Winegard MT-SM40 User manual

Assembly & Installation Manual MT-SM40
Window/Side Vehicle Mount
www.winegard.com/trucking
For help, email [e-mail]
or call 1-800-788-4417
Manual disponible
en español en www.
winegard/support
2452428
Rev1 5-19

Parts
Recommended tools, not provided:
T20 Torx/Star screwdriver, Phillips screwdriver 5/16" drive,
Adjustable wrench
Back
Support
Clip
Rubber Bumper (2)
10-32 x 1/4” Screw (3)
10-32 x 1/2” Screw (1)
Exterior
Bracket (2)
Rubber Washer (1)
Mounting Screw (10)
Rubber Foot (4)*
*Included with
antenna unit
3" x 3" Film Plastic (2)
(not shown)
Base
Plate
10-32” Nylock Nut (2)
1/4-20 x .75 Hex Screw (2)
Metal Washer (2)
Specifications
•For use with Winegard PL-7000, PL7000R, PL-8000,
PL8000R, PL-8035, PL8035R, GM-9000, GM-9035,
PA-1000, PA1000R, PA-2000, PA-2035, PA2000R,
PA2035R, GM-6000, GM-6035.
•For stationary use only
•Height (once assembled): 13.35", Width: 10.25"
•Extends 5.75" from vehicle
•Adjustable vertical mounting settings every 1.5"
•Window clip swivels 90° to easily level antenna
•Mount weight: 2 lbs
Only hang the window mount assembly on
the window when the vehicle is parked and
the antenna is in use; store the window
mount assembly when not in use.
Model MT-SM40 window mount should
only be deployed when the vehicle is
stationary. Do not use while the vehicle is
moving. Remove prior to traveling.

Failure to install in accordance with product
manufacturer’s installation and assembly
instructions could result in property damage,
personal injury, and/or death.
Step 1
Step 2
Step 3
Step 4
Electronics
Board
Hex Screws
Metal Washers
and Nylock Nuts
Assembling the Window Mount
To use with antenna models: PL-7000, PL7000R,
PL-8000, PL8000R, PL-8035, PL8035R, GM-9000,
GM-9035.
1. Align the hole in the clip with the press nut at
the top of the back support. The hole in the clip
should fit around the raised lip of the press nut.
Insert a 10-32 x 1/4"screw through the aligned
holes in the clip and back support, and tighten.
2. Push the two rubber bumpers through the two
holes in the bottom of the back support. Make
sure the rubber bumpers are fully installed
before proceeding, as these will prevent the
mount from scratching the vehicle.
3. Remove the antenna dome screws with T20 Torx/
Star screwdriver or bit. DO NOT USE A DRILL.
Use caution on edge of reflector and gearing. The
reflector can be sharp. See WARNING below:
To discharge any built up static electricity after
removing the dome, touch the coax connection on
the base of the antenna.
DO NOT TOUCH the electronics board or any
components. See Step 3 image.
4. Align the holes on the base plate of the mount
with the holes in antenna base and screw them
together with the two hex screws up from the
bottom and fastened inside the dome base with
the two metal washers and Nylock nuts. See
Step 4 images.
5. Carefully replace the dome on the antenna, and
secure with the dome screws. Align the back
of the base plate with the back support and
connect the two together with the remaining
two 10-32 x 1/4”screws. See completed image
on opposite page.
After removing the dome, do not touch the
electronics board. Static discharge could
damage electronics and cause antenna to
become inoperable.

Failure to install in accordance with product
manufacturer’s installation and assembly
instructions could result in property damage,
personal injury, and/or death.
Step 7
Rubber Feet,
Foot Screws
Rubber Feet,
Foot Screws
Assembling the Window Mount
To use with antenna models: PA-1000, PA1000R,
PA-2000, PA-2035, PA2000R, PA2035R, GM-
6000, GM-6035.
1. Align the hole in the clip with the press nut at
the top of the back support. The hole in the clip
should fit around the raised lip of the press nut.
Insert a 10-32 x 1/4"screw through the aligned
holes in the clip and back support, and tighten.
2. Push the two rubber bumpers through the two
holes in the bottom of the back support. Make
sure the rubber bumpers are fully installed before
proceeding, as these will prevent the mount from
scratching the vehicle.
3. Determine the preferred height of the window
mount base against the back support. Align the
bottom hole in the window mount base with the
preferred hole in the back support. Insert a
10-32 x 1/2"screw through the aligned holes
in the back support and base plate. Tighten.
4. Remove the two rubber feet and two foot screws
that will sit on the mount base from the bottom
of the antenna. Set aside until step 7.
5. Remove the dome screw facing the back support
with a 5/16”drive.
6. Align the hole in the dome with the hole in the
window mount base and back support. Install the
dome screw, with the rubber washer between the
dome and back support. Tighten.
7. To complete the installation, position the flat side
of the two rubber feet against the holes on the
bottom of the window mount base, and install
the two screws through the aligned holes in the
rubber feet, window mount base, and antenna
base. Tighten to 40 in* lbs.
Step 3
Step 1
Step 2
Step 4
Rubber
Washer
Back
Support
Dome
Screw
Dome
Step 7
Steps 5-6

A 25 foot coaxial cable is included and recommended for use with the antenna.
If using an alternate cable, all cabling should be RG6 with a maximum length
of 50 feet from Playmaker to receiver.
Connect Coax to Antenna
Connect the provided coax cable from the antenna coax port to the “Sat In”
port on the back of the receiver. Tighten coax connection until finger-tight,
and then tighten a quarter turn more with a wrench. Do not overtighten.
Selecting Antenna Location
Choose a location with a clear, unobstructed view of the southern sky. Avoid
obstructions such as trees, hills, vehicles, or buildings — these can block the
signal from the satellite.
Do not place the antenna in a path of people or vehicles’ otherwise, the
antenna may be knocked off of the signal if run into, or cables may be
disconnected from the unit.
The antenna may take longer to lock onto signal if the antenna is not level.
Use Winegard’s Signal Finder App
with augmented reality to determine optimal location.
AR view (Augmented Reality)
Point your phone at the southern sky.
See signal obstructions such as trees
and buildings.
FREE AT
Finding your favorite TV programming
has never been easier! Using your current
location, the app can help determine the
correct antenna positioning to avoid
obstructions with the augmented
reality (AR) view.

Only hang the window mount assembly on an exterior bracket when the
vehicle is parked and the antenna is in use; store the window mount
assembly when not in use. Model MT-SM40 window mount should only
be deployed when the vehicle is stationary. Do not use while the vehicle
is moving. Remove prior to traveling.
Top
Bottom
Hanging on Window or Exterior Brackets
Once ready to use the antenna, hang the window mount assembly
on the window or exterior bracket.
If hanging the assembly on the vehicle window, apply the plastic
film where the mount will be hung on the window, and then slide
the clip over the plastic film. The window may need to remain
slightly open when the window mount is on the window.
If hanging the assembly on the exterior bracket, make sure the
sealant is dry, and slide the clip into the exterior bracket. When
placing the antenna on the optional exterior bracket, ensure that
the window mount is properly secured to the optional exterior
bracket; failure to secure properly may result in injury.
Installation of Exterior Brackets
After the antenna has been secured to the mount, the
assembly can be hung on the edge of a window or on the
provided exterior brackets. The exterior brackets will enable
the assembly to be hung on the exterior of the vehicle.
Complete the following steps to install the exterior brackets
on the vehicle.
1. Choose a location on the exterior of the vehicle for the
exterior brackets. Consider possible obstructions to the
satellite line-of-sight and where cables will be run.
2. Clean the areas where the exterior brackets will be installed on the vehicle.
3. Position an exterior bracket over one of the chosen locations for installation,
making sure that the top of the exterior bracket is oriented upwards (see
image to right for reference). Keep in mind that the antenna assembly
should be level front-to-back and side-to-side for best operation.
4. Trace around the edge of the bracket, and mark pilot holes through the
bracket.
5. Drill the pilot holes.
6. Apply sealant in the traced area.
7. Mount the exterior bracket with four of the provided mounting screws.
8. Apply sealant over the screws.
9. If using the second exterior bracket repeat steps 3–8.

Do not walk under the window mount assembly when deployed.
The window mount should be carefully hung when attaching to the window,
or the window may be damaged.
Care should be taken when using the window mount in inclement weather.
When placing the antenna on the optional exterior bracket, ensure
that the window mount is properly secured to the optional exterior
bracket; failure to secure properly may result in injury.
Model MT-SM40 window mount is intended for stationary use only and
must be removed prior to traveling. Do not deploy the window mount
while the vehicle is in motion.
Before Traveling
1. Turn off all power.
2. Disconnect all cables (power and/or coax) from the Winegard product.
3. Carefully remove the antenna/extender and window mount from the window
or exterior bracket.
4. Store inside the vehicle while traveling.
Warnings

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
(2 YEARS PARTS; 1 YEAR LABOR)
Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years
from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized
labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored
unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate
the nearest authorized Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601,
Telephone [phone] or visit www.winegard.com). Customer must provide proof of purchase with a dated sales
receipt for the Winegard product to verify the product is under warranty. If the date of purchase cannot be verified, the
warranty period shall be considered to begin thirty (30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer
for service. Customer must provide proof of purchase to verify the product is under warranty. If the product is brought
to an authorized Winegard dealer for service prior to expiration of year one (1) of the warranty period and a defect in
material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard
dealer’s labor charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance
for pre-approval of the service. Approval of the service is at the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 2736 Mt. Pleasant
Street, Burlington, Iowa 52601, Telephone [phone]). Customer must return the product along with a brief
description of the problem and provide Winegard Technical Services with Customer’s name, address, and phone
number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned
before the expiration of the warranty period, Winegard Company will (at its option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails
from: improper installation, misuse, abuse, neglect, accident, tampering, modification of the product as originally
manufactured by Winegard in any manner whatsoever, removing or defacing any serial number, usage not in
accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive
environments such as salt spray and acid rain. This Limited Warranty also does not apply if the product becomes
unable to perform its' intended function in any way as a result of the television signal provider making any changes in
technology or service.
RETURN AUTHORIZATION POLICY
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard
Warranty Services under this warranty policy. Please call our Technical Services Department at 800-788-4417 or send
an email to [email protected] to obtain the RMA number. Please furnish the date of purchase when requesting
an RMA number. Enclose the product in a prepaid package and write the RMA number in large, clear letters on the
outside of the package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an
unauthorized return(s) will be refused and returned to Customer freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,
MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR
A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential
damages, the above limitations or exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state
to state.
WS-MOBWARREV3 Rev. 10/14
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601
1-800-288-8094 • Fax [phone] • www.winegard.com
Printed in U.S.A. ©2019 Winegard Company Rev1 5-19 2452428
Disclaimer: Although every effort has been made to ensure that the information in
this manual is correct and complete, no company shall be held liable for any errors or
omissions in this manual. Information provided in this manual was accurate at time
of distribution. If the antenna and/or mount do(es) not function as expected, please
contact Winegard by emailing [e-mail] or calling 1-800-788-4417.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and
other countries. App Store is a service mark of Apple Inc., registered in the U.S. and
other countries. Google Play and the Google Play logo are trademarks of Google LLC.
Winegard® is a registered trademark of Winegard Company.
www.winegard.com
For help, email [e-mail] or call 1-800-788-4417