EJEAS Q7 User manual

Q7
Top Quality Hi-Fi
Motorcycle Bluetooth Intercom
User manual
www.ejeas.com

Q7 is a cost-effective Bluetooth communication system
for motorcycle helmets. Qualcomm 5.0 chip is adopted
to quickly pair in one second. The maximum communi-
cation distance is 800 meters. It can realize seven
people switching and talking with each other. Standard
FM, it can automatically answer the phone, more conve-
nient and safe to use; Good waterproof performance,
can be used with confidence in rainy days; Optional
controller makes it easier for you to operate in cycling;
Specially designed stereoscopic sound effect allows you
to enjoy the fun of riding anytime and anywhere.
FM radio
Type-C Volume - Earphone
interface
A/C/E Switch Key
Volume +AntennaIndicator
B/D/F
Switch Key
Power/
Phone key
01
1. About Q7
English

Unscrew the screws of
the clamp & install it on
your helmet for fixed.
Install the Q7 model on
the slot of the clamp.
Use the Velcroto stick
inside of your helmet,
and choose the stick
mic/soft mic for your need.
Organize the inside
tangled cables & try to put
them in your inside helmet
foam for easy wearing.
1
2
3
4
2. Product Installation
02
English

3. Packing list
Host
Manual
Earphone EUC Handle
controller
Microphone Cable
Soft microphone
UNIVERSALCONTROLLER
Adapter:5V1A
SIN:EUC19070000
EJEASTechnologies.Inc
MabeinChina
Model
EUC
A/D
+
B/E
C/F
FM
Optional
Type-C
charging cable
Mounting clip
Q7
TopQuality Hi-Fi
Motorcycle Bluetooth Intercom
User manual
www.ejeas.com
Basic operation diagram
Single-click Double-click Triple-click
Long press for 5s Simultaneous click
5s
4. Operating instructions
03
EnglishEnglish

Pairing steps
2 models pairing
Auto searching & connecting
Pairing successful
"Intercom pairing successful"
"Intercom A connected"
Flashing blue at the same rate
Red & blue lights flash fast
alternately
"Intercom A pairing"
Blue light flashes
"Ding~Ding~Ding~Ding~"
Long press the A button for 5s
to enter pairing mode
Power on
2
3
4
1
All the following voice prompts are from the main device
5s
1s
04
ON
OFF
Blue light flashes
"Ding~Ding~Ding~Ding~"
Standby
Blue light flashes slowly
ON/OFF Please charge before use
1s
EnglishEnglish

05
main
main & sub-A
sub-B
sub-A
sub-Dsub-C
sub-Fsub-E
A button B button
Regard one Q7 as the main
device, the extra two models
as sub-machine
Power on
Red & blue lights flash fast
alternately
"Intercom A pairing"
Use the main device's "A" button
to pair with the sub-A's "A"
2
1
The main device allows to pair
with extra 6 intercoms. It's A-key
and B-key all could pair with 3 s
ub-machines. Use it's A-key to
pair the A sub-machine, C
sub-machine, & E sub-machine.
It's B-key to pair the B/D/F
sub-machine.
Auto searching & connecting
Pairing successful
"Intercom pairing successful"
"Intercom A connected"
3
4
5s
3 models pairing
Red & blue lights flash fast
alternately
"Intercom B pairing"
Use the main device's "B" button
to pair with the sub-B's "B"
5
Auto searching & connecting
Pairing successful
"Intercom pairing successful"
"Intercom B connected"
6
7
main & sub-A
5s
English

06
main & sub-C
Red & blue lights flash fast
alternately
"Intercom C pairing"
Use the main device's "A" button
to pair with the sub-C's "A"
8
Auto searching & connecting
Pairing successful
"Intercom pairing successful"
"Intercom C connected"
9
10
5s
4 models pairing
5 models pairing
main & sub-D
Red & blue lights flash fast
alternately
"Intercom D pairing"
Use the main device's "B" button
to pair with the sub-D's "B"
11
Auto searching & connecting
Pairing successful
"Intercom pairing successful"
"Intercom D connected"
12
13
6 models pairing
Use the main device's "A" button
to pair with the sub-E's "A"
14
Auto searching & connecting
Pairing successful
15
16
7 models pairing
Use the main device's "B" button
to pair with the sub-F's "B"
17
Auto searching & connecting
Pairing successful
18
19
5s
English

07
Blue light flash fast
"connecting Intercom B"
Flashing blue at the same rate
"Intercom B connected"
Talk to the sub-B
2
main
Each time intercom switching, you must disconnect the currently
pairing sub-machine
Blue light flash fast
"connecting Intercom F"
Flashing blue at the same rate
"Intercom F connected"
Talk to the sub-F
6
main
Blue light flash fast
"connecting Intercom D"
Flashing blue at the same rate
"Intercom D connected"
Talk to the sub-D
4
main
Blue light flash fast
"connecting Intercom E"
Flashing blue at the same rate
"Intercom E connected"
Talk to the sub-E
5
main
main
Blue light flash fast
"connecting Intercom C"
Flashing blue at the same rate
Talk to the sub-C
3
"Intercom C connected"
Switch the intercom connection
Talk to the sub-A
1
Blue light flash fast
"connecting Intercom A"
Flashing blue at the same rate
"Intercom A connected"
main
English

08
Open the phone connection
Turn on the Bluetooth on mobile,
click the "Q7"
Disconnect
"Pairing successful, connected"
"Phone pairing"
Pairing the phone/Disconnect with phone
Red & blue lights flash
Bluetooth
Q7
If there is no pairing connection, exit the pairing state after 2 minutes
1
2
3
5s
5s
Compatible with all EJEAS models
"Intercom A searching"
When pairing with other Bluetooth intercom or headset, you can
use intercom search for pairing connection
Click the A to search and pair
Regard Q7 as the main device,
the extra models as sub-machine
Power on
Pairing successful
"Intercom pairing successful"
"Intercom A connected"
Red & blue lights flash fast
alternately
Each device can become a host
"Intercom A pairing"
Use the two device's "A"
button to enter pairing mode
2
1
3
4
Blue light flashes quickly
Flashing blue at the same rate
main sub
5s
English

09
Disconnected Reset default setting
"Intercom Disconnected"
or
"Restore default setting"
1s1s 5s
or
Telephone answering
Automatic answer
when there is no
operation within
8 seconds
Hang up the call
Cancel the redial
Last Num Redial Call rejection
1s
or
Bluetoothback connection
Automatically
connect back to
the last phone
after switching on
English

English
10
When music is played
Switch song
1s 1s
Music play/paus
Make sure your phone supports
Bluetooth wake-up
Voice assistant
Bluetooth
awaken
or "hi~siri"
1s
When listening to FM
frequency+
frequency -
1s
1s
FM
Turn on/off the radio
Auto search & play radio, intercom & radio at the same time
76~108MHz
Turn on FM
Turn off FM
Blue light is on for 4 s
Red light flashes twice cycle instructions
"FM radio"
"FM radio off"
1s
TEL priority When listening to music/FM/intercom, receiving a call
Call Interrupt Hang up Restore
music FM intercom music FM intercom

English
11
Volume control
When listen to FM & intercom at the same time
Intercom volume
Intercom / talk /
music / FM FM volume
Power query In use
Charging indicator
Charging Constantly Red
Full The red light out
Low battery indication
Red light flashes twice
"Low battery"
"Battery level high"
"Battery level medium"
"Battery level low"
or
1s

English
12
5. Product Characteristics
Bluetooth Version: Bluetooth 5.0
Support:
Audio encoding format: SBC & AAC
Intercom mode:
Intercom communication distance: Up to 800 meters
Bluetooth headset communication distance: More than 10 meters
Temperature: Use temperature -10~50°C
Battery Parameter: 3.7V/750mAh
Electric Parameter: DC 5V/1A
Charge Time: About 3 hours
Endurance: 22 hours
Standby time: 260 hours
Charging interface: Type-C
Waterproof rating: IP65
Qualcomm®aptX™, cVc noisecancellation
technology 3D sound effects
Two-person intercom, can save
6 way switch intercom

Warning
1.
2.
3.
The use of this device on public transportation may not be
authorized by law. Please check your local laws and use this
product only in private Spaces or on closed roads.
If local law prohibits the use of both headphones while riding a
motorcycle, use only one headset while riding. If you do not
comply with this warning, the company does not accept any
responsibility.
Use this product at a high volume for a long time will cause
damage to your ears & hearing.Please keep the volume at an
appropriate level.
Attention
4.
7.
1.
2.
3.
5.
6.
8.
In order to ensure the communication distance when riding,
please try to use it in an open place.
If the electronic function fails, please power off and try again.
Installing equipment on the helmet is a modification of the helmet,
which may cause the helmet's warranty to fail or hinder the
helmet's function. This may cause danger in the event of
accidents, so please fully understand the facts when using the
helmet. If not, please return the product.
Before driving, please makesure that the product is firmly &
correctly mounted on the helmet. If the product falls off during
driving, it will cause injury oraccident.
To ensure riding safety, please use this product carefully while
on the road to avoid serious body injury, death or injury.
In the case of rain, please put the device jack down, USB rubber
plug tight; During use, ensure that the headphone jack is fully
plugged into the device to prevent water from entering the device.
The product contains 3.7V/750mAh battery. The battery capacity
will change with the temperature. When the battery is used at low
temperature or below 0°C, the battery life of the product may
attenuate to different degrees.
When using this product when operating vehicles or vehicles, the
safety precautions of the vehicle manufacturer must be observed.
13

Precautions for battery use
1.
2.
3.
4.
5.
6.
7.
8.
9.
Please do not put the discarded batteries together with the general
household garbage. In areas with relevant laws & regulations on
recycling & disposal of waste batteries, please follow the relevant
regulations of the local administrative department to make a
contribution to environmental protection.
Don't short-circuit the battery. A short circuit occurs when metal
objects (keys, jewelry, wires, COINS, or other conductors)
accidentally connect the positive & negative electrodes of a
battery. A short circuit can damage batteries or connectors & may
cause significant property damage or personal injury. Please keep
the charged batteries properly & do not leave them in your pocket,
wallet or other treasure bag with metal objects.
Do not put the battery on fire or place it in a hot place to avoid
leakage, overheating, bursting or fire.
Do not disassemble, weld or modify the battery. Do not place the
battery in a place with strong mechanical impact. Do not puncture
the battery with a hard object. Otherwise, the battery will leak,
overheat, burst or catch fire.
Do not remove, squeeze, heat or burn the battery inside the
product. It is strictly prohibited to use sharp objects, screwdrivers
or other devices to puncture or pry the battery. The above
operation may cause the battery to catch fire or burn.
The battery's electrolyte enters the eye & can lead to blindness.
If you splash the battery electrolyte into your eyes, do not rub your
eyes with your hands. Rinse thoroughly with water immediately &
contact the hospital for treatment. If the battery's electrolyte sticks
to the skin and clothes, wash them immediately with soapy water
& clean water, & seek medical attention if necessary.
Do not transfer batteries from other uses. Do not use any
damaged charger or battery. If the temperature of the battery is
too high during use, charging or storage, or abnormal phenomena
such as discoloration, deformation, bulging & leakage occur in the
battery, please stop using & replace the battery, so as not to
cause safety problems.
The battery is not waterproof, do not use or charge the battery in
the kitchen, bathroom & other high temperature & humidity places.
When charging, since the battery temperature will rise, please do
not put the battery & flammable objects (such as:bedside, clothes,
books, etc.) to avoidfire.
14

Safety Precaution
1. Keep out of reach of children and pets:
Please keep the products and all spare parts out of reach of
children and pets. Children or pets may swallow small parts that
can cause suffocation or other dangerous conditions.
2. Safe startup:
When it is forbidden to use electronic products or the use of
electronic products may cause interference or danger, please do
not turn on this product.
3. Pay attention to traffic safety:
Please comply with all relevant laws and regulations of the place
of use. Traffic safety should be taken into consideration when
using this product. Never use this product after drinking alcohol
or using drugs, or when you are extremely tired.
4. Interference:
All wireless product equipment may be interfered, which affects
its performance.
5. Shut down near medical devices:
Hospitals and health care facilities may see the use of
radio-frequency sensitive equipment.Please effectively follow
therules and regulations of any medical institution and turn off
the product when necessary.
6. Power off on an airplane:
Please comply with any restrictions related to aviation. The use
of wireless devices on the aircraft will interfere with the aircraft,
so please shut down the aircraft during flight.
7. Gas stations should shut down:
Do not use this product near a gas station (service station) or
where fuel or chemical agents are stored.
8. Power off near the blasting site:
Please observe any blasting regulations & don't use this product
in the place where blasting is performed
9. Accessories andbatteries:
Please use accessories and batteries approved by the company.
Using other accessories and batteries may damage the product
and cause danger.
10. Connect to other devices:
When connecting to other devices, please read the device's
instructions carefully for detailed safety instructions & correct
product operation. Do not connect incompatible products.
15

Environmental friendliness
Toxic and harmful substances or elements and content table
Toxic or harmful
substances or elements
Part name
Host Battery Accessories
XX
O O O
O O O
O O O
O O O
O O O
Plumbum (Pb)
Mercury (Hg)
Cadmium (Cd)
Polybrominated
Biphenyls (PBB)
Polybrominated
diphenyl ethers
(PBDE)
X
Chromium VI (Cr6+)
16

17
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliancecould
void the user's authority to operate the equipment. This device complies with Part15 of the FCC
Rules. Operation is subject to thefollowing two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this standard during product
certification for use next to the head with the minimum separation distance of 0mm is 0.1 W/Kg. This
transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.
This product is compliance to FCC RF Exposure requirements and refers to FCC website https://
apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: 2AIEB-Q7
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
caus harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: