eletab ELTGM01-2 User manual

ELTGM01-2
[email protected]www.eletabergo.com www.facebook.com/EleTabus
(2~8kg)x2
(4.4~17.6lbs)x2
RATED

PRODUCT LINE GRAPH
CAUTION:
IMPORTANT:
Read the entire instrution manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, Please
contact at [email protected] for assistance.
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
Ensure that you have received all parts according to the component checklist prior to
installation. If any parts are received damaged or defective, please contact us at
[email protected]. We are happy to replace parts to ensure you have a fully
functioning product.
• Mounts must be attached as specified in assembly instructions. Improper installation
may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by
professionals.
• Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
• This procuct is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
01
min10~max85mm
min10~max85mm
min258~max300mm
min120~max370mm
50mm
170mm
75mm
100mm
115mm
75mm
100mm
115mm
+45°
-45°
61mm
±180°
±180°
±180°
±90°

Tools required
Components
Hardware
Parts
N(x1)
4mm Allen
Wrench
O(x1)
5mm Allen
Wrench
B (x2)
Head
C (x2)
VESA Plate
I (x1)
Base Support
L(x2)
Support Plate
J (x1)
Knob
K (x5)
D (x1)
Clamp Base
Support
E (x1)
Clamp
F (x1)
Cable Clip
G(x1)
Long Screw
H(x1)
BoltBolt
P (x1)
6mm Allen
Wrench
A (x1)
Arm
(not included)
Phillips
Screwdriver
M4x12mm (x4)
M-A
M4x16mm (x4)
M-B
M6x12mm (x4)
M-C
M6x16mm (x4)
M-D
D6 (x4)
M-E
M-F (x4)
M(x8)
Pad
02
x2

OPTION A: Clamp Installation
Install clamp base support (D) onto base of monitor stand (A) with bolts (K)
using provided 4mm Allen wrench (N).
STEP 1 Choose a mounting option
Apply pads (M) to bottom of base to prevent table top from being scratched.
03
N
K
A
D
M

Secure clamp (E) to upper two holes with
bolts (K) using 4mm Allen wrench (N) for
desks with a thickness of 10-55mm.
Secure clamp (E) to lower two holes with
bolts (K) using 4mm Allen wrench (N) for
desks with a thickness of 50-85mm.
Adjust the Mount to the Desktop
Thickness 10-55mm
Adjust the Mount to the Desktop
Thickness 50-85mm
Attach base support cover (F) to clampbase support (D). Tighten the clamp to the
desktop using the plastic knob.
04
NK K N
E
10-55mm 50-85mm
E
F

STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide long screw (G) through the top of the grommet base support (H) and install on base of
monitor stand with bolts (K) using 4mm Allen wrench (N).
Position stand on desk with long screw through hole, and secure by using the support plate (I)
and clamp knob (J) on under side of the mounting surface.
Apply pads (M) to bottom of base to prevent table top from being scratched.
05
N
A
H
K
G
M
J
I

1. Loose the screw little bit to ensure the distance between two plastic spacers is more than 4mm
2. Attach the Head(B) to monitor arm
3. tight the screw to secure
STEP 2 Head attachment process
STEP 3 Attach the monitors to the arm
OPTION A:Flat Back Monitor
Attach the VESA plate (B) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E).
Avoid excessive tightening screws damage the monitor.
B
M-A
M-C
M-E
P
B
≥4mm
P
P
06

OPTION B:Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-B) or ((M-D) with washers (M-E)and
washers(M-F). Avoid excessive tightening screws
damage the monitor.
Attach the monitors whith VESA to the arm. Use screws ( L ) to tight them.
B
M-E
M-F
M-B
M-D P
L
07

STEP 4 Adjust the tension
Note: If the clockwise rotation is too tight,
the spring will be too dull and it is difficult
to adjust the arm up and down.
We suggest not to adjust it to be too tight,
but to control your strength.
Adjust the spring tension until it supports your monitor to an optimal position.
The initial spring setting will be in a reasonable range, and generally you don't need to adjust the
spring tension.
Case 1: Monitor/Arm falls down (after install your monitor)
If your monitor is too heavy and causes the monitor to sink, turn clockwise to increase spring
tension till it can hold the weight of your monitor. (Press the arm to make it keep it in horizontal
position and then use the Allen Key to adjust the screw on the arm. )
fall down
08
O
O

pop up
Case 2 : Monitor/Arm pops up (after install your monitor)
If your monitor is too light to pop up, or if you accidentally adjust the tension counterclockwise
causing the upper arm to pop up, please adjust the tension clockwise to the appropriate tension!
At this time, we suggest not to
adjust it to be too tight, other
than spring will be too dull and
it is difficult to adjust the arm up
and down.
Case 3: Monitor tilt forward
If needed, adjust the bolt on the side of the hinge behind the VESA plate to tighten the
tilt angle support.
P
09
O

Insert the cable and slide the cable cover down to reattach the cable cover.
STEP 5 Cable management
Just slide the cable cover up and away from the spring arm, do not need to take much effort to
pull the ends of the cable cover away from the spring arm.
10

Love it? Hate it?
Let us know with a customer review.
Feedback
EleTab Team
Welcome to the EleTab family!
Thank you for choosing EleTab products. At EleTab, we truly care about people like you: regular
working people who strive every day to chive a goal, and to make what positive influence they can
in the world with their lives.
That's why we bring this stand to your life, more health and higher productivity. Whatever it is that
leads you to us, were happy that youre here and we want you to know that we understand one
thing: you need a better way to work, a better way to play. Creating an ergonomic work and gaming
environment can really make a huge difference.
We stand behind our products, and we want you to feel secure knowing
that no matter what happens our dedicated support
team can offer immediate assistance with rapid response times.
Our aim has been to create a stand that has it all— it's attractive, balanced, affordable, and
easy to assemble. Does this item meet your expectations? We encourage you to write a review
sharing your experience.
keeping on winning.