Electrolux W455H User manual

Installation manual
W455H
438 9067-51/EN
06.35

Contents
Contents
Technical data .............................................................................................. 3
Installation .................................................................................................... 7
Siting........................................................................................................ 7
Unpacking ............................................................................................... 8
Mechanical installation ............................................................................ 9
Water supply.......................................................................................... 10
Drain ...................................................................................................... 11
Electrical installation.............................................................................. 12
Machine connection options ................................................................. 13
Connection of external liquid supplies .................................................. 14
Marine installation ................................................................................. 21
Function checks .................................................................................... 23
Safety
This machine can only be used with water. Never use dry cleaning
agents.
Do not allow children to operate the machine.
Do not hose down or spray the machine with water.
All mechanical and electrical installation must be carried out by
qualified personnel.
Do not bypass the door locking device.
Should the machine malfunction, please report the fault to the
technician responsible for the machine.
The manufacturer reserves the right to make changes in design
and materials specifications.

3
Technical data
Technical data
Connections
W455H
Innerdrum, volume litres 53
diameter mm 452
depth mm 332
Drum speed
wash rpm 35/54
extraction 1300
Heating
electricity kW 4.4
steam –
hot water x
G-factor 425
Weight, net kg 102
Water valves connection DN20
BSP 3/4’’
Capacity at 300 kPa
l/min 17
Drain valve outer Ø mm 50
Draining capacity l/min 160

4
C
A
D
2
1
3
B
H
6
G
F
4
5
8
E
6
I
K
B
H
L
7
6206
A B C D E F G H I K L
595 680 850/875* 305 660 80 195 60 90 80 650
1 Control panel
2 Soap box
3 Door opening ø255
4 Cold water
5 Hot water
6 Drain, valve
7 Drain, pump
8Electrical connection
* Adjustable height, 25 mm
Technical data

5
Technical data
Frequency of the
dynamic force Hz 20
Max floor load
at extraction kN 1.2±0.3
Sound levels
A B
Solid sound level in dB (A)
re 10-9 mm/sec (44-707 Hz) 76 62
Airborne sound level
dB (A) re 2x10-5 Pa 51/71* 45/59*
Vibration level
(m/sec2) 0.36 0.66
Vibration speed
(mm/sec) 57 83
A = Standard
B = With insulation
* = Wash/extraction

6

7
1
6216
Installation
Installation
Leave the machine on the pallet on which it was
delivered until the installation site has been pre-
pared to receive it.
Siting
Install the machine close to a floor drain or open
waste water channel.
The following clearances are recommended for
easier installation and servicing:
• at least 500 mm between the machine and the
wall behind it.
• at least 50 mm on each side of the machine,
whether it is next to a wall or to other machi-
nes.
A clearance of 70 mm may be required bet-
ween the machine and the 130-litre tumble
dryer depending on which way the dryer’s
door opens.
Rec.
50 mm
Rec.
500 mm
1

8
6214
6215
3
2
Unpacking
In transit the machine’s drum is locked in place
by three locking devices between chassis and
drum.
Instructions for installing machine and removing
transit locking devices, step by step:
• Remove the packaging.
• Remove the components shipped inside the
drum.
• Remove the front panel by undoing the two
screws on its bottom edge.
• Remove the rear panel by undoing the
screws.
• Remove the three transport securities, one at
the front and two at the back. Save the trans-
port securities if the machine needs to be
moved sometime in the future.
Installation
2
3

9
4
A
C
E
B
D
G
F
H
5358
A B C D E F G H
530 490 35 125 290 150 40 50
Installation
Mechanical installation
• Mark and drill 2 holes (ø 8 mm) about 40 mm
deep in the positions shown.
= position of feet
= drilling points for expander bolts
• The machine shall be lifted in the bottom
frame.
• Place the machine over the two drilled holes.
• Check that the machine is placed in level.
Adjust with the feet.
It is of the upmost importance that the
machine is placed in level, from side to side
as well as front to rear. If the machine is not
properly levelled, it may result in out-of-
balance without a real out of balance in the
drum.
• Insert the expansion bolts supplied into the
holes drilled in the floor. Fit the washers and
nuts, and tighten well.
Front
4

10
2035
5
2030
6
7
2031
Installation
Water supply
Each water supply line to the machine should
be fitted with a manual shut-off valve and debris
filter to facilitate servicing. Check the local regu-
lations to determine whether non-return valves
are required.
Connection hoses should be of the quality re-
quired according to regulations in the country of
use.
Water pressures:
minimum: 40 kPa (0.4 kp/cm2)
maximum: 1 MPa (10 kp/cm2)
recommended: 0.2-0.5 MPa (2-5 kp/cm2)
Hoses and pipes should be flushed through be-
fore being connected to the machine. Make sure
the hoses have no sharp bends or angles.
The machine can have one or two supply hoses,
DN 20 (R 3/4’’).
Machine with cold water intake only.
Machine with hot and cold water intake.
Machine with hot and cold water intake, but
plumbed for cold only because hot not available.
Both valves must be connected even if there is
only one water supply present.
5
6
7

11
650
+50 mm
2029
2036
9
8
Installation
Drain
Direct discharge
Attach the drain hose to the machine’s drain out-
let and install so it empties (min 25 mm) above
the floor drain or waste water channel.
Pump drain
Position the highest part of the drain hose
650±50 mm above the lowest part of the mach-
ine.
Make sure that there are no kinks in the hose.
8
9

12
400-415V 3NAC 50 Hz 4.7 10
230V 3AC 50/60 Hz 4.8 20
230-240V 1AC 50/60 Hz 4.8 25
208-230V 1AC 50 Hz 2.7 16
380V 3AC T 50/60 Hz 3.5 10
400V 3AC T 50/60 Hz 3.8 10
200V 3AC 50/60 Hz 3.8 16
440V 3AC T 50/60 Hz 4.5 10
208-240V 1AC 50/60 Hz 2.7 16
208-240V 1AC 50/60 Hz 0.9 10
200V 1AC 50/60 Hz 1.1 10
Installation
Electrical installation
Electrical installation must be carried out by an authorised electrician.
• Install a multi-pole switch for the machine’s electrical supply.
• Connect the machine’s cable to the switch.
• Check that the earth has been connected in the correct way.
Fuse ratings are given in the table.
For the rating of the supply cable, check the local regulations.
Min. outer diameter for supply cable ø10 mm.
Heating Voltage Total rating Fuse
type type kW A
El. 4.4 kW
El. 4.4 kW
El. 4.4 kW
El. 2,2 kW
El. 3.0 kW
El. 3.3 kW
El. 3.3 kW
El. 4.0 kW
El. 2.2 kW
Non heated

13
301, L 302, 303, N/L
301, 302, L 303
N/L
301
N/L 302
303
L
301 302 303
N/L
L
10
12
13
2068 A
2065 A
2067 A
2066 A
11
Machine connection options
Switchover or reconnection of the machine
may only be performed by qualified, autho-
rised personnel.
This machine can be switched/reconnected fol-
lowing the options set out below.
The machine cannot be switched from
50 Hz to 60 Hz or vice versa.
Reconnection/switchover of this type can-
not be performed on machines fitted with a
transformer.
Connection option 400 V 3NAC 4.4 kW
Connection option 230 V 3AC 4.4 kW
Connection option 230 V 1AC 4.4 kW
Connection option 230 V 1AC 2.2 kW
In cases where the machine data plate
does not state the new voltage option, this
should be added to the plate.
Installation
11
12
13
10

14
14
5881
A
B
6238
6238
15
1 3 5 7 9 11 13 15 17 19
2 4 6 8 10 12 14 16 18
1
4
2
12
15
14 16
13
18
11
Installation
Connection of external liquid
supplies
Machines fitted with connectors
• Connect the pump equipment to connections
A and B on the washing machine.
Connect the signal cable to B and the power
supply to A.
Machines without connectors
• Connect the external pump equipment for
liquid washing detergent to the I/O board,
which is located to the right of the incoming
power supply.
The I/O card has edge connectors for connec-
ting external pumps.
• Edge connectors on the I/O board can be
loosened for connecting cables.
1 = N
2 = L
4 = Ground
11 = N
18 = Program run
12 = Signal 1
13 = Signal 2
14 = Signal 3
15 = Signal 4
16 = Signal 5
14
15

15
16
6236
1
2
3
4
5
7
8
6
9
10
11
12
13
14
15
16
17
18
19
Installation
Outputs
• Connect external power supply (e.g. 24V DC)
for pumps to 9 and 10. If an internal power
supply (from the washing machine) is being
used, it can be taken from 1 (N) and connec-
ted to 9 and from 2 (L) and connected to 10.
Max load on the outputs 0.5 A.
• Signals for pumps 1-5 are connected to 12-16
where connector
12 Washing detergent signal 1
13 Washing detergent signal 2
14 Washing detergent signal 3
15 Washing detergent signal 4
16 Washing detergent signal 5
Inputs
• The signal level can be 5-24V DC/AC or 100-
240V AC. For 5-24V, the signal reference is
connected to 3 and for 100-240V to 4. Poten-
tials on the inputs cannot be mixed.
NB! The I/O board will be damaged if the vol-
tage on connection 3 is too high, >24V.
3M14 3F01 3R01 3F02 Other programs
Signal 1 Prewash Prewash Prewash Prewash Prewash
Signal 2 Mainwash Mainwash Mainwash Mainwash Mainwash
Signal 3 Softener Softener Softener Softener Softener
Signal 4 Mop last rinse Desinfection Pr 1 last rinse Mainwash -
Signal 5 Bleach Bleach Bleach Bleach Bleach
16

16
6265
19
1
2
4
7
18
5964
17
3
8
0V
24V DC
6266
24V
230V
Installation
• Connection 7. If this is connected, an error
message will be displayed if any of the chemi-
cal tanks are empty. The washing program will
continue, however.
• Fit the connecting unions provided and con-
nect the hoses to the unions.
Detergent tank
Empty
Dosing system
Pause signal
• Connection 8 can be connected if the washing program is to pause, e.g. while
washing detergent is being dosed.
17
18
19

17
20
22E
6315
P out
Con 111
Inp opt
/ N inputs
/ L inputs
/ N inp
/ Common 24V
/ Liquid tank empty
/ Temporary paus
/ Heating pause
/ PC5
1 2
1 2
3 4 5 6 7 8
Con 110
1 2 3 4 5 6
9 10
V in
Con 108
1 2
Out 5NO
Con 109
11 12 13 14 15 16
/ Liq 1 / Liq 2 / Liq 3 / Liq 4 / Liq 5
1 2 3 4 5 6
17 18 19
Out CO
Con 107
123
/ 230V..08
/ Prog. run
RE106 RE105 RE104 RE103 RE102 RE101
Function I/O:s
Address
Type of I/O card 2
E
2
Installation
Functions for I/O -cards
• Check the electrical schematic for the machine to find out
what functions are available for the machine.
The electrical schematic can have one of the following:
22E, 22B, 22C or 22D.
20

18
N inputs / .04 N inp / .04
Start 230
Start 24
Common 24V / .04
Common 24V
Supply 0
24V
Supply 24
Program run 1
Program run 1
Central payment
Central payment
L inputs / .04
START / .05START / .05
24V. /
Prog. run / .08Prog. run / .08
.08 .08230V. / .08
P out Inp opt
Con 110
.04 / N inputs
.04 / L inputs
.04 / N inp
.04 / Common 24V
.05 / START
/ Blocking start
/ Liquid tank empty
/ Temporary paus
.05
1 2 1 2 3 4 5 6
1 2 3 4 5 6 7 8
V in
Con 108
1 2
9 10
Out 5NO
Con 109
/ Liq 1 / Liq 2 / Liq 3 / Liq 4 / Liq 5
1 2 3 4 5 6
11 12 13 14 15 16
Con 107
123
17 18 19
Out CO
/ 24V/230V
.08
.08 / Prog. run
RE106 RE105 RE104 RE103 RE102 RE101
Address
Type of I/O card
Function I/O:s
2
B
2
20
22B
6316
Installation