Elpro Technologies 905U-K User manual

`
For 905U-1,2,3,4, C and G products, refer to separate User Manuals
ELPRO Technologies Pty Ltd, 9/12 Billabong Street, Stafford Q 4053, Australia.
Tel: [phone] Fax: [phone] Email: [e-mail]
Web: www.elprotech.com
User Manual
905U-K Wireless I/O

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 2
Thank you for your selection of the 905U product. We trust it will give you many
years of valuable service.
ATTENTION!
Incorrect termination of supply wires may
cause internal damage and will void warranty.
To ensure this product enjoys a long life,
double check ALL your connections with
the user’s manual
before turning the power on.
CAUTION:
This device should not be operated within 8 inches (20cm) of people, in accordance with
CFR 47 Section 1.1307
DO NOT:
•operate the transmitter when someone is within 20 cm of the antenna
•operate the transmitter unless all RF connectors are secure and any open connectors are
properly terminated.
•operate the equipment near electrical blasting caps or in an explosive atmosphere
All equipment must be properly grounded for safe operations. All equipment should be serviced
only by a qualified technician.

User Manual
man_905K_1.10.doc Page 3
FCC Notice: 905U-K Wireless I/O Module
This Users Manual is for the ELPRO 905U-K wireless I/O module. This device complies with
Part 15.247 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference and
2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment is suitable for use in Class I Division 2 groups A, B C and D or non-
hazardous locations only
This device must be operated as supplied by ELPRO Technologies. Any changes or
modifications made to the device without the written consent of ELPRO Technologies may void
the user’s authority to operate the device.
This device MUST be installed by Professional Radio and Antenna personnel. Standard antenna
cables, and antennas must be used, these are available from vendors specified by ELPRO
Technologies. Please contact ELPRO Technologies for end user antenna and cable
recommendations.
Notices: Safety
Exposure to RF energy is an important safety consideration. The FCC has adopted a safety
standard for human exposure to radio frequency electromagnetic energy emitted by FCC
regulated equipment as a result of its actions in Docket 93-62 and OET Bulletin 65 Edition 97-
01.

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 4
Important Notice
ELPRO products are designed to be used in industrial environments, by experienced industrial
engineering personnel with adequate knowledge of safety design considerations.
ELPRO radio products are used on unprotected license-free radio bands with radio noise and
interference. The products are designed to operate in the presence of noise and interference,
however in an extreme case, radio noise and interference could cause product operation delays or
operation failure. Like all industrial electronic products, ELPRO products can fail in a variety
of modes due to misuse, age, or malfunction. We recommend that users and designers design
systems using design techniques intended to prevent personal injury or damage during product
operation, and provide failure tolerant systems to prevent personal injury or damage in the event
of product failure. Designers must warn users of the equipment or systems if adequate protection
against failure has not been included in the system design. Designers must include this Important
Notice in operating procedures and system manuals.
These products should not be used in non-industrial applications, or life-support systems,
without consulting ELPRO Technologies first.
1. For 905U modules, a radio licence is not required in many countries, provided the module
is installed using the antenna and equipment configuration complying with the country’s
regulations.. Check with your local distributor for further information on regulations.
2. For 905U modules, operation is authorised by the radio frequency regulatory authority in
your country on a non-protection basis. Although all care is taken in the design of these
units, there is no responsibility taken for sources of external interference. The 905U
intelligent communications protocol aims to correct communication errors due to
interference and to retransmit the required output conditions regularly. However some
delay in the operation of outputs may occur during periods of interference. Systems
should be designed to be tolerant of these delays.
3. To avoid the risk of electrocution, the antenna, antenna cable, serial cables and all
terminals of the 905U module should be electrically protected. To provide maximum
surge and lightning protection, the module should be connected to a suitable earth and the
antenna, antenna cable, serial cables and the module should be installed as recommended
in the Installation Guide.
4. To avoid accidents during maintenance or adjustment of remotely controlled equipment,
all equipment should be first disconnected from the 905U module during these
adjustments. Equipment should carry clear markings to indicate remote or automatic
operation. E.g. "This equipment is remotely controlled and may start without warning.
Isolate at the switchboard before attempting adjustments."
5. The 905U module is not suitable for use in explosive environments without additional
protection.

User Manual
man_905K_1.10.doc Page 5
Limited Warranty, Disclaimer and Limitation of Remedies
ELPRO products are warranted to be free from manufacturing defects for a period of 2 years
from the effective date of purchase. The effective date of purchase is decided solely by ELPRO
Technologies.
This warranty does not extend to:
- failures caused by the operation of the equipment outside the particular product's
specification, or
- use of the module not in accordance with this User Manual, or
- abuse, misuse, neglect or damage by external causes, or
-repairs, alterations, or modifications undertaken other than by an authorised Service Agent.
ELPRO’s liability under this warranty is limited to the replacement or repair of the product. This
warranty is in lieu of and exclusive of all other warranties. This warranty does not indemnify the
purchaser of products for any consequential claim for damages or loss of operations or profits
and ELPRO is not liable for any consequential damages or loss of operations or profits resulting
from the use of these products. ELPRO is not liable for damages, losses, costs, injury or harm
incurred as a consequence of any representations, warranties or conditions made by ELPRO or its
representatives or by any other party, except as expressed solely in this document.

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 6
905U-K Radio Telemetry Module
USER MANUAL
1OVERVIEW---------------------------------------------------------------------------------------- 8
1.1 Input Signals ....................................................................................................................8
1.2 Power Supply...................................................................................................................9
1.3 Radio Transmitter ............................................................................................................9
1.4 Configuration...................................................................................................................9
2OPERATION--------------------------------------------------------------------------------------11
2.1 Normal Operation ..........................................................................................................11
2.2 What information is transmitted over the radio?...........................................................11
2.3 How often is the input information sent by radio? ........................................................11
2.4 Inputs .............................................................................................................................12
2.4.1 Digital Inputs ...................................................................................................................... 12
2.4.2 Pulse Inputs......................................................................................................................... 12
2.4.3 Shaft Encoder Inputs........................................................................................................... 14
2.4.4 Pulse Rates.......................................................................................................................... 14
2.4.5 Analog Inputs...................................................................................................................... 15
2.4.6 Setpoint Status .................................................................................................................... 17
2.4.7 Supply Voltage ................................................................................................................... 17
2.4.8 Low Supply Voltage Alarm (Supply LowVolts)................................................................ 17
2.4.9 Supply Failure..................................................................................................................... 17
2.4.10 Communications Failure..................................................................................................... 17
2.5 How to Design a Remote Monitoring System...............................................................18
2.5.1 Achieving reliable radio transmission ................................................................................ 18
2.5.2 How far will the radio transmit?......................................................................................... 19
2.6 Calculating Power Consumption ...................................................................................19
2.7 Security Considerations.................................................................................................22
3HARDWARE INSTALLATION--------------------------------------------------------------23
3.1 How to mount the 905K.................................................................................................24
3.2 Antenna Installation.......................................................................................................24
3.2.1 Dipole and Collinear antennas............................................................................................ 26
3.2.2 Yagi antenna. ...................................................................................................................... 26
3.3 Connection Plug.............................................................................................................27
PL1-K Plug Lead............................................................................................................................. 28
3.4 Power Supply Installation..............................................................................................28
3.4.1 External Power.................................................................................................................... 28
3.4.2 Battery Pack BU-5.............................................................................................................. 29
3.4.3 External Battery Supplies ................................................................................................... 30
3.5 Input Signal Connections...............................................................................................30
3.5.1 Digital/Pulse Inputs............................................................................................................. 30
3.5.2 Shaft Encoder Connections................................................................................................. 31
3.5.3 Analog Input....................................................................................................................... 31
3.5.4 RS232 serial port ................................................................................................................ 33

User Manual
man_905K_1.10.doc Page 7
4CONFIGURATION------------------------------------------------------------------------------34
4.1 I/O Mapping...................................................................................................................35
4.2 Update Transmission Times ..........................................................................................36
4.3 Digital Inputs .................................................................................................................36
4.4 Analog Input ..................................................................................................................37
4.5 Analog Setpoints............................................................................................................38
4.6 Supply Voltage ..............................................................................................................38
4.7 Pulse Inputs....................................................................................................................40
4.7.1 Manually Setting Counter Values....................................................................................... 42
4.7.2 Shaft Encoder Inputs........................................................................................................... 43
4.7.3 Pulse Rates.......................................................................................................................... 43
4.8 Number of Transmissions..............................................................................................44
4.9 Programming Configurations to Modules .....................................................................44
4.10 Loading Configuration from a Module ......................................................................45
4.11 Print Options...............................................................................................................45
5DIAGNOSTICS AND TESTING--------------------------------------------------------------46
5.1 System Problems............................................................................................................46
5.2 LED Indicators...............................................................................................................46
5.3 Diagnostic Features........................................................................................................46
5.3.1 Read Inputs......................................................................................................................... 47
5.3.2 Setting Counter Values....................................................................................................... 47
5.3.3 Calibrating Analog Input.................................................................................................... 48
5.3.4 Tone Reversals.................................................................................................................... 49
5.3.5 Firmware Version ............................................................................................................... 49
6SPECIFICATIONS ------------------------------------------------------------------------------50
7WARRANTY--------------------------------------------------------------------------------------53

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 8
1OVERVIEW
Note: Please refer to separate User Manuals for the 905U-1,2,3,4 and -C products.
The 905U-K product will be referred to as the “905K” for the rest of this manual to clearly
delineate it from the other 905U products.
The 905K radio telemetry module is an economical solution for the remote monitoring of process
signals. The 905K can connect to digital, pulse or analog signals from process transducers, and
transmit these signal values by radio.
Although the 905K is intended to be simple in its application, it also provides many sophisticated
features. This manual should be read carefully to ensure that the modules are configured and
installed to give reliable performance. The 905K has been designed to use a European licence-
free radio band at 869MHz. The 905K uses the 869MHz 905U module as a receiver, or
repeater. If you have not used 905U modules before, please read the 905U User Manual prior to
reading this manual.
The 905K module is a monitoring only unit -that is, it will only accept input signals and does
not provide output signals. The 905K has an internal radio transmitter; it does not have a
receiver to receive messages from another module.
The 905K transmits the value of an input signal whenever the signal changes, and also after a
pre-configured time. Each transmission message includes error-checking to confirm the validity
of the message. At each transmission, the 905K may be configured to repeat the transmission
several times to ensure that the transmission is received correctly. This is important if the radio
path is marginal (that is, the radio signal is not strong) or if there is a lot of radio traffic on the
radio channel which may corrupt the 905K message. The 905K transmits the input message to a
905U module, which sets an output signal to be the same value as the 905K input, or the 905U
passes the input message to another device (PC or PLC) via its serial port.
For more information on the 905U module, please refer to the 905U User Manual.
The 905K has a heavy duty painted aluminium enclosure, weather-proofed to NEMA 4 / IP66,
except in Class I Div 2 areas. Signal and power connections to the unit are made via a
weatherproof connector at the bottom of the module. Antenna connection is made using a SMA
coaxial connector at the top of the module. Signal and antenna connections should be wrapped
with waterproofing tape to ensure weatherproof integrity.
In North America, the 905K is approved for use in Class I Division 2 areas, however must be
installed inside another NEMA 4 enclosure.
1.1 Input Signals
The 905K module provides two digital/pulse inputs and one analog input for connecting to
process transducers.
Digital Signals
Examples: motor fault, tank overflow, intruder alarm
Pulse signals - use the same input as the digital input

User Manual
man_905K_1.10.doc Page 9
Examples: electricity metering, fluid flow, raingauge, level from a shaft encoder
Analog continuously variable signals (0-20mA, 4-20mA, 0-10mA, 0-10V)
Examples: measured tank level, measured process temperature
Some internal signals may also be transmitted to outputs in the network:
•Setpoint Status (digital signal set or reset depending upon the value of the analog signal
compared to a high and a low setpoint value configured in the 905K)
•Supply Low Voltage (digital signal set when supply voltage is low).
•Supply Voltage (analog value)
•Pulse Rate (analog value proportional to rate of pulse input - available for both pulse inputs)
1.2 Power Supply
The power consumption of the 905K is very small as it conserves power by reverting to “sleep”
mode between transmissions. The 905K can be powered from a 6 - 30 VDC supply. An optional
9VDC battery pack, the BU-5 is available to power the 905K. The battery supply uses six AA
alkaline batteries. More than one BU-5 battery pack can be connected together to supply a 905K.
Other battery supplies can also be used to power the 905K, including a solar panel supply.
The 905K unit provides an internal alarm on low supply voltage - this alarm may be transmitted
by radio for warning purposes. The user can configure the voltage at which the low voltage
alarm activates.
The 905K generates a 24VDC, 50mA supply for powering the analog loop. This supply is
designed to power an analog loop only and should not be used for any other purpose.
1.3 Radio Transmitter
The 905K has an internal frequency hopping radio transmitter that operates on a unlicensed radio
channel at 900 MHz. A radio licence is not required for the 905K in USA, Canada, Australia,
New Zealand and some other countries.
It is suitable for use in utility industries such as electricity, water and gas, as well as a cost
effective solution for short range applications in factories and industrial plants.
To extend radio range, 905U modules can be used as repeaters. Up to five repeaters can be
configured for each input-to-output link. The configuration is done at the 905K module where
the input signal is - no additional configuration is required at the 905U modules. The transmitted
radio message will include the address of repeater modules - modules with these addresses will
re-transmit the messages.
1.4 Configuration
Each module must be configured before it can be used. Configuration is performed using a PC
(or a laptop computer) connected to the module via the internal RS232 port on the 905K. 905K

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 10
configuration software is required and is provided with each order.
Configuring a module requires the entering of “input mappings” and setting operating parameters
for each input. An “input mapping” links an input signal to an output channel at a remote
module (or a “destination address”). An input mapping is entered for each input signal (external
and internal) which is used. Mappings may be inverted such that the output is the reverse value
of the input.

User Manual
man_905K_1.10.doc Page 11
2OPERATION
2.1 Normal Operation
Once configured using the 905K configuration software, the 905K module will normally be in
“sleep” mode to conserve power. During sleep mode, the microprocessor controller powers
down, and the analog loop supply is turned off. The microprocessor will automatically “wake
up” and revert to full operation if a digital/pulse input changes (on to off, or off to on), or every
0.5 seconds to check if a timed update transmission is due to be sent.
Normal operation of the 905K is indicated by a brief flicker of the OK LED light on the front
panel approximately every 10 seconds.
2.2 What information is transmitted over the radio?
The 905K modules transmit the value of the input signal in a data frame. The data frame includes
a system address, and the "address" of the transmitting (or “source”) 905K module and the
receiving (or “destination”) 905U module, so that each transmitted message is acted on only by
the correct receiving unit. The system address is a common address used by all modules in the
same system. This allows multiple systems to operate within the same radio range without
"cross-talk" between systems.
The user configures these addresses as part of the module configuration. Each transmitted
message also includes error checking to ensure that no corruption of the data frame has occurred
due to noise or interference. If repeater modules are being used, then the addresses of these
intermediate modules are also included in the data frame.
The user can configure the 905K to transmit each message from one to five times to ensure that
at least one of the messages is received correctly. Each repeat transmission will occur at random
intervals between 0.5 and 2 seconds.
2.3 How often is the input information sent by radio?
•Change messages. The 905K transmits the value of an input signal whenever the signal
changes.
•Update messages. The input value is also transmitted if the signal has not changed within a
pre-configured update time (configurable 10 seconds to 7 days).
•Paralysis. When a 905K transmits a message for a particular input, the 905K will not
transmit another message for this input within a configured time period. This time is called
the paralysis time, and may be used to prevent a lot of messages being transmitted if an input
changes frequently. The paralysis time may be set from zero to 127.5 seconds for each input.
For example, assume the paralysis time on an input is 30 seconds. If the input changes, then
the 905K will transmit a message, however it will not transmit another message for this input
during the next 30 seconds, regardless of changes to the input signal. Note that paralysis time
does not stop re-transmissions of each message -if the 905K is configured to transmit each

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 12
message three times, then paralysis will not stop this.
Depending on the type of input signal (digital, pulse or analog), the 905K must determine what
type of signal change is required to send a transmission:
2.4 Inputs
2.4.1 Digital Inputs
A digital input can be an external digital input or an internal status input (setpoint status or low
voltage alarm). The 905K will accept digital inputs as voltage-free contacts, NPN devices (such
as proximity switches) or TTL signals. For TTL signals, a 0-1.5V signal will be measured as
on/active/1, and a 3.5-13V signal will be measured as off/inactive/0.
The 905K will transmit the value of the digital input whenever it changes from off to on or from
on to off. A paralysis time may be configured to prevent another transmission within this time.
The 905K will also transmit an update message if a message has not been transmitted for that
input within an “update time”.
There are two update times for each digital input -one for when the input is on, and one for
when the input is off. Each update time may be configured between 10 seconds and 5 days. For
example, a digital input may be configured to update every 1 day when the input is off, but
update every 10 minutes when the input is on. If an update time of zero (or less than 10 seconds)
is selected, then no update messages will be sent.
Overview:
•Input value transmitted on input change
•Update message if the input value has not been transmitted within the configured update time
for that input (10 seconds - 7 days)
•Separate update times for on and off status for digital inputs
•After each transmission, further transmission for that input is disabled for the paralysis time (0
– 127.5 sec).
The time response of the two digital inputs is different. DI1 has a fast response, sensing a
change within 10msec. This means that the overall “input-to-output’ response is approx 50
msec. DI2 is checked every 500msec -the maximum response time of this input could be 550
msec.
2.4.2 Pulse Inputs
Pulse inputs use the same input connection as the digital inputs. The total number of digital and
pulse inputs available is two.
Each pulse input is counted as two 16 bit registers. The first register is the pulse count, and the
second register is the count of “overflows” of the first register -these two registers provide a 32
bit count of the pulse input. Each register can be transmitted individually. A “sensitivity” value
is configured for each pulse input (0 - 32 000). Whenever the pulse count has increased by this
value since the last transmission, the 905K will transmit the new pulse count. In addition, an
update transmission of the pulse count will be transmitted if the pulse count has not been

User Manual
man_905K_1.10.doc Page 13
transmitted for the update time. If an update time of zero is selected, then no update messages
will be sent.
The maximum pulse input is:
300Hz for contact or NPN inputs (1 msec minimum on-time and off-time), or
10KHz (30 µsec minimum on-time and off-time) for TTL inputs. Up to 50KHz can be
achieved on PI2 provided the divider is set such that the scaled count rate is less than 10KHz
(see below).
There is no minimum pulse rate. For PI2, there is a configurable scaling divider (integer 1 –
255). This allows the pulse count to be scaled. If a divider of X is configured, then the pulse
count will increase by 1 for each X input pulses. There is a separate divider for each pulse input.
The divider parameter could be used for the following reasons:
If the pulse count is to be transmitted to a pulse output on a 905U, then the maximum pulse
rate is 100Hz. If the input rate is more than 100Hz, then it can be reduced with the divider.
For example, if the maximum input rate is 300Hz, then the use of a 10 divider will bring the
effective rate down to 30Hz - each output pulse will then represent 10 input pulses.
The divider can be used to scale the pulse count to engineering units. For example, if the
input pulse rate is 7 pulses per m3 of gas, then a divider of 7 will result in a pulse count
corresponding to the number of m3 . Note that the divider must be an integer.
The divider could be used to slow down the pulse rate. If the input pulse rate is 5KHz, then
the base 16 bit counter will overflow in approx 13 seconds. If the overflow counter is not
used, then this may be too fast to be processed by HMI software. If a divider of 100 is used,
then the counter will take over 20 minutes to overflow.
There is no divider for PI1.
If the pulse count is transmitted to a pulse output on a 905U module, the 905U will compare the
input count to its own output count (the count of output pulses), and will then output pulses until
the two counts are the same. If the pulse counts are transmitted to a 905U-C or 905U-G interface
module, then the 905U-C/G will store the pulse count value in an internal register.
For pulse rates higher than 10 Hz, the “Fast Pulsed Inputs” option should be selected. This
increases power consumption of the module significantly and this needs to be considered if using
a battery power supply.
Overview:
•Pulse inputs are counted as 2 x 16 bit registers.
•Pulse count is transmitted when the count has increased by the sensitivity amount since the
last transmission.
•Update message if the input value has not been transmitted within the update time (10
seconds - 7 days).

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 14
•After each transmission, another transmission for that input is disabled for the paralysis time
(0 – 127.5 sec).
•PI2 can be scaled by a configurable divider.
The diagnostics functions of the 905K allow the user to manually set the counter values to any
value (refer section 5 of this manual). On initial start-up of the modules, the counter values will
be zeroed. If the module loses power, the 905K will save the counter values to non-volatile
memory before shutting down - these values will be restored when power is restored.
2.4.3 Shaft Encoder Inputs
The two pulse inputs may be configured to control one up/down count value, for use with
quadrature and incremental shaft encoders. A shaft encoder is a transducer that measures level or
displacement, and has two pulse signals to indicate change of level and direction of change.
Both pulse inputs are read at the same time. The divider parameter on PI2 must be set to 1 for
this application.
If an incremental encoder is used, then the calculated count value is stored in PI1. If a
quadrature encoder is used, then the calculated count value is stored in PI2.
The counter value (or “level position”) can be manually set using the 905K diagnostics features
(refer section 5 of this manual). Initially the counter will need to be “zeroed” when the shaft
encoder is in the “zero level” position.
2.4.4 Pulse Rates
The rate of each pulse count is calculated and can be transmitted as internal analog inputs. The
rate is calculated on the increase of the base counter, not the rate of the input pulses. The
maximum count rate which can be calculated is 1000Hz. For PI1, this is the maximum pulse
rate that can be calculated. For PI2, a divider can be used for pulse rates more than 1KHz. The
pulse rate values can be scaled -that is, the user can configure what pulse rate (0.1 – 1000Hz)
corresponds to maximum analog value (20mA). Each pulse rate can be scaled individually.
Note that this is separate to the divider on PI2 count.
If the pulse inputs are configured for a shaft encoder, a pulse rate is still calculated -
corresponding to rate change of level. A zero rate (“steady level”) will correspond to a 50%
analog signal. The analog signal will be more than 50% if the level is increasing, and less than
50% if the level is decreasing. If an incremental shaft encoder is used, then the rate may be
scaled by scaling PRATE1. If a quadrature encoder is used, scale PRATE2. The scaling value
will determine both the 100% analog signal (e.g. 20mA) and 0% signal (e.g. 4mA). For
example, if a maximum pulse rate of 10Hz is configured, then the analog signal will be:
100% if the encoder increases at 10Hz 50% if the encoder pulse rate is 0
0% if the encoder decreases at 10Hz. 75% if the encoder increases at 5Hz
25% if the encoder decreases at 5Hz
Note that this is only true if the pulse inputs are configured for a shaft encoder. If standard pulse
inputs are used, then 0% analog signal will correspond to zero pulse rate (0Hz).
The pulse rates are treated as analog inputs and follow the rules for an analog input as described

User Manual
man_905K_1.10.doc Page 15
below.
2.4.5 Analog Inputs
The analog input can measure from 0 – 24mA or 0 – 10VDC. Current or voltage input can be
selected by an internal selector (refer Installation section of this manual). The mA input can be
used for conventional 4-20mA signals or 0-10mA or 0-20mA. The voltage input can be used for
0-5 or 0-10VDC signals. The 905K unit is factory configured for a 4-20mA signal, however the
user can calibrate the unit for other ranges. The measurement resolution is 12 bit.
The analog input uses a “sample time” and “warm-up time” configured by the user. The sample
time (0 – 32727 sec or 9.1hours) “wakes” the 905K from sleep mode and turns on the analog
loop supply. The “warm-up time” (0 – 100 seconds) allows the transducer to reach rated
accuracy before the 905K makes a measurement of the analog signal.
For example, if the sample time is 30 minutes and the warm-up time is 10 seconds, then every 30
minutes, the 905K will turn on its analog loop supply and after a further 10 seconds, take a
measurement of the analog signal. After the measurement is taken, the 905K reverts to sleep
mode. The loop voltage available for a transducer is approx. 24VDC.
If the warm-up time is set to the same or more than the sample time, then the analog loop will be
on continuously, and the 905K will measure the signal based on the sample time. For example,
if the sample time is 10 seconds, and the warm-up time 20 seconds, then the analog loop will be
continuously active and a measurement made every 10 secs. If the sample time os set to zero,
then a measurement is made every cycle of the 905K - that is, 0.5 sec.
Note that continuous analog loop operation will result in a short battery life if a battery supply is
used. A solar panel and battery supply is suitable.
If an externally powered analog signal is connected, then the same measurement process as
described above occurs .

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 16
When the 905K takes a measurement, it will transmit the analog value if the value has changed
by more than the pre-configured sensitivity since the last transmission. The sensitivity can be
configured from 0.1% to 75% with a default value of 3%. If the change in the signal since the
last transmitted value is less than the sensitivity, then the 905K will not transmit the analog
value.
The sensitivity value should be selected which is more than the normal analog signal noise. If
the sensitivity is less than the signal noise, then the 905K will send a lot of un-necessary
transmissions, possibly resulting in jamming the radio channel.
An update transmission of the analog value will be transmitted if the analog value has not been
transmitted for during the user-configurable update period (10 seconds - 7 days). If an update
time of zero is selected, then no update messages will be sent.
If the update time expires since the last transmission, then the last measured value will be
transmitted - that is, a new measurement will not be taken. Normally the update time will be
much longer than the sample time. If the update time is less than the sample time, then update
messages may transmit the same value as the previous transmission, as a new measurement has
not yet been taken.
Overview:
•Measurements of the analog signal are determined by the sample time and warm-up time

User Manual
man_905K_1.10.doc Page 17
•Analog value is transmitted if the measured value has increased by the configured sensitivity
amount since the last transmission
•Analog value is transmitted if the input value has not been transmitted within the update time
(10 seconds – 7 days)
•There is no paralysis time for the analog input.
2.4.6 Setpoint Status
The setpoint status is an internal status value, calculated by comparing the analog input to two
configurable setpoint values. The setpoint status turns ON when the analog input moves below
the low setpoint value, and turns OFF when it moves above the high setpoint value. The high
setpoint percentage must always be greater than, or equal to, the low set point.
The internal setpoint status will be determined every time an analog measurement is taken.
The setpoint status is treated as a digital signal and its value is transmitted according to the rules
for a digital input.
2.4.7 Supply Voltage
The 905K measures the supply voltage and stores it as an internal “analog” value. The range of
the analog value is 0 – 30 volts. The measurement is made every time the radio transmits (the
measured value is the “loaded” supply voltage) and the measurement is transmitted based on the
user-configurable update time - there are no change transmissions for this value.
2.4.8 Low Supply Voltage Alarm (Supply LowVolts)
If the voltage of the power supply falls below the pre-configured alarm value, the internal low
voltage alarm will turn on. The 905K provides user-configurable high and low setpoints for the
supply voltage value. If the supply voltage falls below the low SP, then the Supply Low Volts
status will turn on. When the supply voltage increases above the high SP, the status will turn
off. The low SP should not be set less than 5.7V.
The Supply Low Volts is treated as a digital signal and its value is transmitted according to the
rules for a digital input.
2.4.9 Supply Failure
The 905K will stop operating if the supply voltage falls below 95% of the Supply LOV value.
Prior to shutting down, the 905K will store the values of the pulse counters in non-volatile
memory. The unit will restart when the supply voltage has increased to the configured high SP
value.
2.4.10 Communications Failure
The 905K cannot provide an indication that its transmitted messages have not been received
successfully.
This indication is however available at the receiving 905U by using the 905U Output Reset on
Comms Fail function. To use this function, map an input that is not being used on the 905K to a

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 18
spare output on the 905U. The unused input can be an internal input such as the Low Voltage
status or Setpoint status, or even the analog input as this can also be mapped to a digital output.
Configure the 905K so that the digital output at the 905U is normally on - you can configure an
input to output mapping to be inverted or direct.
If you configure a reset time to the 905U output, then this output will turn off if it has not
received an update message from the 905K within that time. The 905U output is effectively a
"Communications OK" output - on when communications are OK, and off during
communications failure. Note that the maximum output reset time at the 905U is 32 minutes, so
the update time for the 905K input must be less than this. It is generally a good idea to set the
update time to less than half of the reset time. Then, the 905U must fail to receive two
consecutive update messages - it is possible to miss one update message because of random
noise, but two consecutive failures means that there is a system failure.
For example, if you wish to have a failure alarm within 10 minutes of a system failure, set the
output reset time at the 905U to 10 minutes and the update time at the 905K to 4.5 minutes.
2.5 How to Design a Remote Monitoring System
2.5.1 Achieving reliable radio transmission
A system can theoretically have an unlimited number of 905K modules, but in practice, the
number is limited by the amount of radio traffic on one frequency in the system. When a radio
channel becomes unreliable because of radio traffic, then a second radio channel must be used to
increase the size of the system. This limit is not a function of the number of modules, but the
number of radio messages.
A system comprises 905K and 905U modules -each can transmit input signals. The 905U can
"hear" other radio messages, and will hold off transmitting a message until the radio channel is
clear. The 905K module cannot, and there is a possibility that an individual transmission will
clash with another transmission, and both transmissions will be corrupted. This possibility
increases as the density of transmissions increases. Configuring the re-transmit feature
(transmission of each message several times) will increase the chance of each message being
received successfully, but will increase the overall density of radio traffic.
For large systems, a compromise is required between the number of re-transmissions, and the
update times for each input. High priority inputs should have shorter update times than lower
priority inputs.
The peak transmission density should be calculated for large systems. These values are
calculated by determining the number of transmissions from inputs changing value and the
number of update transmissions per hour.
The probability of success for an individual message depends on the transmission density and the
number of re-transmissions for each message. This is shown in the following graph:

User Manual
man_905K_1.10.doc Page 19
Probability of successful transmission
0%
10 %
20%
30%
40%
50%
60%
70%
80%
90%
100%
0
1000
2000
3000
Messages Per Hour
1
2
3
4
5
Transmissions
per message
This assumes that the radio path is reliable and that there is no other radio users on this radio
channel. If intermediate repeaters are used, then each repeated message should be counted as
another message.
We suggest that you use two transmissions per message -with a higher number for a small
number of high priority inputs.
In addition to the above comments, you need to consider the affect of re-transmissions on other
messages being transmitted from the same 905K module. Once a 905K starts transmitting a
message, all transmissions for this message must be complete before another transmission can
start. The time between retransmissions of the same message is a random time between 0.5 and 2
seconds. For example, if a module is configured to transmit each message 5 times, then each
message will take approx 10 seconds. Another message cannot be transmitted from the same
module until the previous message has finished.
2.5.2 How far will the radio transmit?
The distance that can be reliably achieved will vary with each application and is dependent on
the following factors:
•Type and location of antennas (the higher an antenna is, the further it will transmit)
•Amount of radio interference from other transmitters or radio “noise”
•Obstructions such as buildings, hills or trees in the radio path.
The maximum reliable distance is 20+ miles in USA/Canada (4W RF power permitted) and
20+km in Australia/NZ (1W RF power permitted). To achieve these distance, at least one site
needs to be elevated on a hill or transmission tower - refer section 3.2 for more information).
2.6 Calculating Power Consumption
The following information may be used for calculating power consumption.

905K Radio Telemetry Module User Manual
ELPRO Technologies Pty Ltd 2010 Page 20
Voltage Supply
∆volts (6 – 30)
BU-5 Battery
Pack
mA mAHr
Quiescent
constant regardless of voltage
0.14
3.4 per day
Each radio
transmission
Transmission time 42msec 6V
12V
24V
30V
700
300
180
150
0.005
per transmission
Analog input
measurement Externally powered transducer -constant regardless of voltage 10 Not applicable
(per measurement) Loop Powered Transducer - 12 mA average 355 / ∆0.040 x w-time
per measurement.
Current = (355/9)mA
while warming up and
sampling.
Loop Powered Transducer - 20 mA average
576 / ∆
0.064 x w-time
per measurement.
Current = (576/9)mA
while warming up and
sampling.
Pulse Input
0 - 10 Hz (Slow Pulse Inputs)
0.0025 x f
0.06 x f per day
> 10Hz (Fast Pulsed Inputs)
0.2
4.8 per day
w-time = warm up time in seconds f = average pulse frequency in Hz ∆= supply volts
The overall current or energy requirements may be calculated by using the above figures.
Total energy per day = Quiescent
+ Pulse input (if used)
+ Analog input per measurement x number of measurements per day
+ Radio transmission x number of radio transmissions per day
There is no additional power required for digital inputs.
Where the BU-5 battery pack is used, these figures can be used to determine the expected battery
life. A BU-5 with new batteries has a capacity of 1.7 amphours (1700 mAHr). If two BU-5’s are
connected, the second pack provides an additional 1200 mAHr.
Example:-
An application has one digital input, one pulse input and one analog input. It is powered by a single BU-5 battery
pack. Each radio message is configured to transmit two times.
The total power consumed = power for transmissions + power for analog loop supply + pulse input + quiescent
Power for radio transmissions:-
The configuration parameters, and estimated activity data, for each input are:
Digital input Update time, off state 1 day Update time, on state 15 minutes
Input is expected to be on twice per year for 4 hours
No. of change messages per year = 2 (twice per year) * 2 (on to off and off to on)
= 4
No. of “off” update messages per year = 364 (approximately)