Electrolux EMC3065X User manual

SOI 05.07 FV 599 38 84-81
SERVICE MANUAL
MICROWAVE OVENS
©ELECTROLUX HOME PRODUCTS
Corso Lino Zanussi,30
Publication No.
I - 33080 PORCIA /PN (ITALY) 599 38 84-81
Tel [phone]
Fax [phone]
SOI
Edition: 05.2007
EN/SERVICE/FV
Microwave Oven
EMC3065X (947608328)

PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a)Do not operate or allow the oven to be operated with the door open.
(b)Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs if necessary: (1) Interlock operation, (2) Proper door closing, (3)
Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and
latches (5) Evidence of dropping or abuse.
(c)Before turning on power to the microwave oven for any service test or inspection within the microwave
generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper
alignment, integrity, and connections.
(d)Any defective or misadjusted components in the interlock, monitor, door seal and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
TABLE OF CONTENTS
1. SAFETY AND PRECAUTIONS....................................................................................................................................3
2. SPECIFICATIONS ........................................................................................................................................................4
3. EXTERNAL VIEW.........................................................................................................................................................5
3-1. OUTER DIMENSION..........................................................................................................................................5
3-2. FEATURE DIAGRAM .........................................................................................................................................6
4. INSTALLATION............................................................................................................................................................7
5. CONTROL PANEL .......................................................................................................................................................8
6. DISASSEMBLY AND ASSEMBLY..............................................................................................................................8
7. INTERLOCK MECHANISM AND ADJUSTMENT.....................................................................................................18
8. TROUBLE SHOOTING GUIDE..................................................................................................................................19
9. MESUREMENT AND TEST .......................................................................................................................................24
9-1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT........................................................................24
9-2. MICROWAVE RADIATION TEST....................................................................................................................25
9-3. COMPONENT TEST PROCEDURE................................................................................................................26
9-4. COMPONENT ACTION....................................................................................................................................27
10. WIRING DIAGRAM...................................................................................................................................................28
2

1. SAFETY AND PRECAUTIONS
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may
cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a trained service personnel should make repairs.)
(1) A broken door hinge.
(2) A broken door viewing screen.
(3) A broken front panel, oven cavity.
(4) A loosened door lock.
(5) A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN.
The microwave oven has concealed switches to make sure the power is turned off when the door is opened.
Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. FOR SAFE SERVICE PROCEDURES.
1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the
oven.
2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the
oven.
(1) inform the manufacturer, importer or assembler,
(2) repair the unit at no cost to the owner,
(3) attempt to ascertain the cause of the excessive leakage,
(4) tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact
the manufacturer immediately.
IMPORTANT
The wire in this mains lead coloured in accordance with the following code.
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the
letter E , earth symbol or coloured green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
NOTE : This oven is designed for counter-top use only.
3

4
MODEL KOC-9N4T7S, 9N4T7S24, KOC-9N5T7R
9N5T7S, 9N5T7S21
POWER SUPPLY 230V~50Hz, SINGLE PHASE WITH EARTHING
MICROWAVE 1450W
POWER CONSUMPTION GRILL 850W
CONVECTION 2250W 1450W
COMBINATION 2950W 1450W
MICROWAVE ENERGY OUTPUT 900W (IEC 705)
MICROWAVE FREQUENCY 2450MHz
OUTSIDE DIMENSIONS (W X H X D) 542X329X515mm(21.3X13.0X20.3 in.)
CAVITY DIMENSIONS (W X H X D) 350X230X355mm(13.8X9.1X14.0 in.)
NET WEIGHT Approx. 18Kg (39.6 lbs.)
TIMER 60 minutes
FUNCTION SELECTIONS Microwave / Grill / Convection / Combination
POWER SELECTIONS 10 LEVELS
CAVITY VOLUME 1.0 Cu. Ft
* SPECIFICATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.
2. SPECIFICATIONS

5
3. EXTERNAL VIEW
1. OUTER DIMENSION
1)KOC-9N4T/9N5T

6
11. DOOR HOOK
When the door is closed, it will automatically lock shut. If door is opened while oven is operating, the magnetron
will immediately stop operating.
12. DOOR VIEWING SCREEN
Allows viewing of food. The screen is designed so that light can pass through, but not the microwave.
13. METAL RACK
14. TOP HEATER
Turns on when convection, grill and combi cooking is selected.
15. OVEN LAMP
Automatically turns on during oven operating.
16. SAFETY INTERLOCK SYSTEM
17. CONTROL PANEL
18. TURNTABLE TRAY
Rotates during cooking and ensure even distribution of Microwaves.
It can also be used as a cooking utensil.
19. ROLLER GUIDE
This must always be used for cooking together with the turntable tray.
10. COUPLER
This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.
11. CONVECTION OUTLET & FAN
12. OVEN FRONT PLATE
13. DOOR SEAL
Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage.
14. BARBECUE BAR (KOC-9N7T7SA2 ONLY)
This is used barbecue cooking.
2. FEATURE DIAGRAM

1. Steady, flat location
This microwave oven should be set on a steady, flat surface.
This microwave oven is designed for counter top use only.
2. Leave space behind and side
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually,
cause failure.
3. Away from Radio and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, Radio, antenna or feeder
and so on.
Position the oven as far from them as possible.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.
5. Power supply
Check your local power source. This microwave oven requires a current of approximately 13 amperes, 230V, 50Hz.
Power supply cord is about 1.0 meters long.
The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other
accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage
resulting from use of this oven with a voltage of ampere fuse other than those specified.
This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type.
Such a cable can be purchased from DAEWOO and must be installed by a Qualified Person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7. Do not operate the oven if it is colder than room temperature.
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by
providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing wire with a
earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
4. INSTALLATION
EARTHING INSTRUCTIONS
WARNING
Improper use of the earthing plug can result in a risk of electric shock.
Consult a qualified electrician of serviceman if the earthing instructions are not completely understood, or if doubt
exists as to whether the appliance is properly earthed, and either:
If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a
3-slot receptacle that will accept the plug on the appliance.
The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or
Do not use an extension cord.
7

8
5. CONTROL PANEL
11Display : Cooking time, power level, indicators and
present time are displayed.
MW : When blinking, the oven is operating in
MICROWAVE COOK.
Grill : When blinking, the oven is operating in GRILL.
Combi : When blinking, the oven is operating in COMBI.
Defrost Weight : When blinking, the oven is operating in
WEIGHT DEFROST.
Time : When blinking, the oven is operating in TIME
DEFROST.
Auto-cook : When blinking, the oven is operating AUTO
COOK.
Lock : When lighting, the oven is CHILD LOCK.
Con-vection : When blinking, the oven is operating in
CONVECTION.
g : When blinking, the oven is operating in weight input
mode.
Barbecue : When blinking, the oven is operating in
barbecue. (KOC-9N7T7SA2 only)
22Auto cook : Used to cook or reheat.
33Combi : Used to select combi.
44Weight Defrost : Press to select the weight defrosting
cooking. (KOC-9N4T7S/9N4T7S24/9N5T7S/9N5T7R/
9N5T7S21/9N7T7S/9N7T7S21 only)
Auto Defrost : Press to select the auto defrosting
cooking. (KOC-9N7T7SA2 only)
55Grill : Used to select grill.
66MW : Used to set power level of micro wave.
77Time Defrost : Press to select the time defrosting
cooking. (KOC-9N4T7S/9N4T7S24/9N5T7S/9N5T7R/
9N5T7S21/9N7T7S/9N7T7S21 only)
Barbecue : Press to select the barbecue cooking.
(KOC-9N7T7SA2 only)
88Convection : Used to select convection and selected
temp.
99Clock : Used to set clock.
00Dial knob : Used to set time, weight and quantity.
qqSTART/SPEEDY COOK : Used to start a programmed,
also for speedy start(each press adds 30 seconds
microwave cooking time).
wwSTOP/CLEAR : Used to stop the oven operation or to
delete the cooking data.

6. DISASSEMBLY AND ASSEMBLY
- Cautions to be observed when trouble shooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe
during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible
danger from a short circuit. You are asked to observe the following precautions carefully.
1. Always remove the power plug from the outlet before servicing.
2. Use an insulated screwdriver and wear rubber gloves when servicing the high voltage side.
3. Discharge the high voltage capacitor before touching any oven components or wiring.
(1) Check the grounding.
Do not operate on a two-wire extension cord.
The microwave oven is designed to be used while grounded.
It is imperative, therefore, to make sure it is grounded
properly before beginning repair work.
(2) Warning about the electric charge in the high voltage capacitor.
For about 30 seconds after the operation has stopped, electric
charge remains in the high voltage capacitor.
When replacing or checking parts, short between oven chassis
and the negative high terminal of the high voltage capacitor by
using a properly insulated screwdriver to discharge.
4. When the fuse is blown out due to the operation of the monitor
switch; replace primary interlock switch, secondary interlock switch
and interlock monitor switch.
5. After repair or replacement of parts, make sure that the screws are
properly tightened, and all electrical connections are tightened.
6. Do not operate without cabinet.
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, take care when touching or replacing high potential parts because of
electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron,
HV Capacitor, HV Diode.
9

1. To remove cabinet
1) Remove four screws on cabinet back.
2) Push the cabinet backward.
2. To remove door assembly
1) Remove two screws which secure the stopper hinge top.
2) Remove the door assembly from top plate of cavity.
3) Reverse the above for assemby.
NOTE: After replacing the door assembly, perform a check
of correct alignment with the hinge and cavity front
plate.
10

11
A10 A09 A08 A07
A06A05
A04
A03
A02
A01
A11
A12
A13
REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK
A01 3512603620 HANDLE DOOR S455C 1
A02 3511608300 DECORATOR DOOR*R SUS430 T0.5 H/L 1
A03 3512204820 FRAME DOOR ALLOY PC+ABS 1
A04 7001503011 SCREW MACHINE PAN 5*30 MFZN 2
A05 3515101800 SPRING HOOK PW1 1
A06 3513101200 HOOK POM 1
A07 3512302400 GASKET DOOR PBT 1
A08 3516602200 DOOR PLATE SBHG-3A T0.7 1
A09 3515304800 SUPPORTER HINGE*T SCP-1 T2.0 1
A10 3517007120 BARRIER-SCREEN *O GLASS T3.2 1
3517007130 BARRIER-SCREEN *O GLASS T3.2 MIRROR 1 KOC-9N4T7S24 ONLY
A11 3511608700 DECORATOR DOOR*T SUS430 T0.5 H/L 1
A12 3511608400 DECORATOR DOOR*L SUS430 T0.5 H/L 1
A13 3511608200 DECORATOR DOOR*U SUS430 T0.5 H/L 1
3. To remove door parts.
1) KOC-9N4T/9N5T
(1) Remove the gasket door from door plate.
(2) Remove the door frame from door plate.
(3) Remove screws from door frame.
(4) Remove the handle from door frame.
(5) Remove the decorator door from door frame.
(6) Remove the stopper hinge top from door plate.
(7) Remove the spring and the hook.
(8) Remove barrier screen outer from door frame.
(9) Reverse the above steps for reassembly.
✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list.
So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center

12
4. Method to reduce the gap between the door seal and the oven front surface.
(1) To reduce gap located on part ‘A’.
• Loosen two screws on stopper hinge top, and then push the door
to contact the door seal to oven front surface.
• Tighten two screws.
(2) To reduce gap located on part ‘B’.
• Loosen two screws on stopper hinge under, and then push the
door to contact the door seal to oven front surface.
• Tighten two screws.
NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm
2
.

13
2) KOC-9N5T7S,9N5T7R,9N5T7S21
REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK
B01 3513406330 KNOB VOLUME ABS SG-175 SG-0760D 1
B02 3515501820 WINDOW DISPLAY PMMA 1
B03 3511608110 DECORATOR C-PANEL SUS430 T0.5 H/L 1
B04 3516005600 SPECIAL DOUBLE TAPE HOSTIC 550M(D)TO.15 1
B05 3516725260 CONTROL-PANEL ABS XR-401 SG-0320G 1
B06 3516909080 BUTTON FUNCTION-A ABS SG-175 SG-0760D SPRAY 1
B07 71222401211 SCREW TAPPING T2S TRS 4*12 MFZN 4
PKMPMSA200 PCB MAIN AS KOC-9N4T7S 1 KOC-9N5T7S,
B08 9N5T7S21
PKMPMSA220 PCB MAIN AS KOC-9N5T7R 1 KOC-9N5T7R
B09 7121301011 SCREW TAPPING T2S PAN 3*10 MFZN 5
B10 PKBPMSA200 PCB SUB AS KOC-9N4T7S 1
B11 3516909090 BUTTON FUNCTION-B ABS SG-175 SG-0760D SPRAY 1
(1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly.
(2) Remove four screws(B07) which secure the PCB Main ASS’Y.
(3) Pull out the Main PCB assembly(B08).
(4) Remove four screws(B09) which secure the PCB Sub ASS’Y.
(5) Pull out the Sub PCB assembly(B10).
(6) Pull out the Knob volume(B01) from the Sub PCB assembly.
(7) Pull out ten buttons from the control panel.
(8) Pull out Decorator control panel(B03) from the control panel.
(9) Pull out Window display(B02) from the control panel.
(10)Reverse the above steps for reassembly.
✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list.
So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center

14
CAUTION : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to
prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave
leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
Magnetron
antenna
<MAGNETRON>
Metallic
gasket
plate
Cooling fin Filament
terminal
6. To remove high voltage capacitor.
1) Remove a screw which secure the grounding ring
terminal of the H.V. diode and the capacitor holder.
2) Remove the H.V. diode from the capacitor holder.
3) Reverse the above steps for reassembly.
High voltage circuit wiring
7. To remove magnetron.
1) Remove a screw which secure the magnetron.
2) Remove the magnetron.
3) Reverse the above steps for reassembly.

15
8. To remove wind guide assembly.
1) Remove a screw for earthing.
2) Remove the noise filter from the wind guide.
3) Remove a screw which secure the wind guide assembly.
4) Draw forward the wind guide assembly.
5) Pull the fan from the motor shaft.
6) Remove two screws which secure the motor shaded pole.
7) Remove the motor shaded pole.
8) Reverse the above steps for reasembly.
9. To remove H.V.transformer.
1) Remove four screws holding the H.V.transformer.
2) Remove the H.V.transformer.
3) Reverse the above steps for reassembly.

16
10. To remove Top heater assembly parts.
1) Remove a screw and pull out Guide air outlet .
2) Remove screws and pull out braket heater *T .
3) Pull out heater miraclon
4) Remove two screws .
5) Pull out the heater reflector from cover heater *T .
6) Reverse the above steps for reassembly.
REF NO. PART CODE PART NAME DESCRIPTION Q’TY REMARK
1 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 1
2 3512520500 GUIDE AIR OUTLET SA1D T0.5 1
3 3512804900 HEATER REFLECTOR STS430 T0.5 1
4 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 2
5 3510607700 BRACKET HEATER *T SA1D T0.5 2
6 3512805800 HEATER MIRACLON 230V 800W 270MM 1
7 3511410300 COVER HEATER *T SA1D T0.5 1
✔ Caution:In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center
12
6
.
7
3
9
4
8
5123467

17
11. To remove Rear heater assembly parts.
1) Remove a screw and pull out Cover motor *B .
2) Remove a screw and pull out Cover *B .
3) Pull out the Harness convection-B .
4) Remove four screws and then pull out the Rear heater assembly.
5) Remove a Nut and the pull out the Fan convection .
6) Remove three screws and then separate the Cover heater *B and the lnsulator heater *B .
7) Pull out the Heater from the Cover Heater *B .
8) Remove two screw and then separate the lnsulator heater *B and Motor shaded pole .
9) Remove the C-Ring and then pull out the Fan from Motor shaft.
10)Reverse the above steps for reassebly.
14 15 16 17
2345678910111213
1
REF NO. PART CODE PART NAME DESCRIPTION Q TY REMARK
2 3511407300 COVER MOTOR*B SA1D-80 T0.5 1
1 7112401011 SCREW TAPPING T1 TRS 4*10 MFZN 1
3 7112401011 SCREW TAPPING T1 TRS 4*10 MFZN 1
4 3511407900 COVER*B SA1D-80 T0.5 1
5 3512767611 HARNESS CONVECTION KOC-924T0S ALTERNATE 1
6 7113400814 SCREW TAPPING T1 BIN 4*8 MFNI 4
8 3511409800 COVER HEATER*B SA1D-80 T0.5 1
7 3513303400 INSULATOR HEATER*B SBHG-1 T0.5 1
9 7113400814 SCREW TAPPING T1 BIN 4*8 MFNI 3
10 3511800700 FAN CONVECTION SA1D-80 T0.5 1
11 3513002300 HOLDER HEATER SUS 304 T0.5 3
12 3512801800 HEATER 230V 1400W 1R18344 1
13 7400104011 WASHER PLAIN PW-1-4 MFZN 1
14 7601400811 SCREW MACHINE PAN 4*8 SW MFZN 2
15 3963514330 MOTOR SHADED POLE 230V 50Hz MW10CA-T03 1
16 3511800900 FAN PBT 1
17 7402704600 RING C CR-5 SK5 1
✔ Caution: In this Service Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List) in Service information Center
12
34
5
6
e0
978
w7
r8t
uy

18
7. INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when
the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
(1) Primary interlock switch
When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate.
When the door is closed, the hook pushes the button of the microswitch. Then the button of the primary interlock switch
bring it under ON condition.
(2) Secondary interlock switch and interlock monitor switch
When the door is closed, the hook pushes the lock lever downward. The lock lever presses the button of the interlock
monitor switch to bring it under OFF condition and presses the button of the secondary interlock switch to bring it under
ON condition.
(3) Adjustment steps
a) Loosen the one mounting screw.
b) Adjust interlock switch assembly position.
c) Make sure that lock lever moves smoothly after adjustment is completed.
d) Tighten completely two mounting screws.
ADJUSTMENT :
Interlock monitor switch
When the door is closed, the interlock monitor switch should be opened before other switches are closed.
When the door is opened, the interlock monitor switch should be closed after other switches are opened.
NOTE :
Microwave emission test should be performed after adjusting interlock mechanism.
If the microwave emission exceed 4mW/cm2, readjust interlock mechanism.

19
8. TROUBLE SHOOTING GUIDE
Following the procedure below to check if the oven is defective or not.
1) Check grounding before trouble checking.
2) Be careful of the high voltage circuit.
3) Discharge the high voltage capacitor.
4) When checking the continuity of the switches, fuse or high voltage tranformer, disconnect one load wire from these
parts and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to
your meter.
(TROUBLE 1) Oven does not operate at all : any inputs can not be accepted.
NOTE : When electric parts are checked, be sure the power cord is not inserted the wall outlet.
Check wire harness, wiring and connection of the terminals and power cord before check the parts listed below.
CONDITION CHECK
Check continuity of
interlock monitor switch with
door closed
( COM NC )
Check continuity of
both primary and secondary
interlock switch with door closed
Malfunction of
Interlock
monitor switch
Malfunction of
interlock switch
RESULT
Continuity
No continuity
CAUSE REMEDY
Replace
(COM NC)
Fuse blows.
Replace
Shorted contacts
of primary
interlock Switch
Continuity Replace
Check continuity of
primary interlock switch contact
with door partially open until
interlock monitor switch contact
close
( COM NC close )
Defective low
voltage
transformer
Defective
high voltage
transformer
or infinite Replace
Replace
Check continuity of
primary winding of low voltage
transformer
Disconnect high voltage
fuse and operate the unit
No
Continuity
Continuity
Approx.
480 ~620
( normal )
Fuse again
blows

20
CONDITION CHECK
Check continuity of
magnetron Defective
magnetron.
RESULT
No
continuity
CAUSE REMEDY
Replace
Outlet has
proper
voltage
fuse does not
blow? Check continuity of noise filter
board Defective line
filter board
No
continuity Replace
Check continuity of
power supply cord
Defective touch
control circuit Replace
Open power
supply cord
No
continuity
No
continuity
Replace
NOTE : All these switches must be replaced at the same time, please refer to (7.Interlock mechanism and
adjust) for adjustment instructions
(TROUBLE 2)
Display shows all figures selected, but oven does not start cooking, even though desired program and time
are set and start button is tapped.
CONDITION CHECK
Check continuity of
primary interlock switch Malfunction of
primary interlock
switch
RESULT
No
continuity
CAUSE REMEDY
Adjust or
replace
Turn table
motor and
oven lamp
do
not turn on
Check D.C voltage
being supplied to
RELAY(RY4) coil
Fault contacts
of RELAY
(RY4) or open
relay coil.
Replace
Check continuity of
secondary interlock
and D.O.M switch
Malfunction of
secondary
Interlock and
D.O.M switch
No
continuity Adjust or
replace
Defective touch
control Circuit
0V
Approx.
24V DC
Replace