Electroconcept LS550-RGB3000 User manual

LS550-RGB3000
LASER PROJECTOR
INSTRUCTION MANUAL
Introduction :
Thank you for purchasing this Electroconcept product.
Please carefully read this manual before using this laser projector.
Responsibility :
On no account the Electroconcept company shall be held responsible for any damages of any
nature whatsoever, notably the operating loss, destruction of consumables (tape, disc, D) or
any other financial loss resulting from the use or the impossibility to use your equipment. In
addition Electroconcept shall not be held responsible for damages due to an improper use of
this product.
Warranty :
Electroconcept products have a 2 years manufacturer warranty (1 year for electronic, laser
sources, galvas and fan). The equipment shall be returned prepaid (at the customer's own
expense). Any freight collect will be refused. The equipment shall be returned in its original
packaging. The equipment's restitution will be at our own expense.
Are excluded from warranty: damages due to fault, negligence, lack of maintenance by the
user (broken, burnt, heated, wet, sandy...etc devices), already installed devices of which the
failure would originate from an improper installation or use by the customer.
This product is not intended for continuous use, in order to extend the lifetime of laser
sources please make a 10 minutes break per hour of continuous operation
(BLACKO T OR ELECTRICAL STOP)

TECHNICAL SPECIFICATIONS :
Power supply：A 230V ±10％
Frequency：50Hz～60Hz±10％
Power consumption：max 100W
Laser power specification : RGB 3000mW (~800mW Green, ~1000mW Red ,
~1500mW Blue)
Wave length : 520nm (Green)/638nm(Red)/450nm(Blue)
Laser class : lass 4
anaux DMX：14
ontrol signal：DMX-512 signal
Scanner :25K et 30K à 8°
ontrol mode : DMX-512, Stand-Alone, ,Sound to Music,ILDA、master and slave
Environment : Indoor use only
General safety instructions and warning notices
This laser is a LASS IV laser product .
This product has to be operated by trained laser operator.
Avoid eye or skin exposure to direct or scattered radiation.
Never look directly into a laser beam or directly into laser aperture when the laser projector is on.
Always stay focused during lasers operating in order to stop the laser projector if anything goes
wrong.
The user/owner is fully responsible for any damages caused by the laser projector, use it in
accordance with applicable laws in your country especially safety regulations laws and any
certification bodies.
Installation notice :
Before any use check that the product do not suffer during transport.
While installing the device, do not plug the power supply cord.
Do not use the laser projector outside, indoor use only.
Do not switch on the laser projector as soon as installed, wait for the laser projector to be at the
same temperature of the room to avoid condensation/moisture/mist to damage the product.
When rigging use safety cords able to resists ten times the weigh of the laser projector.
Rig the laser projector at least 50 cm away from any wall or flammable objects.
Do not cover the laser projector and place it away from heat sources like spotlights to ensure a
good air flow around the product.
At least laser beams should not hit anything under 3 meters from the floor level. Be attentive to
reflective surfaces.
The laser projector has to be easily stopped if necessary, ensure the power cord or circuit breaker
is accessible at anytime during the laser show. Do not use dimmers or electronic switch to power .
Refer to local laws for further instructions when operating the laser projector.
Warning : ! All connections have to be made with the laser projector switched off !
2

Operation :：
Internal laser service menu:
To navigate inside the service menu use « Enter » and « Return » switches
then + and – switches to change the value.
MODE:
SINGLE
Mode selection:
- DMX : DMX Mode / slave
- Single : Single logo selection
- Auto : Auto Mode / Sound to music Mode / Master
DMX adr:
1 Selection of DMX Address (for DMX mode) :
- from 1 to 512
TimeAuto
10 Sec Selection of transitional time between scenes when operating in
automatic mode
LogoRun
1 Selection of the logo in Single mode :
- from 1 to 255
Zoom :
12 General Zoom :
- from 50 to 128
Auto :
Prog 1 Selection of the internal program for Auto mode :
Prog 1/2/3
Sound :
On Activation of Sound to music Mode in Auto mode :
- On or Off
MicroS :
8 Sound detection sensibility level :
- from 0 to 60 (0 low sensitivity ,60 very high sensitivity)
InvX :
Off Reverse Pan X :
- on or off
InvY :
Off Reverse Tilt Y :
- on or off
USB Mode :
Mode USB
When connected to a computer with mini usb cable, you are able to use it realtime with the
MiniIlda Show Laser software Tm as well as download logos directly inside the laser memory.
Refer to MiniIlda Show Laser software notice to make these operations.
3

DMX Channels:
DMX Description
1 0 : OFF Mode
From 64 to 128 : AUTO Mode
From 129 to 192 : SOUND MODE
From 193 to 255 : DMX ONTROL
2 From 1 to 255 : LOGO ( INTERNAL MEMORY can be dowloaded via software)
3 From 1 to 255 : Stroboscope :0 none , 1 slow - 255 fast
4 Rotation : 0 none
From 1 to 128 : rotation angle
From 129 to 170 : lockwise speed
From 171 to 212 : Anti lockwise speed
From 213 to 255 : Ping Pong style rotation speed continuous « Ping Pong »
5 Zoom X: 0 none,
From 1 to 128 : Zoom X fixed
From 129 to 255 : Zoom X automatic speed Ping Pong style
6 Zoom Y: 0 none,
From 1 to 128 : Zoom Y fixed
From 129 to 255 : Zoom Y automatic speed Ping Pong style
7 Position X: 0 none,
From 1 to 128 : Position X fixed
From 129 to 255 : Position X automatic speed Ping Pong style
8 Position Y: 0 none,
From 1 to 128 : Position Y fixed
From 129 to 255 : Position Y automatic speed Ping Pong style
9 From 0 to 255 : General Analogical Zoom
10 From 0 to 255 : General motor speed from normal to slow
11 From 0 to 255 : Stop time on vector points from normal to slow
12 From 0 to 128 : Bind logos outside window
From 128 to 255 : rush logos outside window
4

13 olor palette from 0 to 15 palette 1 From 16 to 31 Palette 2 ,From 33 to …….
14 From 0 to 255 : olor Palette speed from slow to fast scrolling
ILDA Mode : (SubD-2 connector)
As soon as one ILDA hardware is connected through the SubD-25 connector , the laser
automatically switches to it and wait for instructions
Warning : ! All connections have to be made with the laser projector switched off !
DMX- 12 connection:
Only use a DMX cable and 3-pin XLR-plugs and connectors in order to connect the
controller with the fixture or one fixture to another :
Pin 1= Ground Pin 2 =Data (-) Pin 3 Data (+)
Connection between fixtures:
WARNING !
This product is not meant for a domestic use.
After unpacking the product, packaging materials (plastic bags, polystyrene, foam,…) must not be
left within children’s reach, this may be dangerous.
This product must be only used by an adult. Do not let a child use it or play with it.
Do not put this product under these conditions :
- In a damp location
- In a location subject to shock and vibrations
5

- In a location subject to extreme temperatures ( 45° /113°F or 2° /35.6°F )
Do not let any water, flammable liquids or metal objects enter the product.
In the event of liquids entering the product, unplug the power cable immediately.
Stop immediately using the device in the event of a serious functioning problem, and contact
your reseller for verification, or contact us directly.
Do not open the product. Any operation inside the console must be done by a qualified
technician.
SARL
ZA LA GARE
69620 HAMELET
FRAN E
TEL : [phone]
6