eletab ELTGM05-1 User manual

EleT[email protected] www.facebook.com/EleTabus
ELTGM05-1 1.5~8kg
(3.3~17.6lbs)
RATED

CAUTION:
IMPORTANT:
Read the entire instrution manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, Please
contact at [e-mail] for assistance.
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
Ensure that you have received all parts according to the component checklist prior to
installation. If any parts are received damaged or defective, please contact us at
[e-mail]. We are happy to replace parts to ensure you have a fully
functioning product.
• Mounts must be attached as specified in assembly instructions. Improper installation
may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by
professionals.
• Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
• This procuct is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
PRODUCT LINE GRAPH
min10~max85mm
75mm
100mm
114mm
75mm
100mm
114mm
±180°
±90°
+45°
-45°
min10~max85mm
100mm
mm514xam~531nim
60mm
min220~max275mm
170mm
±180°
±180°

Tools required
Components
Hardware
Parts
O(x1)
4mm Allen
Wrench
B (x1)
VESA Plate
H (x1)
Support Plate
I (x1)
Nut
J (x1)
Washer
K (x1)
Security Nut
L (x2)
Bolts
M (x3)
Bolts
N (x4)
Pad
M4x12mm (x4)
M-A
Screws
M4x16mm (x4)
M-B
Screws
M5x12mm (x4)
M-C
Screws
M5x16mm (x4)
M-D
Screws
D5 (x4)
M-E
Washer
M-F (x4)
M-F
Washer
C (x1)
Clamp Base
Support
D (x1)
Clamp
E (x1)
Cable Clip
F (x1)
Long Screw
G (x1)
Base Support
P (x1)
6mm Allen
Wrench
Q (x1)
Wrench
A (x1)
Arm
(not included)
Phillips
Screwdriver

OPTION A: Clamp Installation
Install clamp base support (C) onto base of monitor stand (A) with bolts (M)
using provided 4mm Allen wrench (O).
Apply pads (N) to bottom of base to prevent table top from being scratched.
STEP 1 Choose a mounting option
M
O
A
C
N

Secure clamp (D) to upper two holes with
bolts (L) using 4mm Allen wrench (O) for
desks with a thickness of 10-55mm.
Secure clamp (D) to lower two holes with
bolts (L) using 4mm Allen wrench (O) for
desks with a thickness of 50-85mm.
Attach base support cover (E)to clamp base support (C). Tighten the clamp to the
desktop using the plastic knob.
D
10-55mm
L
O
D
50-85mm
L
O
E

STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide long screw (F) through the top of the grommet base support (G) and install on base of
monitor stand with bolts (M) using 4mm Allen wrench (O). Apply pads (N) to bottom of base.
Position stand on desk with long screw through hole, and secure by using the support plate (H)
and washer (J) on underside of the mounting surface, tighten the nut (I) with wrench (Q).
G
M
F
O
N
H
J
IQ

OPTION A: Flat Back Monitor
STEP 2 Attach the monitors to the arm
Attach the VESA plate (B) to back of monitor and secure with screws (M-A) or (M-C) with
washers (M-E). Avoid excessive tightening screws damage the monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure with screws (M-B) or (M-D) with
washers (M-E) and washers (M-F). Avoid excessive tightening screws damage the monitor.
B
M-A
M-C
M-E
TV
TV
TV
M-B
M-D
M-E
M-F
B

Slide the monitor onto the head of swivel arm, install the security nut (K). Make
sure the security nut is installed before you rotate the monitor.
Adjust gas spring tension by turning
screw with 6mm Allen wrench (P) .
Clockwise(" - " direction) reduces
tension, counter Clockwise("+"
direction increases tension. The tension
should be just enough to hold your
monitor in place without lifting itself
up.
Be sure to keep the arm in horizontal
position during adjustment .0r else it
would be difficult to adjust the mount or
damage the mount.
If needed, adjust the bolt on
the side of the hinge behind
the VESA plate to tighten or
loosen the tilt angle support.
STEP 3 Adjust the tension
K
P
P

STEP 4 Cable Management
For both bottom and upper portion of the spring arm, just slide the cable cover up and away
from the spring arm, do not need to take much effort to pull the ends of the cable cover
away from the spring arm.
On the bottom portion of the spring arm, insert the cable and slide the cable cover down;
On the upper portion of the spring arm, press the tabs on the inside of the cable cover
slightly inward and slide down to reattach the cable cover.
1
2

EleT[email protected] www.facebook.com/EleTabus
WARRANTY SERVICE
Feedback
To provide the best service to you, do not forget to register
your EleTab product to confirm your warranty.
It only takes a few simple steps and then you can access a
wide-range of services such as technical support, new products
alert, promotions, and warranty service from EleTab.
Let us know with a customer review.
Love it? Hate it?
EleTab is committed to delivering customer-driven products that
live up to you high standards. We encourage you to write a
review sharing your experierience.
Should you have any issues, please don't hesitate to contact us.
Scan the qr code below for more products from EleTab
For further services:
Send your name and order ID to EleTab_ser[email protected]