ecopoint EBT1550W24W840-G2 Instruction sheet

WARRANTY COVER: CONTACT:
Ecopoint Limited guarantees this luminaire
to be free from failures resulting from
faulty materials or workmanship for a
period of 5 years from the date of invoice.
Retain the invoice as proof of purchase in
the event of a warranty claim.
Failure resulting from misuse, accident,
neglect or improper operation,
maintenance, installation, modication or
adjustment are not covered by this
warranty.
Ecopoint Limited must be notied within
30 days of the alleged defect being rst
identied.
Please refer to standard Warranty Terms
and Terms and Conditions of Sale for full
detail; these are available at
www.ecopoint.co.nz
For any service or support enquiries,
please call Ecopoint head oce during
normal business hours (Monday to Friday)
or contact us via any of the means listed
below.
Ecopoint Limited
2 Jarden Mile, Ngauranga, Wellington 6035
PO Box 12646, Thorndon, Wellington 6144
P: [phone] or
0800 695 949
E: [e-mail]
W: www.ecopoint.co.nz
MAINTENANCE:
 To avoid risk of harm to the luminaire or maintenance personnel, always en-
sure that the luminaire is switched o and cooled down prior to undertaking
any maintenance activities.
 If maintenance tasks involve exposing any electrical components, ensure
that mains power is disconnected prior to any works.
 This product should only be cleaned with a damp cloth; do NOT use any
chemical cleaning agents and/or solvents.
 If dust accumulates on the inside of the diuser, simply slide the end-caps of
the luminaire body o, slide the diuser out, wipe down with a damp cloth
and allow to dry before reversing the process. CARE MUST BE TAKEN TO NOT
TOUCH ANY LEDS AND NOT ALLOW ANY MOISTURE TO COME IN CONTACT
WITH THE LEDS.
 REMINDER: No components of this luminaire are serviceable by the user,;
damaged components may only replaced or repaired by the manufacturer or
approved agent.
IMPORTANT:
Surface Mount Batten Gen 2
| Product Instructions
55 mm
1550 mm
100 mm
Mass:
2.2 kg (all models)
DIMENSIONS:
FOR YOUR SAFETY AND THE LONG-TERM RELIABILTY OF THIS PRODUCT, READ AND
FOLLOW ALL INSTRUCTIONS TO PREVENT HARM TO THE LUMINAIRE, INSTALLER OR
PROPERTY.
 Installation requires knowledge of electrical and luminaire systems; installa-
tion must only be completed by a licenced or suitably qualied electrician.
 Disconnect power before installation.
 Do not alter pre-existing holes or drill new holes unless instructed to do so
according to this manual.
 Do not expose wiring to sharp objects or edges of sheet metal, always check
clearances prior to any drilling and de-burr edges.
 No components of this luminaire are serviceable by the user, and there is
danger of personal and/or property harm if the luminaire is modied or dis-
assembled.
 If any luminaire components are damaged, they shall be exclusively replaced
by the manufacturer or approved agent.

Power Factor ≥ 0.95 (230V)
Electrical Input 220-240 V / 50-60 Hz
Operating Temperatures - 20 to +40 deg. C
Construction PVC mount, alum. body, PC diuser
Ingress Protection IP20
Impact Protection N/A
Warranty 5 years
STANDARD SPECIFICATIONS
STANDARD MODELS
Product Code Size Power Nominal Flux
EBT1550W24W840-G2 1550 x 100 x 58 mm 26.0 W 3,380 lm
EBT1550W48W840-G2 1550 x 100 x 58 mm 45.1 W 5,800 lm
INSTALLATION NOTES:
The following notes must be considered prior to installation of the product:
 The luminaire has been designed to operate in accordance with the speci-
cations listed above; please especially note the electrical input, operating
temperature and ingress/impact protection specications and ensure that
the luminaire will only be operated within a suitable environment.
 The luminaire must be securely xed to a suitable surface or structure which
is able to bear the luminaire weight and provide the necessary restraint un-
der seismic loading according to NZS 4219.
 The luminaire must be installed such that adequate space is available for
ventilation to prevent overheating.
 Exposure to UV (i.e. direct sunlight) over an extended period may cause dis-
colouration of the diuser and/or luminaire body.
 The luminaire is not suitable for marine environments nor for hazardous or
corrosive environments.

Remove luminaire from packaging, detach body from the light engine
(leaving restraint cables hanging), draw power feed cable through rear
of body, and x the body to the mounting surface.

Attach light engine to the restraint cables, then connect power feed
cable to the fused terminal block on the rear of the light engine.

Conrm electrical connections into the terminal block are secure, then
raise the light engine back up to the level of the body and push-t until
a positive ‘click’ sounds indicates that it has attached correctly.

Connect power to mains supply and test the luminaire for correct oper-
ation and switching.