Insignia NS-HTVMF0C User manual

Before using your new product, please read these instructions to prevent any damage.
Fixed-Position Wall Mount
for TVs 40–70 in.
NS-HTVMF0C
INSTALLATION GUIDE

2www.insigniaproducts.com
Safety information and specifications
CAUTION: IMPORTANT SAFETY
INSTRUCTIONS - SAVE THESE
INSTRUCTIONS - READ THE
ENTIRE MANUAL PRIOR TO USE
CAUTION: Do not use this product for any
purpose not explicitly specified by Insignia.
Improper installation may cause property
damage or personal injury. If you do not
understand these directions, or have doubts
about the safety of the installation, contact
Customer Service or call a qualified contractor.
Insignia is not responsible for damage or injury
caused by incorrect installation or use.
CAUTION: Do not exceed the maximum weight indicated.This mounting system is intended for use only
with the maximum weights indicated. Use with products heavier than the maximum weights indicated
may result in collapse of the mount and its accessories, causing possible injury.
The weight of yourTV must not exceed 100 lbs. (45.3 kg).The wall must be capable of supporting five times
the weight of yourTV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young
children!
Maximum TV weight: 100 lbs. (45.3 kg)
Screen size: 40 in. to 70 in. diagonal
Overall dimensions (H × W ):
17.0 × 25.6 in. (43.2 × 65 cm)
Wall-mount weight: 2.4 lb (1.1 kg)
We’re here for you
www.insigniaproducts.com
For customer service, call:
877-467-4289 (U.S./Canada markets)
17.0 in. (43.2 cm)
2.97 in. (7.5 cm)
25.6 in. (65 cm)

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
3
www.insigniaproducts.com
Tools needed
You will need the following tools to assemble your newTV wall mount:
ardware
Package contents
Make sure that you have all the hardware necessary to assemble your new TV wall mount:
10 Wall Plate (1) 1 TV Brackets (2) RWall Plate Template (1)
Edge-to-edge
stud finder
Level
Phillips screwdriver
Socket wrench with 1/2 in.
(13 mm) socket or adjustable
wrench
Measuring tape
Drill
7/32 in. (5.5 mm) wood drill
bit (for wood stud wall)
OR
3/8 in. (10 mm) masonry
drill bit (for solid concrete
or concrete block walls)
Hammer
Tape
Pencil Awl
Wallmount template

10 (1) 1 (2) R

4www.insigniaproducts.com
TV Hardware Bag
Note: Deleted ruler.
Label Hardware Qty.
22
34
44
54
64
TV Standoff
M6 × 12 mm
screw
M8 × 16 mm
screw
M8 × 20 mm
screw
M6 × 35 mm
screw
Label Hardware Qty.
74
84
94
11 2
12 2
M8 × 35 mm screw
M6/M8 washer
Spacers
5/16 in. × 2 3/4 in. lag bolt
Lag bolt washer
Concrete Installation Kit CMK1 (not included)
Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you.
C1 2
C2 2
C3 2
5/16 in. × 2 3/4 in. lag bolt
Lag bolt washer
Concrete anchors

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
5
www.insigniaproducts.com
Installation instructions
STEP 1 - Determining whether your TV has a flat back or an
irregular or obstructed back
1Carefully place yourTV screen face-down on a cushioned, clean surface to protect the screen from
damages and scratches.
2If yourTV has a table-top stand attached, remove the stand. See the documentation that came with your
TV for instructions.
3Temporarily lay the TV brackets (1), oriented vertically, on the back of yourTV.
4Align the screw holes in theTV brackets with the mounting screw holes on your TV.
5Identify which type of back yourTV may have:
•Flat back: The brackets lay flush against the back of your TV and do not block any jacks.You do not need
spacers when assembling the wall mount.
•Obstructed back:The brackets block one or more of the jacks on the back of your TV. You will need
spacers when assembling the wall mount.
•Irregularly-shaped back:There is a gap between a bracket and some part of the back of your TV. You
will need spacers when assembling the wall mount.
6Remove the TV brackets (1).

6www.insigniaproducts.com
STEP 2 - Select screws, washers, and spacers
1Select the hardware for yourTV (screws, washers, and spacers). A limited number ofTVs come with
mounting hardware included. (If there are screws that came with the TV, they are almost always in the
holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV
requires, test various sizes by hand threading the screws.
Select one of the following types of screws:
For a TV with a flat back:
M6 X 12mm screws (3)
M8 X 16mm screws (4)
M8 X 20mm screws (5)
For a TV with an irregular/obstructed back:
M6 X 35mm screws (6)
M8 X 35mm screws (7)
Select an M6/M8 washer (8) for each screw.
For an irregular or obstructed TV back, also use the spacers (9)
CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate
threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer
service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long
may damage your TV. However, using a screw that is too short may cause your TV to fall from the mount.
2Remove the screws from the holes in the back of your TV.
3For a flat backTV, go to “STEP 3 - Option 1: Attaching the mounting hardware toTVs with a flat back“ on
page 7.
-OR-
For an irregular or obstructed back, go to “STEP 3 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs”on page 8.
Screw is too
long
Screw fits
correctly
Screw is too
short

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
7
www.insigniaproducts.com
STEP 3 - Option 1: Attaching the mounting hardware to TVs
with a flat back
1Align the left and rightTV brackets (1) with the upper screw holes on the back of the TV. Make sure that
the brackets are level.
2Install washers (8) and screws (3, 4, or 5) into the holes in the back of the TV.
3InstallTV standoffs (2) in the lower screw holes on the back of theTV using washers (8) and screws (3, 4,
or 5).
4Tighten the screws until they are snug against theTV brackets. Do not over tighten.
You’ l l need
Important: After attaching
the TV brackets, adjust the
straps (by sliding the buckle
up or down) so they are level
with the bottom of the TV.
2(2)
3 (4)
Phillips screwdriver
1 TV
brackets (2)
or
4 (4)
8(4)
5 (4)
Level
or

8www.insigniaproducts.com
STEP 3 - Option 2: Attaching the mounting hardware to TVs
with irregular or obstructed backs
1Place spacers (9) over the screw holes on the back of theTV.
2Align the left and rightTV brackets (1) with the upper screw holes on the back of the TV. Make sure that
the brackets are level.
3Place washers (8) over the holes in the TV brackets. Insert screws (6 or 7) through the washers,TV
brackets, and spacers.
4Install TV standoffs (2) in the lower screw holes on the back of the TV using washers (8), screws (6or 7),
and spacers (9).
5Tighten the screws until they are snug against theTV brackets. Do not over tighten.
You’ l l need
Important: After attaching the
TV brackets, adjust the straps (by
sliding the buckle up or down)
so they are level with the bottom
of the TV.
6 (4)
9(4)
1 TV
brackets (2)
8(4)
7 (4)
or
2(2) Phillips screwdriver
Level

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
9
www.insigniaproducts.com
STEP 4 - Determine wall-mount location
Note:
• For more detailed information on determining where to drill your holes, visit our online height-finder
at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder
• Your TV should be high enough so your eyes are level with the middle of the screen. This is normally
40 to 60 in. from the ground.
1Measure the distance from the bottom of yourTV to the top of the one of theTV brackets you just
installed in step 3. This is measurement a.
2Measure the distance from the floor to where you want the bottom of theTV to be placed on the wall.
Keep in mind that the bottom of theTV should be placed above any furniture (such as entertainment
centers orTV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray
player or cable box).This measurement is b.
3Add a + b then subtract 1.5 in. The total measurement is the height where you want the center of the
wall plate to be on the wall.
4Use a pencil to mark this spot on the wall.
You’ll need
A
B
a
b
Measuring tape
Pencil

10 www.insigniaproducts.com
STEP 5 - Option 1: Installing on a wood stud* wall
Note: Any drywall covering the wall must not exceed 5/8 in. (16 mm).
1Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.
2Align the center of the wall plate template (R) at the height (a + b - 1.5 in.) you determined in the
previous step, make sure that it is level, then tape it to the wall.
3Drill two pilot holes through the template to a depth of 3 in. (75 mm) using a 7/32 in. (5.5 mm) diameter
drill bit, then remove the template.
4Align the wall plate (10) with the pilot holes, insert the lag bolts (11) through the lag bolt washers (12),
then through the holes in the wall plate.Tighten the lag bolts only until they are firm against the wall
plate.
CAUTION:
• Use only the upper slotted holes to mount the wall plate. Do not use the lower slotted holes.
• Install in the center of the studs. Do Not install in drywall alone.

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
11
www.insigniaproducts.com
• DO NOT over-tighten the lag bolts (11).
You’ll need
3 in.
75 mm)
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 11/2 x 31/2 in. (38 x 89 mm).
* Minimum horizontal spacing between fasteners cannot be less than 16 in. (406 mm).
Align the center of the
template with the height mark
(a+b) you made in step 4.
Edge-to edge
stud finder
11 (2)
Drill
7/32 in. wood drill bit 1/2 in. socket
wrench
Wall plate (10)
12 (2)
Wall plate template (R)
Tape
Wallmount template

Level

12 www.insigniaproducts.com
STEP 5 - Option 2: Installing on a solid concrete or concrete
block wall (requires Concrete Installation Kit CMK1)
CAUTION:To prevent property damage or personal injury, never drill into the mortar between the
blocks. Mount the wall plate directly onto the concrete surface.
1Align the center of the wall plate template (R) at the height (a + b - 1.5 in.) you determined in the
previous step, make sure that it is level, then tape it to the wall.
2Drill two pilot holes through the template to a depth of 3 in. (75 mm) using a 3/8 in. (10 mm) diameter
masonry drill bit, then remove the template.
3Insert the concrete wall anchors (C3) into the pilot holes and use a hammer to make sure the anchors are
flush with the concrete surface.
4Align the wall plate (10) with the anchors, insert the lag bolts (C1) through the lag bolt washers (C2),
then through the holes in the wall plate.Tighten the lag bolts only until they are firm against the wall
plate.
CAUTION:
• Use only the upper slotted holes to mount the wall plate. Do not use the lower slotted holes.

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
13
www.insigniaproducts.com
• DO NOT over-tighten the lag bolts (C1).
.
You’ll need
C3
C1 C2
3 in.
(75 mm)
* Minimum solid concrete thickness: 8 in.
(203mm)
* Minimum concrete block size: 8 x 8 x 16
in. (203 x 203 x 406 mm).
* Minimum horizontal spacing between
fasteners cannot be less than 16 in. (406
mm).
Align the center of the template with the
height mark (a+b) you made in step 4.
C1 (2)
Drill
1/2 in. socket
wrench
Level
C2 (2)
Wall plate template (R)
Tape
Hammer
Wall plate (10)
Wallmount template

3/8 in. masonry
drill bit

14 www.insigniaproducts.com
STEP 6 - Mounting the TV to the wall plate
1Holding theTV with the top of the screen tilted toward the wall, slide the upper notches of the right and
left TV brackets (1) over the upper lip of the wall plate (10).
2Push the bottom of the TV toward the wall until the latch mechanism clicks into place.
HEAVY! You will need
assistance with this step.

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
15
www.insigniaproducts.com
Removing the TV from the wall plate
• Pull down and hold both release straps, then pull the bottom of the TV away from the wall and lift the
assembly off the wall plate.
HEAVY! You will need
assistance with this step.

16 www.insigniaproducts.com
ONE-YEAR LIMITED WARRANTY
Definitions:
The Distributor* of Insignia branded products warrants to you, the original purchaser of this new
Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the
material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty
Period”).
For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy
branded retail store or online at www.bestbuy.com or www.bestbuy.ca and is packaged with this warranty
statement.
How long does the coverage last?
TheWarranty Period lasts for 1 year (365 days) from the date you purchased the Product. Your purchase date is
printed on the receipt you received with the Product.
What does this warranty cover?
During theWarranty Period, if the original manufacture of the material or workmanship of the Product is
determined to be defective by an authorized Insignia repair center or store personnel, Insignia will (at its sole
option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or
rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of
Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires,
you must pay all labor and parts charges. This warranty lasts as long as you own your Insignia Product during the
Warranty Period.Warranty coverage terminates if you sell or otherwise transfer the Product.
How to obtain warranty service?
If you purchased the Product at a Best Buy retail store location or from a Best Buy online website
(www.bestbuy.com or www.bestbuy.ca), please take your original receipt and the Product to any Best Buy store.
Make sure that you place the Product in its original packaging or packaging that provides the same amount of
protection as the original packaging.
To obtain warranty service, in the United States and Canada call 1-877-467-4289. Call agents may diagnose and
correct the issue over the phone.
Where is the warranty valid?
This warranty is valid only in the United States and Canada at Best Buy branded retail stores or websites to the
original purchaser of the product in the country where the original purchase was made.
What does the warranty not cover?
This warranty does not cover:
• Customer instruction/education
•Installation
•Setupadjustments
• Cosmetic damage
• Damage due to weather, lightning, and other acts of God, such as power surges
• Accidental damage
•Misuse
•Abuse
• Negligence
• Commercial purposes/use, including but not limited to use in a place of business or in communal areas of
a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a
private home.
• Modification of any part of the Product, including the antenna
• Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
• Damage due to incorrect operation or maintenance
• Connection to an incorrect voltage or power supply
• Attempted repair by any person not authorized by Insignia to service the Product
• Products sold “as is”or “with all faults”

FIXED-POSITION WALL MOUNT FOR TVs 40-70 in.
17
www.insigniaproducts.com
• Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)
• Products where the factory applied serial number has been altered or removed
• Loss orTheft of this product or any part of the product
• Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated)
grouped in an area smaller than one tenth (1/10) of the display size or up to five (5) pixel failures
throughout the display. (Pixel based displays may contain a limited number of pixels that may not
function normally.)
• Failures or Damage caused by any contact including but not limited to liquids, gels or pastes.
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF
WARRANTY. INSIGNIA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH
OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITEDTO, LOST DATA, LOSS OF
USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES NO OTHER EXPRESS
WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIEDWARRANTIES FORTHE PRODUCT,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE
AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED,WILL APPLY AFTER THEWARRANTY PERIOD. SOME STATES,
PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.THISWARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact Insignia:
1-877-467-4289
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies.
*Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.

V4 ENGLISH
20-0110
www.insigniaproducts.com
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
Part Number: 6907-302037