Enrock EMRGB265W Installation instructions

EMRGB265W / EMRGB265B
MARINE GRADE 6.5” 2-Way SPEAKERS
FEATURING 17 COLOR RGB LED’S
AND RF REMOTE CONTROLLER
INSTALLATION / OWNER’S MANUAL
Thank you for purchasing this Enrock 6.5” 2-Way Speakers
Please read through these instructions carefully so you will know how to
operate your model properly.
Keep these instructions in a safe place for future references.
LIMITED WARRANTY
Enrock warrants this product to be free from defects in material
andworkmanship for a period of 90 days from purchase. The Enrock product
is sold with the understanding that the purchaser has
independentlydetermined the suitability of this product. This warranty is
offered to the original purchaser of the product only. This warranty does not
cover the product if physically damaged, subject to negligence or misuse,
abuse, alteration, accident, or an act of GOD. This warranty does not apply to
product which has water or physically damaged by accident or which has
been misused, disassembled or altered.The original dated sales slip or proof
of purchase will establish warrantyeligibility. If the product should prove
defective within the warranty period, return the product with proof of
purchase to Enrock. Enrock, at its option, will replace or repair the product
free of charge and return the product.In no event shall Enrock be responsible
for claims beyond the replacement value of the defective products or in any
way be liable or responsible for consequential or incidental damages. No
implied warranties, whether for fitness or any particular use or otherwise,
except as set forth above (which is made expressly in lieu of all other
warranties) shall apply to products sold by Enrock. Enrock cannot be held
responsible fordiscrepancies/inconsistencies that may occur due to
automotivemanufacturing changes or option.
EMRGB265W / EMRGB265B

EMRGB265W / EMRGB265B
Thank you for purchasing this Enrock 6.5” Coaxial Speakers
With RGB LED RF Controller.
Please read through these instructions carefully so you will know how to
operate your model properly.
Keep these instructions in a safe place for future references.
PACKAGE CONTENTS:
Coax Speakers (2)
RF Remote Controller (1)
RGB LED RF Sync Receiver HUB (1)
HUB Wire Extension Kit (2)
Speaker Wire & Mounting Hardware Kit (2)
User manual / Warranty Card (1)
SAFETY PRECAUTIONS:
Do not turn up the volume so high that you can’t hear what’s around you.
Use caution or temporarily discontinue use in potentially hazardous
situations
Do not operate mobile video equipment while driving a motorized vehicle
Set your volume control at a low setting, then slowly increase the sound
until you can hear it comfortably without distortion or ear discomfort.
Safe vehicle operation and safety consideration of others should always
be your highest priority
In the event you should notice smoke, strange noises or odor from this
product, or any other abnormal signs, immediately turn off the power and
consult your dealer. Using this product in this condition may result in
permanent damage to the system.
INSTALLATION PRECAUTIONS:
Always consult with a professional installer
Use only the installation parts provided with the speaker
The Speakers have a weather resistant design, it should not be
submerged in or under water under any circumstances
The Speakers LED RGB SYNC HUB should be wired directly to a normally
open switch or relay.
When wiring directly to the vehicles batter, be sure to disconnect the
batteries negative terminal wire before starting any wiring procedures, if
extending the main power wire, it is suggested that an optional fuse and
fuse holder (not included) with minimum rating of 10 Amperes be in-line
with the positive battery terminal.
The ground cable length should not exceed 18-inches
Do not attempt to install or service this product by yourself. Installation or
servicing of this product by persons without professional training and
experience in electronic equipment and motorized vehicle accessories
may be dangerous and could expose you to the risk of electric shock,
injury or other hazards.
MODE
MODE
DEMO
SPEED SPEED
COLOR
COLOR
BRIGHT
BRIGHT
Pair Of
Coax Speakers
RF Remote
Controller
RGB LED RF
Sync Receiver HUB
HUB Wire
Extension Kit
Speaker Wire
Mounting Hardware Kit
User manual
& Warranty Card

WIRE DIAGRAM:
Do not touch the speaker flex wire
Secure all wiring with wire ties
Properly seal connections to ensure water tight connections
The RGB HUB controller should be installed in a non-metal and dry location
BEFORE INSTALLING THIS PRODUCT:
To avoid potential shorts in the electrical system, be sure to disconnect
the (-) battery cable before installation. Use this unit with a 12-volt battery
and negative grounding only.
Failure to do so may result in a fire or malfunction.
When replacing the fuse, be sure to only use a fuse of the rating specified on
this product.
To avoid short-circuiting, cover any disconnected leads with insulating tape.
It is especially important to insulate any unused wires, which if left uncov-
ered may cause a short circuit. When connecting other devices to this
product, refer to the manual for the product to be connected. The black
cable is ground, make sure to connect the ground wire first.
Ensure that the ground cable is properly connected to metal parts of the
vehicles body frame or direct to the battery if your vehicle does not have a
grounded chassis frame. The ground cable of this unit’s power amp and a
second powered system must be connected to the frame separately with
different screws. If the screw for the ground wire loosens or falls out, it could
result in fire or malfunction.
TOOLS NEEDED:
GROUND CABLE
METAL FRAME
FUSE REPLACEMENT
WITH ATO TYPE ONLY
3 AMP
SPEAKER 1
SPEAKER 2
+
-
+
-
+12V BATTERY YELLOW
REMOTE OUT
+12V BLUE
+12V RED
CHASSIS
GROUND
POINT
BATTERY
OPTIONAL DIRECT BATTERY WIRING CIRCUIT
BLACK
OPTIONAL
FUSE AND FUSE HOLDER
(NOT INCLUDED)
CHASSIS
GROUND
POINT
Recommended 16 ~ 18ga Primary Extension Wire
(not included)
ON C
Normally Open
ON/OFF ACC switch
Normally open
ACC switch
(not included)
YOUR
BATTERY
KILL SWITCH
RGB LED 2
RGB LED 1
YOUR RADIO
RGB LED 2
RGB LED 1
SYNC OUT
SYNC IN
RGB SYNC HUB
NOTE: ONLY USE SYNC IN/OUT WHEN CONNECTING
TWO OR MORE HUB SYSTEMS TOGETHER
INSERT
INSERT
RGB LED
EXTENSION WIRE
TO CONNECT MORE THAN
ONE SET OF MRGB65 TOGETHER,
PLUG THE SYNC OUT TO THE SYNC
INPUT OF THE NEXT SYSTEM
STRIPPED WIRE NEGATIVE
12FT
Splice BUTT connectors
3A
CAUTION!!!
Do not ground or short the RGB Wires
EMRGB265W / EMRGB265B

SUGGESTED MOUNTING LOCATIONS:
The EMLED65W / EMLED65B can be mounted in three different configura-
tions, Always double check for mounting depth limitations,
Never cut before you check,
GETTING STARTED:
Getting to know your EMLED65W / EMLED65B controller
RF Controller range: up to 25Ft
Do not obstruct the RF remote with metal
Always keep away from small children
Do not store in direct sunlight
Buttons: 6. Brightness Up
1. RF Controller 7. Brightness Down
2. Power on/off 8. Mode Down
3. Mode up 9. Color Down
4. Auto Demo 10. Color Up
5. Speed up 11. Speed Down
MODE
MODE
SPEED SPEED
COLOR
COLOR
BRIGHT
BRIGHT
DEMO
EMRGB265W / EMRGB265B

SPEAKER TEMPLATE:
TEMPLATE FOR REFERENCES ONLY NOT FOR SCALE
SPECIFICATIONS:
SPEAKER GENERAL SPECS
Speaker Type: Full Range
Configuration: Coaxial
Woofer Size: 6.5”
Tweeter Size: 1”
Mounting Depth: 2 5/8”
Mounting Diameter: 5 ¾”
Peak power Handling: 180Watts
Impedance: 4Ohms
Sensitivity: (1W/1M) 88dB
Frequency Response: 70Hz to 20kHz
WATER DRAINAGE HOLE - DO NOT BLOCK
BE SURE TO MOUNT SPEAKER IN THE CORRECT ORIENTATION
TO ALLOW FOR WATER DRAINAGE
Reminder:
To avoid battery exhaustion be sure to run the vehicles engine while using this product.
Using this product without running the engine can drain the battery.
CAUTION!!
Adjustment or alterations of this device may result in hazardous
radiation exposure.
OD
RGB HUB GENERAL SPECS
Power Source: 14.4VDC (10.8V – 16V allowable)
Grounding System: Negative Type
Maximum Current Consumption: 1.5A
Unit Weight: 2.08lb
s
TROUBLE SHOOTING GUIDE
EMRGB265W / EMRGB265B