Edbak ERM100-L User manual

www.edbakproav.com
ERM100-L
ELECTRIC FULL SERVICE VIDEO WALL MOUNT WITH MICRO ADJUSTMENT
UCHWYT SCIENNY WYSUWANY ELEKTRYCZNIE Z MIKRORERULACJA
ERM100-L-IM-01

www.edbakproav.com ERM100-L-IM-01
2 13.05.2019, ERM100-L-IM-01
INSTALLATION MANUAL
INSTRUKCJA MONTAZU
Warning
Please read this manual before starng the installaon to ensure correct assembly.
The assembly should be carried out in accordance with this manual by at least two fully
qualified people. The EDBAK Company shall not be liable for any injuries or damage to
material or property caused by incorrect assembly. Hence please ensure that:
during the assembly all the instrucons are followed carefully. Failure to do so may result
in damage to the product or property, or even personal injury;
before assembly you must ensure that there are no power cables, or water, sewage or
gas pipes in the area of the ceiling where the mount is to be fixed;
when aaching the projector to the mount, please ensure that the screws are of the
correct length and diameter. In order to ensure the correct fit, use the plasc spacers
supplied. Use of the wrong screws may result in permanent product damage. Extra
cauon should be taken with movable parts in order to avoid crushing or pinching your
hands or fingers. The movable parts are idenfied in this manual.
The terms of the product guarantee are detailed in the guarantee card.
Ostrzeżenie
Przed rozpoczęciem montażu należy uważnie zapoznać się z instrukcją uchwytu oraz
ekranu w celu zapewnienia prawidłowego montażu.
Prace montażowe powinny wykonywać co najmniej dwie osoby posiadające kwalifikacje
w zakresie montażu zgodnie z niniejszą instrukcją. Firma EDBAK nie bierze odpowiedzial-
ności za straty materialne oraz uszkodzenia mienia lub ciała, wynikające z nieprawidłowego
montażu. Dlatego należy zawsze przestrzegać:
w trakcie montażu dokładnie przestrzegać załączonej do produktu instrukcji
montażowej, w przeciwnym razie może to prowadzić do zniszczenia sprzętu,
a nawet uszkodzeń ciała,
koniecznie przed montażem upewnić się, że pod powierzchnią ściany, na której będzie
mocowany uchwyt nie ma kabli elektrycznych, rur wodnokanalizacyjnych lub instalacji
gazowych,
w trakcie montażu ekranu do uchwytu upewnić się, że użyte śruby są dobrze dobrane
co do długości i średnicy. W celu idealnego dobrania długości śrub można skorzystać
z dołączonych podkładek plaskowych. Zastosowanie niewłaściwych śrub grozi trwałym
uszkodzeniem sprzętu,
w miejscach wskazanych w instrukcji, w których są ruchome elementy uchwytu zacho-
wać szczególną ostrożność w celu uniknięcia przyciśnięcia, dłoni i palców.
Warunki gwarancji wg załączonej do produktu karty gwarancyjnej.

ERM100-L-IM-01
www.edbakproav.com
3
AA
10A 120W 230VAC/12VDC 5,5 x 2,1mm
1x
PART LIST
LISTA ELEMENTÓW
BB 1x
CC 1x
low voltage dc cable
DC 5,5/2,1 socket,
DC 5,5/2,1 plug x5; straight; 0,5mm2 DD 1 for 5 mounts
13.05.2019, ERM100-L-IM-01

ERM100-L-IM-01
A03M6x20 4x
A04M8x20 4x
A05fi15 x fi8,4 x 5 4x
A06fi15 x fi8,4 x 10 4x
A01M4x20 4x
A02M5x20 4x
PART LIST
LISTA ELEMENTÓW
www.edbakproav.com
4 13.05.2019, ERM100-L-IM-01
A07M8 4x
A08M5 4x
A093mm 1x
A104mm 1x
A115mm 1x
A126mm 1x

ERM100-L-IM-01
B2x
C1x
D1x
DC 5,5/2,1 plug,
DC 5,5/2,1 socket;
straight; 0,5mm2; 2m
EE 6x
FF 6x
6x80
GG 6xM6
A1x
PART LIST
LISTA ELEMENTÓW
www.edbakproav.com
5 13.05.2019, ERM100-L-IM-01

ERM100-L-IM-01
ASSEMBLY
MONTAZ
www.edbakproav.com
6
1
13.05.2019, ERM100-L-IM-01
2
AA
FF
EE
GG
A
INSTALLATION
TO BRICK
OR CONCRETE WALL

ERM100-L-IM-01
ASSEMBLY
MONTAZ
www.edbakproav.com
7 13.05.2019, ERM100-L-IM-01
3
CHECK
THE POSITION
OF FRAME
EE
GG
INSTALLATION
TO WOOD STUD WALL

ERM100-L-IM-01
ASSEMBLY
MONTAZ
www.edbakproav.com
8 13.05.2019, ERM100-L-IM-01
4
CHECK
THE POSITION
OF FRAME
MULTIPLE DISPLAY ASSEMBLY - WITHOUT SPACERS
DISPLAY WIDTH
A = DISPLAY WIDTH
DISPLAY HEIGHT
B = DISPLAY HEIGHT

ERM100-L-IM-01
ASSEMBLY
MONTAZ
www.edbakproav.com
9 13.05.2019, ERM100-L-IM-01
5
7
6
MULTIPLE DISPLAYS ASSEMBLY- USE OF OPTIONAL SPACERS
dedicated
spacer
B
A01/A02/A03/A04
A07/A08
A05/A06
WARNING!
LOCKING
SCREW BB

ERM100-L-IM-01
8
9
10
ASSEMBLY
MONTAZ
www.edbakproav.com
10 13.05.2019, ERM100-L-IM-01
HORIZONTAL
ADJUSTMENT
VERTICAL
ADJUSTMENT
TITLING
ADJUSTMENT

ERM100-L-IM-01
11
12
ASSEMBLY
MONTAZ
www.edbakproav.com
11 13.05.2019, ERM100-L-IM-01
DISPLAY
MICRO
ADJUSTMENT
CONNECTING AND INSTALATION
CABLE
MANAGEMENT
ARM
PLUG
SOCKET

ERM100-L-IM-01
13
ASSEMBLY
MONTAZ
www.edbakproav.com
12 13.05.2019, ERM100-L-IM-01
CC
DD
C

ERM100-L-IM-01
ASSEMBLY
MONTAZ
www.edbakproav.com
13 13.05.2019, ERM100-L-IM-01
Connection
The applicaon works with ZL-RC02 module, which has a built-in Bluetooth 4 module,
so there is no need to pair the module with a smartphone or tablet.
The task of the applicaon is to facilitate the management and control of mulple modules and their operaon.
Change of name
To change the module name, connect to the selected module. Then press the [CHANGE NAME] buon,
then enter the new device name in the yellow "New device name" field. The name may contain only leers, numbers
and addional characters "minus" and "underscore". Aer entering the name, press the [SET] buon.
The device name will be changed and the device will be disconnected and the device will return to the list.
Then search for the device again.
Pin code
The applicaon remembers individual PIN codes for modules in the database located in the device on which it is running.
This is needed to automacally select the correct PIN depending on the device to which you are connecng.
Each change of the PIN code in the device causes a change of the saved PIN code in the database.
Because the module does not inform the applicaon about whether it has changed the PIN code,
the applicaon assumes that the password change has been successful and the new PIN code is saved in the database.
The PIN must be exactly 8 digits.
The yellow field above the [USE PIN] buon should contain the current PIN for the connected module.
If there is no PIN in this field, we can enter it manually and press [USE PIN].
This means that from now on the applicaon will use the new PIN for connecons.
The [DOWNLOAD PIN] buon can be used to download a PIN saved in the database.
The read PIN code will be entered into the field,
but for the applicaon to use the new PIN code, press the [USE PIN] buon.
Changing the PIN code
To change the PIN code, make sure that the correct PIN code is entered in the yellow field above the [USE PIN] buon.
Then press the [CHANGE PIN] buon. We only provide the new PIN in the form that appeared. Aer entering the new PIN code,
press the [SET] buon. The PIN will be set and disconnected from the device just like aer changing the name.
Walls
The applicaon allows you to group devices into "walls". This makes it easier to filter those needed from all those
that are currently visible. To assign a device to a selected wall,
connect to it and then select the correct posion from the list of walls.
If the required posion is not there, create it in the wall wizard,
which is located below the [DOWNLOAD PIN] and [USE PIN] buons.
Aer creang a new posion, select it from the list of available walls and assign the device to the wall in this way.
You do not need to perform any addional operaons.
You can delete the wall from the database. Performing this acon will free all devices assigned to it. From now on,
they will only be visible when browsing all visible devices.
Navigating
Aer selecng the device from the list, the module control interface is shown and an aempt is made to connect to it.
If the connecon with the module fails, the applicaon returns to the device list. When establishing a connecon,
the selected buons are not acve. Only aer a successful connecon is it possible to control and configure the module.
To move the mechanism, hold the large buon with the white triangle.
The buon should be held unl the mechanism reaches the required posion.
If the technical condions make it impossible to maintain communicaon with the module,
it will automacally disconnect and return to the list of devices.
Simplified user manual module control application ZL-RC02.