National Instruments NI 9201 User manual

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra

OPERATING INSTRUCTIONS AND SPECIFICATIONS
NI 9201/9221
8-Channel, 12-Bit Analog Input Modules
ni.com/manuals
DeutschFrançais
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 2 ni.com
This document describes how to use the National Instruments 9201
and National Instruments 9221 and includes specifications and
terminal assignments for the NI 9201/9221. In this document,
the NI 9201/9221 with screw terminal and NI 9201/9221 with
DSUB are referred to inclusively as the NI 9201/9221. Visit
ni.com/info and enter rdsoftwareversion to determine
which software youneed for the modules youare using. For
information about installing, configuring, and programming the
system, refer to the system documentation. Visit ni.com/info
and enter cseriesdoc for information about C Series
documentation.
Note The safety guidelines and specifications in this
document are specific to the NI 9201/9221. The other
components in the system might not meet the same safety
ratings and specifications. Refer to the documentation for
each component in the system to determine the safety
ratings and specifications for the entire system. Visit
ni.com/info and enter cseriesdoc for information
about C Series documentation.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 3 NI 9201/9221
Safety Guidelines
Operate the NI 9201/9221 only as described in these operating
instructions.
Hot Surface This icon denotes that the component may be
hot. Touching this component may result in bodily injury.
Safety Guidelines for Hazardous Voltages
Yo ucan connect hazardous voltages only to the NI 9201/9221 with
screw terminal. Do not connect hazardous voltages to the
NI 9201/9221 with DSUB.
If hazardous voltages are connected to the module, take the
following precautions. A hazardous voltage is a voltage greater
than 42.4 Vpk or 60 VDC to earth ground.
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 4 ni.com
Caution Make sure that devices and circuits connected to
the module are properly insulated from human contact.
Caution When module terminals are hazardous voltage
LIVE (>42.4 Vpk/60 VDC), youmust ensure that devices
and circuits connected to the module are properly
insulated from human contact. Youmust use the NI 9932
connector backshell kit to ensure that the terminals are
not accessible.
Figure 1 shows the NI 9932 connector backshell.
Note Yo ucan use the NI 9932 connector backshell only
with the NI 9201/9221 with screw terminal.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 5 NI 9201/9221
Figure 1. NI 9932 Connector Backshell
Safety Guidelines for Hazardous Locations
The NI 9201/9221 is suitable for use in Class I, Division 2,
Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2,
AEx nC IIC T4, and Ex nC IIC T4 hazardous locations; and
nonhazardous locations only. Follow these guidelines if youare
installing the NI 9201/9221 in a potentially explosive environment.
Not following these guidelines may result in serious injury or
death.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 6 ni.com
Caution Do not disconnect I/O-side wires or connectors
unless power has been switched off or the area is known
to be nonhazardous.
Caution Do not remove modules unless power has been
switched off or the area is known to be nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Zone 2 applications, install the system
in an enclosure rated to at least IP 54 as defined by
IEC 60529 and EN 60529.
Caution For Zone 2 applications, install a protection
device between the input signal and the NI 9201/9221
input terminal. The device must prevent the
channel-to-COM voltage from exceeding 85 V if there is
a transient overvoltage condition.
Special Conditions for Hazardous Locations Use in Europe
This equipment has been evaluated as EEx nC IIC T4 equipment
under DEMKO Certificate No. 03 ATEX 0324020X. Each module
is marked II 3G and is suitable for use in Zone 2 hazardous
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 7 NI 9201/9221
locations, in ambient temperatures of –40 °C ≤Ta ≤70 °C. If you
are using the NI 9201/9221 in Gas Group IIC hazardous locations,
youmust use the device in an NI chassis that has been evaluated as
Ex nC IIC T4, EEx nC IIC T4, Ex nA IIC T4, or Ex nL IIC T4
equipment.
Special Conditions for Marine Applications
Some modules are Lloyd’s Register (LR) Type Approved for
marine applications. To verify Lloyd’s Register certification, visit
ni.com/certification and search for the LR certificate, or
look for the Lloyd’s Register mark on the module.
Caution To meet radio frequency emission requirements
for marine applications, use shielded cables and install
the system in a metal enclosure. Suppression ferrites
must be installed on power supply inputs near power
entries to modules and controllers. Power supply and
module cables must be separated on opposite sides of the
enclosure and must enter and exit through opposing
enclosure walls.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 8 ni.com
Connecting the NI 9201/9221
The NI 9201/9221 provides connections for eight analog input
channels.
Figure 2. NI 9201/9221 Terminal and Pin Assignments
AI0
AI1
AI2
AI3
AI4
AI5
AI6
AI7
NC
COM
0
1
2
3
4
5
6
7
8
9
COM
NC
COM
COM
NC
COM
COM
NC
COM
COM
NC
COM
COM
AI0
NC
AI1
AI2
NC
AI3
AI4
NC
AI5
AI6
NC
AI7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 9 NI 9201/9221
The NI 9201/9221 with screw terminal has a 10-terminal,
detachable screw-terminal connector. The NI 9201/9221 with
DSUB has a 25-pin DSUB connector. Each channel has an AI
terminal or pin to which youcan connect a voltage signal. COM,
the common terminal or pin, is internally connected to the isolated
ground reference of the module.
The NI 9201/9221 channels are isolated from other modules in the
system. The module protects each channel from overvoltages.
Refer to the Specifications section for more information about
overvoltage protection. The input signals are scanned, buffered,
conditioned, and then sampled by a single 12-bit ADC. Refer to
Figure 3 for an illustration of the input circuitry on the
NI 9201/9221.
Figure 3. Input Circuitry on the NI 9201/9221
NI 9201/9221
Buffer Isolated
ADC
Overvoltage
Protection Mux
COM
AI7
AI0
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 10 ni.com
Yo ucan connect single-ended voltage signals to the NI 9201/9221.
Connect the positive lead of the voltage signal to AI. Connect the
ground signal to COM. Refer to Figure 3 for an illustration of
connecting a single-ended voltage signal to the NI 9201/9221.
Figure 4. Connecting a Single-Ended Voltage Signal to the NI 9201/9221
Note Yo umust use 2-wire ferrules to create a secure
connection when connecting more than one wire to a
single terminal on the NI 9201/9221 with screw terminal.
COM
AI
+
–
Voltage
Source
NI 9201/9221
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 11 NI 9201/9221
Wiring for High-Vibration Applications
If an application using the NI 9201/9221 with screw terminal is
subject to high vibration, National Instruments recommends that
youeither use ferrules to terminate wires to the detachable
screw-terminal connector or use the NI 9932 backshell kit to
protect the connections. Refer to Figure 5 for an illustration of
using ferrules. Refer to Figure 1 for an illustration of the NI 9932
connector backshell.
Figure 5. 10-Terminal Detachable Screw-Terminal Connector with Ferrule
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 12 ni.com
Sleep Mode
This module supports a low-power sleep mode. Support for sleep
mode at the system level depends on the chassis that the module is
plugged into. Refer to the chassis manual for information about
support for sleep mode. If the chassis supports sleep mode, refer to
the software help for information about enabling sleep mode. Visit
ni.com/info and enter cseriesdoc for information about
C Series documentation.
Typically, when a system is in sleep mode, youcannot
communicate with the modules. In sleep mode, the system
consumes minimal power and may dissipate less heat than it does
in normal mode. Refer to the Specifications section for more
information about power consumption and thermal dissipation.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 13 NI 9201/9221
Specifications
The following specifications are typical for the range –40 to 70 °C
unless otherwise noted. All voltages are relative to COM unless
otherwise noted. The specifications are the same for the NI 9201
and the NI 9221 unless otherwise noted.
Input Characteristics
Number of channels.......................... 8 analog inputchannels
ADC resolution ................................. 12 bits
Type of ADC..................................... Successive approximation
register (SAR)
Sample rate (aggregate)
Module
Maximum Sample
Rate (R Series
Expansion Chassis)
Maximum
Sample Rate
(All Other Chassis)
NI 9201,
single channel
475 kS/s 800 kS/s
NI 9201, scanning 475 kS/s 500 kS/s
NI 9221 475 kS/s 800 kS/s
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 14 ni.com
Input range
NI 9201....................................... ±10 V
NI 9221....................................... ±60 V
Operating voltage ranges1
Overvoltage protection
(channel-to-COM) ............................ ±100 V
1 Refer to the Safety Guidelines section for more information about safe operating
voltages.
Module
Measurement Voltage,
Channel-to-COM
Maximum Voltage,
Channel-to-Earth Ground or
COM-to-Earth Ground
Min
(V)
Typ
(V)
Max
(V)
Screw
Terminal DSUB
NI 9201 ±10.3 ±10.53 ±10.8 250 Vrms ±60 VDC
NI 9221 ±61.4 ±62.50 ±63.8
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 15 NI 9201/9221
NI 9201 accuracy (excludes noise)
Measurement Conditions
Percent of
Reading
(Gain Error)
Percent of
Range*
(Offset Error)
Calibrated typ (25 °C, ±5 °C) ±0.04% ±0.07%
Calibrated max (–40 to 70 °C) ±0.25% ±0.25%
Uncalibrated typ (25 °C, ±5 °C) ±0.26% ±0.46%
Uncalibrated max (–40 to 70 °C) ±0.67% ±1.25%
*Range equals 10.53 V
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 16 ni.com
NI 9221 accuracy (excludes noise)
Stability
Gain drift .................................... ±34 ppm/°C
Offset drift
NI 9201 ................................ ±100 μV/°C
NI 9221 ................................ ±580 μV/°C
Input bandwidth (–3 dB)
NI 9201....................................... 690 kHz min
NI 9221....................................... 950 kHz min
Measurement Conditions
Percent of
Reading
(Gain Error)
Percent of
Range*
(Offset Error)
Calibrated typ (25 °C, ±5 °C) ±0.04% ±0.07%
Calibrated max (–40 to 70 °C) ±0.25% ±0.25%
Uncalibrated typ (25 °C, ±5 °C) ±0.26% ±0.43%
Uncalibrated max (–40 to 70 °C) ±0.67% ±1.06%
*Range equals 62.50 V
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 17 NI 9201/9221
Input impedance
Resistance................................... 1 MΩ
Capacitance ................................ 5 pF
Input noise (code-centered)
RMS ........................................... 0.7 LSBrms
Peak-to-peak............................... 5 LSB
No missing codes.............................. 12 bits
DNL .................................................. –0.9 to 1.5 LSB
INL.................................................... ±1.5 LSB
Crosstalk (at 10 kHz) ........................ –75 dB
Settling time (to 1 LSB)
NI 9201....................................... 2 μs
NI 9221....................................... 1.25 μs
MTBF ............................................... 1,092,512 hours at 25 °C;
Bellcore Issue 2, Method 1,
Case 3, Limited Part Stress
Method
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

NI 9201/9221 18 ni.com
Note Contact NI for Bellcore MTBF specifications
at other temperatures or for MIL-HDBK-217F
specifications.
Power Requirements
Power consumption from chassis
Active mode ............................... 1 W max
Sleep mode ................................. 1 mW max
Thermal dissipation (at 70 °C)
Active mode ............................... 1 W max
Sleep mode ................................. 32 mW max
Physical Characteristics
If youneed to clean the module, wipe it with a dry towel.
Note For two-dimensional drawings and
three-dimensional models of the C Series module and
connectors, visit ni.com/dimensionsand search by
module number.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© National Instruments Corp. 19 NI 9201/9221
Screw-terminal wiring ...................... 12 to 24 AWG copper
conductor wire with 10 mm
(0.39 in.) of insulation
stripped from the end
Torque for screw terminals ............... 0.5 to 0.6 N · m
(4.4 to 5.3 lb · in.)
Ferrules ............................................. 0.25 mm2to 2.5 mm2
Weight
NI 9201/9221
with screw terminal .................... 150 g (5.3 oz)
NI 9201/9221 with DSUB.......... 145 g (5.1 oz)
Safety
Safety Voltages
Connect only voltages that are within the following limits.
Channel-to-COM .............................. ±60 VDC max
NI 9201/9221 with Screw Terminal Isolation Voltages
Channel-to-channel........................... None
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com