Electrolux FOM 71 CLS User manual

Installation manual
Wascator FOM71 CLS
438 9200-41/EN
07.45

3
Contents
Contents
Technical data........................................................................................... 1:1
Installation................................................................................................. 2:1
Transportation and unpacking..............................................................2:1
Siting and floor ..................................................................................... 3:1
Mechanical installation ......................................................................... 4:1
Water connections ............................................................................... 5:1
Drain connection .................................................................................. 6:1
Sample cock......................................................................................... 6:1
Connection of external liquid supplies.................................................. 7:1
Electrical installation............................................................................. 8:1
Function checks, Clarus Control............................................................... 9:1
Assembling the ruler ...............................................................................10:1
Calibration of level control system .......................................................... 11:1
Calibration of the scale (weight function)................................................ 12:1
Connection of thermosensor................................................................... 13:1
The manufacturer reserves the right to make changes in design
and materials specifications.
Safety
This machine can only be used with water. Never use dry cleaning
agents.
Do not allow children to operate the machine.
Do not hose down or spray the machine with water.
All mechanical and electrical installation must be carried out by
qualified personnel.
Do not bypass the door locking device.
Should the machine malfunction, please report the fault to the
technician responsible for the machine.

1:1
438 9160-01/03
Wascator FOM71 CLS
61
520
5.4
350
195
Wascator FOM71 CLS
DN20
3/4"
200-600
50-1000
20
50/75
170
Water valves
connection
BSP
Rec. water pressure
kPa
Functioning limits
for water valve
kPa
Capacity
at 300 kPa
l/min
Drain valve
outer Ø mm
Draining capacity
l/min
Connections
Technical data
Technical data
Innerdrum
volume litres
diameter mm
Heating
electricity kW
G-factor max
Weight, net kg

1:2
438 9160-01/02
Wascator FOM71 CLS
Function/subsystem
Ambient conditions
The machine shall be able to
function during the same ambient
conditions as normal washing
machines. However the functional
values with tolerances will only be
valid if following ambient condi-
tions are kept.
Voltage
Frequency
Water hardness
Inlet water Cold
Hot
Water pressure
Ambient temperature
Inner drum
Diameter
Depth
Volume
Lifting vanes: Number
Height
Radius
Base width
Perforation: Diameter
Depth of countersink
Total hole area
Material: Stainless steel
Outer drum
Diameter
Sump
Material: Stainless steel
Door opening
Opening diameter
Cabinet
Stainless steel
Nominal ±2%
Nominal ±2%
(2.5±0.2) mmol/l
(15±2) oC
Max (60±2)oC
(240±50) kPa
(20±5) oC
(520±1) mm
(315±1) mm
61 l
3
53 mm
17 mm
65 mm
5 mm
2.5 mm
600 mm2
2333 (SS 18/8)
554 mm
~ (1300±25) ml
2333 (SS 18/8)
310 mm
2333 (SS 18/8)
Technical data

1:3
438 9160-01/02
Wascator FOM71 CLS
Drum speed
Washing speed: Programmable
Extraction: Programmable
Reversing rhythm
Programmable
Water level
Weight sensing
Repeatability
Stepsize
Dosing accuracy weight
control
Level sending:
Repeatability
Stepsize
Dosing accuracy level
control
Thermostat
Continuos variable in each
wash sequence
Selectable interval
Programming steps
Switch off temperature accuracy
in Interval 30-97 oC
Interval switch off temperature –
switch on temperature
(20 – 59±1) RPM
(200 – 1100±20) RPM
(0 – 250±0.1) = sec.
(Tolerance area
refers to timer
intervals)
±0.1kg/bath
≤0.05kg
≤0.2kg/bath
±5 mm
≤2 mm
≤0.8litre/bath
Yes
(4-97) oC
1 oC
±1 oC
≤4 oC
Technical data

1:4
438 9160-01/02
Wascator FOM71 CLS
Soap box
Number of compartments
Number of programmable liquid
detergents
Wash programs
Memory cards for
Approvals
The machine shall have same
approvals as normal washing
machines
Special equipment
Manual cook for sampling of bath
water on right side:
Connection for temperature
recording sensor in rear gable:
Possibility to connect lint trap:
Memory card with copy safe
programs for M&S and (IEC; ISO):
Procedure for calibration of the
machine according to ISO 9000 rules:
Possibility to take out test pieces from
wash bath during the wash:
Analog output from load cells to data
acquisition systems:
4
4
IEC 60456
ISO 6330
M&S
CE
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Technical data

1:5
438 9160-01/02
Pre- programmed wash programs
The Clarus Control in the Wascator FOM71 CLS contains 9 pre-
programmed ”wash programs”. They are not real wash programs but are
mainly designated for checking purposes. The stored programs are:
Place Name Content
Technical data
991 Start-up program If the machine has been idle more than
two hours, this program should be run
before any other program is run.
992 Level check Check with ruler insider
Program fills machine with water to a
reference level at 160 mm, maintains
this level 20 seconds and press PAUS
and it empties the machine. This
process is repeated five times. After
that, the program fills machine with
water to the following levels one after
the other: 100 mm, 130 mm, 160 mm
and 200 mm. Each level is maintained
40 seconds before emptying.
993 Weight check Program fills the machine with water to
18 kg, wait 30 seconds, rotates 60
seconds and fills to 26 kg (+8) and waits
30 seconds. Then drain.
994 Temperature check Program fills machine with water to
130 mm level and warms it in five steps:
25°C for 2 minutes, 40°C for 2 minutes,
60°C for 2 minutes, 80°C for 2 minutes
and 90°C for 2 minutes. The machine is
emptied, filled twice with cold water to a
high level 200 mm and finishes with a
two minute spin cycle 1000 rpm. The
buzzer sounds at the end of the
program.
995 Extraction 500 RPM 1 min.
996 Extraction 500 RPM 5 min.
997 Extraction 775 RPM 2 min.
998 Extraction 950 RPM 4 min.
999 Extraction 1100 RPM 5 min.

1:6
438 9160-01/02
ABC D E F G H I K L M N O PR
720 690 1315 200 750 555 720 1230 220 1010 135 825 45 100 240 135
Wascator
FOM71 CLS
5716
P
5717
N
I
L
M
O
KH
R
1
32
5
4
B
G
A
FE
C
D
8
76
5715
Technical data
1Electrical connection
2Cold water
3Hot water
4Drain
5Liquid detergent supply
6Control panel
7Soap box
8Door opening, ø 310
Rear side
Right side
Front

2:1
438 9160-21/03
5711
2
3
5710
1
Installation
Transportation and unpacking
The machine is delivered bolted onto the
transport pallet and packed in a crate or box.
•Remove packing from the machine.
•Remove front and rear foundation panels.
Remove the bolts between the machine and
pallet.
•Mount front and rear panel.
•Mount the feet and spacers in the load cells.
Don´t move the machine until the feet have
been mounted.
Note the threaded holes for the feet.
• Push the machine back and mount the two
rear feet and then the two front feet.
The feet shall be mounted in the holes on the
load sensor bridge.
•Lift the machine and remove the transport
pallet.
•Place the machine on its final position.
•Level the machine with the feet of the
machine.
The machine also comes with transport safety
devices (four plate angles between the support
and the drum).
Fig.
2
Fig.
3
Fig.
1

2:2
438 9160-21/03
5712
4
Installation
In order to remove the safety devices:
•Remove front and rear panel.
•Remove both front metal angels.
•Remove both rear metal angels.
• The machine may not be moved with the
transport securities removed. Save the
transport securities for future use.
Fig.
4

3:1
438 9160-41/01
5710 A
1
50 mm
500 mm
Siting and floor
Install the machine close to a floor drain or open
drain.
In order to make installation and servicing the
machine easier the following clearances are
recommended:
•At least 500 mm between the machine and the
wall behind
•and min. 50 mm on both sides of the machine
whether installed next to the wall or other
machines.
Installation
Fig.
1

4:1
438 9160-61/01
5744 A
1
4
3
2
5745
5746 A
5747 + 5748
BB
FRONT
FRONT
34 650
718
661
36 117 659
ø 8
AA
A
FRONT
A
B
x 4
4
ø 8
40
Mechanical installation
•Mark the site of the machine installation.
•The round mark up (A) on the drawing are the
site for the feet of the machine.
•Two tilt protections shall be mounted for the
two feet at the front of the machine.
•Mark the four holes (B) on the floor.
•Drill ø8 to a depth of 40 mm. Mount the four
expander bolts in the holes.
•Lift the machine in the bottom frame and place
it with the feet in the cups. Center the feet in
cups as much as possible.
•Mount the tilt protection and tighten with two
screws.
•Check that the machine is placed in level.
Adjust with the feet, the lock with the counter
nuts.
It is of utmost importance that the machine
is placed in level, from side to side as well
as front to rear. If the machine is not
properly leveled, it may result in out-of-
balance without a real out of balance in the
drum.
Installation
Fig.
1
Fig.
2
Fig.
3
Fig.
4

5:1
438 9160-81/02
Installation
Water connections
All intake connections to the machine are to be fitted with manual shut-off
valves and filters, to facilitate installation and servicing. In certain cases
non-return valves will need to be fitted before the machine to comply with
local plumbing regulations.
Water pipes and hoses should be flushed clean before installation. After
installation hoses should hang in gentle arcs.
All water connectors must be connected up, otherwise the wash
program will not function correctly.
Mount the supplied water hoses or the Y-hose to the machine. Make sure
the hose(-s) hang in gentle arcs. A stiff hose may cause error in the
weighing system.

5:2
438 9160-81/02
1
5328
1
2
Installation
Water type Water connection
123
cold and cold hot
hot
Fig.
1

6:1
438 9161-01/02
5713
1
5709
2
Drain connection
Connect a 75 mm (2 1/2") flexible rubber hose to
the machine’s drain pipe, ensuring a downward
flow from the machine. Avoid sharp bends which
may prevent proper draining.
There shall be an air-gap of 50 mm between the
drain hose and the drain.
Be sure that the drain hose is flexible enough not
causing weight problems for the scale.
PVC-pipe or corresponding material may not be
connected to the machine due to the load cells.
The drainage hose should be located over a floor
drain, drainage channel or the like so that the
distance between the outlet and the drain is at
least 25 mm (1").
Sample cock
Mount the cock on the right hand side of the
machine. When mounting use thread tape.
Installation
Fig.
1
Fig.
2