Honeywell Smart IO User manual

MOUNTING INSTRUCTIONS
Smart IO
IO-10MIXR-WE/IO-10MIXR-NWE
SUPPORTED DOCUMENTS
• 31-00427 (Smart IO Datasheet)
• 31-00429 (Smart IO Installation Instructions)
EKeep these instructions together with the
device or with the equipment
documentation! Only qualified personnel
may perform electrical connections for 230
VAC.
FCette instruction est à conserver avec le
contrôleur ou avec la documentation de
l'installation ! Le raccordement électrique
pour le 230 VAC ne peut être effectué
que par le personnel autorisé.
PGuarde estas instruςões junto do regulador
ou junto da documentaςão da instalaςão! A
ligaςão eléctrica a 230 VAC só deve ser
efectuada por pessoal especializado.
DDiese Anleitung ist beim Gerät oder in der
Anlagendokumentation aufzubewahren!
Elektrisches Anschließen von 230 VAC ist
nur durch autorisiertes Fachpersonal
gestattet.
IQueste istruzioni devono essere
conservate insieme al lettore o con la
documentazione dell´impianto! I
collegamenti a 230VCA devono essere
eseguiti da personale qualificato.
SDenna instruktion skall förvaras tillsammans
med regler eller
anläggningsdokumentationen! Elektrisk
anslutning med 230 VAC får endast utföras
av behörig personal.
DK Opbevar denne vejledning sammen med
regler eller med anlægsdokumentationen!
Elektrisk tilslutning for 230 VAC bør kun
foretages af autoriserede personer.
NDenne veiledningen skal oppbevares
sammen med regler eller
anleggsdokumentasjonen! Elektrisk
tilkopling med 230 VAC må kun utføres
av fagfolk.
FI Tätä ohjetta tulee säilyttää laitteen
läheisyydessä tai yhdessä muiden
dokumenttien kanssa! Vain asianmukaiset
oikeudet omaava henkilö saa suorittaa 230
VAC käyttöjännitteen liitäntätöitä.
ES Conserve estas instrucciones con el recalar
o con la documentación de la instalación.
La conexión eléctrica a 230 VCA debe
hacerse solamente por personal
qualificado.
NL Deze handleiding moet bij de regelaar, of
met de documentatie van de installatie
worden bewaard! De elektrische
aansluiting voor 230 VAC mag alleen door
geautoriseerd personeel worden
uitgevoerd.
PL Instrukcję obsługi należy przechowywać
przy urządzeniu albo w dokumentacji
technicznej. Tylko autoryzowany servis jest
upoważniony do podłączenia do 230 VAT.
SC 请将此装配说明书与设备或者与设备的其
他文档保存在一起！ 230 V 交流电的接线
操作仅允许由合格的专业人员执行
TC 請將此裝配說明書與設備或者與設備的
其他文件儲存在一起！
僅能由合格的專業人員進行230 V交流
電的接線作業。
K본 설치 설명서를 해당 장치 또는 관련
문서와 함께 보관하시기 바랍니다.
230VAC 전원 연결은 관련 작업 전문가에
의해 수행되어야 합니다.

SMART IO
31-00428 | Rev.10-20
Part Number: 32350802-001 2
WARNING
Electrical Shock Hazard.
Can cause severe injury, death or property
damage.
Disconnect the power supply before beginning
installation to prevent electrical shock and
equipment damage. More than one power supply
may have to be disconnected.
When Installing This Product
1. Read these instructions carefully. Failure to follow
them could damage the product or cause a hazard-
ous condition.
2. Check the ratings given in the instructions and
marked on the product to make sure the product is
suitable for your application.
3. Installer must be a trained, experienced service tech-
nician.
4. After installation is complete, check the product
operation.
5. Be sure wiring complies with all applicable codes,
ordinances and regulations.
This symbol on our product shows a crossed-out “wheelie-
bin” as required by law regarding the Waste of
Electrical and Electronic Equipment (WEEE) disposal. This
indicates your responsibility to contribute in saving
the environment by proper disposal of this Waste i.e. Do not
dispose of this product with your other wastes. To
know the right disposal mechanism please check the
applicable law.
Regulation (EC) No 1907/2006
According to Article 33 of REACH Regulation, be informed
that this product may contain components with lead (CAS:
7439-92-1) content above the threshold level of 0.1% by
weight.
INTRODUCTION
This document contains mounting instructions for the
Smart IO including the accessories.
Mounting the Smart IO on DIN Rail
The Smart IO can be mounted on the vertical or horizontal
DIN rail. The following procedure applies to both mounting
conditions.
1. Remove the top and bottom terminal covers from
Smart IO using fingers by pushing terminal covers
upwards as shown in the below figure.
2. Extend both red clips to the DIN Rail Release posi-
tion as shown in the below figure.
3. Mount the Smart IO onto the DIN rail and push both
red clips in to secure it in place.
4. Connect the antenna, terminal wires, and Ethernet
cables. See the “Antenna” section on page 3 for
antenna installation. See the Smart IO Installation
guide (31-00429) for wiring connections.
5. Remount the Terminal covers.
WEEE
WEEE Directive 2012/19/EC Waste
Electrical and Electronic Equipment
Directive
• At the end of the product life,
dispose of the packaging and
product in an appropriate recycling
center.
• Do not dispose of the device with
the usual domestic refuse.
• Do not burn the device.
Terminal Cove
r
(Bottom side)
Terminal Cover
(Top side)
Red clip
Wall Mount
DIN Rail Release
DIN Rail Lock
Smart IO
DIN Rail
Red Clip
Local Antenna

SMART IO
3 31-00428 | Rev.10-20
Part Number: 32350802-001
Mounting the Smart IO on a
Wall/Panel Using Screws
1. Remove the top and bottom terminal covers from
Smart IO using fingers by pushing terminal covers
upwards as shown in the below figure.
2. Extend both red clips to the Wall Mount position as
shown in the below figure.
3. Hold the Smart IO along the wall and mark the drill-
ing locations through the red clip slots as shown in
the below figure.
4. Remove the Smart IO from the wall and drill two holes
at the marked locations.
5. Insert anchors (if applicable) into the two mounting
screw holes.
6. Hold the Smart IO along the wall/panel so that the
holes are aligned.
7. Insert the screw into the topside hole first and fasten
with a screwdriver.
NOTE: It is recommended to use the 6-18 1” pan head
Phillips tapping screws.
8. Insert the screw into the bottom hole and fasten with
a screwdriver.
9. Connect the antenna, terminal wires, and Ethernet
cables. See the “Antenna” section on page 3 for
antenna installation. See the Smart IO Installation
guide (31-00429) for wiring connections.
10. Remount the Terminal covers.
Antenna
Smart IO has a local antenna included in the kit. The
antenna is to facilitate wireless communication via Wi-Fi
and Bluetooth with other devices. If the Smart IO is
mounted inside a cabinet/enclosure and you are using the
Local antenna, use an enclosure that is made of a non-
metallic material to achieve a reliable wireless signal.
Replace the local antenna with the Remote antenna when
an extended range is needed or when the IO module is
mounted in a metal cabinet/enclosure. The Remote
antenna has a cable that connects to the Smart IO, and the
antenna is mounted outside the cabinet/closure. When the
Smart IO is mounted inside a metal cabinet/enclosure, the
Remote Antenna is required to achieve a reliable wireless
signal.
Installing the Local Antenna
1. Remove the terminal blocks on either side of the SMA
Connector for easier access to the connector.
2. Insert local antenna terminal nut into the SMA con-
nector.
3. Tighten by turning the base of the antenna clockwise.
Terminal Cover
(Bottom side)
Terminal Cover
(Top side)
Red clip
Wall Mount
DIN Rail Release
DIN Rail Lock
Screw
Panel/Wall
Smart IO
Anchor
Local Antenna
SMA Connector
Local Antenna
Smart IO

SMART IO
31-00428 | Rev.10-20
Part Number: 32350802-001 4
Installing the Remote Antenna
1. Uninstall the Local antenna by turning the base of
the antenna counter-clockwise.
2. Place the Remote antenna where the signal reception
is good.
3. Safely route the Remote antenna wire terminal nut to
the Smart IO.
4. Remove the terminal blocks on either side of the SMA
Connector for easier access to the connector.
5. Insert the wire terminal nut into the SMA connector.
6. Tighten the wire terminal nut by turning the nut
clockwise. Do not overtighten.
7. Remount the terminal blocks.
NOTE: Ferrite ring is not required when the Remote
Antenna is used with the Smart IO.
REMOTE ANTENNA PLACEMENT
• Place and align the antenna in a way that the Wi-Fi
signal does not interfere with many obstacles.
• Obstacles such as metal, steel-reinforced concrete wall
filter ~10-90% of the Wi-Fi signal. Other obstacles such
as drywall, wood, glass filter ~0-10% of the Wi-Fi signal.
• The antenna has a strong signal transmission/reception
from the side. See figure below. Position the sides of the
antenna towards the device it is communicating with
(e.g Gateway/WiFi Node).
• Keep the antenna away from devices that cause wireless
interference such as other Wi-Fi network and
telecommunications equipment.
• Make sure that the antenna is installed perpendicular to
the surface for a good Wi-Fi signal.
• Do not install the antenna close to the floor.
• The Local antenna can be used when the Smart IO is
installed in a plastic cabinet/enclosure.
Removing the Smart IO from the
DIN Rail
1. Remove the Terminal Covers if applicable.
2. Disconnect all the communication and power supply
terminals from the Smart IO.
3. Hold the Smart IO with one hand and insert a flat
blade screwdriver into the bottom red clip slot and
pull the red clip outward to release the Smart IO from
the DIN rail.
4. Repeat the same for the top red clip.
5. Remove the Smart IO from the DIN rail.
Removing the Smart IO from the
Wall/Panel
1. Remove the Terminal covers if applicable.
2. Disconnect all the communication and power supply
terminals from the Smart IO.
3. If the remote antenna is installed, remove the termi-
nal blocks on either side of the SMA Connector for
easier access to the connector. Disconnect the
antenna by turning the antenna wire terminal nut
counter-clockwise.
4. Use a screwdriver to remove the bottom screw first.
5. Hold the Smart IO with one hand and remove the top
screw.
6. Remove the Smart IO from the wall/panel.
SMA Connector
Remote Antenna
Wire Terminal Nut
Smart IO
Gateway/Wi-Fi Node
Gateway/Wi-Fi Node
Gateway/Wi-Fi Node
Surface
Surface
Flat Blade Screwdriver

SMART IO
® U.S. Registered Trademark
© 2020 Honeywell International Inc.
31-00428 | Rev.10-20
Part Number: 32350802-001
Honeywell Building Solutions
Honeywell
715 Peachtree Street NE
Atlanta, GA 30308
customer.honeywell.com
buildingcontrols.honeywell.com
DIMENSIONS
122 mm
(4.80”)
57.5 mm
(2.26”)
130.7 mm
(5.15”)
105 mm
(4.13”)
45 mm
(1.77”)
110 mm
(4.33”)