, letters defined as follows:
• ABC shall be an acronym for identifying the source factory
• Y shall be the Quarter of the year (i.e. 1, 2, 3, 4) of manufacture
• ZZ shall be the last 2 digits of the year of manufacture

EcoFoot5D Install Guide V1.1-FINAL Page 7 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
EcoFoot5D Core Components
1EcoFoot5D Base
2Universal Clamp Lower
3 Universal Clamp Upper
4Clevis Pins
5Wind Deflector
6 Ballast Tray
7Mid-Support Upper
8Mid-Support Lower
95/16” Thread-Forming Screw
Hardware Required
All required hardware is included.
Tools Required
½” Deep Socket
Calibrated Torque Wrench
Torque Settings
14 ft-lbs on all Fasteners

EcoFoot5D Install Guide V1.1-FINAL Page 8 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Install EcoFoot5D in 6 Simple Steps
Step 1 – Install Preassembled Universal Clamps into Bases
1.1 Place Lower and Upper Universal Clamp into EcoFoot5D Base as shown.
Note: The Upper Clamp includes a post and nut to install the Wind
Deflector as shown in Step 6.
1.2 Push Clevis Pins completely into EcoFoot5D Base to secure Rocker.
Step 2 – Position Array
2.1 Snap two chalk lines on roof denoting outside edges of the
EcoFoot5D Bases, per project drawing. Start from the
north or south edge. Ensure chalk lines are square.
2.2 Place EcoFoot5D Bases in approximate position throughout
the array.
Installation Tips

Only install Clamps
where modules will
rest.

See Step 3 for
correct placement
and orientation of
Clamps.
Base
Lower Clamp
Upper Clamp
Clevis Pin
Clevis Pin
Bases
Chalk Lines
Installation Tips

As you build the
array, panels will
space the Bases.
Roughly place a few
rows of Bases at a
time so that they are
within reach of final
location.

EcoFoot5D Install Guide V1.1-FINAL Page 9 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Step 3 – Secure PV Modules onto Bases
3.1 Place PV module onto EcoFoot5D Base.
3.2 Space modules ½” apart using alignment marks located on the Clamps
3.3 Torque Nuts to 14 ft-lbs using a 1/2" deep socket.
Nuts (F) to
Warnings
Step 4 – Install Mid-Support.
4.1 Locate module center point +/-1” using PV module cell lines.
4.2 Press the Upper and Lower Mid-Supports onto the module frame.
Note: On the south row, the Upper Mid-Support will not be pressed onto a module frame.
On the north row, the Lower Mid-Support will not be pressed onto a module frame.
4.3Slide Upper and Lower Mid-Support together using the male/female features.
If required, place optional, self-adhering EPDM pads on the bottom surface of the Upper and Lower
Mid-Supports.
Nut
Base
Module
Nut
PV Module
Center Point
Upper &
Lower
Mid-Support
Press Upper
Mid-Support
on to Frame
Press Lower
Mid-Support on to
Frame
Slide together
Upper & Lower
Mid-Support
Installation Tips

After Step 3, wiring can
be routed and secured.

Standard wire clips or
cable ties (not included)
can be inserted into slots
along Base edge.

EcoFoot5D Install Guide V1.1-FINAL Page 10 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Step 5 – Install Ballast Tray and place ballast blocks on Tray.
5.1 Slide tray into retention clips located on the Base by sliding the Tray along the east-west direction.
5.2 Secure tray to Mid-Support using 5/16” thread forming screw provided with Mid-Support Kit.
Torque Screw to 14 ft-lbs.
5.3 Place ballast (not included) in a single layer evenly dispersed along the length of Ballast Trays. Apply
ballast per the ballast plan specified in the PE Certified Ballast Plan – Sheet S-1.0.
Step 6 – Install Wind Deflector.
6.1 Place Wind Deflectors into slot on EcoFoot5D Base and attach to Rocker using Nut provided.
6.2 Torque Nut to 14 ft-lbs using a ½” deep socket.
Application of anti-seize on threaded post recommended.
Ballast Tray
Base
Retention
Clips
Ballast Tray
5/16” Screw
Rocker
Nut
Base
Retention
Clip
Wind Deflector

EcoFoot5D Install Guide V1.1-FINAL Page 11 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Appendix A: Grounding & Bonding
The EcoFoot5D system has been tested by TüV Rheinland and conforms to UL 2703 for Grounding and
Bonding when installed per the published installation instructions.
EcoFoot5D carries module-to-module ground bond through the Wind Deflector and Mid-Support – Items 5 and
Items 7 & 8 respectively, listed in the “EcoFoot5D Core Components” table in this document.
Each row of modules/wind deflectors in an array of up to 400 modules must be grounded per the NEC and
ANSI/NFPA 70 either through the designated ground hole in the Wind Deflector, or by drilling a ¼” ground hole
into the Wind Deflector a minimum of ½” from any edge. One Ground Lug is required for every 400 modules
connected within an array.
Ecolibrium Solar recommends using #6 copper ground wire in conjunction with WEEB grounding devices such
as the WEEB-LUG-6.7 or WEEB DSK516. Lugs are a single use component.
Other grounding methods must be reviewed and approved by a licensed master electrician or electrical
engineer and Authority Having Jurisdiction (AHJ).
Green lines represent ground bond path.
Wind Deflectors carry module-to-module
east/west ground bond. Mid-Supports carry
row-to-row north/south ground bond.
Grounding and Bonding Path
Ground Lug
Ground Hole with Lug Installed
Ground Lug is installed in the Wind Deflector
either in the designated ground hole or by
drilling a ¼” ground hole into the Wind
Deflector a minimum of ½” from any edge.
One Ground Lug is required for every 400
modules within an array.
Ground Lug
▲
N

EcoFoot5D Install Guide V1.1-FINAL Page 12 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Appendix B: Roof Attachment Methods
EcoFoot5D can be attached when required by seismic and uplift conditions or the Authority Having Jurisdiction
(AHJ). There are 3 methods of attachment that satisfy seismic and uplift requirements for Type 1 and Type 2
modules. Use the method indicated for the specific Fire Code Rating of the PV module. The Ballast Tray is not
required for attachment method for Modules with a Type 1 Fire Code Rating. The Ballast Tray is required for
attachment method for Modules with a Type 2 Fire Code Rating.
Attachment Methods
Seismic and Uplift Attachment Seismic Attachment
Modules with Type 1 Fire Code Rating
Use Attachment with Strut
Modules with Type 1 & 2 Fire Code Rating
Use Attachment with Ballast Tray
Modules with Type 1 & 2 Fire Code Rating
Use Attachment with Ballast Tray and Strut
Attachment with Strut
Attachment with Strut – Components included in Kit
1L-Bracket, 2”x3” –
Qty 3
2Elevator Bolt, 1/4"-20 x 1-1/2”
Qty 2
2Nut, Serrated Flange 1/4"-20
Qty 2
4Nut, Strut 3/8"-16 x 1”
Qty 3
3Nut, Serrated Flange 3/8"-16
Qty 1
6 Bolt, Serrated Flange 3/8"-16
Qty 3
Components Not Included in Kit
Strut, 1-5/8” x 1-5/8”
Roof Attachment (Flat Plate or
Station Anchor)
Tools Required
7/16” Deep Socket
9/16” Deep Socket
9/16” Open-End Wrench
Calibrated Torque Wrench
Torque Settings
8 ft-lbs for 1/4" fasteners, 14 ft-lbs. for 3/8” fasteners

EcoFoot5D Install Guide V1.1-FINAL Page 13 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Attachment with Strut Instruction
Step 1 – Attach L-Bracket to Bases and Roof Attachment
1.1 Bases - insert Elevator Bolt through square hole of Base. Place L-Bracket on Elevator Bolt and secure
with ¼”-20 Serrated Flange Nut.
1.2Roof Attachment - Place L-Bracket on Stud and secure with 3/8”-16 Serrated Flange Nut.
Step 2 – Install Flat Plate or Station Anchor Roof Attachment
2.1 Align L-Bracket of Roof Attachment with L-Brackets on Bases and install Roof Attachment on either
side of the Mid-Support. Install Roof Attachment per Roof Attachment manufacturer’s instructions.
Elevator Bolt
L-Bracket &
Flange Nut
Line between
L-Brackets
Roof Attachment
(Flat Plate or Station Anchor)
Mid-Support
L-Bracket &
Flange Nut
Stud

EcoFoot5D Install Guide V1.1-FINAL Page 14 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Step 3 – Attach Strut to L-Brackets and Tighten Hardware
3.1 Secure Strut to L-Brackets with 3/8”-16 Serrated Hex Bolt and 3/8”-16 Strut Nut. Engage
grooves of Strut Nut with the two lips within Strut.
3.2 Tighten and torque all hardware. Torque ¼”—20 hardware to 8 ft-lbs. Torque 3/8”—16 hardware to 14
ft-lbs.

EcoFoot5D Install Guide V1.1-FINAL Page 15 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Attachment with Ballast Tray
Attachment with Ballast Tray – Components included in Kit
1Elevator Bolt, 1/4"-20 x 3/4”
Qty 4
2Nut, Coupling 1/4"-20 x 7/8”
Qty 4
3Washer, 7/16" ID x 1 OD
Qty 6
4Bolt, Serrated Flange 1/4”-20
Qty 4
5Nut, Serrated Flange 3/8"-16
Qty 2
Not Included in Kit
Roof Attachment (Flat Plate)
Optional Addition of Strut to Ballast Tray – Components Included in Kit
1Screw, Sheet Metal #12 x ¾”
Qty 6
2Washer, Fender ¼” ID x 1” OD
Qty 6
Not Included in Kit
Strut, 1-5/8” x 1-5/8”
Torque Settings
8 ft-lbs for 1/4" fasteners, 14 ft-lbs. for 3/8”
fasteners, 5 ft-lbs for sheet metal screws
Tools Required
7/16” Deep Socket
5/16” Hex Driver
9/16” Socket
Calibrated Torque Wrench

EcoFoot5D Install Guide V1.1-FINAL Page 16 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Attachment with Ballast Tray Instruction
Step 1 – Install Attachment
1.1 Use Ballast Tray to Position Roof Attachment. Stud of Roof Attachment will extend through one of the
slots in middle of Ballast Tray.
1.2 Mark Attachment location, remove Ballast Tray, install Roof Attachment per manufacturer’s
instructions.
Note: Position the attachment such that it can share the same slot with the Mid-Support as shown.
Step 2 – Install Mid-Span Support
2.1 Refer to Step 4 of the Installation Guide to install Mid-Span Support.
Step 3 – Install Hardware on Attachment Stud
3.1 Install 3/8”-16 Serrated Flange Nut and 7/16 ID x 1” OD Washer onto Roof Attachment stud.
Level top of Washer with top of Mid-Span Support.
Level Washer with top of
Mid-Span Support Bracket
Roof
Attachment
Washer and
Flange Nut
Stud

EcoFoot5D Install Guide V1.1-FINAL Page 17 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Step 4 – Install Hardware on Bases
4.1 Install Elevator Bolts and Nut Coupling into EcoFoot 5D bases. Torque to 8 ft-lb.
Repeat process on both Bases.
Step 5 – Install Ballast Tray and secure to Mid-Span Support & Bases
5.1 Referring to Step 5 of the Installation Guide, install Ballast Tray. Line up slots with attachment stud,
base hardware and Mid-Support.
5.2 Torque fastener into Mid-Span Support to 14 ft-lbs. through slot on Ballast-Tray.
5.3 Fasten Ballast Tray to base with Washers and Serrated Hex Bolts on both bases.
Torque to 8 ft-lb.
5.4 Install Washer and Serrated-Flange Nut onto Preferred Roof Attachment in order shown below.
Torque Serrated -Flange Nut to 14 ft-lbs.
5.5 Roof Attachment installation complete for Seismic Rated Attachment System.
Nut Coupling
and Elevator Bolts
Washers and
Serrated Hex
Bolts
Washer and
Serrated Hex Nut
Serrated
Hex Bolt

EcoFoot5D Install Guide V1.1-FINAL Page 18 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Step 6 - Optional Addition of Strut to the Attachment with Ballast Tray
Adding strut to the Attachment with Ballast Tray provides additional rating for uplift strength to offset or
eliminate ballast in a localized region around the attachment point.
6.1 Lay Strut along length of Ballast Trays, centering Strut over Roof Attachment.
6.2 Install two Sheet-Metal Screws and Fender Washers on either side and as close to the roof attachment
stud as possible. Install additional screws along the length of the strut at no more than 24” intervals.
Strut reinforcement attachment complete.
Sheet-Metal Screws with Fender
Washers installed along the length of
the strut at no more than 24” intervals.
One Screw on either side of Roof
Attachment.
Lay Strut on
Ballast Trays
Install Two Sheet-Metal
Screws with Fender
Washers close to Roof
Attachment.

EcoFoot5D Install Guide V1.1-FINAL Page 19 of 19
January 25, 2018, ES10560 ecolibriumsolar.com
Strut Installation Note
Strut may need to be cut and/or spliced to meet the attachment requirements in the project’s Ballast Layout
Plan or engineering report. Splice Strut and install hardware as shown. All hardware is included in the Strut Kit.
Splice Kit