Electrolux EI30SM55JWA User manual

|NSTALLA'rioN INsrRucrIoNS
BEFORE YOU BEGIN Readtheseinstructionscompletelyandcarefully.
• _ Save these instructions for local
inspector's use.
• _ Observe all governing codes and
coordinates.
•NOTI;' TO iNSTALLER -Be sure to leave these
instructions with the Consumer.
•NOTE TO CONSUMER - Keep these instructions for
future reference.
•SKILL LEVEL- Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered
under the Warranty.
Please read all instructions thoroughly before installing
the Over the Range Microwave Oven. Two people are
recommended to install this product.
If a new electrical outlet is required, its installation should
be completed by a qualified electrician before the Over the
Range Microwave Oven is installed. See 3 ELECTRICAL
GROUNDING INSTRUCTIONS on page 2.
1 MOUNTINGSPACE
This Over the Range Microwave Oven requires a mounting
space on a wall as shown in Figure 1. It is designed to be
used with standard 12" wall cabinets.
Backsplash Atleast2"
30"or more
from cooking
surface
i
FiguPe 1
66" or more
from floor
2 WALLCONSTRUCTION
This Over the Range Microwave Oven should be mounted
against and supported by a flat vertical wall. The wall must
be flat for proper installation. If the wall is not flat, use spacers
to fill in the gaps. Wall construction should be a minimum of
2"x 4"wood studding and 3/8"or more thick dry wall or plaster/lath.
The mounting surfaces must be capable of supporting weight
of 110 pounds--the oven and contents--AND the weight of
all items which would normally be stored in the top cabinet
above the unit.
The unit should be attached to a minimum of one 2" x4"
wall stud.
To find the location of the studs, one ofthe following methods
may be used:
A. Use a stud finder, a magnetic device which locates the
nails in the stud.
B. Use a hammer to tap lightly across the mounting surface
to find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with
a small nail to find the edges of the stud and then placing a
mark halfway between the edges. The center of any adjacent
studs will normally be 16" or 24" to either side of this mark.
NEEDHELP?
For customers in the United States and Canada
United States: 1-800-944-9044
Canada: 1-800-265-8352
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
316495060
TINSEB196WBRZ-EL82
PrintedinThailand

3 ELECTRICALGROUNDINGiNSTRUCTiONS 4 HOODEXHAUSTDUCT
This appliance must be grounded. This oven is equipped with
a cord having a grounding wire with a grounding plug. It must
be plugged into a wall receptacle that is properly instaited and
grounded in accordance with the National Electrical Code and
local codes and ordinances. Inthe event of an electrical short
circuit, grounding reduces risk of electric shock by providing
an escape wire for the electric current.
WARNING - Improper use of the grounding plug can result in
a risk of electric shock.
ELECTRICALREQUIREMENTS
The oven is equipped with a 3-prong grounding plug. DO
NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE
THE GROUNDING PiN FROM THE PLUG.
DO NOT USE AN EXTENSION CORD. If the power supply
cord is too short, have a qualified electrician or serviceman
install an outlet near the appliance.
The Power Supply Cord and plug must be connected to
a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch
circuit, single grounded receptacle. The receptacle should
be located inside the cabinet directly above the Microwave
Oven mounting location as shown in Figure 2.
NOTE:
1. If you have any questions about the grounding or
electrical instructions, consult a qualified electrician or
serviceperson.
2. Neither Electrolux nor the dealer can accept any liability for
damage to the oven or personal injury resulting from failure
to observe the correct electrical connection procedures.
! /
Ground ......[_q i
/i Receptacle [_J
PowerCord
Figure2
When the hood is vented to the outside, a hood exhaust duct
is required. All ductwork must be metal; absolutely do not use
plastic duct. Check that all connections are made securely.
Please read the following carefully:
EXHAUSTCONNECTION:The hood exhaust has been designed
to connect to a standard 3 1/4"x 10" rectangular duct. If round
duct is required, a rectangular-to-round adapter must be
used.
REAREXHAUST: If a rear or horizontal exhaust is to be used,
care should be taken to align the exhaust with the space
between the studs, or wail should be prepared at the time it
is constructed by leaving enough space between wall studs
to accommodate exhaust.
MAXIMUM DUCT LENGTH:For satisfactory air movement, the
total duct length of 31/4" x 10" rectangular or 6" diameter round
duct should not exceed 140 feet.
Elbows, adapters, wall caps, roof caps, etc. present additional
resistance to air flow and are equivalent to a section of straight
duct which is longer than their actual physical size. When
calculating the total length, add the equivalent lengths of all
transitions and adapters plus the length of all straight duct
sections. Figure 3 shows the approximate feet of equivalent
length of some typical ductwork parts. Use the values in
parentheses for calculating air flow resistance equivalent,
which should total less than 140 feet.
90° Elbow(10ft.)
90° Elbow(25ft.)
G
45° Elbow(5ft.)
45° Elbow(5ft.)
Adaptor (5ft.)
Wallcap (40ft.)
10"WideElbow(10ft.)
Roof cap (24 ft.)
Figure3
® 2

5 7 PREPARATIONOFTHEOVENTOOLSRECOMMENDEDFOR
iNSTALLATiON
Phillips Screwdriver
Electric Drill
1/2",s/8"and 3/32"Drill Bits
1 1/2"Wood Bit or Metal Hole Cutter
(if metal cabinet is used)
Saw to cut exhaust opening (if needed)
Protective Drop Cloth for product and range -
you may also use carton for protection
Scissors
Pencil
Measure
Tape
6 INSTALLATIONHARDWARE
The INSTALLATION HARDWARE items (_ - @ are in a small
bag. All items are in a bag packed below the oven.
Item Name Quantity
<0 Wood Screw 5 x 35 mm 6
<2_ Toggle Bolt 3/16" 4
_3_ Top Cabinet Screw 5 x 85 mm 2
_4_ Flat Washer 30 mm diameter 2
<5_ Grommet 1
<6_ Tapping Screw 4 x 8 mm 3
<7_ Exhaust Damper Assembly 1
<s_ Grease Filter 2
<gb Rear Cushion 1
1. Open the bottom of the carton, bend the carton flaps
back and tilt the oven over to rest on plastic foam pad.
Lift carton off oven and remove all packing materials,
Installation Instructions, Wall Template, Top Template,
Turntable and Turntable Support; however, DO NOT
REMOVE THE WAVEGUIDE COVER, which is located
on the ceiling in the oven cavity. SAVE THE CARTON AS
IT MAY MAKE INSTALLATION EASIER.
2. CHECKTHE OVEN.
Check the oven for any damage, such as misaligned or
bent door, damaged door seals and sealing surfaces,
broken or loose door hinges and latches and dents inside
the cavity or on the door. If there is any damage, do not
operate the oven and contact your dealer or Electrolux
AUTHORIZED SERVICER.
___-_ MountingPlate
Figure5
,_6_ " ',z,
_,_ Usewlthmetalcabinets.Surround
'(5) _)_ thepowercordopening,Cuttofit,
_7_ I _ >
Figure4
Partsshownnottocommonscale,
3®

8VENTiLATiONSYSTEM
(PREPARINGOVENFOBiNSTALLATiON)
This Over the Range Microwave Oven is designed for
adaptation to three types of hood ventilation systems. Select
the type required for your installation.
RECIRCULATING-- non-vented, ductless. Follow installation
procedure (A). Recirculating requires the use of the
Charcoal Filters, which have already been installed in
the oven.
HORIZONTAL EXHAUST -- outside ventilation. Follow
installation procedure (B).
VERTICAL EXHAUST -- outside ventilation. Follow
installation procedure (C).
(A) RECIRCULATING:NON-VENTED,DUCTLESSOPERATION
The unit is shipped assembled for recircutating.
NOTE:
1. The Exhaust Damper Assembly is not required for
recircutating exhaust.
2. The Charcoal Filters should be replaced every 6 to 12
months, depending on use.
OvenLightCover
OvenLight
(B)
1.
2.
3.
4.
5.
6.
7.
HORIZONTAL EXHAUST: OUTSIDEVENTILATION
Remove 3 screws from back edge and 5 screws from the
top of Fan Cover Bracket. Save 3 screws to use them to
attach Exhaust Damper Assembly to the wall later and
discard remaining 5. Remove Fan Cover Bracket by
sliding it in the opposite direction of the arrow on the Fan
Cover Bracket, as shown in Figure 7.
Lift Hood Fan Unit carefully and slip wires out of cavity.
See Figure8.CAUTION:Do notpullorstretchHoodFan
Wire,
Rotate the Hood Fan Unit 180° so that the Fan Blade
Openings are facing the back of the oven. See Figure 9A on
page 5.
Replace Hood Fan Wire from (A) to (B). See Figure 9B
on page 5. Replace Hood Fan Unit into the oven. Be
careful not to pinch the Hood Fan Wire and the Hood
Fan Unit. See Figure 9C on page 5.
Put the wire back into cavity. See Figure 10A on page 5.
Assemble the Exhaust Damper Assembly to the Fan
Cover Bracket by sliding it into the slits in the same
direction as the arrow. Use 1 Tapping Screw 4 x 8 mm
from the INSTALLATION HARDWARE and tighten into
place. See Figure 10B on page 5.
This assembly will be mounted to the Outside Rear
Exhaust cutout in future instructions. See WALL
TEMPLATE for further procedures.
_ FanCoverBracket
Figure7
UpperTab
Figure GA
HoodLouver(inside)
Tabs
_--- ::,'_ HoodFanUnit-/
Hood w re... "....
/', t
fh
]
Figure8
j' j
FiguPeGB
®4

Rotate180° _-_ FanBladeOpenings
Changethepositionofwiretoleftsidehole
(B) (A)
HoodFanWire
Figure9C
(c)
1.
2.
3.
4.
5.
6.
VERTICALEXHAUST:OUTSIDEVENTiLATiON
Remove and save 3 screws from back edge and 5
screws from the top of the Fan Cover Bracket to use at
Step 5. Remove Fan Cover Bracket by sliding it in the
opposite direction of the arrow on the Fan Cover Bracket
as shown in Figure 11.
Lift Hood Fan Unit carefully and slip wires out of cavity.
See Figure 12. CAUTION:Do not pull or stretch HoodFan
Wire.
Rotate the Hood Fan Unit 90° so that the Fan Blade
Openings are facing the top of the oven. See Figure 13
on page 6. Replace Hood Fan Unit into the oven. Be
careful not to pinch the lead wire between the inner
bracket and the Hood Fan Unit. Put the lead wire into
Wire Box.
Replace the Fan Cover Bracket by sliding it into the slits
in the same direction as the arrow on the Fan Cover
Bracket. Make sure the fan blades are visible through
the top openings in the oven before proceeding. See
Figure 14 on page 6.
Attach the Fan Cover Bracket to unit with the 3 screws
from back edge and 5 screws from the top of the Fan
Cover Bracket, which were removed at Step 1 above.
See Figure 14 on page 6. The Hood Fan Unit is now
rotated for vertical exhaust operation.
Attach the Exhaust Damper Assembly to the fan cover
bracket on the top of the outercase cabinet after mounting
the oven. To attach the Exhaust Damper Assembly, refer
to MOUNTING OVEN TO THE WALL, See Figure 20 on
page 7 and TOP CABINET TEMPLATE.
FanCover Bracket
Exhaust Damper
Assembly
FanCover Bracket
ApplyRearCushion
afterExhaustDamper
Assemblyisscrewed
towail,
Savethe assembly for
future instructions.
[ Oven Rear Side ] Figure lOB
.J
IWall Side I
RearCushion
HoodFanWire
Figure11
HoodFanUnit
i'i,S " /
Figure12 ®

{B)
,, j' ,
Figure13
iiJ
3.
4.
Position the Mounting Plate with the Toggle Bolts
attached at the wall location and insert Toggle Nuts and
Bolts through the holes in the wall with the Toggle Nuts
closed. See Figure 16. Use Wood Screws to attach the
Mounting Plate to studs.
NOTE:Before insertion, be sure you leave a space more
than the thickness of the walt between the Mounting Plate
and the end of each of the Toggle Nuts (in the closed
position). If you do not leave enough space, the Toggle
Nut will not be able to open on the other side of the wall.
Also, once a Toggle Nut opens, it cannot be withdrawn
from the hole; therefore make sure all of the Toggles are
in the correct position before insertion.
Align the Mounting Plate carefully and hold in position
while tightening Toggle Bolts. Pull Toggle Bolt toward
you and turn clockwise to tighten. See Figure 17.
MountingPlate Figure 15
Figure14
9OVENINSTALLATION
THISOVENCANNOTBEPROPERLYINSTALLEDWITHOUTREFERRING
TOTHEMOUNTINGINSTRUCTIONSFOUNDONBOTHTEMPLATES.
THENEXTSTEPISTOREADANDFOLLOWMOUNTINGINFORMATION
ONBOTHTOPCABINETANDWALLTEMPLATES.
NOTE:THISOVENSHOULDBEATTACHEDTOATLEASTONEWALL
STUD.
MOUNTINGPLATE
1. Separate Toggle Nuts, packed in the INSTALLATION
HARDWARE, from 4 Toggle Bolts.
2. _ Use the mounting template
provided to Use wood screws to attach mounting
plate to the stud or studs. Use Toggle Bolts to
attach mounting plate through the holes at A, B, C
and D UNLESS THOSE HOLES ARE LOCATED ON
THE STUD. Insert one Toggle Bolt into A, B, C and
D where appropriate (these correspond to holes of
the Wall Template) and put the Toggle Nuts onto the
Toggle Bolts. See Figure 15. Refer to instructions in
Wall Template.
f
o ............................. o
•A ............ A
//
A C
MOUNTINGOVENTOTHEWALL
Two people are recommended to attach the Microwave Oven/
Hood to the Mounting Plate.
1. Thread the power supply cord through the hole made in
the bottom of the top cabinet.
2. Install the oven by tilting it forward and sliding it onto two
tabs of the Mounting Plate. Rotate the oven up so it rests
against the wall. See Figure 18 on page 7.
3. Use the two Top Cabinet Screws and two Flat Washers,
supplied in the INSTALLATION HARDWARE, to attach
the unit to the top cabinet. See Figure 19 on page 7.
4. Secure the bottom of the oven to the Mounting Plate
by using two Tapping Screws 4 x 8 mm from the
INSTALLATION HARDWARE. See Figure 19 on page 7.
® 6

i i
i i
i i
i i
i i
i i
Figure18
TopCabinet Screws
Tabs
CHECKLISTFORiNSTALLATiON
1. Make sure the unit has been installed according to all of the
Installation Instructions and the Wall and Top Cabinet Templates.
2. Plug in the power cord.
3. Keep these Installation Instructions.
NOTE:
Make sure to remove the tape at the turntable support before
operation. See figure 21.
Removethis tapebefore operation.
Figure 21
Tapping Screws
Figure19
TappingScrew
J
Figure20 7 ®

|HSrRU f NES DE INSTALAC|ON
ANTES DiE COMENZAR
_ Guarde estas instrucciones para uso del
inspector local.
Cumpla con los c6digos y normas vigentes.
• NOTA PARA EEL |NSTALADOR - Aseg0rese de
entregar estas instrucciones al consumidor.
•NO'rA AL CONSUM|DOR -Conserve estas
instrucciones para referencias futuras.
•N|V_L El!I_ CONOC|M|ENTO - La instalaci6n de este
aparato requiere de conocimientos b_.sicos sobre mec&nica
y electricidad.
Leaestasinstruccionescomp/etaydetal/adamente.
• La correcta instalaci6n es responsabilidad del instalador
• La garantia no cubre la falta del producto por instataci6n
inapropiada.
• Lea detenidamente las instrucciones antes de instalar el Homo
microondas sobre estufa. Se recomienda que ta instalaci6n de
este producto sea realizada entre dos personas.
• Si se requiere un tomacorriente electrico nuevo, su instalaci6n
debe ser realizada por un electricista calificado antes de
instalar el Homo microondas sobre estufa. Vea el capituto 3
INSTRUCClONES DE CONEXION ELECTRICA A TIERRA
en la pagina 2.
1ESPAC{0DEiVl0NTAJE
Este Horno microondas sobre estufa requiere de un espacio
de montaje en la pared como se muestra en la Figura 1. Esta.
diseRado para ser utilizado en gabinetes de pared esta.ndar
de 12".
{
A{ menos 2"
.................................;:._..........._==_ ......
I
i
i
i
i
30" 0 mas COn
respecto a {a
superficiede
lacocina
66" 0 m_s
conrespecto
a{piso
Figura1
2 CONSTRUCCIONDEPARED
Este Homo microondas sobre estufa debe montarse y
apoyarse en una pared vertical plana. La pared debe ser
plana para una instalaci6n apropiada. Si la pared no es plana,
utilice espaciadores para Ilenar los vacios. La construcci6n de
pared debe consistir de montantes de madera de 2" x 4" como
minimo y tablaroca o yeso/list6n de 3/8"o ma.s de espesor.
Las superficies de montaje deben ser capaces de soportar un
peso de 50 kg (110 libras) --el homo y su contenido--ADEMAS
de todos los elementos que generalmente se guardan en el
gabinete superior por encima de la unidad.
La unidad debe set fijada como minimo a un montante
de 2" × 4".
Para encontrar la ubicaci6n de los montantes, puede seguir
uno de los siguientes metodos:
A. Utilice un Iocalizador de montantes, un dispositivo
magnetico que Iocaliza los clavos en el montante.
B. Utitice un martitlo para golpear levemente la superficie
de montaje tratando de encontrar un sonido macizo. Esto
le indicara la ubicaci6n det montante.
El centro del montante puede ser ubicado sondeando la pared
con un pequeSo clavo para encontrar los bordes det montante
y luego cotocando una marca en el punto medic entre los
bordes. El centro de cualquier montante adyacente por Io
general estar& a 16" o 24" de cualquier lado de esta marca.
i,NECESITAAYUDA?
Para clientes en Estados Unidos y Canad& Ilame al
Estados Unidos :1-800-944-9044
Canada.: 1-800-265-8352
LEA CUIDADOSAMENTE. GUARDE ESTASINSTRUCOIONES.

INSTBUCCIONESDECONEXI6NATiEBBA
ELECTRiCA
Este aparato debe conectarse a tierra. Este homo esta
equipado con un cable que tiene un alambre de tierra y
enchufe con pata de tierra. Este debe enchufarse en un
tomacorriente de pared instalado apropiadamente y conectado
a tierra de acuerdo con el C6digo Electrico Nacional, y los
c6digos y ordenanzas locales. En caso que se produzca un
cortocircuito electrico, la conexi6n a tierra reduce el riesgo
de descarga electrica proporcionando un alambre de escape
para la corriente electrica.
ADVERTENCiA- El uso inapropiado det enchufe con pata de
tierra puede resuttar en petigro de descarga e lectrica.
BEQUEBllVilENTOSEL[:CTBICOS
El homo esta.equipado con un enchufe de conexi6n a tierra,
de tres patas. BAJO NINGUNA ClRCUNSTANClA CORTE O
RETIRE LA PATA DE TIERRA DEL ENCHUFE.
NO UTILICE EXTENSlONES DE CABLE. Si el cable de
alimentaci6n es demasiado corto, deje que un electricista
o tecnico calificado instale un tomacorriente cerca det
aparato.
El Cable de Suministro de Energia y el enchufe deben
conectarse en un tomacorriente conectado a tierra de
circuito separado de 120 Voltios AC, 60 Hz, 15 Amp, 6 m&s.
El tomacorriente debe ubicarse dentro del gabinete ubicado
directamente sobre el sitio de montaje del homo microondas
mostrado en la Figura 2.
NOTA:
1. Si tiene preguntas acerca de las instrucciones electricas o
de conexi6n a tierra, consulte un electricista calificado.
2. Ni Electrotux ni el distribuidor pueden aceptar ninguna
responsabitidad por dafio al homo o por lesiones personales
resultantes de no seguir los procedimientos correctos de
conexi6n electrica.
Tomacorriente
Conectadoa
Tierra
Orificio parael Cable
deEnergia
4DUCTODEESCAPEDECAIVlPANA
EXTBACTOBA
Cuando la campana extractora tiene escape hacia el
exterior, se requiere un ducto de escape de campana. Todo
el ducto debe ser met&lico, categ6ricamente no utilice ducto
pla.stico. Verifique que todas las conexiones esta.n sujetadas
firmemente. Por favor lea cuidadosamente Io siguiente:
CONEXION DE ESCAPE: El escape de la campana ha sido
disefiado para conectarse con un ducto rectangular estandar
de 3 W' x 10". Si se requiere ducto redondo, debe utilizarse
un adaptador de rectangular a redondo.
ESCAPETRASERO: Si debe utilizarse un escape trasero o
escape horizontal, debe tenerse cuidado de alinear el escape
con el espacio entre las cotumnas, o la pared debe prepararse
en el momento de construirse dejando suficiente espacio
entre las columnas de pared para acomodar el escape.
LONGITUD MAXIMA DEL DUCTO: Para movimiento satisfactorio
del aire, la Iongitud total det ducto rectangular de 3 W' x 10" 6
del ducto redondo con di_tmetro de 6" no debe exceder 140
pies (42.7 m).
Los codos, adaptadores, tapas de pared, tapas de techo,
etc., presentan resistencia adicional al flujo de aire y son
equivalentes a una secci6n recta de ducto con Iongitud
superior a su Iongitud fisica real. Cuando se calc ula la
Iongitud total, agregue las longitudes equivalentes de todas
las transiciones y adaptadores ma.s la Iongitud de todas las
secciones rectas de ducto. La Figura 3 muestra la Iongitud
equivalente aproximada en pies de algunas partes de ducto
tipicas. Utitice los valores dentro de parentesis para calcutar
la resistencia atflujo de aire equivalente que debe ser un valor
total inferior a 140 pies (42.7 m).
%
90 ° Codo (10 pies.)
90 ° Codo (25 pies.)
45 °Oodo (5 pies.)
45 °Oodo (5pies.)
Adaptador (5 pies.)
Tapa de Pared
(40 pies.)
Codo Anche de 10
pulgadas (10 pies.)
Tapa de Techo
(24 pies.)
Figura3
Figura2
® 2