Electrolux EWM1000 User manual

SERVICE MANUAL
WASHING
©ELECTROLUX ITALIA S.p.A.
Spares Operations Italy
Corso Lino Zanussi, 30
Publication no.
I - 33080 PORCIA /PN (ITALY) 599 72 40-80
Fax [phone]
Edition: 12-2009
EN
WM-WD
Front loader
Platform
EWM1000
EWM1000plus
EWM2000evo
EWM3000new
ENV06
11xx21xx
25xx/35xx

QUICK GUIDE AND APPLIANCES LIST 2/176 599 72 40-80

QUICK GUIDE AND APPLIANCES LIST 3/176 599 72 40-80
Content
1EWM1000 ............................................................................................................................................5
1.1 Access to the diagnostic cycle ....................................................................................................5
1.2 Rapid reading of alarms..............................................................................................................5
1.3 Cancelling the last alarm.............................................................................................................5
1.4 Phases of the diagnostics test.....................................................................................................6
1.5 Reading the alarms.....................................................................................................................7
1.5.1 Displaying the alarm..............................................................................................................7
1.5.2 Examples of alarm display.....................................................................................................7
1.5.3 Status of alarms during the diagnostics cycle.........................................................................7
1.6 Table of alarms codes EWM1000 ...............................................................................................8
1.6.1 Notes concerning certain alarm codes...................................................................................9
1.7 Elementary diagram..................................................................................................................10
1.7.1 With instantaneous door locking device...............................................................................10
1.8 With PTC door locking device...................................................................................................11
1.8.1 Key to circuit diagram..........................................................................................................12
1.9 Connectors on circuit board EWM1000.....................................................................................13
1.10 Burning on the circuit board EWM1000.....................................................................................14
1.10.1 EWM1000........................................................................................................................... 14
1.10.2 Components side (common)................................................................................................14
1.10.3 Pushbutton – led side (horizontal buttons)...........................................................................15
1.10.4 Pushbutton – led side (vertical buttons)...............................................................................15
2EWM1000plus 2000evo 3000new.....................................................................................................16
2.1 Control panel............................................................................................................................16
2.2 Sigma/Alpha/Ellipse//Multipanel Built-In/Sigma-ZK/Jewel with or without selector......................17
2.2.1 Access to diagnostics system..............................................................................................17
2.2.2 Rapid reading of alarm codes..............................................................................................17
2.2.3 Cancelling the last alarm..................................................................................................... 17
2.3 AEG NexXxt Version with selector and incorporated ON/OFF switch.........................................18
2.3.1 Access to diagnostics system..............................................................................................18
2.3.2 Rapid reading of alarm codes..............................................................................................18
2.3.3 Cancelling the last alarm..................................................................................................... 18
2.4 AEG New Version with right selector and incorporated ON/OFF switch.....................................19
2.4.1 Access to diagnostics system..............................................................................................19
2.4.2 Rapid reading of alarm codes..............................................................................................19
2.4.3 Cancelling the last alarm..................................................................................................... 19
2.5 DELTA Version without selector and button ON/OFF switch......................................................20
2.5.1 Access to diagnostics system..............................................................................................20
2.5.2 Rapid reading of alarm codes..............................................................................................20
2.5.3 Cancelling the last alarm..................................................................................................... 20
2.6 CLUB DISPLAY Version with selector and incorporated ON/OFF switch...................................21
2.6.1 Access to diagnostics system..............................................................................................21
2.6.2 Rapid reading of alarm codes..............................................................................................21
2.6.3 Cancelling the last alarm..................................................................................................... 21
2.7 LCD Version without selector and button ON/OFF switch..........................................................22
2.7.1 Access to diagnostics system..............................................................................................22
2.7.2 Rapid reading of alarm codes..............................................................................................22
2.7.3 Cancelling the last alarm..................................................................................................... 22
2.8 LCD Version with selector and button ON/OFF switch...............................................................23
2.8.1 Access to diagnostics system..............................................................................................23
2.8.2 Rapid reading of alarm codes..............................................................................................23
2.8.3 Cancelling the last alarm..................................................................................................... 23
2.9 Phases of the diagnostics test...................................................................................................24
2.10 Reading the alarm codes..........................................................................................................26
2.10.1 Displaying the alarm............................................................................................................26
2.10.2 Examples of alarm displays.................................................................................................26
2.11 Table of alarms codes EWM 1000plus EWM2000EVO EWM3000NEW.................................27
2.12 Basic circuit diagram EWM1000PLUS.......................................................................................31
2.12.1 Diagram (without aqua control)............................................................................................31
2.12.2 Key to circuit diagram..........................................................................................................32
2.12.3 Diagram (with aqua control).................................................................................................33
2.12.4 Key to circuit diagram..........................................................................................................34
2.13 Basic circuit diagram with sensor EWM2000EVO......................................................................35

QUICK GUIDE AND APPLIANCES LIST 4/176 599 72 40-80
2.13.1 Key for circuit diagram.........................................................................................................36
2.14 Basic circuit diagram with sensor EWM3000NEW.....................................................................37
2.14.1 Key for circuit diagram.........................................................................................................38
2.15 Connectors on circuit board EWM1000plus...............................................................................39
2.16 Burning on the circuit board EWM1000plus...............................................................................40
3ENV 06...............................................................................................................................................41
3.1 Access to the diagnostic cycle ..................................................................................................41
3.1.1 All version...........................................................................................................................41
3.1.2 INPUT version.....................................................................................................................41
3.1.3 Rapid reading of alarm codes..............................................................................................41
3.2 Cancelling the last alarm...........................................................................................................42
3.3 Phases of the diagnostic cycle..................................................................................................43
3.4 Alarm displaying.......................................................................................................................44
3.4.1 AEG Version:......................................................................................................................44
3.4.2 Other versions:....................................................................................................................44
3.4.3 Examples of alarm display...................................................................................................44
3.4.4 Operation of alarms during diagnostics................................................................................44
3.5 Table of alarms codes ENV06...................................................................................................44
3.5.1 Notes concerning certain alarm codes.................................................................................44
3.6 Basic circuit diagram EWM1100................................................................................................44
3.6.1 Key to circuit diagram EWM1100.........................................................................................44
3.7 Connectors on circuit board EWM1100.....................................................................................44
3.8 Burning on the circuit board EWM1100.....................................................................................44
3.9 Basic circuit diagram WM EWM2100 ........................................................................................44
3.9.1 Key to circuit diagram WM EWM2100..................................................................................44
3.10 Basic circuit diagram WM with aqua control EWM2100.............................................................44
3.10.1 Key to circuit diagram WM with Aqua Control EWM2100.....................................................44
3.11 Basic circuit diagram WD EWM2100.........................................................................................44
3.11.1 Key to circuit diagram WD EWM2100..................................................................................44
3.12 Basic circuit diagram WD with aqua control EWM2100..............................................................44
3.12.1 Key to circuit diagram WD with aqua control EWM2100.......................................................44
3.13 Connectors on circuit board WM/WD EWM2100.......................................................................44
3.14 Burning on the circuit board EWM2100 WM/WD.......................................................................44
3.15 Basic circuit diagram EWM25xx without aqua control................................................................44
3.15.1 Key to circuit diagram EWM25xx with Aqua Control.............................................................44
3.16 Basic circuit diagram EWM25xx without aqua control................................................................44
3.16.1 Key to circuit diagram EWM25xx without Aqua Control........................................................44
3.17 Basic circuit diagram EWM25xx WD without aqua control.........................................................44
3.17.1 Key to circuit diagram EWM25xx WD with Aqua Control......................................................44
3.18 Basic circuit diagram EWM25xx WD without aqua control.........................................................44
3.18.1 Key to circuit diagram EWM25xx WD without aqua control ..................................................44
3.19 Basic circuit diagram EWM35xx with aqua control.....................................................................44
3.19.1 Key to circuit diagram EWM35xx with Aqua Control.............................................................44
3.20 Basic circuit diagram EWM35xx without aqua control................................................................44
3.20.1 Key to circuit diagram EWM35xx without Aqua Control........................................................44
3.21 Connectors on circuit board WM/WD EWM25xx/35xx ...............................................................44
3.22 Burning on the circuit boards EWM25xx/35xx WM/WD..............................................................44
3.23 Burning on the circuit board WD................................................................................................44
4Appliances list ....................................................................................................................................44

EWM1000
1 EWM1000
1.1 Access to the diagnostic cycle
version with horizontal pushbuttons version with vertical pushbuttons
1. Switch off the appliance.
2. Press and hold down the START/PAUSE button and any one of the OPTION buttons simultaneously.
horizontal version, while for vertical version pushbuttons are 2and 3.
3. Holding down both buttons, switch the appliance on by turning the programme selector one position
clockwise.
4. Continue to hold down the START/PAUSE button and the OPTION button horizontal version, while for
vertical version pushbuttons are 2and 3, until the LEDs begin to flash (at least 2 seconds).
5. To exit the diagnostics system switch the appliance off, on and then off again.
IMPORTANT: The position of the START/PAUSE button varies according to the model, and is
therefore not always the same.
1.2 Rapid reading of alarms
The last alarm can be displayed even if the programme selector is not in the tenth position (diagnostics) or if
the appliance is in normal operating mode (e.g. while the washing programme is in operation):
version with horizontal pushbuttons version with vertical pushbuttons
1. Press START/PAUSE and any one of the option buttons simultaneously for horizontal version, while
for vertical version pushbuttons are 2and 3, for at least two seconds: the LEDs first switch off, and then
display the flashing sequence corresponding to the alarm condition.
2. The alarm sequence continues as long as the two buttons are held down.
3. While the alarms are displayed, the current cycle being performed continues or, if the appliance is in the
programme selection phase, the options previously selected remain in memory.
1.3 Cancelling the last alarm
version with horizontal pushbuttons version with vertical pushbuttons
1. Access alarm reading mode (tenth selector position)
2. Press and hold down START/PAUSE and any one of the option keys simultaneously for horizontal
version, while for vertical version pushbuttons are 2and 3.
3. Hold the START/PAUSE and OPTION button down until the LEDs begin to flash (about 5 seconds)

EWM1000
QUICK GUIDE AND APPLIANCES LIST 6/176 599 72 40-80
1.4 Phases of the diagnostics test
After accessing the diagnostics cycle, and irrespective of the type of control board fitted to the appliance
(i.e. vertical or horizontal buttons) and the configuration of the selector, turn the programme selector
clockwise to perform the diagnostics cycle for the various components and to read the alarms.
All the alarms are enabled during the diagnostics cycle.
Position of
selector Components activated Conditions of operation Function tested
1
-All the LEDs light in sequence
-When a button is pressed, the
corresponding LED lights (and
the buzzer may sound)
Always enabled Operation of the
user interface
2
-Door safety interlock
-Washing solenoid valve
Door locked
Water level lower than anti-
overflow level
Maximum time 5 minutes
Water ducted
through washing
compartment
3
-Door safety interlock
-Pre-wash solenoid valve
Door locked
Water level lower than anti-
overflow level
Maximum time 5 minutes
Water ducted
through pre-wash
(bleach)
compartment
4
-Door safety interlock
-Washing and pre-wash solenoid
valves
Door locked
Water level lower than anti-
overflow level
Maximum time 5 minutes
Water ducted
through conditioner
compartment
6
-Door safety interlock
-Wash solenoid (if the water in
the tub is below 1st level)
-Heating element
Door locked
Water level > 1st level
Maximum time 10 minutes or
up to 90°C (*) Heating
7
-Door safety interlock
-Wash solenoid (if the water in
the tub is below 1st level)
-Motor (55 rpm clockwise, 55
rpm anti-clockwise, impulse at
250 rpm)
Door locked
Water level > 1st level Check for leaks from the tub
8
-Door safety interlock
-Drain pump
-Motor up to 650 rpm then at
maximum spin speed
Door locked
Water level lower then anti-
boiling level for spinning
Drain and spin,
check for
congruence in
closure of pressure
switch levels
9
Only for top-loaders with drum
positioning system:
-Door safety interlock
-Motor (25 rpm)
-Drain pump
Door locked
Water level lower then anti-
boiling level
Maximum time 2 minutes
Test for positioning
of drum
(*) In most cases, this time is sufficient to check the heating function. However, the time can be increased by repeating the heating
phase without draining the water: pass for a moment to a different phase of the diagnostics cycle and then back to the heating
check phase (if the temperature is higher than 80°C, heating does not take place).

EWM1000
QUICK GUIDE AND APPLIANCES LIST 7/176 599 72 40-80
1.5 Reading the alarms
Proceed as follows to read the last alarm condition stored in the EEPROM on the
control board:
•Access diagnostics mode.
•Irrespective of the type of control board and configuration, turn the programme
selector clockwise to the tenth position.
1.5.1 Displaying the alarm
The alarm is displayed by a repeated flashing sequence of the two LEDs (0.4
seconds ON, 0.4 seconds OFF, with a pause of 2.5 seconds between each
sequence). The buzzer (if featured) sounds a series of “beeps” in synchronization
with the flashing of the LEDs.
•END OF CYCLE indicator →indicates the first digit of the alarm code (family)
•START/PAUSE →indicates the second digit of the alarm code (number
within the family).
These two LEDs are present on all models (though configured in different
positions) and flash simultaneously.
Notes:
•The first letter of the alarm code “E” (Error) is not displayed since it is the same for all alarm codes.
•The alarm code families are expressed in hexadecimal form. In other words:
→A is represented by 10 flashes
→B is represented by 11 flashes
→...
→F is represented by 15 flashes
•Configuration errors are displayed by the flashing of all the LEDs (user interface not configured).
1.5.2 Examples of alarm display
Example: Alarm E43 (problems with the door safety interlock triac) will be displayed as follows:
•four flashes of the END OF CYCLE LED indicate the first digit E43;
•three flashes of the START/PAUSE LED indicate the second digit E43;
END OF CYCLE LED START/PAUSE LED
ON/OFF Time
(seconds) Value ON/OFF Time
(seconds) Value
0.4 0.4
0.4 1 0.4 1
0.4 0.4
0.4 2 0.4 2
0.4 0.4
0.4 3 0.4 3
0.4
0.4 4
2.5 Pause 3,3 Pause
1.5.3 Status of alarms during the diagnostics cycle
All the alarms are enabled during the components diagnostics test.

EWM1000
QUICK GUIDE AND APPLIANCES LIST 8/176 599 72 40-80
1.6 Table of alarms codes EWM1000
Alarm Description Possible fault Action/Machine status Reset
E00 No alarm
E11 Difficulty in filling during wash phase
Tap closed or water pressure insufficient; Drain hose
incorrectly positioned; Water fill solenoid faulty; Leaks from
pressure switch hydraulic circuit; Pressure switch faulty;
Wiring faulty; Circuit board faulty.
Cycle paused, door closed Start
E13 Water leakage
Drain hose incorrectly positioned; Water pressure
insufficient; Water fill solenoid faulty; Leaks or blockage in
pressure switch hydraulic circuit; Pressure switch faulty;
Circuit board faulty. Cycle paused, door closed Start
E21 Difficulties in draining
Drain hose kinked/blocked/incorrectly positioned; Drain filter
clogged or dirty; Drain pump faulty; Pressure switch faulty;
Wiring faulty; Circuit board faulty; Current leakage from
heating element to ground. Cycle paused Start
E23 Drain pump triac faulty Drain pump faulty; Wiring faulty; Circuit board faulty. Safety drain - Cycle stopped, door open Selector on “0”
E24 Problems with «sensing» of drain pump triac Circuit board faulty. Safety drain – Cycle stopped, door released Selector on “0”
E33 Incongruence between contact closure of anti-
boiling and 1st level of pressure switch
Pressure switch faulty; Current leakage from heating
element to ground; Heating element; Wiring faulty; Circuit
board faulty. Safety drain - Cycle stopped, door open Selector on “0”
E35 Water overflow Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit
board faulty.
Cycle blocked, door closed. Safety drain.
Drain pump (sequence 5 min. ON - 5 min.
OFF) Selector on “0”
E36 «sensing» circuit of anti-boiling pressure switch
faulty Circuit board faulty. Cycle blocked, door closed Selector on “0”
E37 «sensing» circuit of 1st level faulty Circuit board faulty. Cycle blocked, door closed Selector on “0”
E39 HV «sensing» circuit of anti-flooding pressure
switch faulty Circuit board faulty. Cycle blocked, door closed Selector on “0”
E41 Door open Door safety interlock faulty; Wiring faulty;
Circuit board faulty. Cycle paused Start
E42 Problems with aperture of door Door safety interlock faulty; Wiring faulty;
Circuit board faulty Cycle paused Start or Selector
on “0”
E43 Power triac on door interlock faulty Door safety interlock faulty; Wiring faulty;
Circuit board faulty. Safety drain, door released Selector on “0”
E44 Door interlock «sensing» faulty Circuit board faulty. Safety drain, door released Selector on “0”
E45 «sensing» on door interlock triac faulty Circuit board faulty. Safety drain, door released Selector on “0”
E51 Motor power triac short-circuited Circuit board faulty;
Current leakage from motor or wiring. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection) Selector on “0”
E52 No signal from motor tachimetric generator Motor faulty; Wiring faulty;
Circuit board faulty. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection) Selector on “0”
E53 «sensing» circuit on motor triac faulty Circuit board faulty. Cycle blocked Selector on “0”

EWM1000
QUICK GUIDE AND APPLIANCES LIST 9/176 599 72 40-80
Alarm Description Possible fault Action/Machine status Reset
E54 Motor relay contacts sticking Circuit board faulty;
Current leakage from motor or wiring. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection) Selector on “0”
E61 Insufficient heating during washing NTC sensor faulty; Heating element faulty; Wiring faulty;
Circuit board faulty. Heating phase skipped ---
E62 Overheating during washing NTC sensor faulty; Heating element faulty; Wiring faulty;
Circuit board faulty. Safety drain (with cooling water fill) - Stop with door open Selector on “0”
E66 Power relay for heating element faulty Circuit board faulty; Current leakage from heating element
or wiring to ground. Safety drain (with cooling water fill) - Stop with door open Selector on “0”
E71 NTC washing sensor faulty NTC sensor faulty; Wiring faulty;
Circuit board faulty. Heating phase skipped ---
E82 Error in reset position of selector Circuit board faulty. Cycle cancelled Selector on “0”
E83 Error in reading selector position Configuration data incorrect; Circuit board faulty. During the cycle continues normally, switches
off completely during selection ---
E93 Incorrect machine configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0”
E94 Incorrect washing cycle configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0”
E95 Communications error between microprocessor
and EEPROM Circuit board faulty. Appliance blocked Selector on “0”
E96 Incongruence between hardware version and
configuration. Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0”
E97 Incongruence between programme selector and
cycle configuration Configuration data incorrect; Circuit board faulty. Appliance blocked Selector on “0”
EB1 Power supply frequency of appliance incorrect Mains power supply problems (incorrect / interference);
Circuit board faulty. Cycle blocked until normal power supply conditions are restored Selector on “0”
EB2 Voltage too high Mains power supply problems (incorrect / interference);
Circuit board faulty. Cycle blocked until normal power supply conditions are restored Selector on “0”
EB3 Voltage too low Mains power supply problems (incorrect / interference);
Circuit board faulty. Cycle blocked until normal power supply conditions are restored Selector on “0”
1.6.1 Notes concerning certain alarm codes
Configuration alarms E93-E96: If these alarms are generated (when the appliance is switched on), operation of the appliance is blocked and all the
LEDs light. The diagnostics procedure cannot be accessed; the only option is to switch the appliance OFF (by turning the selector to position “0”).
Configuration alarm E94: For this alarm code, only the family for alarm “9” is displayed; the diagnostics procedure cannot be accessed, and the “rapid
alarm display” function cannot be used.
Alarms EB1-EB2-EB3: In the event of problems with the mains power supply, the appliance remains in alarm mode until the mains frequency or
voltage are restored to the correct value or the appliance is switched off (by turning the programme selector to “0”). The family of alarm “B” is displayed;
the diagnostics procedure cannot be accessed, and the “rapid alarm display” function cannot be used. The complete alarm code can be read only when
the abnormal situation has ceased.
Alarms E51- E52: During the diagnostics test, all the alarms are displayed. Normally, when the programme selector is turned from one test phase to
another, the appliance exits the alarm condition and performs the phase selected. This does not take place in the case of alarms E51 (power triac on
motor short-circuited) and E52 (no signal from the tachymetric generator on the motor): in these cases, the only option to exit the alarm condition is to
switch the appliance OFF by turning the selector to position “0” (reset).

EWM1000
QUICK GUIDE AND APPLIANCES LIST 10/176 599 72 40-80
1.7 Elementary diagram
1.7.1 With instantaneous door locking device

EWM1000
QUICK GUIDE AND APPLIANCES LIST 11/176 599 72 40-80
1.8 With PTC door locking device

EWM1000
QUICK GUIDE AND APPLIANCES LIST 12/176 599 72 40-80
1.8.1 Key to circuit diagram
Electrical components – appliance Components of electronic circuit board
1. Circuit board
2. Suppressor
3. Main switch (on programme selector)
4. Door safety interlock
5. 1st level pressure switch
6. Anti-boiling pressure switch
7. Anti-overflow pressure switch (certain models only)
8. Heating element
9. Stator (motor)
10. Overload circuit-breaker (motor)
11. Tachymetric generator (motor)
12. Rotor (motor)
13. Drain pump
14. Pre-wash solenoid valve
15. Washing solenoid valve
16. “Door closed” lamp (certain models only)
17. Drum positioning system (DSP) (top-loaders – certain models only)
DOOR_TY Triac for door safety interlock
DRAIN_TY Triac for drain pump
K1 Heating element relay
K2 Motor relay: clockwise rotation
K3 Motor relay: anti-clockwise rotation
K4 Motor relay: half-range power (certain models only)
MOTOR_TY Motor triac
ON/OFF Main switch (programme selector)
PWELW_TY Triac for pre-wash solenoid valve
Serial interface Asynchronous serial interface
WELV_TY Triac for washing solenoid valve

EWM1000
QUICK GUIDE AND APPLIANCES LIST 13/176 599 72 40-80
1.9 Connectors on circuit board EWM1000
J6 J2 J1 J3 J4 J5 J7
J6-1: Heating element
(relay)
J6-2: Door safety
interlock (line)
J8
J8-1 line
J8-2 line (neutral)
J2-1 Door safety interlock
(line-sensing)
J2-2 1st level(sensing)
J2-3 (Anti-overflow
pressure switch)
J2-4 Door safety interlock
(triac)
J2-5 (Door safety
interlock)
J2-6 (Anti-overflow
pressure switch)
J1-1 Motor (triac)
J1-2 Motor (stator – full
range)
J1-3 Motor (stator - 1/2
range)
J1-4 Motor (rotor)
J1-5 Motor (rotor)
J3-1 Drain pump (line)
J3-2 Solenoids (line)
J3-3 (line)
J3-4 Drain pump (triac)
J3-5 Pre-wash solenoid
(triac)
J3-6 Washing solenoid
(triac)
J3-7 Solenoids (line)
J3-8 (Not used)
J4-1 “Door closed” pilot
lamp
J4-2 “Door closed” pilot
lamp
J5-1 NTC temperature
sensor
J5-2 NTC temperature
sensor
J5-3 Motor (tachymetric
generator)
J5-4 Motor (tachymetric
generator)
J5-5 (DSP drum
positioning system)
Serial interface:
J7-1 ASY_IN
J7-2 ASY_OUT
J7-3 5V
J7-4 GND
Rear view
Front view

EWM1000
QUICK GUIDE AND APPLIANCES LIST 14/176 599 72 40-80
1.10 Burning on the circuit board EWM1000
1.10.1 EWM1000
In case of burning on the main circuit board, check that the problem is not caused by another electrical component (short-circuits, poor insulation, water leakage).
Refer to the figures below in order to identify the component that might have caused the burning according to the position of the burned area.
The circuit board shown below is the version with the greatest number of components: other boards may not feature all these components (relay K4 and buzzer).
1.10.2 Components side (common)
1. NTC washing temperature sensor
2. Drain pump
3. Power supply
4. Motor
5. Heating element
6. Door safety interlock
7. Water fill solenoids
8. Tachymetric generator (motor)
9. Drum positioning system (top-loaders)

EWM1000
QUICK GUIDE AND APPLIANCES LIST 15/176 599 72 40-80
1.10.3 Pushbutton – led side (horizontal buttons)
1.10.4 Pushbutton – led side (vertical buttons)
1. ---
2. Drain pump
3. Power supply
4. Motor
5. Heating element
6. Door safety interlock
7. Water fill solenoids
8. Tachymetric generator (motor)
9. Drum positioning system (top-loaders)

EWM1000plus EWM2000evo EWM3000new
QUICK GUIDE AND APPLIANCES LIST 16/176 599 72 40-80
2 EWM1000plus 2000evo 3000new
2.1 Control panel
The configuration of the control panel depends on the following:
ªType of control/display board (with or without display)
ªDesign of the control panel and position of the programme selector (right or left of the buttons)
ªNumber and configuration of the buttons (max. 8)
ªON/OFF switch: incorporated in the programme selector or with separated button
Version with left selector and incorporated ON/OFF button
Alpha-Rim Sigma
Club Display
Delta
Version with left selector and button ON/OFF switch
Alpha Ellipse
Version with right selector and button ON/OFF switch
Multipanel Built-in
Version with right selector and incorporated ON/OFF switch
Sigma/ZK AEG NexXxt AEG NEW
Club Display
Delta Version without selector and button ON/OFF switch
LCD Version without selector and button ON/OFF switch
LCD Version with left selector and incorporated ON/OFF button

EWM1000plus EWM2000evo EWM3000new
QUICK GUIDE AND APPLIANCES LIST 17/176 599 72 40-80
2.2 Sigma/Alpha/Ellipse//Multipanel Built-In/Sigma-ZK/Jewel with or without
selector
2.2.1 Access to diagnostics system
Attention: the programme selector is not always in the position indicated in the picture; it can be on the right
or on the left of the display board!
Version with selector and button ON/OFF switch
1. Cancel the set programme and switch the appliance off.
2. Rotate the programme selector of one positions clockwise.
3. Press the start/pause (8) button and any of the option button simultaneously and then, keeping them
pressed, switch the appliance on through the ON/OFF button (on/off).
4. Hold the start/pause and option buttons down till the LEDs start flashing (about 5 seconds).
5. To exit the diagnostics system switch the appliance off, on and then off again.
Version with selector and incorporated ON/OFF switch
1. Cancel the set programme switching the appliance off.
2. Press the start/pause (8) button and any of the option buttons simultaneously and then, keeping them
pressed, switch the appliance on rotating the programme selector of one position clockwise.
3. Hold the start/pause and option buttons down till the LEDs start flashing (about 5 seconds).
4. To exit the diagnostics system switch the appliance off, on and then off again.
2.2.2 Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
ªPress and hold down START/PAUSE and the option button nearest to the START/PAUSE button for at
least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to
the alarm; if the display is featured, it will display the alarm code
ªThe alarm sequence is displayed for the time in which the buttons are hold down
ªDuring the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps in memory the options previously chosen.
2.2.3 Cancelling the last alarm
It is good practice to cancel the last alarm, after reading the alarm code to check whether the alarm re-occurs
during the diagnostics control after the reparation of the appliance.
1. Select diagnostics mode and turn the programme selector to the tenth position (reading of alarm)
2. Press and hold down START/PAUSE and any of the option buttons at the same time for five
seconds.

EWM1000plus EWM2000evo EWM3000new
QUICK GUIDE AND APPLIANCES LIST 18/176 599 72 40-80
2.3 AEG NexXxt Version with selector and incorporated ON/OFF switch
2.3.1 Access to diagnostics system
1. Cancel the set programme and switch the appliance off.
2. Press buttons 1and 5(or button 2and 6) simultaneously and then, holding them down, switch
the appliance on by rotating the programme selector of one position clockwise.
3. To exit the diagnostics system switch the appliance off, on and then off again.
2.3.2 Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
ªPress buttons 1and 5 simultaneously for at least 2 seconds: the LED switch off and then display the
sequence of flashes indicating the alarm.
ªThe alarm sequence is displayed for the time in which the buttons are hold down
ªDuring the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps in memory the options previously chosen.
2.3.3 Cancelling the last alarm
It is good practice to cancel the last alarm, after reading the alarm code to check whether the alarm re-
occurs during the diagnostics control after the reparation of the appliance
1. Select diagnostics mode and turn the programme selector to the tenth position (reading of
alarm)
2. Press buttons 1and 5 simultaneously.
3. Hold buttons 1and 5down (about 2 seconds).

EWM1000plus EWM2000evo EWM3000new
QUICK GUIDE AND APPLIANCES LIST 19/176 599 72 40-80
2.4 AEG New Version with right selector and incorporated ON/OFF switch
2.4.1 Access to diagnostics system
1. Cancel the set programme and switch the appliance off.
2. Press buttons 1and 2simultaneously and then, holding them down, switch the appliance on
by rotating the programme selector of one position clockwise.
3. To exit the diagnostics system switch the appliance off, on and then off again.
2.4.2 Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
ªPress buttons 1and 2simultaneously for at least 2 seconds: the LED switch off and then display the
sequence of flashes indicating the alarm.
ªThe alarm sequence is displayed for the time in which the buttons are hold down
ªDuring the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps in memory the options previously chosen.
2.4.3 Cancelling the last alarm
It is good practice to cancel the last alarm, after reading the alarm code to check whether the alarm re-
occurs during the diagnostics control after the reparation of the appliance
1. Select diagnostics mode and turn the programme selector to the tenth position (reading of
alarm)
2. Press buttons 1and 2 simultaneously.
3. Hold buttons 1and 2down (about 2 seconds).

EWM1000plus EWM2000evo EWM3000new
QUICK GUIDE AND APPLIANCES LIST 20/176 599 72 40-80
2.5 DELTA Version without selector and button ON/OFF switch
2.5.1 Access to diagnostics system
1. Reset the set programme with the SKIP/RESET button and then switch the appliance off.
2. Press the START/PAUSE and SKIP/RESET buttons simultaneously and then, holding the
buttons down, switch the appliance on using the ON/OFF button.
3. Hold the buttons down until the buzzer sounds and the LEDs start flashing (about 4 seconds).
4. To exit the diagnostics system switch the appliance off, on and then off again.
2.5.2 Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
ªPress START/PAUSE and SKIP/RESET buttons simultaneously for at least 2 seconds: the LEDs switch
off and then display the sequence of flashes indicating the alarm.
ªThe alarm sequence is displayed for the time in which the buttons are hold down
ªDuring the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps the options previously chosen in memory.
2.5.3 Cancelling the last alarm
It is good practice to cancel the last alarm, after reading the alarm code to check whether the alarm re-
occurs during the diagnostics control after the reparation of the appliance
1. Select diagnostics mode and Press the Fabrics (1) or Temperature (2) button until LED L10
lights (reading of alarm).
2. Press and hold down START/PAUSE and START/RESET.