Ergo Desktop KANGAROO JUNIOR User manual

THE KANGAROO JUNIOR -ASSEMBLY INSTRUCTIONS
Ass EMBLY PARTS usT
A. (6) Black Screw Covers
B. (2) 1/ 4-20 x 2. 50 Hex Head Bolts
C. (1) 5/ 32 Allen Wrench
D. (2) Fender Washers
E. (2)
Acorn Nuts
F. (3) 1/ 4-20 x 7/8 BHCS
G. (2) Thick Black Washers
H. (1) 7/ 16 Wrench
I. (2) Locking Star Washers
Single Button Screw
I
I
I..
I
Lifting assembly
should be flat
against the base
when tight.
Step 1: Lay the Lifting Assembly on a solid surface with the back side up as shown. Notice the single Button Head
Bolt and the threads of the spring in the assembly union. DO NOT LOOSEN THE SINGLE BUTTON HEAD BOLT.
Now notice the (2) oversized holes in the base plate. The Single Button Head Screw and the Threads of the Spring will
go into these oversized holes.
Step
2: With the Base Plate over hanging the table about 2 inches, hold the Lifting Assembly above the Base Plate and
align the Single Button Bolt and the Spring Threads into the oversized holes.
Step
3: Insert and thread the (3) 1/ 4-20 x 7/ 8 BHCS through the Base Plate and into the Lifting Assembly. Once all
(3) bolts are threaded in, tighten securely with the 5/ 32 allen wrench . Lifting Assembly should be flat against the
Base. P. 1

THE KANGAROO JUNIOR -ASSEMBLY INSTRUCTIONS
II
STEP 4,5,6 STEP 7 STEP 8
Step 4: Loosen the main brake and the monitor brake and allow the lifting assemblies to extend completely.
Step
5: Re-tighten both brakes.
Step 6: Remove the single bolt and nut that holds the upper spring bracket in place.
Step
7: After removing the bolt and nut in step 6 it should look like this.
Step 8: Put l Locking Star Washer on one of the l / 4-20 x 2.5 Hex Head screws. Then slide the Hex Head screw
through the spring bracket and vertical rail as shown.
STEP 10 STEP 11 STEP 12 STEP 13
Step 9: Put l Locking Star Washer on the other l / 4-20 x 2.50 Hex Head Bolt and push it through the vertical rail so
the threads show on the front of the lifting assembly.
Step l 0:
Put l fender washer on each of the l / 4-20 x 2.50 Hex Head Bolts.
Step
11 : Lift the Main Work Surface and guide the bolts through the holes in the horizontal rail.
Step
12 : Put on Thick Black Washers and Acorn Nuts. Tighten with the 7/ 16 wrench.
Step l 3: Cut the zip tie holding the vertical assembly together.
P. 2

THE KANGAROO JUNIOR -ASSEMBLY INSTRUCTIONS
STEP 14
Step 14: Remove the (4) 1/ 4-20 x 1.0 hex head bolts and (4) washers from the bottom of the
Monitor Lifting Assembly.
STEP 1 5, 16
Step 1 5: Position the Monitor Shelf below the lifting assemble
and align the holes in the Monitor Shelf with the threaded holes in the
Monitor Lifting Assembly.
Step 16: Thread the (4) hex head bolts
into the threaded holes in the
Monitor Lifting Assembly to secure the Monitor shelf to the unit.
Tighten securely
with a 7/ 16 wrench.
P. 3

Push down heref
~----: l!""t!l!"'"!I~
optimal location for support leg
Maximum Monitor weight of 12 lbs
Any questions about The Kangaroo Junior
Contact us at info @ ergodesktop .com or 866-232-7988
How TO UsE THE JUNIOR
To raise the Junior, loosen the main brake (D) and
lift the main work surface on the sides (E & E) .
After reaching the desired height, tighten the
work surface brake. Loosen the monitor brake
(A)
and raise the monitor shelf (B) with one hand.
After reaching the desired height tighten the
monitor brake. Place the stabilization leg included
with your unit, between the work surface and
steel base plate.
To lower the Junior, remove the stabilization leg,
loosen the main brake
(D) and lean into the unit
using your upper body weight pushing down with
both hands
on the horizontal bar at the rear of
the main horizontal work surface (C & C) . After
the Work Surface is lowered, tighten the work
surface brake
(D) and loosen the monitor brake (A) .
Lower the
monitor shelf to the desired height
then tighten the
monitor brake.
A. Monitor Brake
B. Monitor Shelf
C. Work Surface Rail
D. Main Brake
E. Main
Work Surface
How TO ADJUST YouR JUNIOR TO
SUPPORT LAPTOP OR MONITOR
If you have selected the Monitor /Laptop selection when
ordering
your Kangaroo Junior, the Junior's monitor shelf
will
be preset at the Monitor height, please follow the in-
structions below to change the monitor shelf to support a
laptop.
l. Bring the unit into the standing position.
2. Tighten the monitor brake (A) , and remove the monitor
from the shelf.
3. Go to the back of the unit and loosen the bolt attached
to the top of the monitor spring by just l /2 a turn.
4. Loosen the
monitor brake and lift the monitor shelf to
the desired height.
5. Tighten the monitor brake, then tighten the bolt
attached to the monitor spring.

THE STABILIZATION LEG
Your adjustable height desk unit comes with an adjustable leg that
can be used to give you maximum stability when you are using "The
Kangaroo" in the standing position.
Raise The Kangaroo work surface to your desired standing height
and
tighten the work surface brake.
Place the adjustable leg under the work surface and loosen the adjust-
able leg brake. Only loosen the brake by a turn or two, to much and the
brake
will disengage from the slot.
Extend the adjustable leg until it engages the bottom of the work
surface and then tighten the adjustable leg brake.
The leg
is shipped with the extension section installed to give you
additional height adjustment. If this is too tall for your application,
simply unscrew the extension section.
0 Extension Selection
G screws into here
ALWAYS REMOVE LEG BRACE BEFORE
LOWERING THE WORK SURFACE.