eletab ELTGM03-2 User manual

EleT[email protected] www.facebook.com/EleTabus

CAUTION:
IMPORTANT:
Read the entire instrution manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, Please
contact at [e-mail] for assistance.
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
Ensure that you have received all parts according to the component checklist prior to
installation. If any parts are received damaged or defective, please contact us at
[e-mail]. We are happy to replace parts to ensure you have a fully
functioning product.
• Mounts must be attached as specified in assembly instructions. Improper installation
may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by
professionals.
• Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
• This procuct is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
270
360
180
180
100mm
min10mm-max85mm
75mm
100mm
115mm
75mm
100mm
115mm
min170mm-max505mm
-90
+90
210mm min255mm-max315mm 80mm
50mm
PRODUCT LINE GRAPH

Tools required
Components
Hardware
Parts
L(1)
4mm Allen
Wrench
B (x2)
VESA Plate
H (x1)
Base Support
I (x1)
Support Plate
J (x1)
Knob
K (x2)
Pad
D5 (x4)
M-C
Washer
M5x12mm (x4)
M-B
Screws
M4x12mm (x4)
M-A
Thumbscrews
C (x1)
Clamp Base
Support
D (x1)
Clamp
E (x1)
Cable Clip
F (x1)
Long Screw
G (x5)
Bolt
M(x1)
6mm Allen
Wrench
A (x1)
Arm
(not included)
Phillips
Screwdriver
X2

OPTION A: Clamp Installation
Install clamp base support (C) onto base of monitor stand (A) with bolts (G)
using provided 4mm Allenwrench (L). Apply pads (K) to bottom of base.
Secure clamp (D) to upper two holes with
bolts (G) using 4mm Allen wrench (L) for
desks with a thickness of 10-55mm.
Secure clamp (D) to lower two holes with
bolts (G) using 4mm Allen wrench (L) for
desks with a thickness of 50-85mm.
STEP 1 Choose a mounting option
3

STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide long screw (F) through the top of the grommet base support (H) and install on base of
monitor stand with bolts (G) using 4mm Allen wrench (L). Apply pads (K) to bottom of base.
Position stand on desk with long screw through hole, and secure by using the support plate (I)
and clamp knob (J) on underside of the mounting surface.
Attach base support cover (E)to clamp base support (C). Tighten the clamp to the
desktop using the plastic knob.

STEP 2 Attach the monitors to the arm
Position VESA plate (B) on back of monitor and
secure with screws (M -A) or (M-B) with (M-C)
washers.
Pull the tab on the spring arm (A) ① and slide the VESA
monitor mount and monitor into the mount on the
spring arm.②

Adjust gas spring tension by turning
screw with 6mm Allen wrench (M) .
Clockwisereduces tension, counter
clockwise increasestension. The tension
should be just enough tohold your
monitor in place without lifting itself up.
On the bottom portion of the spring arm,
slide the cable cover up and away from the
spring arm. On the upper portion of the
spring arm, pull the ends of the cable cover
away from thespring arm①, and remove
the cable cover from the spring arm.②
Pull out the ends of the cable cover and insert
the tabs on the inside of the cable cover into
the holes on the spring arm① and reattach
the cable cover.②
If needed, adjust the bolt on
the side of the hinge behind
the VESA plate to tighten or
loosen the tilt angle support.
Be sure to keep the arm in horizontal
position during adjustment .0r else it
would be difficult to adjust the mount or
damage the mount.
STEP 3 Adjust the tension
STEP 4 Cable management

EleT[email protected] www.facebook.com/EleTabus
WARRANTY SERVICE
Feedback
To provide the best service to you, don’t forget to register
your EleTab product to confirm your warranty.
It only takes a few simple steps and then you can access a
wide-range of services such as technicalsupport, new products
alert, promotions, and warranty service from EleTab.
Let us know with a customer review.
Love it? Hate it?
EleTab is committed to delivering customer-driven products that
live up to you high standards. We encourage you to write a
review sharing your experierience.
Should you have any issues, please don't hesitate to contact us.
Scan the qr code above for watching the video of installation
For further services:
Send your name and order ID to EleTab_ser[email protected]