Ego Power Plus SNT2410 User manual

OPERATOR'S MANUAL
56-VOLT LITHIUM-ION
CORDLESS
SNOW BLOWER
MODEL NUMBER SNT2410/SNT2410-FC
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
Español p. 93
Français p. 43

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC2
TABLE OF CONTENTS
Safety Symbols ..........................................4
Safety Instructions......................................5-6
Safe Operation Practices for Walk-behind Snow Blower........6-10
Introduction ............................................11
Specifications ..........................................11
Accessories ............................................12
Description .........................................13-15
Assembly ...........................................16-18
Operation ...........................................19-33
Maintenance ........................................34-38
Troubleshooting ......................................39-40
EGO Limited Warranty .................................41-42

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 3
READ ALL INSTRUCTIONS!
READ & UNDERSTAND
OPERATOR'S MANUAL
WARNING: Some dust created by power sanding, sawing, grinding, drilling
and other construction activities contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
◾Lead from lead-based paints
◾Crystalline silica from bricks and cement and other masonry products, and
◾Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC4
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them deserve your careful attention and
understanding. The symbol warnings do not, by themselves, eliminate any danger.
The instructions and warnings they give are no substitutes for proper accident
prevention measures.
WARNING: Be sure to read and understand all safety instructions in this
Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,”
and “CAUTION” before using this tool. Failure to follow all instructions listed below may
result in electric shock, fire, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION.
May be used in conjunction with other symbols or pictographs.
WARNING: The operation of any power tools can result in
foreign objects being thrown into your eyes, which can result in severe
eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields. Always use
eye protection which is marked to comply with ANSI Z87.1.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 5
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may appear on this product.
Read, understand, and follow all instructions on the machine before attempting to
assemble and operate.
Safety Alert Indicates a potential personal injury hazard.
Eye Protection
Always wear safety goggles or safety
glasses with side shields and a full face
shield when operating this product.
Read & Understand
Operator’s Manual
To reduce the risk of injury, user must read
and understand operator’s manual before
using this product.
DANGER —
Keep Hands Away
from the Impeller
Do not use hands to unclog the chute.
Keep Feet out of
Impeller Keep feet away from rotating impeller
KEEP HANDS AND FEET AWAY
GARDER MAINS ET PIEDS À DISTANCE
MANTENGA LAS MANOS Y LOS PIES ALEJADOS
DANGER — Keep
Hands and Feet
Away
To reduce the risk of injury, keep hands
and feet away from rotating parts. Do
not operate unless discharge chute is
in its proper place. If damaged, replace
immediately.
Recycle Symbols
This product uses Lithium-ion (Li-ion)
batteries. Local, state, or federal laws may
prohibit disposal of batteries in ordinary
trash. Consult your local waste authority for
information regarding available recycling
and/or disposal options.
IPX4 Ingress Protection
(IP) Rating
Classifies the degree of protection provided
by an enclosure, for electrical equipment.
V Volt Voltage

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC6
Direct Current Type or a characteristic of current
mm Millimeter Length or size
in. Inch Length or size
m Meter Length or size
ft Feet Length or size
kg Kilogram Weight
lbs Pounds Weight
PSI Pounds per square
inch Intensity of pressure
kPa Kilopascal Intensity of pressure
℉Degrees Fahrenheit Temperature
℃Degrees Celsius Temperature
WARNING: To ensure safety and reliability, all repairs should be performed by a
qualified service technician.
SAFE OPERATION PRACTICES FOR WALK-BEHIND
SNOW BLOWER
WARNING: This snow blower is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety instructions could result in
serious injury.
FOR ALL SNOW BLOWERS
◾Do not use on graveled surface unless the snow blower is adjusted for such a
surface in accordance with the operator’s manual.
◾Keep Children Away – All visitors should be kept a safe distance from work area.
◾Dress Properly – Do not wear loose clothing or jewelry. They can be caught in
moving parts.
◾Wear rubber boots when operating the snow blower.
◾Keep hands away from moving parts.
◾Keep guards in place and in working order.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 7
◾Don’t Force Snow Blower – It will perform better and safer at the rate for which it
was designed.
◾Don’t Overreach – Keep proper footing and balance at all times.
◾If the snow blower strikes a foreign object follow these steps:
1) Stop snow blower. Release the switch.
2) Remove the battery pack(s).
3) Inspect for damage.
4) Repair any damage before restarting and operating the snow blower.
◾Store Idle Snow Blowers Indoors - When not in use, snow blowers should be
stored indoors in dry, locked-up place – out of reach of children.
◾Maintain Snow Blowers with Care – Following instructions for lubricating and
changing accessories.
TRAINING
◾Read, understand and follow all instructions on the machine and in the
manual(s) before operating this unit. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop the unit and disengage the
controls quickly.
◾Never allow children to operate the equipment. Never allow adults to operate the
equipment without proper instruction.
◾Keep the area of operation clear of all persons, particularly small children.
◾Exercise caution to avoid slipping or falling, especially when operating the snow
blower in reverse.
PREPARATION
◾Thoroughly inspect the area where the equipment is to be used and remove all
doormats, sleds, boards, wires, and other foreign objects.
◾Do not operate the snow blower without wearing adequate winter garments.
Avoid loose-fitting clothing that can get caught in mowing parts. Wear footwear
that will improve footing on slippery surfaces.
◾Never attempt to make any adjustments while the motor is running (except when
specifically recommended by manufacturer).
◾Always wear safety glasses or eye shields during operation or while performing
an adjustment or repair to protect eyes from foreign objects that may be thrown
from the snow blower.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC8
OPERATION
◾Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to battery pack, picking up or carrying the snow blower. Carrying the
snow blower with your finger on the switch or energizing snow blower that has
the switch on invites accidents.
◾Do not put hands or feet near or under rotating parts. Keep clear of the discharger
opening at all times.
◾Exercise extreme caution when operating on or crossing gravel drives, walks, or
roads. Stay alert for hidden hazards or traffic.
◾After striking a foreign object, stop the motor, remove the battery pack(s),
thoroughly inspect the snow blower for any damage, and repair the damage
before restarting and operating the snow blower.
◾If the snow blower should start to vibrate abnormally, stop the motor and check
immediately for the cause. Vibration is generally a warning of trouble.
◾Stop the motor whenever you leave the operating position, before unclogging
the auger assembly housing or discharge chute, and when making any repairs,
adjustments or inspections.
◾When clearing, repairing, or inspecting the snow blower, stop the motor and
make certain the auger assembly and all moving parts have stopped. Remove the
battery pack(s) to prevent someone from accidentally starting the motor.
◾Exercise extreme caution when operating on slopes.
◾Never operate the snow blower without proper guards and other safety protective
devices in place and working.
◾Never direct the discharge toward people or areas where property damage can
occur. Keep children and others away.
◾Do not overload the snow blower capacity by attempting to clear snow at too fast
a rate.
◾Disengage power to the auger assembly when snow blower is transported or not
in use.
◾Use only attachments and accessories approved by the manufacturer of the snow
blower.
◾Never operate the snow blower without good visibility or light. Always be sure of
your footing, and keep a firm hold on the handles. Walk; never run.
◾Do not expose a battery pack or snow blower to fire or excessive temperature.
Exposure to fire or temperature above 265°F (130°C) may cause explosion.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 9
◾Disconnect the battery pack from the appliance before making any adjustments,
changing accessories, or storing appliance. Such preventive safety measures
reduce the risk of starting the appliance accidentally.
◾Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
◾Use the snow blower only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
◾When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together
may cause burns or a fire.
◾Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
◾Do not use a battery pack or appliance that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behavior resulting in fire, explosion
or risk of injury.
◾Follow all charging instructions and do not charge the battery pack or appliance
outside of the temperature range specified in the instructions. Charging
improperly or at temperatures outside of the specified range may damage the
battery and increase the risk of fire.
◾Have servicing performed by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the product is maintained.
◾Do not modify or attempt to repair the snow blower or the battery pack (as
applicable) except as indicated in the instructions for use and care.
◾Use only with the battery packs and chargers listed below:
BATTERY PACK CHARGER
BA1400, BA1400-FC,BA2800, BA2800-FC,
BA4200, BA4200-FC, BA1400T, BA1400T-FC,
BA2242T, BA2242T-FC, BA2800T, BA2800T-FC,
BA4200T, BA4200T-FC, BA3360T, BA3360T-FC,
BA5600T, BA5600T-FC, BA6720T, BA6720T-FC
CH2100, CH2100-FC,
CH3200, CH3200-FC,
CH5500, CH5500-FC,
CH2800D, CH2800D-FC
CH7000, CH7000-FC
NOTICE: For best performance and maximum run time, it is recommended to use two
5.0Ah or higher Ah battery packs.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC10
CLEARING A CLOGGED DISCHARGE CHUTE
Hand contact with the rotating auger assembly inside the discharge chute is the most
common cause of injury associated with snow blowers. Never use your hand to clean
out the discharge chute.
To clear the chute:
◾SHUT THE MOTORS OFF!
◾Remove the battery pack(s) from the snow blower.
◾Wait 10 seconds to be sure the auger assembly have stopping rotating.
◾Always use a clean-out tool, not your hands. Always use the chute cleaning tool
which is attached to the machine as an accessory, do not use your hand.
MAINTENANCE AND STORAGE
◾Check all bolts or fasteners at frequent intervals for proper tightness to be sure
the equipment is in safe working condition.
◾Always refer to operator’s manual for important details if the snow blower is to be
stored for an extended period of time.
◾Maintain or replace safety and instruction labels, as necessary.
◾Run the snow blower a few minutes after blowing snow to prevent freeze-up of
the auger assembly.
SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others
who may use this snow blower. If you lend this snow blower to someone else, also lend
these instructions to them to prevent misuse of the product and possibly injury.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 11
INTRODUCTION
Congratulations on your selection of a new generation of 56V Lithium-Ion powered
snow blower. It has been designed, engineered and manufactured to give you the best
possible dependability and performance.
Should you experience any problem you cannot easily remedy, please contact EGO
customer service center 1-855-EGO-5656.
This manual contains important information on the safe assembly, operation and
maintenance of your snow blower. Read it carefully before using the tool. Keep this
manual handy so you can refer to it at any time.
SERIAL NUMBER _____________________ DATE OF PURCHASE _________________
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE
PLACE FOR FUTURE REFERENCE.
SPECIFICATIONS
Voltage 56V
Clearing Width 24 in (610 mm)
Intake Height 20 in (508 mm)
Throwing Distance Up to 50 ft (15.2 m)
Ingress Protection Rating IPX4* (Protection from splashing water)
Wheel Size 15 in (381 mm)
Cold Tire Pressure 20 PSI (137.9 kPa)
Recommended Operating Temperature -4°F – 50°F (-20°C – 10°C)
Recommended Storage Temperature -4°F – 158°F (-20°C – 70°C)
Weight (without battery pack) 146.6 lb (66.5 kg)
* NOTE: IPX4 rating is valid when the battery compartment is properly closed.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC12
ACCESSORIES
WARNING: The following parts are subject to be worn out from normal use. Use
only identical replacement parts listed below. Use of parts that do not meet the original
equipment specifications may lead to improper performance and compromised safety.
PART NAME MODEL NUMBER
Shear Pin ASP2400
Shear Pin Set ASP2400D
Scraper Bar ASS2400
Skid Shoes (pair) (plastic sides) AKS2400D
Skid Shoes (pair)
(metal side + plastic side) AKS2800D
Chute Cleaning Tool ACT2400
Drift Cutter (pair) ADC2400

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 13
DESCRIPTION
KNOW YOUR SNOW BLOWER (Fig. 1)
1
Lock-off Button
Battery-Compartment Cover
Battery-Release
Button
Electric
Contacts
Ejection Mechanism
Power Indicator
Lock-off
Lever
Auger-Switch
Trigger
Heated Handle
Auger-Speed-
Control Lever
Self-Propel
Speed-Control
Lever
Heat On/Off
Button
Right Turn
Lever
Safety
Button
Headlights
Button
Heated Handle
Left Turn
Lever
Self-Propel
Trigger
Chute Direction/Pitch Control Handle
Handle Headlights
Chute Deflector
Snow-Discharge
Chute
Chute Cleaning Tool
Deck Headlights
Deck
Augers
Scraper Bar Skid Shoe (x2)
Wheel (x2)
Battery Compartment
Knob & Bolt (x 5)
Rear Handle
Cable Clamp

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC14
WARNING: The safe use of this product requires an understanding of the
information on the product and in this instruction manual, as well as knowledge of
the project you are attempting. Before use of this product, familiarize yourself with all
operating features and safety rules.
Safety Button (Power Up/Down)
The safety button must be pressed down before starting the auger rotation, self-propel,
handle heating, and headlights.
NOTE: It is not needed to press down the safety button if the power indicator shows
solid green, which means the safety button has been pressed down before.
WARNING: The safety button is a safety device. Never attempt to bypass its
operation.
Auger-Switch Trigger
Turns the auger motor ON and OFF.
Lock-Off Lever
Helps to prevent accidental and unauthorized activation of the auger-switch trigger. It
must be depressed before the auger-switch trigger can be activated.
Auger-Speed-Control Lever
Adjusts the auger speed which determines the throwing distance.
Self-Propel Trigger
Turns the self-propel function ON and OFF.
Self-Propel-Speed-Control Lever
Increases or decreases the self-propel speed.
Lock-off Button
Helps to prevent accidental or unauthorized operation of the chute direction/pitch
control handle. It must be depressed before the chute direction/pitch control handle can
be operated.
Chute Direction/Pitch Control Handle
With the lock-off button depressed:
◾Move the handle left or right to rotate the chute to direct the discharged snow as
desired. The handle allows the chute to rotate from 100° left to 100° right.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 15
◾Move the handle forward or backward to adjust the angle of the chute deflector,
which determines the pitch of the discharge stream and, in part, the throwing
distance.
Heated Handles
The gripping area could be heated by pressing the heat on/off button, to provide
warmth for the operator’s hands.
Heat On/Off Button
Turns the handle heating function ON and OFF.
Deck and Handle Headlights
These LED lights provide bright light for increased visibility.
Headlights Button
Turns the deck and handle headlights ON and OFF.
Power Indicator
Indicates the status of the snow blower and battery pack.
Right/Left Turn Lever
Disengages the right/left wheel from the self-propel motor to assist in making a right/
left turn when the snow blower is in self-propel mode.
Scraper Bar
Removes the last bit of snow from the surface you are cleaning.
Skid Shoe
Increases the ability to maneuver the snow blower on the snow and adjusts the
distance between snow scraper and ground.
Battery-Release Button
Press to release the battery quickly.
PEAK POWER™
This technology combines the power of up to two EGO 56V ARC Lithium™ batteries for
longer run time and efficient power draw.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC16
ASSEMBLY
WARNING: If any parts are damaged or missing, do not operate this product
until the parts are replaced. Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING: Do not attempt to modify this product or create accessories not
recommended for use with this blower. Any such alteration or modification is misuse
and could result in a hazardous condition leading to possible serious personal injury.
WARNING: To prevent accidental starting that could cause serious personal
injury, always remove the battery pack(s) from the tool when assembling parts.
UNPACKING
This product requires assembly.
◾Use two people to grasp the rear handle and the front part of the product at the
same time to carefully lift the tool up and out of the carton. Remove any other
accessories from the carton. Make sure that all items listed in the packing list are
included.
CAUTION: Heavy object. Team lift required. At least two persons are
required to be lift this snow blower out of the package.
WARNING: Do not use this product if any parts on the packing list are already
assembled to your product when you unpack it. Parts on this list are not assembled to
the product by the manufacturer and require customer installation. Use of a product
that may have been improperly assembled could result in serious personal injury.
◾Inspect the product carefully to make sure no breakage or damage occurred
during shipping.
◾Do not discard the packing material until you have carefully inspected and
satisfactorily operated the product.
◾If any parts are damaged or missing, please return the product to the place of
purchase.

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 17
PACKING LIST
PART NAME QUANTITY
Snow Blower 1
Handle Assembly 1
Snow-Discharge Chute Assembly 1
Knob & Bolt Set 5
Chute Cleaning Tool 1
Shear Pin 2
Operator’s Manual 1
INSTALLING THE HANDLE
ASSEMBLY (Fig. 2)
NOTICE: The handle assembly requires
assembly before operating the snow
blower (Fig. 2a).
Lift the handle assembly, align the holes
in the side rails with the holes in the rear
handle, select the preferred handle height,
then secure the handle assembly with
4 bolts and knobs (Fig. 2b). Please see
section “HANDLE HEIGHT ADJUSTMENT”
for detailed adjustment instructions.
2a
Handle
Assembly
Rear
Handle
2b
Side Rails
Bolt
Knob

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC18
NOTE: Four wire cables can be pulled
slightly towards the handle side to simplify
the assembly, if necessary (Fig. 2c).
INSTALLING THE SNOW-
DISCHARGE CHUTE ASSEMBLY
(Fig. 3)
WARNING: Never operate the
snow blower without the complete snow-
discharge chute in place.
1. Lift the snow-discharge chute assembly
and align the outer support pole with the
inner support pole (Fig. 3a).
2. Slide the outer support pole down until
the snow-discharge chute is fully seated
on the base.
3. Secure the snow-discharge chute
assembly with one knob and bolt (Fig. 3b).
NOTE: Four wire cables can be pulled
slightly toward the chute side to simplify
the assembly, if necessary (Fig. 3c).
3a
Outer
Support
Pole
Inner
Support
Pole
Base
Snow-
Discharge
Chute
3b
Knob & Bolt
3c
4 Wire Cables
2c
4 Wire Cables

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC 19
OPERATION
WARNING: Do not allow familiarity with this product to make you careless.
Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection with side shields marked to comply with
ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes and
other possibly serious injuries.
WARNING: Do not use any attachments or accessories not recommended by the
manufacturer of this product. The use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATION
You may use this product for the purposes listed below:
◾Removing snow from areas such as driveways and sidewalks.
CHUTE DIRECTION AND
DEFLECTOR ADJUSTMENT (Fig. 4)
WARNING: To prevent accidental
starting that could cause serious personal
injury, always remove the battery
pack(s) from the machine when making
adjustments.
NOTICE: Always pull the 4 wire cables
toward the handle side before operating
the chute direction/pitch control handle.
Otherwise, the wire cables may be
damaged due to overstretching (Fig. 4a).
NOTICE: Never attempt to secure the wire cable under the chute direction/pitch
control handle using cable/zip ties or any other fasteners. Avoid bending or twisting
this wire cable. Failure to follow this instruction will result in the loss of control over the
chute direction (Fig. 4a).
The chute can be adjusted to change both the direction and the throwing distance of
the discharged snow to assist you in moving snow away from one area and depositing
it in another.
4a
Cable Clamp
3 Wire Cables
1 Wire Cable
(under chute direction/pitch
control handle)

56V LITHIUM-ION CORDLESS SNOW BLOWER — SNT2410/SNT2410-FC20
The direction of snow discharge can be
adjusted up to 100° left and 100° right
(Fig. 4b).
1. Depress and hold the lock-off button.
2. Move the chute direction/pitch control
handle to the left or right to rotate the
chute to the left or right respectively.
The throwing distance of the snow
discharge is determined in part by moving
the chute deflector up or down (Fig. 4c).
1. Depress and hold the lock-off button.
2. To increase the distance that the snow
is thrown, pull the chute direction/pitch
control handle backward. This will lift
the deflector up.
To decrease the distance that the snow
is thrown, pull the chute direction/pitch
control handle forward. This will lower
the deflector down.
HANDLE-HEIGHT ADJUSTMENT
(Fig. 5)
WARNING: To prevent accidental
starting that could cause serious personal
injury, always remove the battery
pack(s) from the machine when making
adjustments.
The handle assembly can be set to three
different heights. Choose a comfortable
operating position according to your
height.
1. Loosen the two upper knobs and
pull out the two bolts. Save them for
reassembly.
1
2
4b
Chute Direction/
Pitch Control
Handle Snow-
Discharge
Chute
1
2
4c
Chute Direction/
Pitch Control
Handle
Deflector
5a
Side Rails
Upper Knob
& Bolt
Lower Knob
& Bolt