Ergo Desktop The Hybrid Kangaroo User manual

The hybrid Kangaroo - aSSeMbLy inSTrUCTionS
Assembly Parts list
A. (10) Black Screw Covers
B. (2) 1/4-20 x 3.50
Hex Head Bolts
C. (1) 5/32 Allen Wrench
D. (2) Fender Washers
E. (2) Acorn Nuts
F. (3) 1/4-20 x 7/8 BHCS
G. (2) Thick Black Washers
H. (1) 7/16 Wrench
I. (2) Locking Star Washers
Step 1: Lay the lifting assembly on a solid surface with the back side up as shown. Notice the single Button Head
Bolt in the assembly union plate. DO NOT LOOSEN THE SINGLE BUTTON HEAD BOLT THAT IS NOTATED.
Step 2: Notice the (2) oversized holes in the Base Plate. The Single Button Head Bolt will go into the oversized hole
on the top right, while the other 3 holes should line up with the base. The center oversized hole is not used with this unit.
Step 3: With the Base Plate over hanging the table about 2 inches, hold the Lifting As-
sembly above the Base Plate and align the Single Button Bolt into the oversized hole.
Place one 1/4-20 x 7/8 BHCS{F} through the base plate to screw in the lifting assembly.
Step 4: Insert and thread the other (2) 1/4-20 x 7/8 BHCS{F} through the Base Plate
and into the Lifting Assembly. Once all (3) bolts are threaded in, tighten securely with
the 5/32 allen wrench{C}. Lifting Assembly should be at against the Base and all three
bolts should look like the picture above.
Step 1 Step 2 Step 3 Step 4
A
B
C
D
E
F
G
I
H
Threads of Spring
Single button
head screw
Oversized Holes
Lifting assembly
should be at against
the base plate
when tight
Fender
Washer
Locking Star
Washer
1/4-20 x 3.50
Hex Head Bolt
1/4-20 x 3.50
Hex Head Bolt
Locking Star
Washer
STEP
5,6,7
Step 5: Put (1) Locking Star Washer{I} on each of the 1/4 –20 x 3.50 Hex Head Bolts{B}.
Step 6: Insert the (2) 1/4-20 x 3.50 Hex Head Bolts{B} through the holes in the Vertical Rail.
Step 7: Put (1) Fender Washer{D} on each of the 1/4-20 x 3.50 Hex Head
Bolts{B} on the other side of the Vertical Rail.

The hybrid Kangaroo - aSSeMbLy inSTrUCTionS
Step 8: Lift the Work Surface up and
align the holes in the Horizontal Rail with
the (2) 1/4-20 x 3.50 Hex Head Bolts{B}.
Push the Work Surface onto the Hex
Head Bolts until the threads of the bolts
come through the Horizontal Rail.
Step 9: Put (1) Black
Washer{G} and (1) Acorn
Nut{E} on the end of each of
the Hex Head Bolts. Using the
7/16 wrench{H} tighten the
Acorn Nuts securely.
Step 10: Mount your monitor. Follow the mounting instructions below to mount your monitor.
STEP 8 STEP 9
Hidden
Fender
Washers
Fender
Washer
Step 10: Remove the (4) 1/4-
20 x 1.0 hex head bolts and (4)
washers from the bottom of the
Monitor Lifting Assembly.
STEP 10
STEP 11
Step 11: Position the
Laptop Shelf below the
lifting assembly and align
the holes in the Laptop
Shelf with the threaded
holes in the Monitor/lap-
top Lifting Assembly.
STEP 12
Step 12: Thread the
(4) hex head bolts
into the threaded
holes in the Lifting
Assembly to secure
the laptop shelf to
the unit. Tighten
securely with a 7/16
wrench.

The hybrid Kangaroo
The Hybrid Kangaroo is designed to hold (1) Mon-
itor on the VESA 75 x 75 or 100 x 100mm compat-
ible bracket, a laptop/monitor with a stand, on the
shelf and your keyboard and mouse on the main
work surface.
Your Hybrid Kangaroo is shipped in the down posi-
tion with the Main Brake tightened. The Hybrid
Kangaroo has (2) springs that assist in raising your
unit to the standing
position and works best when your monitors/lap-
top and keyboard are in place. This reduces the
amount of pressure needed to lower the unit.
Always push down with both hands on the hori-
zontal rear rail when lowering the work surface.
To raise the Hybrid, loosen the main brake(C) and lift the
main work surface on the sides(D & D). Once you have the
work surface at the required height tighten the main brake.
To lower the Hybrid, loosen the main brake(C) and lean into
the unit using your upper body weight pushing down with
both hands on the horizontal bar at the rear of the main
work surface (E & E).
Raise and lower the monitor rail by loosening the monitor
brake(A) and either lift up or push down on the horizontal
monitor rail(B). Once the monitors reach your desired level,
tighten the monitor brake.
how To USe The hybrid Kangaroo
A. Monitor Brake
B. Horizontal Monitor Rail
C. Main Brake
D. Main Work Surface
E. Work Surface
Horizontal Bar
D. Lift Here D. Lift Here
E. Push down hereE. Push down here
C. Main Brake
A. Monitor Brake
To move the mount horizontally closer or far-
ther apart, simply loosen the bolt attached to
the horizontal monitor rail (B) by a single turn
with a 5/32 allen wrench. Once you have
reached the desired position tighten the bolt.
B. Horizontal monitor
Rail
To move the shelf horizontally closer or farther apart,
simply remove the black caps with a at head screw driver
and loosen the bolts attached to the horizontal monitor
rail (B) by a 1/2 a turn with a 7/16 wrench. Once you have
reached the desired position re-tighten the bolts.

adjUST The STopping boLT
On the back side of your unit you will notice a small bolt located on the
lifting tower. This bolt is used as our work surface stopper. It is currently set
at 15”, the highest our unit should go. This setting is for a 6’2“ user on a 30”
high desk. If you are shorter than this, raise the unit to your desired height
and tighten the Main Brake. Adjust the stopping bolt by loosening the bolt
with one turn and drop the bolt down to reach the lower support, and
re-tighten the stopping bolt.
If you are a taller individual and need to raise the stopping bolt, please note
that the work surface can get up to 16 1/2 inches but you will be raising the
unit into the oil dampening zone of the spring. This makes it a little more
difcult to lower the unit into the seated position when raised to this
maximum point.
Our work surface should only be raised to your belt or navel line. This creates
a 90-110 degree angle in your elbows which is suggested in the standing po-
sition. This will also allow you to lower the unit with ease by simply
transferring your upper body weight into the back of the unit.
The STabiLizaTion Leg
Your adjustable height desk top unit comes with an adjustable leg that can be used
to give you maximum stability when you are using “The Kangaroo” in the standing
position.
Raise the Kangaroo work surface to your desired standing height and tighten the work
surface brake.
Place the adjustable leg under the work surface and loosen the adjustable leg brake.
Only loosen the brake by a turn or two, too much and the brake will disengage from
the slot.
Extend the adjustable leg until it engages the bottom of the work surface and then
tighten the adjustable leg brake.
The leg is shipped with the extension section installed to give you additional height
adjustment. If this is too tall for your application, simply unscrew the extension
selection.
always remember to remove the stabilization
leg before lowering your work surface
A Extension selection
B Screws into here