Electrolux W365H User manual

Installation manual
W365H, W375H, W3105H,
W3130H, W3180H, W3240H, W3300H
Exacta & Clarus Control
438 9200-01
06.34

3
Contents
Contents
Technical data........................................................................................... 1:1
Installation................................................................................................. 2:1
Transportation and unpacking..............................................................2:1
Siting and floor ..................................................................................... 3:1
Mechanical installation ......................................................................... 4:1
Water connections ............................................................................... 5:1
Drain connection .................................................................................. 6:1
Steam connection ................................................................................ 7:1
Connection of external liquid supplies..................................................8:1
Electrical installation............................................................................. 9:1
Function checks ...................................................................................... 10:1
The manufacturer reserves the right to make changes in design
and materials specifications.
Safety
This machine can only be used with water. Never use dry cleaning
agents.
Do not allow children to operate the machine.
Do not hose down or spray the machine with water.
All mechanical and electrical installation must be carried out by
qualified personnel.
Do not bypass the door locking device.
Should the machine malfunction, please report the fault to the
technician responsible for the machine.

1:1
438 9142-41/04
W365H W375H W3105H W3130H W3180H W3240H W3300H
65 75 105 130 180 240 300
520 520 595 650 725 795 795
52 52 49 49 44 42 42
1100 1100 1025 980 930 890 820
5.4/7.5 5.4/7.5 7.5/10 13 18 23 23
xx x x x x x
xx x x x x x
350 350 350 350 350 350 300
144 159 201 267 350 400 509
W365H W375H W3105H W3130H W3180H W3240H W3300H
DN20 DN20 DN20 DN20 DN20 DN20 DN20
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"
200-600 200-600 200-600 200-600 200-600 200-600 200-600
50-1000 50-1000 50-1000 50-1000 50-1000 50-1000 50-1000
20 20 20 20 60 60 60
50/75 50/75 50/75 75 75 75 75
170 170 170 170 170 170 170
DN15 DN15 DN15 DN15 DN15 DN15 DN15
1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"
300-600 300-600 300-600 300-600 300-600 300-600 300-600
50-800 50-800 50-800 50-800 50-800 50-800 50-800
Water valves
connection BSP
Rec. water pressure kPa
Functioning limits
for water valve kPa
Capacity
at 300 kPa l/min
Drain valve outer Ø mm
Draining capacity l/min
Steam valve
connection BSP
Rec. steam pressure kPa
Functioning limits for
steam valve kPa
Connections
Technical data
Technical data
Innerdrum
volume litres
diameter mm
Drum speed
wash
extraction rpm
Heating
electricity kW
steam
hot water
G-factor
Weight, net kg

1:2
438 9142-41/04
ABCD E FGH I K LMNOPR S
W365H 720 690 1115 355 720 825 45 1030 220 1010 135 910 830 360 100 240 –
W375H 720 690 1115 355 720 825 45 1030 220 1010 135 910 830 360 100 240 –
W3105H 830 705 1300 365 740 910 45 1115 220 1095 135 995 910 415 100 295 –
W3130H 910 785 1325 435 825 1035 125 1245 215 1225 300 1125 – – 100 305 455
W3180H 970 870 1410 470 910 1120 115 1330 230 1290 315 1205 370 410 100 335 485
W3240H 1020 915 1445 500 955 1155 100 1360 215 1320 300 1240 350 360 100 360 510
W3300H 1020 1060 1445 500 1135 1155 100 1360 215 1320 300 380 – – 100 360 330
A
D
C
9
10
8B
E
O
N
P
R
F
L
GI
1
2
34
5
6
7
5281 5282 5283
K
M
6
W365H, W375H, W3105H, W3130H
5377 5379 5378
9
10
8
D
C
B
6
E6RP
KH
M
GS
5
1
2
3
2
47
LI
W3180H, W3240H, W3300H
A
F
Technical data
Rear side
1Electrical connection
2Cold water
3Hot water
4Hard water
5Steam connection
6Drain
7Liquid detergent supply
8Control panel
9Soap box
10 Door opening, W365H, W375H: ø 310, W3105H: ø 365, W3130H: ø 395, W3180H, W3240H: ø 435
Right sideFront Rear side
Right side
Front

1:3
438 9142-41/04
W365H W375H W3105H W3130H W3180H W3240H W3300H
18.3 18.7 17.1 16.4 15.5 14.8 13.7
1.6±0.5 1.8±0.5 2.3±0.5 3.0±0.5 3.9±1.0 4.5±1.0 5.5±1.3
Technical data
Frequency of the
dynamic force
Hz
Max floor load
at extraction kN

2:1
438 9142-61/04
5325
2
5326
3
5327A
1
Installation
Transportation and unpacking,
W365H, W375H, W3105H
The machine is delivered complete with expan-
sion bolts etc. packed inside the machine in the
drum.
The machine is delivered bolted onto the trans-
port pallet and packed in a crate or box.
• Remove packing from the machine.
• Remove front panel. Remove the bolts bet-
ween the machine and pallet.
• Mount front panel.
When the machine is lifted off the pallet: Make
sure that the machine does not come down on
the floor with either of the rear corners first. The
side panel of the machine can be damaged.
• Mount the feet.
• Place the machine on its final position.
• Level the machine with the feet of the machi-
ne.
The machine also comes with transport safety
devices (four plate angles between the support
and the drum).
In order to remove the safety devices:
• Remove front and rear panel.
• Remove both front metal angels.
• Remove both rear metal angels.
• The machine may not be moved with the
transport securities removed. Save the trans-
port securities for future use.
Fig.
1
Fig.
2
Fig.
3

2:2
438 9142-61/04
5340
4
6445
5
5341
6
Installation
Transportation and unpacking,
W3130H, W3180H, W3240H, W3300H
The machine is delivered complete with expan-
sion bolts etc. packed inside the machine in the
drum.
The machine is delivered bolted onto the trans-
port pallet and packed in a crate or box.
• Remove packing from the machine.
• Remove front and rear panel. Remove the
bolts between the machine and pallet.
• Mount front and rear panel.
• Mount the feet.
NOTE!
Regarding W3300H note the positioning of
the two front feet.
• Place the machine on its final position.
• Level the machine with the feet of the machi-
ne.
The machine also comes with transport safety
devices (two plate angles between the support
and the drum).
In order to remove the safety devices:
• Remove the two side panels.
• Remove the two transport securities.
• The machine may not be moved with the
transport securities removed. Save the trans-
port securities for future use.
Fig.
1
Fig.
4
Fig.
6
Fig.
5

3:1
438 9142-81/01
5327
1
Siting and floor
Install the machine close to a floor drain or open
drain.
In order to make installation and servicing the
machine easier the following clearances are
recommended:
• At least 500 mm between the machine and the
wall behind
• and min. 50 mm on both sides of the machine
whether installed next to the wall or other
machines.
Installation
Fig.
1

4:1
438 9143-01/05
5358
1
A
C
E
B
D
G
F
H
= position of feet
= drilling points for expander bolts
• The machine shall be lifted in the bottom
frame.
• Place the machine over the two drilled holes.
• Check that the machine is placed in level.
Adjust with the feet.
It is of utmost importance that the machine
is placed in level, from side to side as well
as front to rear. If the machine is not pro-
perly leveled, it may result in out-of-balance
without a real out of balance in the drum.
• Insert the expansion bolts supplied in the
holes drilled in the floor. Fit the washers and
nuts, and tighten well.
Mechanical installation
• Mark and drill 2 holes (ø 8 mm) about 40 mm
deep (W365-W3105) and ø 10 mm and 50 mm
deep (W3130-W3240) in the positions shown.
Installation
Fig.
1
Front
A B C D E F G H
W365H 495 460 110 130 375 170 40 100
W375H 495 460 110 130 375 170 40 100
W3105H 575 465 130 140 455 185 35 95
W3130H 635 490 135 175 515 195 60 110
W3180H 715 545 125 205 595 185 60 115
W3240H 790 615 115 180 670 175 60 115
W3300H 903 835 60 180 670 175 60 75

5:1
438 9143-21/07
Installation
Water connections
All intake connections to the machine are to be fitted with manual shut-off
valves and filters, to facilitate installation and servicing.
Water pipes and hoses should be flushed clean before installation. After
installation hoses should hang in gentle arcs.
All connectors present on the machine must be connected up. The
table shows the possible connection options, which will depend on the
water types to be connected to the machine. Check the machine plates too.
All water connectors must be connected up, otherwise the wash
program will not function correctly.
Hoses are to be of an approved type and grade, to comply with national
regulations.
The water pressure data is as follows:
•min: 50 kPa (0,4 kp/cm2)
•max: 1 MPa (10 kp/cm2)
•recommended: 200-600 kPa (2-6 kp/cm2)
If the water pressure is below the min. value, the wash result
can not be guaranteed for certain program.

5:2
438 9143-21/06
1
5336
3
5339
2
5328
1
1
2
3
2
1
W365H,
W375H/N,
W385N/M
W365H,
W375H/N,
W385N/M,
W3105H/N/M
W3130H/N/M
W3180H/N/M,
W3240H,
W3250N/M,
W3300H
W3330N
4
4
4
Installation
Water type Water connection
123 4
cold cold **
cold and
hot cold hot **
cold and
hot cold hot cold*/ **
hot
* For detergent container.
** Only machine with Clarus Control.
Extra water valve which can be used for hard
water if soft water is connected to 1.
This valve can also be used for water reuse
from tank.
If pump is used, it is only a water connection
without valve.
Fig.
1
Fig.
2
Fig.
3

6:1
438 9143-41/02
5330
1
Drain connection
Connect a 75 mm (3") (alt. 50 mm, 2" and only
W365-W3105) pipe or rubber hose to the
machine’s drain pipe, ensuring a downward flow
from the machine. Avoid sharp bends which may
prevent proper draining.
The drainage pipe should be located over a floor
drain, drainage channel or the like so that the
distance between the outlet and the drain is at
least 25 mm (1").
Installation
Fig.
1

7:1
438 9162-01/02
1
5861
3
5863
2
5862
A
3
5865
2
5864
X46
Steam connection
The steam supply to the machine should be fitted
with manual shut-off valves and filters to facilitate
installation and servicing.
The connection hose must be of type ISO/1307-
1983 or equivalent. Connection size at filter:
DN 15 (BSP 1/2").
Steam pressure required:
•minimum: 50 kPa (0.5 kp/cm2)
•maximum: 800 kPa (8 kp/cm2)
•Remove the cover (A).
•Mount the articulated nipple to the steam
valve.
•Mount the steam valve on the machine.
•Mount nipple, strainer and elbow. Note the
direction of the strainer. Mount steam hose to
the elbow.
Check that there are no sharp angles or bends
on the connected steam hose.
•Mount the hose with wires between steam
valve and machine.
Connect wires in the steam valve.
Connect ground cable to the terminal ground
connection.
Mount the cable connector on X46 on
distribution card.
Installation
Fig.
1
Fig.
2
Fig.
3
Fig.
4
Fig.
5