Equalizer International SWi5TE Assembly instructions

OPERATOR INSTRUCTION MANUAL
SWi5TE
EQUALIZER INTERNATIONAL LTD
www.equalizerinternational.com
FLANGE
SPREADING
WEDGE

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
2
CONTENTS
1. INTRODUCTION
2. TOOL SAFETY
2.1 GENERAL SAFETY
2.2 PERSONNEL COMPETENCY
2.3 DISCLAIMER
2.4 DEFINITION OF TERMS
2.5 HAZARDS
3. SWi SPREADING WEDGE TOOL OPERATION
3.1 GENERAL GUIDANCE
3.2 FLANGE SPREADING
3.3 FLANGE WORK
3.4 FLANGE CLOSURE
3.5 SAFETY BLOCKS
3.6 STEPPED BLOCKS
3.7 HANDLE
3.8 LANYARD
3.9 STEP DIMENSIONS & SPREADING DISTANCES
4. TOOL MAINTENANCE
4.1 INSPECTION
4.2 CLEANING
4.3 SERVICING
4.4 LUBRICATION PROCEDURE
4.5 STORAGE & TRANSPORTATION
4.6 OPERATING CONDITIONS
4.7 SUB-SEA USAGE
5. SWi5TE
5.1 TOOL CAPABILITIES
5.2 TOOL FUNCTION
5.3 KIT CONTENTS
5.4 DIMENSIONS
6. TROUBLESHOOTING
6.1 SWi5TE TROUBLESHOOTING
7. REGULATORY INFORMATION
7.1 REGISTERED HEAD OFFICE
7.2 APPLICABLE PATENT NUMBERS
8. PARTS LISTS & SERVICE KITS
22/07/2018

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
3
2.
TOOL SAFETY
2.1
GENERAL SAFETY
These instructions cover the safe operation and
maintenance of THE EQUALIZER SWi5TE FLANGE
SPREADING WEDGE tool. The use of this tool should be
as part of a broader task-based risk assessment, which
should be carried out by the operation supervisor or other
competent person.
Failure to comply with the safety information contained
within this manual could result in personal injury or
equipment damage. Read all instructions, warnings and
cautions carefully, and follow all safety precautions.
The safety of the operator, any assisting personnel and
the general public is of paramount importance. Always
work in accordance with applicable national, local, site &
company-wide safety procedures.
2.2
PERSONNEL COMPETENCY
Only personnel deemed competent in the use of hydraulic
equipment should use these tools.
2.3
DISCLAIMER
Equalizer cannot be held responsible for injury or damage
resulting from unsafe product use, lack of maintenance
or incorrect product and/or system operation. If in doubt
as to the safety precautions and applications, contact
Equalizer using the contact details at the back of this
manual.
1.
INTRODUCTION
The Equalizer™ SWi5TE has been developed to assist in
the spreading of all ange joint types with a minimum
access gap of 4.0 mm (0.16”). The tool can be used
during pipework construction, commissioning or during
routine maintenance.
The SWi tools have less moving parts and no nger pinch
points. The tools have been developed to increase the
spreading distance on each step while gaining easier
access between any remaining stud-bolts within the
ange joint. The SWi tools are supplied with a swivel
handle and safety lanyard attachment as standard.
It is essential that the user familiarises themselves with
the contents of this manual prior to using the tool.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
4
WARNING: Applying pressure to a damaged
hose may cause it to rupture.
WARNING: Immediately replace worn or
damaged parts. Use only genuine Equalizer
parts from approved distributors or service
centres. Equalizer parts have been engineered
and manufactured to be t-for-purpose.
DANGER: To minimise risk of personal injury
keep hands and feet away from the tool and
workpiece during operation.
WARNING: Always wear suitable clothing and
Personal Protective Equipment (PPE). Do not
handle pressurised hoses; escaping oil under
pressure can penetrate the skin, causing
serious injury. Seek medical attention
immediately if oil penetration is suspected.
WARNING: Only pressurize complete and fully
connected hydraulic systems. Do not pressurize
systems that contain unconnected couplers.
CAUTION: Do not lift hydraulic equipment by
the hoses or couplers. Use only the designated
carrying handles.
CAUTION: Lubricate tools as directed in this
manual prior to operation. Use only approved
lubricants of high quality, following the lubricant
manufacturers instructions.
CAUTION: Only use the designated anchor
point for xing the lanyard. Do not attach the
lanyard to the plastic handle.
DANGER: Care should be taken when using
the lanyard to avoid entanglement with body
parts.
The vibration total value to which this tool is
subjected does not exceed 2.5 m/s2.
2.4
DEFINITION OF TERMS
A CAUTION is used to indicate correct operating or
maintenance procedures and practices to prevent damage
to, or destruction of equipment or other property.
A WARNING indicates a potential danger that requires
correct procedures or practices to avoid personal injury.
A DANGER is only used when your action or lack of
action may cause serious injury or even death.
DO: an illustration showing how the tool should
be used.
DON’T: an illustration showing an incorrect way
to use a tool.
2.5
HAZARDS
WARNING: ensure all hydraulic components
are rated to a safe working pressure of 700 bar
(10 000 psi).
WARNING: Do not overload equipment. The
risk of hydraulic overloading can be minimised
by using the Equalizer Hand Pump, which has a
factory-set safety valve preventing the safe
working pressure being exceeded.
If alternative hydraulic pumps are used, ensure
that there are adequate systems to limit the
working pressure to 700 bar (10 000 psi).
CAUTION: ensure components are protected
from external sources of damage, such as
excessive heat, ame, moving machine parts,
sharp edges and corrosive chemicals.
CAUTION: Take care to avoid sharp bends and
kinks in hydraulic hoses. Bends and kinks can
cause severe back-up pressure and cause hose
failure. Protect hoses from dropped objects; a
sharp impact may cause internal damage to
hose wire strands. Protect hoses from crush
risks, such as heavy objects or vehicles; crush
damage can cause hose failure.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
5
3.2
FLANGE SPREADING
Spread the anges apart by actuating the tool.
Once the joint has been opened to the desired distance,
or if the tool has reached its maximum travel, insert the
Safety Blocks into the ange joint.
Ensure the full width of the selected Safety Block step is
fully inserted before gradually retracting the tool until the
ange load has been applied to them.
The wedges can then be retracted fully and inserted
again, using the next step. In this way the ange joint
can be iteratively opened further until the required spread
is reached.
3.
SWi SPREADING WEDGE
TOOL OPERATION
3.1
GENERAL GUIDANCE
Before attaching the tool ensure at least two ange bolts
remain in place. These should be 180 degrees apart with
their nuts loosened sufciently to enable ange work to
be carried out. Leaving these bolts in place will help to
reduce unwanted lateral ange movement during ange
spreading.
Prior to spreading, an assesment should be carried out to
determine the most appropriate positioning of the tools
around the joint. A minimum of 2 tools should always be
used.
Determine the ange joint access gap - a minimum access
gap of 4 mm (0.16”) is required for the SWi5TE tools. The
access gap is the clearance between the surfaces onto
which the wedge will apply its spreading force.
4.0 mm (0.16”)
MINIMUM
ACCESS GAP
Place the tool into the access gap, with the full width of
the selected step fully inserted up to the heel.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
6
3.5
SAFETY BLOCKS
Each tool is supplied with a Safety Block. The Safety Block
has been designed with steps that match the spreading
distance of the SWi tools.
The Stepped Block Kit contains a larger Safety Block to
cater for wider spreading distances.
3.6
STEPPED BLOCKS
A pair of Stepped Blocks can be supplied as a kit item.
These can be xed to the jaws (individually or in pairs)
to increase the effective jaw thickness and therefore the
maximum spreading distance.
Use of the Stepped Blocks also enables the SWi5TE Flange
Spreader to be used in a joint with a larger access gap.
Wedge protrusion can be minimised by the use of Stepped
Blocks, reducing the penetration into the joint. This
enables, for example, spectacle blinds to be changed.
Attach the stepped block to the tool using the M6 counter-
sunk screw. Use the hex-key supplied to tighten the screw
into the threaded hole in the jaw of the tool. Repeat for
second Stepped Block to further increase the effective jaw
thickness if required.
3.3
FLANGE WORK
DANGER: Do not rely upon hydraulic systems
for supporting the access gap during ange
work. Do not allow ngers, hands or other body
parts into the space created between the
anges.
3.4
FLANGE CLOSURE
Allow the anges to return to their closed position by
gradually retracting the tool. Consult the relevant section
of the manual for instructions on how to retract the tool.
Before the tool has fully retracted, insert the Safety
Blocks into the ange joint. Ensure the full breadth of
the selected Safety Block step is fully inserted, before
gradually retracting the tool until the ange load has been
applied to them.
To use the next smallest step, place the tool in the gap
and actuate enough to relieve the load on the Safety
Blocks. In this way the ange joint can be progressively
closed.
As the ange approaches its fully closed position, support
the tool to avoid it dropping out of the joint. Ensure that
care is taken to prevent objects being dropped. Dropped
objects pose a risk of personal injury or equipment
damage.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
7
3.8
LANYARD
The SWi tools are supplied with a secure anchor point and
a lanyard. The lanyard should be used to minimise the
risks associated with the tool dropping.
Attach one end of the lanyard to the tool using the
supplied shackle. The other end of the lanyard should
be xed to a secure point close to the work-site using an
appropriate shackle.
Avoid using the lanyard as a means for picking up or
carrying the tool. Do not x the lanyard to the handle.
The anchor point and lanyard have been engineered to
safely sustain a drop over the full lanyard length. It is
recommended that all parts are inspected following a drop
incident, as damage may compromise the safety of the
tool.
CAUTION: Only use the designated handle
holes for xing the lanyard. Do not attach the
lanyard to the plastic handle.
DANGER: Care should be taken when using
the lanyard to avoid entanglement with body
parts.
To remove the Stepped Blocks unscrew the M6 counter-
sunk screw. Do not force the screw out of the Stepped
Block, it is deliberately retained to prevent it becoming
misplaced.
Use the tool as per the Tool Operation instructions.
Ensure that there is a minimum hold of 15 mm (0.59”)
and that the full width of the block is used.
15.0 mm (0.59”)
MINIMUM HOLD
3.7
HANDLE
The handle can be swivelled around the central axis of the
tool, to improve access to the Flange and allow the tool
to be easily held in the vertical or horizontal orientation.
If the tool is being used in an application where access
space is very limited, the handle can be removed
temporarily. Remove circlip and handle. Special caution
should be exercised when working with a tool in this
conguration. Replace the handle immediately following
the task.
HANDLE
CIRCLIP

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
8
74.0 mm
(2.91”)
58.0 mm
(2.28”)
42.0 mm
(1.65”)
24.0 mm
(0.94”)
SMALL SAFETY BLOCK
3.9
STEP DIMENSIONS & SPREADING DISTANCES
JAW DIMENSIONS (WITHOUT STEPPED BLOCKS ATTACHED)
54.0 mm
(2.13”)
38 mm
(1.50”)
22.0 mm
(0.87”)
4.0 mm
(0.16”)
TOOL CLOSED
79.0 mm
(3.11”)
63.0 mm
(2.48”)
47.0 mm
(1.85”)
29.0 mm
(1.14”)
TOOL OPEN
JAW DIMENSIONS (WITH STEPPED BLOCKS ATTACHED)
57.0 mm
(2.24”)
76.0 mm
(2.99”)
TOOL CLOSED
82.0 mm
(3.23”)
101.0 mm
(3.98”)
TOOL OPEN
SAFETY BLOCK DIMENSIONS
96.0 mm
(3.78”)
76.0 mm
(2.99”)
LARGE SAFETY BLOCK

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
9
4.3
SERVICING
Replace missing worn or damaged parts. Use only
genuine Equalizer parts from approved distributors or
service centres. Equalizer parts have been engineered and
manufactured to be t-for-purpose.
Grease all moving parts by following the Lubrication
Procedure prior to usage, storage or transportation.
If topping up or replacing hydraulic oil as part of a service,
use only premium quality hydraulic oil of the grade 15 cSt.
4.4
LUBRICATION PROCEDURE
Apply grease following cleaning and servicing, prior to
usage, storage or transportation. Never assemble and
leave a tool without following the greasing procedure as
degradation or damage may occur.
Use only high pressure molybdenum disulphide grease.
Remove the jaws as per the dissassembly instructions.
Apply grease liberally to the following areas:
• the large at surface on the underside of the jaws
• the internal at surfaces in the square cut-out in the
jaws
4.5
STORAGE & TRANSPORTATION
Equalizer tools should be stored in a cool dry place. Tools
should always be cleaned, serviced and lubricated prior to
storage. Ensure that tools are stored in their designated
packing cases.
4.
TOOL MAINTENANCE
4.1
INSPECTION
A thorough inspection should be carried out prior to usage,
storage or transportation to ensure the completeness and
condition of the tool.
Inspection should include:
• visual inspection of the outer parts of the tool,
checking for obvious damage, degradation or missing
parts
• visual inspection of the wedge-tip (requiring tool
actuation or jaw removal). Damage to the wedge-tip
is indicative of tool over-load.
Cleaning and servicing should be undertaken as required
prior to the tool being used, stored or transported.
4.2
CLEANING
To lightly clean the tool, wipe gently with a damp cloth.
If more thorough cleaning is required (for example
following immersion in water) carry out the following
cleaning procedure:
• strip the tool down, observing the schematics in
section 8.
• clean the components using detergent, following the
manufacturer’s guidelines
• rinse the components to remove traces of detergent
• dry the components thoroughly
Inspect, service and lubricate the tool immediately after
the cleaning process.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
10
4.7
SUB-SEA USAGE
The Equalizer range of HP hydraulic hand pumps are tted
with a sealed-bladder type reservoir system that allows
for sub-sea operation.
The SWi5TE is actuated by means of single-acting
spring-return hydraulic cylinder and can be used sub-sea
providing the following actions are taken:
• The gauge and manifold are removed from the
Equalizer HP350S/D hydraulic hand-pump and the
coupler is tted directly to the pump outlet (tools in
this conguration can be requested from Equalizer).
• The tool is connected to the Equalizer HP350S/D
pump whilst still top-side.
• The pump release valve is fully opened and remains
open until the tool has descended to the working
depth. This will allow the pressure to equalise.
• The tool is actuated via the hand pump by a diver.
• Upon completion of works the release valve is left in
the fully-open position until the tool has ascended to
the surface.
• The tool and pump are stripped-down, cleaned and
lubricated immediately to minimise corrosion.
Please note that a SWi5TE tool cannot be operated from
top-side by use of a down-line. The return springs in the
hydraulic cylinders do not have sufcient force to close
the tool if used with a down-line from a top-side pump,
therefore the standard hydraulic tools will not function
correctly and may jam in place if used in this conguration.
4.6
OPERATING CONDITIONS
GREASE LIMITATIONS:
Minimum Temperature: -5 °C (23 °F)
Maximum Temperature: 40 °C (104 °F)
MECHANICAL TOOLS:
Minimum Jaw Contact Temperature: -30 °C (-22 °F)
Maximum Jaw Contact Temperature: 150 °C (302 °F)
HYDRAULIC TOOLS:
Minimum Jaw Contact Temperature: -30 °C (-22 °F)
Maximum Jaw Contact Temperature: 70 °C (158 °F)
4.6
LONG-TERM STORAGE -
MAINTENANCE PLAN
1. Rub components down with a dry cloth to remove
moiusture.
2. Coat EVERY surface and contact point with a
corrosion inhibitor. Where nexessary, coat inside
and outside of component e.g. VC10
3. Nuts and threads must also be coated with a
corrosion inhibitor.
4. Once surfaces have been coated, seal individual
components in clear plastic bags or clear vaceem
bags or clear shrink wrap.
NOTE: bags/shrink wrap must be clear for visibility.
Take care when using shink wrap that the tool is /
components are still easy to see.
5. Remove all or, where not vacuum sealed, as much
air from bags as possible.
6. Once bags have been closed and sealed DO NOT
re-open. Any visual inspections must be done with
closed and sealed bags. If bags are opened the
components will have to be dried, re-coated and re-
sealed in bags/shrink wrap.
7. Replace silica gel (100g) EVERY TIME the case is
opened.
NOTE: depending on moisture content of air, silica
gel should be changed weekly.
8. Visually inspect kits after 30-days and every 30-days
thereafter. Remember to replace silica gel before
closing case.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
11
5.2
SWi5TE TOOL FUNCTION
HYDRAULIC TOOL OPERATION
The SWi5TE Spreading Wedge uses a hydraulic cylinder to
advance the wedge and spread the jaws. The hydraulic
pressure is applied using an external hand pump, enabling
accurate control of the force applied.
HAND PUMP OPERATION
Consult the Instruction Manual for the Equalizer HP Hand-
Pump.
ACTUATING THE SWi5TE
Follow the SWi Spreading Wedge Tool Operation
instructions, using the following instructions to actuate
the SWi5TE tool in particular:
When the Hand-Pump release valve is closed, pumping
the Hand-Pump handle will advance the cylinder and
spread the jaws.
When using multiple tools, ensure that the spread of all
tools correspond to keep the spreading force balanced.
Equalizer manufactures a twin-port hand pump which can
be used to actuate two tools simultaneously.
RETRACTING THE SWi5TE
Opening the release valve will depressurise the cylinder
and cause it to retract under the force of its internal
spring. The handle does not need to be pumped to retract
the tool.
When using multiple tools, exercise caution while
retracting to keep the spreading force balanced as the
gap is closed.
AIR-LOCK RELIEF
If full pressure is not achieved an air-lock may be present
in the hydraulic system. The following procedure can be
executed to relieve any air-locks.
Connect the hand pump to the tool with the hydraulic
hose. Close the release valve on the pump, and prime the
pump until the hydraulic cylinder is fully extended and a
small pressure is achieved.
5.
SWi5TE
HYDRAULIC FLANGE
SPREADING WEDGE
The SWi5TE Spreading Wedge uses an external hydraulic
pump to drive the cylinder to advance the wedge and
spread the jaws.
5.1
SWi5TE TOOL CAPABILITIES
SPREADING FORCE
With 700 bar (10 000 psi) of hydraulic pressure applied,
the tool can apply 6.3 T (63 kN) spreading force on the
1st step, up to 7.7 T (77 kN) spreading force on the 4th
step.
SPREADING GAP (SEE SECTION 3.9)
Using only the 1st step, the tool can spread from 4.0 mm
to 29 mm (0.16” - 1.14”).
Using all 4 steps, but without the stepped blocks, the tool
can spread from 4 mm to 79 mm (0.16” - 3.1”).
Using both steps on the stepped blocks, the tool can
spread 56 mm – 101 mm (2.2” - 4”).

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
12
5.3
SWi5TE KIT CONTENTS
SINGLE KIT
Product Code: SWi5TE-S
1 x SWi5TE Flange Spreader Wedgehead
1 x 700 bar (10 000 psi) Hydraulic Cylinder
1 x Safety Block
1 x Lanyard
1 x Instruction Manual
1 x Plastic Carry Case + Foam Insert
580 mm x 340 mm x 180 mm (22.8” x 13.4” x 7.1”)
Gross kit Weight: 8.7 kg (19.1 lb)
Tool only weight: 5.2 kg (11.4 lb)
With the hand pump elevated above the level of the tool,
and the tool in an upright position, open the hand pump
release valve causing any air that is within the system to
be forced up through the pump and vented into the oil
reservoir.
Repeat this process three further times to ensure that
all air is removed from the system. The tool should now
reach full working pressure.
Disconnect the hand pump from the hydraulic hose,
grip the baseplate of the hand pump body in a vice with
the pump body vertical and the main handle at the top.
Remove the four nuts holding the main handle and lift off.
Grip the relling plug with pliers and extract it by pulling
and twisting simultaneously. Ensure the reservoir body
is held down when removing the relling plug as pulling
up on the reservoir body will release the bladder within,
and oil may spill out. Fill the reservoir to the top with a
premium quality hydraulic oil of the grade 15 cSt. Reinsert
the relling plug, wipe away any oil, and reassemble by
reversing the disassembly process.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
13
5.4
SWi5TE DIMENSIONS
TWIN KIT
Product Code: SWi5TE-T
2 x SWi5TE Flange Spreader Wedgeheads
2 x 700 bar (10 000 psi) Hydraulic Cylinders
2 x Sets of Standard Safety Blocks
2 x Lanyards
1 x Set of Instruction Manuals
1 x Plastic Carry Case + Foam Inserts
580 mm x 340 mm x 180 mm (22.8” x 13.4” x 7.1”)
Gross Kit Weight 14.4 kg (31.7 lb)
Tool only weight: 5.2 kg (11.4 lb)
STEPPED BLOCK KIT
Product Code: 1640016-01
2 x SWi5TE Step Block
2 x M6 CSK Hex Screw
2 x Retaining Washer
1 x SWi5TE Large Safety Block
2 x 4mm Allen Key
Gross Kit Weight 1.3 kg (2.9 lb)
TOOL DIMENSIONS
- CLOSED
4.0 mm
(0.16”)
295.5 mm
(11.64”)
245.5 mm
(9.67”)
50 mm
(1.97”)
162.9 mm
(6.41”)

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
14
6.
TROUBLESHOOTING
6.1
SWi5TE TROUBLESHOOTING
THE WEDGE IS ADVANCING BUT DOES NOT
REACH FULL PRESSURE
POSSIBLE CAUSE:
There is air in the hydraulic system.
RECOMMENDED ACTION:
Follow the Airlock Relief instructions.

OPERATOR INSTRUCTION MANUAL SWi5TE_Rev02_A5
SWi5TE FLANGE SPREADING WEDGE
15
8.
PARTS LISTS
& SERVICE KITS
7.
REGULATORY
INFORMATION
7.1
REGISTERED HEAD OFFICE
EQUALIZER INTERNATIONAL LTD.
Equalizer House
Claymore Drive
Aberdeen
Scotland
AB23 8GD
7.2
APPLICABLE PATENT NUMBERS
The following list of Patents are applicable to EQUALIZER
INTERNATIONAL LTD SWi5TE tools:
REGISTERED DESIGNS
• 002224980-0001
• 002224980-0002
• 002224980-0003
• 002224980-0004
• 084204
• 353180
• 256685
• ZL201330454407.8
• 93373
• D729603
• D168772
• 41538

2
3
2X
7
4X
8
4X
6
2X
11
4X
4
2X
1
5
2X
9
2X
17
2X
10
4X
19
2X
14
2X
13
16
18
12
15
ITEM NO. PART NO DESCRIPTION QTY
1 1640001-01 SWi5TE BODY 1
2
1640006-01 SWi5TE WEDGE COATING 1
3
1640002-01 SWi5TE JAW 2
4
1120003-01 SWi5TE LINK_FINISHED 2
5
1120007-01 SWi5TE PIN_FINISHED 2
6
1120008-01 SWi5TE PIN_FINISHED 2
7
1640007-01 SWi5TE JOINING PLATE 4
8
110006-01 M3 x 8 CSUNK SCREW 4
9
1640050-01 SWi5TE COVER PLATE 2
10
110007-01 M5 x 16 CSUNK SCREW 4
11
901301-01 EXTERNAL CIRCLIP 4
12
1640300-01 SWi5TE HANDLE ASSEMBLY 1
13
1640200-01 SSS050UK 5T CYLINDER 1
14
300401-01 M5 SCKT SET SCREW 2
15
1120017-01 EXTERNAL CIRCLIP - DIN 471 - 40 x 1.75 1
16
1640052-01 SWi5TE CYLINDER WRAP STICKER (LARGE) 1
17
1640053-01 SWi5TE COVER PLATE TRIANGLE STICKER 2
18
1640054-01 SWi5TE CYLINDER WRAP STICKER (SMALL) 1
19
1640204-01 SWi5TE WEDGE LOGO STICKER 2
SWi5TE PARTS LIST
1640000-01 REV 03
Page 16

5
2
11
3
9
6
1
8
7
2X
4
10
ITEM NO. Part No DESCRIPTION QTY
1 1640201-01 CYLINDER BODY 1
2
1640202-01 CYLINDER PISTON 1
3
1640203-01 CYLINDER ENDCAP 1
4
300901-01 COUPLER 1
5
KIT
1640213-01
CYLINDER WIPER SEAL
1
6
CYLINDER TENSION DIE SPRING 1
7
CYLINDER SPRING LOCK 2
8
CYLINDER M5x16 CAP SCREW 1
9
CYLINDER M5x12 CAP SCREW 1
10
CYLINDER O-RING 1
11
CYLINDER BACKUP RING 1
HYDRAULIC CYLINDER PARTS LIST
1640200-01 REV 01
Page 17

SWi5TE SAFETY BLOCK (SMALL)
1640015-01 REV 03
Page 18

SWi5TE LARGE SAFETY BLOCK ASSEMBLY
1640017-01 REV 03
Page 19

4
2
2X
1
2X
3
2X
5
2X
ITEM NO. PART NO DESCRIPTION QTY
1 1640011-01 SWi5TE STEP BLOCK 2
2
503703-01 M6 CSK HEX SCREW 2
3
830901-01 RETAINING WASHER 2
4
1640017-01 SWi5TE LARGE SAFETY BLOCK ASSEMBLY 1
5
060701-01 4mm ALLEN KEY 2
SWi5TE STEP BLOCK (PAIR) KIT
1640016-01 REV 03
Page 20