Elecsky PL-606 User manual

- 1 -
PL-606
FM
FM
FM
FM stereo
stereo
stereo
stereo /
/
/
/ SW
SW
SW
SW /
/
/
/ MW
MW
MW
MW /
/
/
/ LW
LW
LW
LW DSP
DSP
DSP
DSP RECEIVER
RECEIVER
RECEIVER
RECEIVER
OPERATION
OPERATION
OPERATION
OPERATION MANUAL
MANUAL
MANUAL
MANUAL

- 2 -
CONTROL
CONTROL
CONTROL
CONTROL LOCATIONS
LOCATIONS
LOCATIONS
LOCATIONS
1. Power
2. Band* & ATS
3. VM & SCAN
4. VF & SCAN
5. ETM (Easy Tuning Mode)
6. Delete
7. Memory
8. Display & Lock & Snooze
9. FM ST. & AM BW
10. Alarm
11. Time
12. FM & SW Telescopic Antenna
13. FM & SW Antenna Jack
14. Earphone Jack
15. USB 5V DC-Jack
16. Multifunctional Tuning Knob
17. Stand
18. Volume Knob
19. Battery Compartment
The unit is shut down the long-wave band before out of the factory.If you want to open the long-wave band in
the off state, press MW button 10 seconds.
LCD
LCD
LCD
LCD DISPLAY
DISPLAY
DISPLAY
DISPLAY
1. Battery consumption indicator / Charging indicator
2. Sleep timer indicator
3. Alarm on/off indicator 4Key-lock indicator
5. Temperature (Temp.)
6. Signal indicators
dBu: signal strength unit
dB : Signal to Noise Ratio (S/N) unit
7. Alarm time indicator
8. SW meter band indicator
9. ETM indicator
10. Tuning speed:
" > " Slow Tuning
" >> " Fast Tuning
11. kHz: frequency unit for MW, LW & SW
MHz: frequency unit for FM
12. Digital number display (4 Digits)
With radio off: world time, alarm time, temperature
With radio on: word time, signal strength / SNR, alarm time, temperature, local time, memory address, meter band.

- 3 -
13. Preset memory address
14. Digital number display With radio off: local time
With radio on: frequency display, band display
15. Band indicator
16. FM stereo status indicator 17Rechargeable batteries indicator
HOW
HOW
HOW
HOW TO
TO
TO
TO TURN
TURN
TURN
TURN ON/OFF
ON/OFF
ON/OFF
ON/OFF THE
THE
THE
THE RADIO
RADIO
RADIO
RADIO
1. Open the battery compartment located on the back of the unit, install 2x AA alkaline batteries observing the
battery polarity diagram on the back of the radio. Close the battery door.
2. Press the [POWER] button to turn on/off the radio.
Note:
If the radio is unable to be turned on. Please check if the batteries were installed correctly, battery capacity is sufficient
or the lock function had been applied with " " displays
on screen (press & hold the [ ] button to unlock.)
TUNE
TUNE
TUNE
TUNE IN
IN
IN
IN STATIONS
STATIONS
STATIONS
STATIONS
Press the [POWER] button to turn on your radio, then select your desired band by pressing the [FM], [MW] SW[ ] or
[ ] button. In case of receiving FM/SW broadcasting, fully extend the telescopic antenna for a better reception.
When receiving MW(LW) broadcasting, please rotate the radio or change it's location to
achieve optimum reception. You can rotate the [VOLUME] knob to adjust to appropriate
volume from 0 to 30 levels.
Now, you can turn into your favorite stations with any of the below tuning methods:
METHOD
METHOD
METHOD
METHOD 1:
1:
1:
1: ETM
ETM
ETM
ETM (EASY
(EASY
(EASY
(EASY TUNING
TUNING
TUNING
TUNING MODE)
MODE)
MODE)
MODE)
ETM is the unique tuning method designed by Tecsun. It skillfully combines the reception
circuitry & control procedure to pre-select the suspected radio station and temporarily auto stores them into the ETM
memory (not the regular 550 memories). This highly enhances the efficiency when tuning into radio stations.
Employing ETM to tune preferred
frequencies. you can easily tune into your desired stations from those preferred frequencies.
1. Press the [ETM] button with [ETM] shows on screen to enter Easy Tuning Mode.

- 4 -
2. Press & hold the [ETM] button until the frequency start running to auto scan and store stations into ETM
memory, within the present band.
3. When the frequency stop running, turn around the [TUNING] knob to select those stored stations.
Notes:
Notes:
Notes:
Notes: While operating ETM to search for stations, a few stations might be missed if there is interference in the
surrounding. In this case, you can simply key-in the frequency, then press the [ETM] button to manually store it into
ETM memory.
T
T
T
T IPS
IPS
IPS
IPS :
:
:
:
FM
FM
FM
FM station:
station:
station:
station: When you are in a different city or country, you should perform the ETM function again in stead of
using ATS function, because this will not delete any of the stations already stored within the memory.
MW
MW
MW
MW station:
station:
station:
station: It is recommendable to perform the ETM function during night time, because there are usually many
stations starting broadcasting at night.
SW
SW
SW
SW station:
station:
station:
station: It is recommendable to perform the ETM function in the morning, afternoon as well as night time,
because the transmitting signal of SW is very unstable and usually there are more stations that start broadcasting in
the late afternoon.
METHOD
METHOD
METHOD
METHOD 2:
2:
2:
2: MANUAL
MANUAL
MANUAL
MANUAL TUNING
TUNING
TUNING
TUNING
Frequency
Frequency
Frequency
Frequency searching:
searching:
searching:
searching: Press the [VF] button to switch into frequency mode, and then rotate the [TUNING] knob to
select your desired station.
FAST/SLOW tuning is shown in the chart below for each band.
Band / Step
Slow tuning mode Fast
Fast
Fast
Fast tuning
tuning
tuning
tuning mode
mode
mode
mode
Turning step Turning
Turning
Turning
Turning step
step
step
step
FM 0.01MHz 0.1MHz
0.1MHz
0.1MHz
0.1MHz
MW 1kHz 9/10kHz
9/10kHz
9/10kHz
9/10kHz
LW 1kHz 9kHz
9kHz
9kHz
9kHz
SW
SW
SW
SW 1kHz
1kHz
1kHz
1kHz 5kHz
5kHz
5kHz
5kHz
Memory
Memory
Memory
Memory searching:
searching:
searching:
searching: Press the [VM] button to switch into memory mode, and then rotate the [TUNING] knob to
select those stored stations.
METHOD
METHOD
METHOD
METHOD 3:
3:
3:
3: AUTO
AUTO
AUTO
AUTO BROWSE
BROWSE
BROWSE
BROWSE STATION
STATION
STATION
STATION
1.Turn on the radio and press the [VF] button to switch into frequency mode.
2.Press & hold the [VF] button with [ ] advancing to scan from one station to another, staying on each station
for about 5 seconds.
3.To stop the auto browse function, simply press the [VF] button.
Note:
Note:
Note:
Note: While operating the
“
Auto Browse Station ” function, you can press the [M] button anytime to store the
station into memory, and the radio will keep on auto browsing the next available station.
WORKING
WORKING
WORKING
WORKING WITH
WITH
WITH
WITH STATION
STATION
STATION
STATION MEMORIES
MEMORIES
MEMORIES
MEMORIES
There are total 550 preset memories within the unit. 100 preset memories for each FM,
MW, and LW band, and 250 for SW.
FM
FM
FM
FM ATS:
ATS:
ATS:
ATS:
1. Fully extend the telescopic antenna and press the [FM] button to select FM band.

- 5 -
2. Press & hold the [FM] button with “ PRESET ” flashing and the frequency start running, then you can scan and
store your desired stations within the present band. When the frequency stop running, it means the ATS
operation has been completed; then rotate the [TUNING] knob for those scanned and stored stations.
MW/LW
MW/LW
MW/LW
MW/LW ATS:
ATS:
ATS:
ATS:
Press the [MW] button to select MW/LW band, then follow step 2 of FM ATS.
SW
SW
SW
SW ATS:
ATS:
ATS:
ATS:
Fully extend the telescopic antenna and press the SW [ ] or [ ] button to select SW band. There are two
modes for SW ATS tuning:
Mode
Mode
Mode
Mode A:
A:
A:
A: Press & hold the [ ] button to ATS the stations within all meter bands
Mode
Mode
Mode
Mode B:
B:
B:
B: Press & hold the [ ] button to ATS the stations within present meter band only.rotate the radio for
better location (MW & LW).
Notes:
Notes:
Notes:
Notes:
1. During ATS process in FM, MW / LW or SW (mode A), pre-stored radio stations will be replaced
automatically by the new searched stations.
2. With ATS in SW (mode B), those existing memories will not be replaced; all the newly found radio stations
would be stored in the blank memories addresses.
3. If there is too many interference in you surrounding or many mirror/blank station being stored during ATS,
you should contract the telescopic antenna (FM & SW) or rotate the radio for better location (MW & LW).
METHOD
METHOD
METHOD
METHOD 2:
2:
2:
2: MANUAL
MANUAL
MANUAL
MANUAL STORING
STORING
STORING
STORING STATON
STATON
STATON
STATON
1. Select band and tune to your desired station.
2. Press the [MEMORY] button with “ preset ” flashing
3. Press the [MEMORY] button again to store the station into memory. You can also wait for 3 seconds to
auto store the station into memory.
METHOD
METHOD
METHOD
METHOD 3:
3:
3:
3: SEMI-AUTO
SEMI-AUTO
SEMI-AUTO
SEMI-AUTO STORING
STORING
STORING
STORING STATION
STATION
STATION
STATION
While operating the “ Auto Browse Station ” function, you can simply press on the [MEMORY] button to store
the station into memory to avoid storing unwanted stations and
interfering signals.
Press the [VF] button to switch into frequency mode.
Press & hold the [VF] button with “ ” advancing to auto browse from one station to
another.
While tuning to your favor station, press the [M] button with “ PRESET ” flashing to
direct store the station into the next available memory. The unit will keep on browsing
until you deactivate it by pressing on the [VF] button again.
LISTENING
LISTENING
LISTENING
LISTENING TO
TO
TO
TO STORED
STORED
STORED
STORED STATIONS
STATIONS
STATIONS
STATIONS

- 6 -
METHOD
METHOD
METHOD
METHOD 1:
1:
1:
1: MANUAL
MANUAL
MANUAL
MANUAL MEMORY
MEMORY
MEMORY
MEMORY TUNING
TUNING
TUNING
TUNING
Press the press [VM] button to enter the frequency mode, then rotate the [TUNING] knob to tune into the stored station one
by one.
METHOD
METHOD
METHOD
METHOD 2:
2:
2:
2: AUTO
AUTO
AUTO
AUTO BROWSE
BROWSE
BROWSE
BROWSE MEMORY
MEMORY
MEMORY
MEMORY
1. Press the [VM] button with memory page shows in the upper right corner to enter the
frequency mode.
2. Press & hold the [VM] button until
“
PRESET ” flashing to auto scan from one memory to
another, staying on each station for about 5 seconds.
To stop auto search memory, simply press the [VM] button.
DELETE
DELETE
DELETE
DELETE MEMORY
MEMORY
MEMORY
MEMORY
METHOD
METHOD
METHOD
METHOD 1:
1:
1:
1: MANUAL
MANUAL
MANUAL
MANUAL DELETE
DELETE
DELETE
DELETE SINGLE
SINGLE
SINGLE
SINGLE MEMORY
MEMORY
MEMORY
MEMORY
1. Press the [VM] button to enter the memory mode.
2. Rotate the [TUNING] knob to select the memory that you want to delete.
3. Press & hold the [DELETE] button with “ dEL ” flashing; then press the [DELETE] button to
remove the unwanted memory address.
Note:
Note:
Note:
Note:
If “ dEL ” is flashing more than 3 seconds without confirmation, it will exit the delete function automatically.
METHOD
METHOD
METHOD
METHOD 2:
2:
2:
2: SEMI-AUTO
SEMI-AUTO
SEMI-AUTO
SEMI-AUTO DELETE
DELETE
DELETE
DELETE MEMORY
MEMORY
MEMORY
MEMORY
Feature: using the Auto-Browse function of memory to quickly delete unwanted station.
1. Press the [VM] button to enter the memory mode.
2. Press & hold the [VM] button with [PRESET] flashing to
auto scan from one memory to another, staying on each
station memory for about 5 seconds.
3. Once previewing your unwanted station, simply press the [DELETE] button with “ dEL ”
shows on display to delete the station, then keep on browsing other stations.
METHOD
METHOD
METHOD
METHOD 3:
3:
3:
3: MANUAL
MANUAL
MANUAL
MANUAL DELETE
DELETE
DELETE
DELETE ALL
ALL
ALL
ALL MEMORY
MEMORY
MEMORY
MEMORY WITHIN
WITHIN
WITHIN
WITHIN THE
THE
THE
THE BAND
BAND
BAND
BAND
1. Press the [VM] button to enter the memory mode.
2. Press & hold the [DELETE] button for 3 seconds and notices “ ALL ” flashing in the
upper right corner of display.
3. Press the [DELETE] button again to delete all memory within the selected band.
Note:
Note:
Note:
Note: If the [DELETE] button has not been pressed within 3 seconds to confirm, it
will exit the delete function automatically.
SLEEP
SLEEP
SLEEP
SLEEP FUNCTION
FUNCTION
FUNCTION
FUNCTION
1. Press & hold the [POWER] button with “ ” and “ 30 ” symbols show on the display.
2. Rotate the [TUNING] knob immediately to select sleep timer from 1 ~ 120 minutes or
select permanently “ On ” , then wait till the radio auto turn
on to confirm the setting.
Note:
Note:
Note:
Note:
The default setting of the auto-turn off time is 30 minutes.
CLOCK
CLOCK
CLOCK
CLOCK SETTING
SETTING
SETTING
SETTING
1.Press & hold the [TIME] button with hour flashing, then rotate the [TUNING] knob to adjust the hour.
2.Then press the [TIME] button with minutes flashing, and then rotate the [TUNING] knob to adjust the minute.

- 7 -
3. Press again the [TIME] button to confirm the setting.
Note:
Note:
Note:
Note: If the [TIME] button has not been pressed again within 3 seconds, the unit will automatically confirm the setting.
WORKING
WORKING
WORKING
WORKING WITH
WITH
WITH
WITH ALARM
ALARM
ALARM
ALARM
SETTING
SETTING
SETTING
SETTING THE
THE
THE
THE ALARM
ALARM
ALARM
ALARM TIME
TIME
TIME
TIME
1. Press & hold the [ALARM] button with hour flashing in the upper right corner, then rotate the [TUNING] knob to
adjust the hour.
2. Press the [ALARM] button with minutes flashing, then rotate the [TUNING] knob to adjust the minute.
3. Press the [ALARM] button again, then rotate the [TUNING] knob to select from 1 ~ 90 minutes to set the Auto Alarm
Off Timer.
4. Press the [ALARM] button to confirm the setting.
5. To turn off the alarm, press the [ALARM] button repeatedly with “ ” disappears.
Note:
Note:
Note:
Note: If the [ALARM] button has not been pressed again within 3 seconds, the unit will automatically confirm the alarm
setting.
HOW
HOW
HOW
HOW TO
TO
TO
TO SET
SET
SET
SET ALARM
ALARM
ALARM
ALARM BY
BY
BY
BY RADIO
RADIO
RADIO
RADIO
You can preset the alarm station following below steps:
1. Turn on the radio, then tune into your favorite station for alarm by radio and adjust your
desired alarm volume level.
2. Press the [MEMORY] button with “ PRESET ” flashing, then immediately press the
[ALARM] button and notice “ ” shows on the display to confirm the preset alarm station.
HOW
HOW
HOW
HOW TO
TO
TO
TO TURN
TURN
TURN
TURN OFF
OFF
OFF
OFF WHEN
WHEN
WHEN
WHEN ALARMING
ALARMING
ALARMING
ALARMING
Press the [POWER] button once to continuously listen to the radio; press it twice to turn it off.
Note:
Note:
Note:
Note: If the preset alarm is activated when you are listening to the radio, it will auto switch to the preset alarm station.
The unit will auto turn off after alarming.
SNOOZE
SNOOZE
SNOOZE
SNOOZE FUNCTION
FUNCTION
FUNCTION
FUNCTION
When the preset alarm is activated, you can press the [DISPLAY] button to temporarily turn off the alarm, the unit will
start alarming again 5 minutes later.
HOW
HOW
HOW
HOW TO
TO
TO
TO CHANGE
CHANGE
CHANGE
CHANGE THE
THE
THE
THE DISPLAY
DISPLAY
DISPLAY
DISPLAY MODE
MODE
MODE
MODE
With
With
With
With radio
radio
radio
radio OFF:
OFF:
OFF:
OFF: Repeat pressing the [DISPLAY] button to view Temperature or Alarm time
display.
With
With
With
With radio
radio
radio
radio ON:
ON:
ON:
ON: Press the [DISPLAY] button to view Local time, Alarm time, Temperature or
Signal strength/ SNR showing on the upper right corner of the display.
KEY-LOCK
KEY-LOCK
KEY-LOCK
KEY-LOCK FUNCTION
FUNCTION
FUNCTION
FUNCTION
Press & hold the [ ] button with “ ” symbol appears on the display to activate the key lock function.
Press & hold it again with the “ ” symbol disappears to deactivate the locking
function.
FM
FM
FM
FM ST.
ST.
ST.
ST. (FM
(FM
(FM
(FM STEREO)
STEREO)
STEREO)
STEREO)
While listening to FM stereo stations, press the [FM ST.] button with “ ” appears in the display to activate

Web: http://www.elecsky.com Email: [email protected]
- 8 -
the ” STEREO ” listening. If the received FM broadcast signal is too weak, it is recommendable to turn off the stereo
function by pressing the [FM ST.] button again with “ ” disappears.
Note:
Note:
Note:
Note: The stereo function will not be activated if the FM station is not stereo broadcasting.
AM
AM
AM
AM BW
BW
BW
BW (BANDWIDTH)
(BANDWIDTH)
(BANDWIDTH)
(BANDWIDTH)
Repeat pressing the [AM BW] button to select your desired 6, 4, 3, 2, 1 kHz bandwidth. Wide
Wide
Wide
Wide band:
band:
band:
band: It
has better audio fidelity when receiving strong signals or local stations. Narrow
Narrow
Narrow
Narrow band:
band:
band:
band: It is suitable to
receive weak & long distant station as narrow band is able to limit the interference from adjacent strong
signal and reduce the background noise.
SYSTEM
SYSTEM
SYSTEM
SYSTEM SETTING
SETTING
SETTING
SETTING
SETTING
SETTING
SETTING
SETTING FM
FM
FM
FM FREQUENCY
FREQUENCY
FREQUENCY
FREQUENCY RANGE:
RANGE:
RANGE:
RANGE: In radio off mode, press & hold the [FM] button until
87.5-108MHz, 64-108MHz, 76-108MHz, or 87-108MHz appears in the display. Quickly keep
pressing on the [FM] button to select suitable frequency range for your local FM.
TURN
TURN
TURN
TURN ON/OFF
ON/OFF
ON/OFF
ON/OFF THE
THE
THE
THE LW:
LW:
LW:
LW: With radio off, press & hold the [MW] button until “ LW ON ” or “ LW OFF
”
appears in the
display to turn ON or OFF the LW respectively.
HOW
HOW
HOW
HOW TO
TO
TO
TO TURN
TURN
TURN
TURN
ON
ON
ON
ON
/OFF
/OFF
/OFF
/OFF THE
THE
THE
THE INTELLIGENT
INTELLIGENT
INTELLIGENT
INTELLIGENT LIGHTING
LIGHTING
LIGHTING
LIGHTING
This machine has a smart lighting functions, using the buttons and knobs, the display lights will light for 3
seconds.
You can turn off or turn on smart lighting functions: Press and hold the [ ] button, lights flashes several
times, displays "OFF" and Close intelligent lighting function; Again Press and hold [ ] key, lights will
blinking several times, and displays "ON" symbol, The smart lighting function will open.
SETTING
SETTING
SETTING
SETTING MW(AM)
MW(AM)
MW(AM)
MW(AM) TUNING
TUNING
TUNING
TUNING STEP:
STEP:
STEP:
STEP: With radio off, press & hold [9/10kHz] button until "9kHz" or "10kHz"
appear in the display to select your desired AM tuning step
TEMPERATUE:
TEMPERATUE:
TEMPERATUE:
TEMPERATUE: When the AM tuning step is 10 kHz, the temperature displays will auto switch to Fahrenheit
(
℉
). When the AM tuning step is 9 kHz, the temperature displays will auto switch to Centigrade (
℃
).
TURN
TURN
TURN
TURN ON/OFF
ON/OFF
ON/OFF
ON/OFF THE
THE
THE
THE CHARGING
CHARGING
CHARGING
CHARGING FUNCTION
FUNCTION
FUNCTION
FUNCTION &
&
&
& EXCHANGE
EXCHANGE
EXCHANGE
EXCHANGE THE
THE
THE
THE BATTERY
BATTERY
BATTERY
BATTERY CONSUMPTION
CONSUMPTION
CONSUMPTION
CONSUMPTION DISPLAY:
DISPLAY:
DISPLAY:
DISPLAY:
With radio off, press & hold the [ ] key with “ ” & “ ” show up to activate the consumption display
of rechargeable batteries and the built-in charging system. Press & hold the [ ] key with “ “ shows up
and “ ” disappears to activate the consumption display of regular batteries and turn off the built-in charging
function.
Note:
Note:
Note:
Note: This radio is default to use regular batteries for power supply. In case of using rechargeable batteries, you
should switch the radio system to rechargeable batteries mode in order to show
the correct power capacity.
INTELLIGENT
INTELLIGENT
INTELLIGENT
INTELLIGENT CHARGING
CHARGING
CHARGING
CHARGING FUNCTION
FUNCTION
FUNCTION
FUNCTION
With radio off, install 2 x UM3 (AA) rechargeable batteries & then press & hold the
[ ] key with “ ” and “ ” display to activate the built-in charging

Web: http://www.elecsky.com Email: [email protected]
- 9 -
function.
Use 5V external adaptor with USB plug to connect with the radio.
The symbol “ ” will advance from the bottom to top during power
charging. It stops when batteries are fully charged.
Note:
Note:
Note:
Note:
Insist to use up all power of rechargeable batteries before charging
again. This could extend the life time of
battery and keep them in good
conditions.
2 pcs of batteries to be used as a group
and don't separate them for other
usage and mix to use batteries with
different power capacity.
Don't charge on any non-rechargeable
batteries in the radio, this will cause a hazard or damage to your
radio.
HOW
HOW
HOW
HOW TO
TO
TO
TO IMPROVE
IMPROVE
IMPROVE
IMPROVE FM
FM
FM
FM /
/
/
/ SW
SW
SW
SW RECEPTION
RECEPTION
RECEPTION
RECEPTION
METHOD
METHOD
METHOD
METHOD 1
1
1
1 :
:
:
:
Use connection type rod antenna improve FM /SW reception ability .
METHOD
METHOD
METHOD
METHOD 2:
2:
2:
2:
Plug in the external wire antenna to the [FM & SW] antenna jack of this radio, and then hang its end outside the
window for better reception of FM and SW.
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT MATTERS
MATTERS
MATTERS
MATTERS FOR
FOR
FOR
FOR USING
USING
USING
USING BATTERIES
BATTERIES
BATTERIES
BATTERIES
If no battery has been installed inside for long time, clock of radio would stop to work. However, pre-stored
frequencies are still kept. Clock would work again after new batteries being re-installed inside.
When the battery power is low, the " " symbol in the display will flash to alert you for changing new batteries.
Besides it will turns off automatically when the power is gone.
1. Mix using the used & new batteries would cause damage of radio and also display the capacity of power
incorrectly.
4. In case of radio not to be used for a long period, draw out the batteries for preventing liquid leakage and damaging
the parts of radio.
TROUBLE
TROUBLE
TROUBLE
TROUBLE SHOOTING
SHOOTING
SHOOTING
SHOOTING
QUESTIONS
QUESTIONS
QUESTIONS
QUESTIONS ANSWERS
ANSWERS
ANSWERS
ANSWERS SOLUTIONS
SOLUTIONS
SOLUTIONS
SOLUTIONS
Can not turn on the radio. -No power with the batteries.
-Didn't install the batteries properly.
-Power button is locked.
-Replace the new batteries.
-According to "+" or "-" sign to install
the batteries again.
-Press the [ ] button to unlocked.
Radio goes off when you are
listening.
-No power with the batteries.
-Sleep timer is activated.
-Replace the batteries.
-Turn on the radio again.
Can not store some stations using
ATS Some station store with
noise using ATS.
-Frequency of stations are too weak.
-There are interference near by your area.
-Search the station manually.
- Low down the antenna or move to
other location and try again.

Web: http://www.elecsky.com Email: [email protected]
- 10 -
Only limited FM stations can be
received in Japan.
-FM frequency is 76~90MHz for
Japan.
-Turn the radio off and press & hold
the [FM] button press [FM] button
again to select 76~108MHz.
Received very poor AM in USA. -USA is using 10kHz step for AM. -Turn off the radio press the [9/10kHz]
button to select 10kHz.
When the alarm activated (alarm
by radio), there is only noise with
the broadcast.
-Did not set the proper radio station for the
alarm.
-Or there are no broadcasting at that radio
station.
-Or you are in another city where does not
have a radio station for your preset
frequency.
-Preset your alarm station properly
(see the above setting).
-Make sure it has radio broadcast in
your location.
radio alfunction. This may caused by interference, and the
computer microchip not function properly.
Remove the battery, then you can
reload. If it is still not able to work,
please contact
your nearest dealer for customer
service.
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
Frequency range
FM
MW
LW
SW
87~108 MHz
Russia 64~108MHz
Japan 76~1 08 MHz
Eu, USA 87.5~108 MHz 522~1620 (USA 520~1710) kHz
153~513 kHz
2300~21 950 kHz
Sensitivity
FM (S/N=30dB)
MW (S/N=26dB)
LW (S/N=26dB)
SW (S/N=26dB)
Less than 3 μ V
Less than 1mV/m
Less than 10mV/m
Less than 20 μ V
Selectivity
FM
MW
LW
SW
＞60 dB ( ± 150kHz)
＞60 dB (BW=3kHz, ± 9kHz)
＞60 dB (BW=3kHz, ± 9kHz)
＞60 dB (BW=3kHz, ± 5kHz)
FM Stereo crosstalk Less than 25 dB
Memory 550
Output (Distortion 10%)
Speaker
Earphone Jack
≥ 230 mW
≥ 20 mW
Power
UM3 or AA X 2
USB 5V DC
Speaker φ 57mm, 250mW/8 Ohm
Earphone Jack φ 3.5mm, 32 Ohm, Stereo type
Dimensions Approx. 127(W) X 82(H) X 28(D) mm
Weight 175g (Batteries not included)