Yard-Man 31AE9P3I801 User manual

Operator's Manual
Two Stage
Snow Thrower
33" Model Shown
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
ForUSCustomers:MTD LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019
ForCanadian Customers: MTD Products Ltd., P.O.BOX1386, KITCHENEB,ONTARION2G4J1
PRINTED IN U.S.A. FORM NO. 769-01206A
(4/2005)

Content
CustomerSupport
ImportantSafeOperationPractices
Assembly
KnowingYourSnowThrower
OperatiingYourSnowThrower
TABLEOFCONTENTS
Page Content Page
2 Ajustments 12
3 Maintenance 13
5 Servicing 15
8 Off-Season Storage 18
10 Warranty 19
Illustrated Parts List 20
FINDINGMODELNUMBER
This Operator's Manual is an important part of your new snow thrower. It will help you to assemble, prepare and
maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new snow thrower, please locate the model plate on the
equipment and copy the information from it in the space provided below. The information on the
model plate is very important if you need help from our Customer Support Department or an
authorized dealer.
You can locate the model number by standing behind the unit in the operating position and looking down at
the dash panel. A sample model plate is explained below. For future reference, please copy the model
number and the serial number of the equipment in the space below.
Model Number Serial Number
Num#ro de module Num#ro de s#rier
XXXXXXXXXXX XXXXXXXXXXX
MTD LLC
&I_R'_'_ Rm_&I&_CLEVELAND, OH 44136
T_MI[._'M_N_IfMTD PRODUCTS LIMITED
........... _H.o KITCHENER, ON N2G 4Ji
USA-www,mtdproducts,com 1-800-800-7310
CAN-www.mtdcanada,com 1-800-668-1238
Copy the model number here:
Copy the serial number here:
ENGINEINFORMATION
The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating,
specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual
packed separately with your unit for more information.
CALLINGCUSTOMERSUPPORT
Please doNOTreturntheunittotheretailer fromwhichit waspurchased,withoutfirstcontactingCustomerSupport.
If you have difficulty assembling this product or have any questions regarding the controls, operation or
maintenance of this unit, please call a Customer Support Representataive.
For US Customers: 1- (330) 220-4MTD (4683) or 1- (800)-800-7310
For Canadian Customers: 1-800-668-1238
Please have your unit's model number and serial number ready when you call. See previous section to locate this
information. You will be asked to enter the serial number in order to process your call.

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could endanger the
personal safety and/or property of yourself and others. Read and follow all instructions in this manual before
attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you
see this symboliheed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to State of California to cause cancer and birth defects or other reproductive harm.
DANGER" This machine was built to be operated according to the rules for safe operation in this manual. As with
any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This
machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety
instructions could result in serious injury or death.
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place
for future and regular reference and for ordering
replacement parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75
feet from the machine while it is in operation. Stop
machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to
be used. Remove all door mats, newspapers, sleds,
boards, wires and other foreign objects which could be
tripped over or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair to
protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
3. Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other
loose clothing which could become entangled in moving
parts. Wear footwear which will improve footing on
slippery surfaces.
4. Use a grounded extension cord and receptacle for all
units with electric start engines.
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage the control handle before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator's manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite. Wash your skin
and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes before
refueling.
f. Never over fill fuel tank. Fill tank to no more than
1/2inch below bottom of filler neck to provide space
for fuel expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
i. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
j. Allow machine to cool at least 5 minutes before
storing.
Operation
1. Do not put hands or feet near rotating parts, in the auger
housing or discharge chute. Contact with the rotating
parts can amputate hands and feet.
2. The auger control handle is a safety device. Never
bypass its operation. Doing so, makes the machine
unsafe and may cause personal injury.
3. The control handle must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged discharge
chute. Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.

6. Donotoperatemachinewhileundertheinfluenceof
alcoholordrugs.
7. Mufflerandenginebecomehotandcancauseaburn.Do
nottouch.
8. Exerciseextremecautionwhenoperatingonorcrossing
gravelsurfaces.Stayalertforhiddenhazardsortraffic.
9. Exercisecautionwhenchangingdirectionandwhile
operatingonslopes.
10.Planyoursnowthrowingpatterntoavoiddischarge
towardswindows,walls,carsetc.Toavoidproperty
damageorpersonalinjurycausedbyaricochet.
11.Neverdirectdischargeatchildren,bystandersandpets
orallowanyoneinfrontofthemachine.
12.Donotoverloadmachinecapacitybyattemptingtoclear
snowattoofastofarate.
13.Neveroperatethismachinewithoutgoodvisibilityor
light.Alwaysbesureofyourfootingandkeepafirmhold
onthehandles.
14.Disengagepowertotheauger/impellerwhen
transportingornotinuse.
15.Neveroperatemachineathightransportspeedson
slipperysurfaces.Lookdownandbehindandusecare
wheninreverse.
16.Ifthemachineshouldstarttovibrateabnormally,stopthe
engine,disconnectthesparkplugandgrounditagainst
theengine.Inspectthoroughlyfordamage.Repairany
damagebeforestartingandoperating.
17.Disengagethecontrolhandleandstopenginebeforeyou
leavetheoperatingposition(behindthehandles).Wait
untiltheaugercomestoacompletestopbefore
uncloggingthedischargechute,makingany
adjustments,orinspections.
18.Neverputyourhandinthedischargeorcollector
openings.Alwaysuseaclearingtooltounclogthe
dischargeopening.
19.Useonlyattachmentsandaccessoriesapprovedbythe
manufacturer.
20.Ifsituationsoccurwhicharenotcoveredinthismanual,
usecareandgoodjudgment.Callcustomerassistance
forthenameofyournearestservicingdealer.
MaintenanceAndStorage
1. Never tamper with safety devices. Check their proper
operation regularly.
2. Disengage the control handle and stop engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting before cleaning, repairing, or
inspecting.
3. Check bolts, and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting orover-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original
equipment manufacturer's (O.E.M.) parts only. "Use of
parts which do not meet the original equipment
specifications may lead to improper performance and
compromise safety!"
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator's manual for
instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Observe proper disposal laws and regulations for gas,
oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator's manual for proper
instructions on off-season storage.
YourResponsibility:
• Restrict the use of this power machine to persons who
read, understand and follow the warnings and
instructions in this manual and on the machine.
eNEVER PUTHAND IN CHUTE. CAN
AMPUTATE HANDS AND FINGERS.
OSTOP ENGINEAND AUGERBEFOREUSING
CLEAN-OUTTOOL OR STICK.

SECTION2: ASSEMBLINGYOURSNOWTHROWER
NOTE: This Operator's Manual covers several models.
Snow thrower features vary by model. Not all
features discussed in this manual are applicable to all
snow thrower models.
LooseParts
The augers are secured to the auger shaft with two
shear pins and bow tie cotter pins. If you hit a
foreign object or ice jam, the snow thrower is
designed so that the pins may shear. Two
replacement shear pins and cotter pins are
provided for your convenience. See Figure 1. Store
these safely until needed.
Cotter
_L Shear Pins
Figure 1
IMPORTANT: NEVER replace the auger shear pins with
standard hex bolts. Any damage to the auger gearbox
or other components from using standard bolts will not
be covered by your snow thrower's warranty.
ItemsRequiredForAssembly
1. Pair of pliers
2. Engine oil
3. Fresh gasoline
BeforeAssembly
_, WARNING: Disconnect the spark plug wire
and ground it against the engine to prevent
unintended starting.
NOTE: Reference to the right hand or left hand side of
machine are observed from the operating position.
AssemblingHandle
• Remove the lower plastic wing nut, cupped washer
and carriage bolt from each side of the lower
handle. See Figure 2.
• Raise the upper handle assembly until it locks over
the lower handle.
• Look at the lower rear of the snow thrower frame to
be sure all the cables are aligned with the cable
roller guides. Make sure the spring (found at the
end of each cable) is attached to its actuator
bracket.
Upper Handle
Steering Cable
Tighten these
Wing
Lower Handle
Cable Tie_
_,Upper Shift Rod
Shift Rod
Con nector
Cupped
Washer
Wing
L_owerNut
Shift Rod
\\
Carriage
Bolt
NOTE: Support Tubes are omitted from the illustration for clarity.
Figure 2
• Secure the upper handle and lower handle with the
two plastic wing nuts, cupped washers and carriage
bolts previously removed.
• Tighten the two wing nuts already in place on the
upper holes and secure the handles firmly.
• Slide the shift rod connector down over the end of
the lower shift rod. Tap the connector until it locks
over the lower shift rod. See Figure 2.
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or direction.

AttachingtheChuteAssembly
NOTE: Your chute assembly may or may not be
assembled. If #requires assembly use the following
instructions.
jChute Assembly
Hex Screw
j._ J-f
\Hex Lock Nut
Chute Flange
Keeper
Figure 3
• Place chute assembly over chute opening, with the
opening in the chute assembly facing the front of
the unit. Place chute flange keepers beneath lip of
chute assembly, with the flat side of chute flange
keeper facing downward.
• Insert hex cap screws up through chute flange
keeper and chute assembly as shown in Figure 3.
Secure with hex flange Iocknuts. Tighten with two
7/16" wrenches. Do not over tighten.
AttachingChuteCrank
• Remove the hairpin clip from the upper chute crank
and slide the upper chute crank through the upper
chute crank bracket and into the lower chute crank.
A pair of pliers may help in this job.
4
Upper Chute Crank
/
rer Chute
_Crank Bracket
_''Hairpin Clip
_Lower Chute Crank
Figure 4
Align the two holes on both chute cranks and
secure with the hairpin clip removed earlier. See
Figure 4.
With the hex nuts loosened on the lower chute
crank bracket (see Figure 5) adjust the bracket so
that the spiral on the chute crank fully engages the
teeth on the chute assembly. Tighten the nuts on
the lower chute crank bracket securely.
\Chute Directional
_C ontrol
__2
Chute /_"-_ _/'-----_
Lower Chute__
Bracklet-_ r _ _/ --_
Lock Nuts
Figure 5
• The cable ties normally are loosely installed on
each side of the lower handle at the factory. Pull the
cable ties tight to secure. Trim excess from the
ends of cable ties.
• If not already attached, slip the cables that run from
the handle panel to the discharge chute into the
cable guide located on top of the engine.
See Figure 6.
Cables Cable
Guide
Figure 6
Wrap the wire from the head lamp down the right
handle until the wire can be plugged into the
alternator lead wire under the fuel tank.
Alternator Lead
NOTE: Wheels are omitted from illustration for clarity.
Figure 7

ChuteClean-OutTool
The chute clean-out tool is conveniently fastened to
the rear of the auger housing with a mounting clip.
Use the clean-out tool to clear snow and ice which
may lodge in the discharge chute during operation.
Refer to the Operation section for more detailed
information regarding the chute clean-out tool.
FinalAdjustments
Make these final adjustments before operating your
snow thrower for the first time. Failure to follow these
instructions may cause damage to the snow thrower.
WheelDriveControl& Shift Lever
Perform the followingtest to determine need for
adjustment:
• Move the shift lever into sixth (6) position. See
Figure 11.
• With the drive control released, push the snow
thrower forward, then pull it back. The machine
should move freely.
• Engage the drive control and attempt to move the
machine both forward and back, resistance should
be felt.
• Move the shift lever into the fast reverse (R2)
position and repeat the previous two steps.
If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the drive control
released, adjust the drive control immediately. To
adjust, proceed as follows:
• Loosen the jam nut on the traction control cable
and unthread the cable one full turn.
• Recheck adjustment.
• Retighten the jam nut to secure the cable when
correct adjustment is reached.
NOTE: For more details, refer to Wheel Drive Control
Adjustment in the Adjustment Section of this manual
AugerControl
Check the adjustment of the auger control as follows:
• When the auger control is released and in the
disengaged "up" position, the cable should have
very little slack, but should NOT be tight. See
Figure 8.
/Figure 8
_ ARNING: Do not over-tighten the cable.Over-tightening may prevent the auger from
disengaging and compromise the safety of the
snow thrower.
• In a well-ventilated area, start the snow thrower
engine as instructed on page 10. Make sure the
throttle is set in the fast position.
• While standing in the operator's position (behind
the snow thrower) engage the auger.
• Allow the auger to remain engaged for
approximately ten seconds before releasing the
auger control. Repeat this several times.
• With the engine running in the fast position and the
auger control lever in the disengaged "up" position,
walk to the front of the machine.
• Confirm that the auger has completely stopped
rotating and shows no signs of motion.
IMPORTANT:If the auger shows any signs of rotating,
immediately return to the operator's position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable.
• To readjust the control cable, unhook the spring
(found on the end of the auger cable) from the
auger actuator bracket. See Figure 9.
• Push the cable coupler through the end of the
spring to expose the lock nut. See Figure 10.
• Thread the lock nut outward (down the coupler)
three full turns to provide more slack in the cable
and reattach the spring to the bracket.
• Repeat auger control test to verify for proper
adjustment. Repeat previous steps to adjust more,
if necessary.
Auger Auger
Spring Actuator Bracket
Figure 9

Coupler
Spring
Cable
\ \ \
Lock Nut
Figure 10
Tire Pressure (PneumaticTires)
The tires are overinflated for shipping purposes.
• Check tire pressure. Maintain pressure between 10
and 14 psi.
NOTE: If the tire pressure is not equal in all tires, the
unit may pull to one side or the other.
_WARNING: Maximum tire pressure under
any circumstance is 30 psi. Equal tire pressure
should be maintained at all times. Excessive
pressure (over 30 psi) when seating beads
may cause tire/rim assembly to burst with force
sufficient to cause serious injury.
SECTION3: KNOWINGYOURSNOWTHROWER
_ ARNING" Be familiar with all the controls on the snow thrower and their proper operation. Know how tostop the machine and disengage them quickly.
Compare the Figure below with your equipment and be familiar with its controls before starting it.
Headlight
Wheel DriveControl/ /Shift Lever
Auger Control Lock //- Chute Tilt Control
FuelTank ,\ Auger Drive Control
\\
Oil Fill \
Discharge Chute Chute Crank
Chute Clean-Out Tool_ \ _ Wheel Steering
\ Control
\
Auger --_ Skid Shoe
Figure 11
DriveControl/AugerControlLock
The drive control is located on the right handle.
Squeeze the drive control to engage the wheel drive.
Release to stop.
This same lever also locks the auger control so you can
operate the chute crank without interrupting the snow
throwing process. If the auger control is engaged
simultaneously with the drive control, the operator can
release the auger control (on the left handle) and the
augers will remain engaged. Release the drive control
to stop the augers and wheel drive (the auger control
must also be released).
IMPORTANT: Always release the drive control before
changing speeds.

AugerControl
The auger control is located on the
left handle. Squeeze the auger
control to engage the augers.
Release to stop the snow throwing
action. The drive control must also be
released in order to stop auger.
ShiftLever
The shift lever is located in the center
of the handle panel and is used to
determine ground speed and
direction of travel. It can be moved
into any of eight positions.
IMPORTANT:Always release drive
control before changing speeds.
Forward: The snow thrower has six
forward (F) speeds. Position one (1)
is the slowest and position six (6) is
the fastest.
Reverse: The snow thrower has two
reverse (R) speeds--R1 isthe slower
of the two.
/
5--
4--
3--
2--
t--
DischargeChute
The angle of the discharge chute controls the distance
that the snow is thrown. Tilt the discharge chute up for
greater distance; tilt down for less distance.
ChuteCrank
The chute crank is located on the left
side of the snow thrower. Use it to
change the direction in which snow is
thrown. Avoid targetting persons,
animals or cars and buildings.
CLOCKWISE TO
DISCHARGE LIEFT
COUNTER CLOCKWISE
TO DISCHARGE RIGHT
ChuteTilt Control
The distance snow is thrown can be
changed by adjusting the angle of the
chute assembly. Move the chute tilt
control forward to decrease the
distance, toward the rear to increase.
WheelSteering Controls
The left and right wheel steering
controls are located on the underside
of the handles.
• Squeeze the right control to turn right; squeeze the
left control to turn left.
NOTE: Operate the snow thrower in open areas until
you are familiar with these controls.
Skid Shoe
The skid shoe position is determined by the condition of
the ground from where snow has to be removed. Higher
the snow level, lower will be the skid shoe. Adjust it
accordingly.
Headlight
The headlight is on whenever the engine is running.
ThrottleControl
The throttle control islocated on the engine Itregulates
the speed of the engine
SafetyIgnitionKey
The safety ignitionkey must be fully inserted inthe
switch before the unit willstart Remove key when snow
thrower isnot in use Do not attempt to turnthe key
ChuteClean-OutTool
The chute clean-out tool is designed to clear a clogged
discharge chute. Refer to page 11 for instructions on it.
_ARNING: Never use your hand to clear aclogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.

SECTION4: OPERATINGYOURSNOWTHROWER
BeforeStarting
Read and understand all instructions and warnings on
the machine and in this manual before operating.
Gas& OilFill-Up
•Service the engine with gasoline and oil as
instructed in the separate engine manual shipped
with the snow thrower.
_ WARNING" Use extreme care whenhandling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Never
fuel machine indoors or while the engine is hot
or running. Extinguish cigarettes, cigars, pipes
an other sources of ignition.
ToStartEngine
NOTE: If un# shows any sign of motion (drive or
augers) with the clutch grips disengaged, shut engine
off immediately. Readjust as instructed in the Final
Adjustments in the Assembly Section.
• Attach spark plug wire to spark plug.
•Make certain the auger and drive clutch levers are
in the disengaged (released) position. See Figure
6.
• Move throttle control up to FAST position.
• Insert ignition key into slot. Be certain it snaps into
place. Do not turn key.
NOTE: Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover.
ElectricStarter(optional)
WARNING: The electric starter is equipped
with a grounded three-wire power cord and
plug and is designed to operate on 120 volt AC
household current. It must be used with a
properly grounded three-prong receptacle at all
times to avoid the possibility of electric shock.
Follow all instructions carefully prior to
operating the electric starter.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician ifyou
are not certain.
If your house wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one
should be installed by a licensed electrician before
using the electric starter.
If you have a grounded three-prong receptacle,
proceed as follows:
Connect power cord to switch box on engine. Plug
the other end of power cord into a three-hole,
grounded 120 volt AC receptacle.
• Rotate choke knob to ON position.
• Push primer button three times,
as instructed in the engine
manual, making sure to cover
vent hole when pushing.
• Push starter button on top of the
engine to crank engine. As you
crank the engine, move choke
knob to FULL choke position.
Prime1_'t\
Vent Hole
• When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
• When disconnecting the power cord, always unplug
from the three-prong receptacle first and then from
the snow thrower.
RecoilStarter
• Rotate choke knob to FULL choke position (cold
engine start). If engine is warm, place choke in OFF
position instead of FULL.
• Push primer button two or three times. If engine is
warm, push primer button once only. Always cover
vent hole in primer button when pushing. At
temperatures below 15°F, additional priming may
be necessary.
• Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
• Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
• Repeat the previous steps until engine starts.
ToStopEngine
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To prevent possible freeze-up of starter:
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine
or starter. Disconnect the power cord from recepta-
cle first, and then from switch box.
Recoil Starter: With engine running, pull starter
rope with a rapid, continuous full arm stroke three
or four times. Pulling the starter rope will produce a
10

loud clattering sound, which is not harmful to the
engine or starter.
Move throttle control to "stop" or "off" position.
Remove ignition key. Do not turn key. Disconnect
the spark plug wire from the spark plug to prevent
accidental starting while equipment is unattended.
NOTE: Keep key in a safe place. Engine will not start
without ignition key.
• Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
control levers back and forth several times.
ToEngageWheelDrive
• With the engine running near top speed, move shift
lever to one of the eight positions to set desired
speed and direction. Select speed appropriate for
the snow conditions that exist.
NOTE: Use slower speeds in higher snow and/or until
you are familiar with the snow thrower operation.
• Squeeze wheel drive control against the right
handle to move the snow thrower; release it to stop.
IMPORTANT: NEVER move the shift lever without first
releasing the wheel drive control. Doing so will cause
premature wear on the drive system's friction wheel.
ToEngageAugers
• To engage augers and start snow throwing,
squeeze the auger control against the left handle.
• To disengage power to the augers, release both the
auger control and the wheel drive control, if
engaged.
OperatingTips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
_WARNING" The temperature of the muffler
and the surrounding areas may exceed 150°F
(65°C). Avoid these areas.
If possible, remove snow immediately after itfalls.
Discharge snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the shave plate for
normal usage. Adjust it upward for hard-packed
snow and downward when using on gravel or
crushed rock.
ChuteClean-OutTool
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Never
use your hand to clean a clogged chute or chute
opening; use this clean-out tool instead.
• Release both the wheel drive control and the auger
drive control levers.
• Stop the engine by removing the ignition key.
• Remove the chute clean-out tool from the clip
which secures it to the rear of the auger housing.
See Figure 12.
• Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the discharge chute.
• Re-fasten the clean-out tool to the mounting clip on
the rear of the auger housing and restart engine.
• While standing in the operator's position (behind
the snow thrower), engage the auger clutch lever
for a few seconds to clear any remaining snow or
ice from the discharge chute before continuing to
clear snow.
Chute Clean-Out Tool
Figure 12
11

SECTION5: MAKINGADJUSTMENTS
_ ARNING" NEVER attempt to clean chute
or make any adjustments while engine is
running.
ShiftRod
• Remove the hairpin clip and flat washer from the
shift handle under the handle panel. See Figure 13.
• Place shift lever in sixth (6) position or fastest
forward speed.
• Push shift arm assembly down as far as it will go.
• Rotate the ferrule up or down on the shift rod as
necessary until the ferrule lines up with the upper
hole in the shift lever. See Figure 13.
• Insert ferrule from the left side of the snow thrower
into the upper hole.
• Reinstall the hairpin clip and the washer.
IMPORTANT:Before operating the snow thrower, make
sure the shift rod is adjusted according to instructions
on page 7.
NOTE: For adjustment of auger control, skid shoe and
chute assembly, refer to Final Adjustments in Section 2,
Hairpin Clip
Flat Washer_
Upper Shift Rod
LowerShift_d__
_Shift Lever
Cc'UtCn ec t
Figure 13
WheelDriveControl
If you are uncertain about correct adjustment, proceed
as follows:
• Drain the gasoline out of your snow thrower's
engine, and place a piece of plastic film under the
gas cap to avoid spillage.
• Tip the snow thrower forward, allowing itto rest on
the auger housing.
• Remove the frame cover underneath the snow
thrower by removing six self-tapping screws.
• With the wheel drive control released, check ifthere
is clearance between friction wheel and drive plate
in all positions of the shift lever. See Figure 14.
• With the traction control lever engaged, check if the
friction wheel solidly contacts the drive plate. See
Figure 14. If not, adjust as follows:
• Loosen the jam nut on the traction drive cable and
thread the cable in or out as necessary.
• Retighten the jam nut to secure the cable when
correct adjustment is reached.
• Reassemble the frame cover.
• If you placed plastic film under the gas cap earlier,
remove it now..
Shift Arm er Cables
Auger Actuator
Bracket
DriveActuator
_Bracket
Hex Nut &
Cupped
Washer
Hex Gear
Drive Plate
"_ Rubber
Friction
Wheel
Figure 14
AugerControl
Refer to instructions on page 7 to adjust the auger
control. Make certain to check for correct adjustment
as instructed before operating the snow thrower.
ChuteAssembly
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Refer to
page 9for instructions.
The remote chute control cables have been pre-
adjusted at the factory. Move the remote chute lever on
the control panel back and forward to adjust angle of
the chute assembly.
12

SkidShoe
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes.
For close snow removal, as when using on a smooth
concrete or asphalt driveway, place the skid shoes in
the low position. Use the middle or high position when
the area to be cleared is uneven. When operating on
gravel, always put skid shoes in the high position.
See Figure 15.
Adjust skid shoes as follows:
• Loosen, but do not remove, the hex flange Iocknuts
which fasten the skid shoe to the auger housing.
• Raise or lower the skid shoe to desired position.
• Retighten the hex nuts loosened earlier.
NOTE: Make certain the bottom surface of skid shoe is
flat against the ground to avoid uneven wear.
• Repeat on the other side of the snow thrower.
Shave Plate
Skid
Shoes Hex Flange Locknuts
Figure 15
SECTION6: MAINTAININGYOURSNOWTHROWER
_ARNING: Before lubricating, repairing, orinspecting, disengage all clutch levers and stop
engine. Wait until all moving parts have come
to a complete stop. Disconnect the spark plug
wire and ground it against the engine to
prevent unintended starting.
GeneralRecommendations
• Always observe safety rules when performing any
maintenance.
• The warranty on this snow thrower does not cover
items that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, operator must maintain the snow thrower
as instructed in this manual.
• Some adjustments will have to be made
periodically to maintain your unit properly.
• Periodically check all fasteners and hardware to
make sure these are tight.
Lubrication
DriveandShiftingMechanism
• At least once a season or after every 25 hours of
operation, remove rear cover. Lubricate any chains,
sprockets, gears, bearings, shafts, and the shifting
mechanism at least once a season. Use engine oil
ora spray lubricant. Refer to Figure 14.
GearShaft
•Lubricatethe gear shaft with 6-in-1 grease (part
number 737-0170) at least once a season, or after
every 25 hours of operation. Refer to Figure 14.
IMPORTANT: Keep all grease and oil off the rubber
friction wheel and drive plate.
Engine
Refer to the engine manual for instructions.
GearCase
The gear case is lubricated with grease at the factory
and it does not require checking.
• If disassembled for any reason, lubricate with 2
ounces of Shell Alvania grease EPR00, part
number 737-0168. Before reassembling, remove
old sealant and apply new sealant.
IMPORTANT: Do not overfill the gear case, since
damage to the seals could result. Be sure the vent plug
is free of grease in order to relieve pressure.
AugerShaft
• At least once a season, remove the shear pins from
the auger shaft and spray lubricant inside the shaft.
See Figure 16.
IMPORTANT:Avoid spillage of oil on rubber friction
wheel and aluminum drive plate.
13

Shear Pin
_/ Cotter Pin
Vent Plug
Figure 16
DischargeChute
The base of the discharge chute and the spirals on the
chute crank should be lubricated at least every 25 hours
of use. Apply the lubricant under the base of the chute
and where the spirals contact the discharge chute. See
Figure 17.
Lube Under Chute Base Chute Crank Spirals
Figure 17
AugerBearingsandShaft
• Every season lubricate the auger bearings and the
bearings on the side of the frame with light oil. See to
Figure 16.
• Use oil or spray lubricant into the bearings at the
wheels at least once a season. Remove the wheels,
one side at a time, and clean and coat axles with
multi-purpose automotive grease.
• Lubricate the auger shaft at least once a season. To
do this:
• Remove the shear pins on the auger shaft.
• Oil or spray lubricant inside shaft.
• Carefully spin the auger around by hand to disperse
the lubricant.
• Reinstall the shear pins.
Wheel DriveControl /AugerControl Lock
The cams on the ends of the control rods which interlock
the wheel drive and auger drive controls must be
lubricated at least once a season or every 25 hours of
operation using a multi-purpose automotive grease. The
cams can be accessed beneath the handle panel. See
Figure 18.
anel
_/! _ LubeCams Here
Control Rods........... ,__
Figure 18
FrictionWheelRubber
Follow the instructions below to check the condition of
the friction wheel rubber every 25 hours of operation.
• Remove the six self-tapping screws from the frame
cover underneath the snow thrower.
• Visually inspect the friction wheel rubber for
excessive wear, cracks, or loose fit on the friction
wheel drive hub.
• Also engage the traction control and check ifthe
friction wheel is making contact with friction plate.
Refer to Figure 14. If it does not make contact,
adjust the traction drive cable and recheck the
friction wheel.
• Replace friction wheel rubber if necessary. Refer to
instructions on page 17.
DriveBelts
Follow the instructions below to check the condition of
the drive belts every 50 hours of operation.
• Remove the plastic belt cover on the front of the
engine by removing the three self-tapping screws.
• Visually inspect for frayed, cracked, or excessively
worn out belts.
• Replace belts as necessary as outlined in Service
Section on page 15.
Engine
Follow accompanying engine manual for all engine-
related maintenance issues.
14

SECTION7: SERVICINGYOURSNOWTHROWER
_ ARNING" Before servicing, repairing, or
inspecting, disengage all clutch levers and stop
engine. Wait until all moving parts have come
to a complete stop. Disconnect spark plug wire
and ground it against the engine to prevent
unintended starting.
Augers
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If you hit a foreign object or
ice jam, the snow thrower is designed so that the pins
may shear. Refer to Figure 16.
If the augers do not turn, check ifthe pins have
sheared. Two replacement shear pins and cotter pins
have been provided with the snow thrower. When
replacing pins, spray an oil lubricant into shaft before
inserting new pins.
ReplacingBelts
• Disconnect the chute crank assembly at the
discharge chute end by removing the hairpin clip
and the flat washer.
• Remove the plastic belt cover, located near the
engine, by removing the three self-tapping screws
and flat washers that secure it. See Figure 19.
• Remove the large shoulder bolt and washer on the
left hand side of the engine pulley. See Figure 20.
Hairpin Flat Belt Cover Belt Cover
Clip Washer Bolts,
IMPORTANT: NEVER replace the auger shear pins with
standard hex bolts. Any damage to the auger gearbox
or other components, as a result of doing so, will NOT
be covered by your snow thrower's warranty.
ShavePlateandSkidShoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. These should be
checked periodically and replaced when necessary.
NOTE: The skid shoes on this machine have two wear
edges. When one side wears out, they can be rotated
180° to use the other edge.
• Remove the six carriage bolts and hex flange
Iocknuts which attach two skid shoes to the snow
thrower on two sides. See Figure 15.
• Reassemble new skid shoes with the hardware
removed earlier. Make certain the skid shoes are
adjusted to be level.
• To remove the shave plate, remove the carriage
bolts and hex flange Iocknuts which attach shave
plate to the snow thrower housing.See Figure 19.
• Reassemble the new shave plate, with heads of
carriage bolts to the inside of the housing. Tighten
securely.
t \ Upper Bolt
\\ (remove)
Support Tube Bolt Shoulder Bolt
(do not remove)
Figure 19
AugerBelt
• Remove the hairpin clip and flat washer from the
ferrule in order to disconnect the auger idler rod
from the brake bracket assembly. See Figure 21.
• Slip the auger control belt (the front belt) off the
engine pulley. See Figure 21.
• Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable "Z" fitting.
• Remove the upper bolts and lock washers which
attach the auger housing assembly to the frame
assembly using a 9/16" wrench. Refer to Figure 19.
• Separate auger housing from the frame by tilting
the housing forward and pulling up the handles.
• Using a 1/2" wrench, remove the hex screw and
cupped washer from the center of the pulley on the
auger housing. Lift the brake bracket assembly out
of the pulley groove and remove the pulley. See
Figure 22. Be careful not to lose the key.
• Remove and replace auger belt inside belt keepers.
15

Engine Pulley
Shoulder Bolt
and Washer
ERe"
Pulley
Auger Idler
Brake
Assembly
Z Fittinc
Figure 20
_3_-_Auger Control
Belt
Cable Roller
DriveBelt
• Unhook the extension spring from the belt cover
plate. See Figure 23.
• Remove drive belt from the engine pulley and
bottom drive pulley.
• Replace belt and reassemble in reverse order.
Belt
Brake Bracket Assembly _uger Belt
Idler Pulley
m Q • a
HexScrew,
Cupped
Washer
Figure 22.
Belt Cover
/
/
/
Figure 21
• Reassemble pulley to auger housing with hex
screw and cupped washer (cupped side toward the
pulley). Make sure key is in place on shaft and
brake puck is seated in the pulley groove.
• Reassemble belt cover and chute directional
control.
Proper Adjustment: With the auger clutch lever in the
disengaged position, the top surface of the new belt
should be even with the outside diameter of the pulley.
• To adjust, disconnect ferrule from brake bracket
assembly and thread ferrule in (towards idler) to
increase tension on belt, and out to decrease tension.
NOTE: The brake puck must always be firmly seated in
the pulley groove when auger control is disengaged.
_,____ Extension
-. Spring
..........Drive Belt
Figure 23
• Reassemble the two halves of the unit hooking the
lower portion of the auger housing over the
stationary shoulder bolts in the frame assembly.
Secure the two halves with the two bolts and lock
washers removed earlier.
• Attach the "Z" fitting of the cable into the brake
bracket assembly. Refer to Figure 21.
• Slip the auger control belt over engine pulley.
• Insert ferrule on auger idler rod into bracket
assembly and secure with flat washer and cotter
pin. Reassemble the large shoulder bolt and lock
washer. Refer to Figure 20.
• Reassemble belt cover and chute crank.
16

ChangingFrictionWheelRubber
The rubber on the friction wheel is subject to wear and
should be checked after the first 25 hours of operation,
and periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.
• Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
• Tip the snow thrower up and forward, so that it rests
on the housing.
• Remove six screws from the frame cover
underneath the snow thrower.
• Remove the left wheel from the axle.
• Using a 7/8" wrench, hold the hex shaft and remove
the hex bolts and cupped washer and bearing from
left side of the frame. Refer to Figure 14.
• Holding the friction wheel assembly, slide the hex
shaft out of the left side of the unit. The spacer on
the right side of the hex shaft will fall and the
sprocket should remain hanging lose in the chain.
See Figure 24.
Shift Arm Assembly
• Insert the pin from the shift arm assembly into the
friction wheel assembly and hold assembly in
position. Refer to Figure 24.
Screw_
Hub
Plates
Bearing
Friction Wheel Rubber
Figure 25
• Slide the hex shaft through the left side of the
housing and through the friction wheel assembly.
• Insert the hex shaft through the sprocket and the
spacer. Make certain that the chain engages both
the large and the small sprocket.
NOTE: If the sprocket fell from the snow thrower while
removing the hex shaft, place the sprocket on the hex
shaft. Position the hex hub of the sprocket toward the
friction wheel when sliding the sprocket on to the hex
shaft. See Figure 26.
Figure 24
• Lift the friction wheel assembly out between the
axle shaft and the drive shaft assemblies.
• Remove four screws securing the friction wheel
rubber between the friction wheel plates. See
Figure 25. Discard old rubber.
• Reassemble the new friction wheel rubber to the
friction wheel assembly, tightening the four screws
in rotation and with equal force. SeeFigure 25. It is
important to assemble the rubber on the friction
wheel symmetrically for proper functioning.
Rex
Hex Hub Spacer
Figure 26
• Secure with the cupped washer and hex bolt
removed earlier.
• Secure the frame cover with six self-tapping
screws. Put the snow thrower down to its normal
operating position.
NOTE: If you placed plastic film under the gas cap, be
certain to remove #.
17

SECTION8: 0FF-SEASONSTORAGE
_ARNING" Never store engine with fuel in
tank indoors or in poorly ventilated areas,
where fuel fumes may reach an open flame,
spark or pilot light as on a furnace, water
heater, clothes dryer or other gas appliance.
•If unit is to be stored over 30 days, prepare engine
for storage as instructed in the engine manual.
• Remove all debris from the exterior of equipment.
• Follow lubrication recommendations on page 13.
• Always store the snow thrower in a clean, dry area.
NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.
SECTION9: TROUBLESHOOTING
Problem Cause Remedy
Engine fails to start.
Engine runs erratic.
Loss of power.
Engine overheats.
Excessive vibration.
Unit fails
to propel itself.
Unit fails
to discharge snow.
1. Fuel tank empty, or stale fuel.
2. Blocked fuel line.
3. Choke not in ON position
4. Faulty spark plug.
5. Safety key not in ignition switch on engine.
6. Spark plug wire disconnected.
7. Primer button not being used properly.
1. Unit running on CHOKE.
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
3. Exhaust port plugged.
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Traction control cable in need of adjustment.
2. Drive belt loose or damaged.
1. Discharge chute clogged.
2.
3.
4.
5.
Foreign object lodged in auger.
Auger control cable in need of adjustment.
Auger belt loose or damaged.
Shear bolt(s) sheared.
1. Fill tank with fresh gasoline.
2. Clean the fuel line.
3. Move switch to ON position
4. Clean, adjust gap or replace.
5. Insert the key fully into the switch.
6. Connect spark plug wire.
7. Refer to the engine manual.
1. Move choke lever to OFF position.
2. Clean fuel line and fill tank with clean, fresh
gasoline.
3. Drain fuel tank and carburetor. Refill with
fresh fuel.
4. Refer to the engine manual.
1. Connect and tighten spark plug wire.
2. Remove ice and snow from gas cap. Be
certain vent hole is clear.
3. Refer to the engine manual.
1. Refer to the engine manual or have the
carburetor adjusted by an authorized
engine service dealer.
1. Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and nuts. If
vibration continues, have unit serviced by
an authorized service dealer.
1. Adjust traction control cable. Refer to
Adjustments.
2. Replace drive belt.
1. Stop engine immediately and disconnect
spark plug wire. Clean discharge chute and
inside of auger housing.
2. Stop engine immediately and disconnect
spark plug wire. Remove object from auger.
3. Refer to Final Adjustments in Assembly
Section.
4. Refer to Adjustments.
5. Replace shear bolt(s).
NOTE: For repairs beyond minor adjustments listed above, contact the local dealer.
18

MANUFACTURER'S LIMITED WARRANTY FOR:
YaRD.MaNTM
®
Thelimited warranty setforth below is given byMTD LLCwith
respectto newmerchandise purchasedandused inthe United States
and/or its territories and possessions,and by MTDProducts Limited
with respectto newmerchandise purchasedandused in Canadaand/
or itsterritories and possessions (either entity respectively, "MTD").
MTDwarrantsthis product (excluding its normal wear partsas
describedbelow) against defectsin materialandworkmanship for a
period of two (2) yearscommencing on the dateof original purchase
andwill, at its option, repairor replace,free of charge,any partfound
to bedefective in materialsor workmanship. This limited warranty
shallonly apply if this product hasbeenoperatedandmaintained in
accordancewith the Operator's Manualfurnished with the product,
and has not beensubject to misuse,abuse, commercial use, neglect,
accident, improper maintenance,alteration, vandalism, theft, fire,
water, or damagebecauseofother peril or naturaldisaster. Damage
resulting from the installation or use of anypart, accessoryor
attachment notapproved by MTDfor usewith the product(s) covered
bythis manual will void your warrantyasto any resulting damage.
Normal wear partsarewarrantedto befreefrom defects in material
and workmanship for a period ofthirty (30) daysfrom the dateof
purchase. Normalwear partsinclude, but arenot limited to items
suchas: batteries, belts, blades,bladeadapters, grass bags,rider
deckwheels, seats, snowthrower skid shoes,friction wheels, shave
plates,augerspiral rubberandtires.
HOWTOOBTAINSERVICE:Warranty serviceisavailable,WITH
PROOFOFPURCHASE,through your localauthorized servicedealer.
To locatethe dealerin your area;
Inthe U.S.A.:
Checkyour Yellow Pages,or contact MTDLLCat P.O.Box361131,
Cleveland,Ohio44136-0019, or call 1-800-800-7310 or 1-330-220-
4683 or logon to our Websiteatwww.mtdproducts.com.
In Canada:
ContactMTDProducts Limited, Kitchener,ONN2G4J1, or call 1-
800-668-1238 or log onto ourWeb site atwww.mtdcanada.com.
This limited warranty does not provide coveragein the following
cases:
a. Theengine or component partsthereof. Theseitems
maycarry aseparatemanufacturer's warranty. Referto
applicable manufacturer's warrantyfor terms and
conditions.
b. Log splitter pumps, valves,andcylinders havea
separateone-yearwarranty.
c. Routinemaintenanceitems such as lubricants, filters,
bladesharpening,tune-ups, brakeadjustments, clutch
adjustments, deckadjustments, and normal
deterioration of the exteriorfinish dueto useor
d. Servicecompleted by someoneother thananauthorized
servicedealer.
e. MTDdoes not extend anywarranty for products sold or
exported outside ofthe UnitedStatesand/or Canada,
andtheir respectivepossessionsand territories, except
thosesoldthrough MTD'sauthorizedchannelsof export
distribution.
f. Replacementpartsthat arenot genuine MTD parts.
g. Transportation chargesand service calls.
h. IfProducts areused commercially. (MTD may
separatelyoffer Limited CommercialWarrantieson
certain selectproducts. Ask your dealeror retailerfor
details or contact MTD Servicefor more information.)
No implied warranty, including anyimplied warrantyof
merchantabilityof fitnessfora particularpurpose,appliesafter
the applicableperiodof expresswritten warrantyaboveasto the
partsas identified.No other expresswarranty,whetherwritten or
oral, exceptasmentionedabove, givenbyanypersonor entity,
includinga dealer or retailer, with respectto anyproduct,shall
bindMTD.Duringthe periodof thewarranty, the exclusiveremedy
isrepair or replacementof theproductassetforth above.
The provisionsasset forthinthis warrantyprovidethe soleand
exclusiveremedyarisingfrom thesale. MTD shallnothe liable for
incidentalor consequentiallossor damage including,without
limitation, expensesincurredforsubstituteor replacementlawn
careservicesor forrentalexpensestotemporarilyreplacea
warranted product.
Somejurisdictions do notallow the exclusion or limitation of
incidentalor consequential damages,or limitations on how long an
implied warranty lasts,sothe aboveexclusions or limitations maynot
apply to you.
In no eventshall recoveryof any kindbegreater thanthe amount of
the purchaseprice of theproduct sold. Alteration of safety features
ofthe product shall void this warranty. Youassume the risk and
liability for loss,damage,or injury to you and your property and/or to
others andtheir property arising out ofthe misuse or inabilityto use
the product.
This limited warranty shall not extendto anyone other thanthe
original purchaser or to the personfor whom it was purchased as a
gift.
HOWLOCALLAWSRELATETOTHIS WARRANTY:This limited
warranty givesyou specific legalrights, andyou mayalso haveother
rightsthat vary in different jurisdictions.
IMPORTANT:Ownermust presentOriginal Proof of Purchaseto
obtainwarranty coverage.
exposure.
MTDLLC, P.O. BOX361131 CLEVELAND,OHIO44136-0019; Phone: [phone]
MTDProductsLtd., P. O. BOX1386, KITCHENER,ONN2G4J1; Phone:[phone]
19

Forinformationonlightsandhandle
panelsrefertopages30and31./
Voir /es pages 30 et 31 pour tout
renseignement concernant le tableau de
bord et les phares.
63
31
Refer to assembly
instructions in the
owners manual
for correct
adjustment./
Consultez les
instructions
concernant le
reglage correct
dans la notice
d'utifisation.
34
3
24 94
51
40
42
103
51
8
30
19
24
5
27
1
102
Flats (#6) parallel to rear when installing engagement
handles in the engaged position as shown./
Placez les parties plates (#6) paraflelernent a I'arriere
lots de I'installation des manettes d'enclenchement a la
position engagee (representee).
8 29
A 63 32
103
52
56
51
23
31
93
61
54
53
77
@
20