Erbauer ERB566CSW User manual
1500W 190mm Circular Saw ERB566CSW
ERB566CSW
Original Instructions
(Version 1.0)
1500W 190mm Circular Saw ERB566CSW
GUARANTEE
This product carries a 2 year guarantee. If your product develops a fault within this
- Fair wear and tear
- Misuse or abuse
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please con-
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This
product should give you reliable service but for your peace of mind this
power tool does carry a 2 year guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
GENERAL POWER TOOL SAFETY WARNINGS
Warning: Read all safety warnings and all instructions.
Save all warnings and instructions for future reference.
power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools.
will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
1500W 190mm Circular Saw ERB566CSW
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
or medication.
b. Use personal protective equipment. Always wear eye
protection.
safety shoes, hard hat, or hearing protection used for appropriate
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating part of the power tool
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool in
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving parts.
parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for
your application.
and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools.
power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are
f. Keep cutting tools sharp and clean.
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
result in a hazardous situation.
5. Service
using only identical replacement parts. This will ensure that
ADDITIONAL SAFETY RULES FOR YOUR CIRCULAR SAW
1. Always wear a dust mask, hearing protection and eye
protection.
1500W 190mm Circular Saw ERB566CSW
practicable.
electrical condition.
the rating plate.
saw.
upwards or at the side.
saw no load speed.
cable and pipes.
could be hot.
19. Do not use any abrasive wheels.
20. Use only blade diameter(s) in accordance with the markings.
SAFETY WARNINGS FOR ALL SAWS
a)
Danger: Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot
be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot
c) Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below
the workpiece.
d) Never hold piece being cut in your hands or across your
leg.
binding, or loss of control.
e) Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may contact
hidden wiring or its own cord.
the operator.
f) When ripping always use a rip fence or straight edge guide.
blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes.
of control.
h) Never use damaged or incorrect blade washers or bolt.
safety of operation.
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS
KICKBACK CAUSES AND RELATED WARNINGS
- K
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
- When the blade is pinched or bound tightly by the kerf closing
rapidly back toward the operator;
- I
at the back edge of the blade can dig into the top surface of the
toward the operator.
procedures or conditions and can be avoided by taking proper
1500W 190mm Circular Saw ERB566CSW
precautions as given below.
side of the blade, but not in line with the blade. Kickback could
controlled by the operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut for any reason,
c) When restarting a saw in the workpiece, centre the saw blade
in the kerf and check that saw teeth are not engaged into the
the workpiece as the saw is restarted.
kickback. Large panels tend to sag under their own weight.
line of cut and near the edge of the panel.
binding and kickback.
can cause kickback.
SAFETY INSTRUCTION FOR CIRCULAR SAW WITH INNER
PENDULUM GUARD
a) Check lower guard for proper closing before each use. Do
not operate the saw if lower guard does not move freely and
close instantly. Never clamp or tie the lower guard into the
open position.
be bent. Raise the lower guard with the retracting handle and
other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard
and the spring are not operating properly, they must be
serviced before use.
c) Lower guard may be retracted manually only for special cuts
such as “plunge cuts” and “compound cuts.” Raise lower
guard by retracting handle and as soon as blade enters
the material, the lower guard must be released. For all other
d) Always observe that the lower guard is covering the blade
An unprotected,
coasting blade will cause the saw to walk backwards, cutting
to stop after switch is released.
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
Construction workers are one of the at-risk groups within this because of the dust that they
Lung cancer
Silicosis
The risk of lung disease is linked to people who regularly breathe construction dust over a
used.
1500W 190mm Circular Saw ERB566CSW
2. Use a less powerful tool e.g. a block cutter instead of angle grinder.
Warning: Some dust particles created by power sanding, sawing, grinding, drill
and other construction jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm.
To
• Work in a well-ventilated area.
designed
VIBRATION
daily basis and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Cutting wood h,W
used with the current guidance on vibration.
Warning:
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
Warning:
working period on this tool.
Maintain this tool in accordance with these instructions and keep well lubricated
(where appropriate)
Health Surveillance
any vibration related diseases at an early stage, prevent disease progression and help
Double insulation
tool to be earthed.
Important note
with a two-core cable and plug.
1500W 190mm Circular Saw ERB566CSW
SYMBOLS
Warning
Double insulation
Wear ear protection
Wear eye protection
Wear safety gloves
Waste electrical products should not be disposed of with household waste.
or retailer for recycling advice.
18 2
3
21
22
12 20
7
18
19
4
5
6
9
11
10
13
17
14
16
15
1500W 190mm Circular Saw ERB566CSW
1. SAFETY ON/OFF SWITCH
2. FIXED GUARD
3. BASE PLATE
4. LOWER BLADE GUARD
5. LOWER GUARD LEVER
6. SAW BLADE
7. BASE PLATE BEVEL LOCK
8. LOCK-OFF BUTTON
9. SPINDLE LOCK BUTTON
10. DEPTH ADJUSTMENT LEVER
11. DEPTH SCALE
12. HEX KEY
13. DUST EXTRACTION OUTLET
14. INNER FLANGE
15. BLADE BOLT
16. OUTER FLANGE
17. SPINDLE
18. BEVEL SCALE
19. CUTTING GUIDE NOTCH
20. PARALLEL GUIDE
21. VACUUM ADAPTOR
22. PARALLEL GUIDE TIGHTEN SCREW
Rated voltage
Rated power
No-load speed
Protection class
90o
o
Machine weight
NOISE INFORMATION
A weighted sound pressure LpApA
A weighted sound power LwAWA
ACCESSORIES
Blade (Ø190xØ30x24T) 1pc
Parallel guide 1pc
Vacuum adapter for 35mm hose interface only 1pc
Hex key 6mm 1pc
TECHNICAL DATA
1500W 190mm Circular Saw ERB566CSW
OPERATING INSTRUCTIONS
Note:
instruction book carefully.
INTENDED USE:
crossways cutting of wood with straight cutting lines
the work piece.
1. DUST EXTRACTION OUTLET
2. SAFETY ON/OFF SWITCH
off switch.
3. HAND GRIP POSITION
when operating. The right and wrong ways to
4. FITTING AND CHANGING A SAW BLADE(See
Fig. 2-1, 2-2, 2-3)
the saw blade carefully to make sure that
no breakage or damage has occurred during
shipping.
Press the spindle lock button (9), and use the
clockwise and hold open using the lower blade
RIGHT
WRONG
12
15
9
14
Fig. 1-1
Fig. 1-2
Fig. 2-1
Fig. 2-2
Warning: Blade teeth are very sharp,
the saw blade. For best cutting results , please
quality you need.
5. DEPTH OF CUT ADJUSTMENT
depth which shown on scale (11) and push the
6. BASE PLATE
blade breakage (See Fig. 1-1)
7. BASE PLATE ANGLE ADJUSTMENT
8. PARALLEL GUIDE ADJUSTMENT
edge at a chosen distance. Slide the parallel guide
cutting distance and tighten screw to lock into
11
10
Fig. 2-3
Fig. 3-1
18
7
Fig. 4
Fig. 5
1500W 190mm Circular Saw ERB566CSW
cut to check the setting.
WORKING HINTS FOR YOUR CIRCULAR
SAW
usage at very low speeds. Always use a blade
of blade teeth increases. Always ensure that the
of the cut.The blade cuts on the upward stroke and
surface is a non-visible surface when your work is
MAINTENANCE
cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry
all working controls free of dust. Occasionally you
persons in order to avoid a hazard.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
Local Authority or retailer for recycling advice. For
24
4
Fig. 6
Fig. 7
Fig. 8-1
Fig. 8-2
PLUG REPLACEMENT
(UK & IRELAND ONLY)
instructions below.
IMPORTANT
BLUE =NEUTRAL
Brown = Live
proceed as follows. The wire which is coloured blue
Warning:
Never connect live or neutral wires to the earth
BS1363/A plug and the correct rated fuse.
Note:
engaging into a socket.
Connect
(neutral)
Outer sleeve
Cable grip
Other manuals for ERB566CSW
1
Table of contents
Other Erbauer Saw manuals
Erbauer
Erbauer ERB690CSW User manual
Erbauer
Erbauer EBJ860 User manual
Erbauer
Erbauer ERB800RL User manual
Erbauer
Erbauer ERB1590LA User manual
Erbauer
Erbauer ERB238MSW User manual
Erbauer
Erbauer ERB610MSW User manual
Erbauer
Erbauer ERF298MSW User manual
Erbauer
Erbauer ERB611MSW User manual
Erbauer
Erbauer EDD18-Li-2 User manual
Erbauer
Erbauer ERA568RSP User manual
Erbauer
Erbauer ECS1400 User manual
Erbauer
Erbauer ERB237MSW User manual
Erbauer
Erbauer EMIS216S User manual
Erbauer
Erbauer ERB1721A User manual
Erbauer
Erbauer ERB373RSP User manual
Erbauer
Erbauer ERB2502SE User manual
Erbauer
Erbauer ERB110SSW User manual
Erbauer
Erbauer ECS18-Li User manual
Erbauer
Erbauer ERI490CSW User manual
Erbauer
Erbauer 3663602796244 User manual
Popular Saw manuals by other brands
AEG
AEG BUS 18A Original instructions
Schneider Airsystems
Schneider Airsystems KS 9A - SYS Original operating manual
Diamond Products
Diamond Products CC1700 Parts list & operating manual
Stihl
Stihl TSA 230 instruction manual
Triton
Triton TTS 1400 Operating/safety instructions
Elektra Beckum
Elektra Beckum BKS 400 Assembly & operating instructions
