ErgoAV ERMSS1-01B User manual
Motion TV Mount with Locking Arm
Instruction Manual
<A>
English pages:
02-15
French pages:
16-29
Spanish pages:
30-43
Model: ERMSS1
-01
B
Thank You
for
Choosing
this
ErgoAV Product!
At
ErgoAV, we
want
to
add value
to
your AV experience by providing the highest
quality products and services in the industry.
If
you have any concerns
or
comments, please
contact
us.
ErgoAV Customer Care
phone(877)419-7832
email: [email protected]
website: .ergoav.com
address: 9501 Louisiana Ave
N,
#200, Brooklyn Park,
MN
55445
IMPORTANT SAFETY INFORMATION
A DANGER! Please carefully read all instructions before attempting installation.
If you
DO
NOT understand the instructions or have any concerns or questions,
please contact our Technical Support at (877)
419-
7832 or Customer Service at
A CAUTION: Use with products heavier than the maximum weights indicated
may result in instability causing possible injury.
•
DO
NOT use this product
for
any purpose that is NOT explicitly specified
in
this
manual.
DO
NOT exceed weight capacity. We are NOT liable
for
damage or injury
caused by improper mounting, incorrect assembly
or
inappropriate use.
• This product is designed
for
use
in
wood stud, solid concrete, and concrete
block walls -
DO
NOT install into drywall alone. Please note: When installing
into a recreational vehicle, please consult our Customer Service at
to
determine the correct screw depth
to
use
for
your
installation.
• The wall must be capable
of
supporting
four
times the weight
of
the TV and
mount combined.
• Use this mounting system only
for
its intended use
as
described
in
these
instructions.
DO
NOT use attachments NOT recommended by the manufacturer.
•
DO
NOT use outdoors.
• Route cords and cables properly
to
avoid mechanical damage.
•
SAVE
THESE INSTRUCTIONS.
Weight Restrictions
•
MAX
66
lbs/
29
kg
If your TV weighs more,
DO
NOT
use this product.
A WARNING
DO
NOT exceed the maximum weight indicated. This mounting
system is intended
for
use only within the maximum weights
indicated. Use with products heavier than the maximum weights
indicated may result in failure
of
the mount and its accessories,
causing damage and
or
injury.
Check the VESA Pattern of Your TV before the Installation
For
VESA
Patterns:
75mm x 75mm
~
3" x 3"
100mm x 100mm
~
3.9" x 3.9"
200mm x 100mm
~
7.9" x 3.9"
200mm x 200mm
~
7.9" x 7.9"
Minimum: 75mm x 75mm /
3"
x
3"
(W x
H)
Maximum: 200mm x 200mm / 7 7
/8"
x 7 7
/8"
(W x
H)
If
your
TV's
VESA
Pattern
is
smaller
than
75mm
x
75mm
or
greater
than
200mm
x200mm,
this
mount
is
NOT
COMPATIBLE
with
your
TV.
Please
contact
our
Technical
Support at
(877)
419-
7832
or
to find a compatible
mount.
02
Tools Needed (NOT Included)
Tape Measure Screwdriver Pencil Electric Drill Level
7/16"(11mm)
Socket Wrench
(Needed
for
wood stud installs)
~
OR
✓
5/Lm)
(Tools Needed for Solid Concrete,
Concrete Block and Brick Wall Installation)
5/1lrnm)
l
Stud Finder Awl Wood Drill
Bit
1 Concrete Drill
Bit
Hammer
Verify Your Wall Construction
AcAUTION
DO
NOT
install into
drywall alone. Wood Studs
(with Drywall)
Supplied
Parts
and
Hardware
Solid Concrete
Wall
If you are not sure
of
the wall construction,
please contact our
Technical Support
at (877)
419-7832
or
Customer Service at
A WARNING: This product contains small items that could
be
a choking hazard
if
swallowed.
Before starting assembly, verify
all
parts are included and undamaged.
Do
not use
damaged or defective parts. If you need replacement parts, please contact our
Technical Support at (877)
419-7832
or Customer Service at [email protected].
• PLEASE NOTE: NOT all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
"'o
® o( "
0 •
@ 0 0
10mm
13mm
0 0 G
TV
Mount
Iii
x1
Wrench
IIPJI
x1
03
Step 1 Unlock the
Arm
& Detach the Faceplate
1-1
Pull the strap down and stretch the arm away from the wall plate.
1-2
Slightly unscrew but NOT remove the Nut [S2] with the Wrench [02].
1-3
Remove the Bolt [S1] with the Wrench
[02]
or
a self-supplied screwdriver
and keep
it
for
use in step
4-2
on page 13.
S1
1-4
Separate the Faceplate
[01
BJ
from the Arm Assembly/Wall Plate [01A].
04
Supplied Parts
and
Hardware for Step 2
_
!~~~
---
~~
-~-
~~~~
-------------------
1
__
~
--
Spacers
[If_needed] -------------------------------------------
NOTE: The washers and spacers shown are actual size.
--------------------------------------------,-------------------------------------------------------------------------------------
® @ :
~
l~.1~~
4
~
l~~~~s
[B1]
x4
[B2]
x4
1 l=.J
M4/M5
M6/M8
m;J
TV
Bolts [Only one size
of
the bolt
fits
your TV]
NOTE: The bolts shown are actual size.
M4
@-I ©-ra--
M5
M4
x 12mm
[C1]
x4
M5 x 25mm
[DJ
x4
M4
x 30mm
[C2]
x4
----------------------------------
M6
M8
0--
M6 x 15mm
[E1]
x4
MB
x 15mm
[F1]
x4
M6 x 35mm
[E2]
x4
MB
x 35mm
[F2]
x4
Step 2 Secure the TV Faceplate to the TV
Only one bolt size
fits
your
TV.
M4
M5
M6
MB
JoR
JoRToR
0 0 0 0
NOTE: Please
DO
NOT over tighten the TV bolts
to
avoid damaging your
TV.
Bolt length: Verify adequate thread engagement with bolts
or
bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too
short will NOT hold the
TV.
-Too
long will damage the
TV.
05
Too Short Correct Too Long
Please Note: If spacers are required
for
your installation, a combination
of
different
spacers can be stacked
to
obtain a proper length. See examples
in
the image below. If you
have any difficulty understanding how
to
install the TV bolts
or
spacers, please contact our
Tech Support
at
(877)
419-
7832
or
Customer Service at [email protected].
=
=
=
=
=
=
=
=
=
B
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
E5
..
---
J \
§:
Curved TV
Bump
Cables
=·
Recessed Holes
See Option E
§:
: See Option B See Option C See Option D
E5
..
-
____
..
-
---------------------------------
=
§ Spacers
=
I
~se~
8
- -~l - - - -
_G_2_
---
~1c_+53.?
- -
_G_2i~~
- -
G1
+G2+G2 I
.....
"'
0 0
0 0
3 3
3 3
I I
--------------•
II I
I I
= r---------:
='
I
='
I
t UP
~
'
, '
' For VESA Patterns: '
75mm
x
75mm
~
3"
x
3"
1
00mm
x 1
00mm
~
3.9"
x
3.9"
200mm
x
100mm
~
7
.9"
x
3.9"
200mm
x
200mm
~
7.9"
x
7.9"
,
,,
_________________________________________________________
,,
06
A CAUTION: When attaching the Face-
plate
[01
BJ
to the back
of
the
TV,
ensure
the Pre-Assembled Nut [S2] is toward to
the top
of
the TV and is equally centered
on
the back
of
the
TV.
A PLEASE NOTE: The bolt hole
locations on your TV may vary
in
accor-
dance with the manufacturer's design
of
the
TV.
We
are only illustrating possible
locations
of
the bolt holes.
Option A (For Flat Back TV)
,,.
- - -
-~-
-------------
'1
I I
I I
I I
I I
I I
:
'f--l•I#IIC1
/D/E1
/~11
~~6
:
-----------.------
I
~~
@ B1/B21 :
I
'----------------------
Refer back
to
Spacer Instructions
on Page 6, If NEEDED
se
Option B (For Curved Back TV)
'
I
I
@
Phillips Screwdriver
(NOT Included)
The Spacers must be tall enough so
that
the curve on the back
of
the TV will NOT interfere with the mounting plate. Phillips Screwdriver
(NOT Included)
~
'
\~~
~
:
~"'o.,.
d> e
e,
..
e
.,
~
'----------------
Refer back
to
Spacer Instructions
on
Page 6,
If
NEEDe
g8
Option C (For TV with A "Bump")
(£)
-c::==a~,o
The spacers must be tall enough so there is no gap between Phillips Screwdriver
(NOT Included)
the faceplate and bump on the back
of
the TV.
,'
Li
'i
I I
I I
I I
I I
I I
:
C2/D/E2/F
I I /':::,.
~~
1
,~
B1/B2 1
~e,
I O I
~
.!,
'--------------------
-
Refer back
to
Spacer Instructions
on
Page 6,
If
NEEDe
g 8
®
..
.
~
:~~i'l
lg~
0
..
0
07
'
'I
I I
,,.----~-
u
I I
I I
I I
I I
:
'f--l•I#IC1
/D/E1 /F1 I
I I I
I I
t
~
B1
/B2
I
~
•
'----------
------------✓
Refer back
to
Spacer Instructions
on Page 6,
If
NEEDED
Option D (For TV with Cable Interference)
For cable interference, use the Spacers [G1] and [G2]
to
create extra space between the TV and TV faceplate.
-------
,
I
I --------, ,,-------
' I
----------
I I 'I
I
C2/D/E2/F2
, ______ _
______________
,
Refer back
to
Spacer Instructions
on
Page 6, If
NEEDe
g8
G1/G2
-------------------
Option E (For Recessed Holes)
,
The Spacer [G1] and [G2] needs
to
fill
in
the recessed holes on the
back
of
the TV so that the TV faceplate are as close
to
the TV as
possible.
-------------
,
I ' ,
I 'I
I
I
Phillips Screwdriver
(NOT Included)
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
(±)
<=•
==0c=::::J(0
Phillips Screwdriver
(NOT Included)
C2/D/E2/F2
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
B1/B2
I f \ l
,
,
_____________________
, ,
____________
_
-----------------
Refer back
to
Spacer Instructions
on
Page 6, If
NEEDe
g5
08
Supplied Part and Hardware
for
Step 3
-
x5
Completestep1
,nowner's
manual before mounting wall plate
0 0
·~~.·
to t .
~
Lag
Screw
1
/4"
X 1
3/4"
ml
x1
Wall Plate Template
AcAUTION!
!
Wall
fD
x5
Anchor
8 x 40mm
:~il~s
a~~~~-
i~i)o~~~n~~:te
~
B
~
Qg
~
g
2l
I]
them in drywall
or
wood
studs.
Step 3
Attach
the
Arm Assembly
/Wall
Plate
[01]
to
the
Wall
For wood stud installation, follow STEP 3A.
For concrete installation, follow STEP
38.
Step 3A Wood Stud Option
A WARNING:
DO
NOT use a drill
for
tightening the lag screws, only use a socket wrench.
A CAUTION:
If installation is in a
RV,
before drilling, ensure your wall thickness is greater than
2"
thick.
e
DO
NOT USE ANCHOR [A2] FOR THIS STEP.
• Ensure the wall plate is securely fastened
to
the wall
before continuing
to
the next step.
• Nominal wood stud size: common
2"
x
4"
(51
mm x 102mm)
• Stud center must be verified.
09
Wall
Anchor
3A-2
~
OR
I
I
*
I
I
I
I
t
rw,,
10
Use a stud finder (Not included)
to
locate wood studs
or
use
an
awl
(Not included)
to
verify the edges.
Mark the edge and center
loca-
tions.
Awl Stud Finder
(Not Included) (Not Included)
Position the Wall Plate Template
[03]
at
your desired height and
line up the holes with your stud
center line. Level the Wall Plate
Template
[03]
and mark the holes.
/-
Pencil Level
(NOT
Included) (Not Included)
Drill 3 pilot holes using a
5/32"
(4mm) diameter drill bit. Make
sure the depth
of
the holes is NOT
less than 1
3/
4"
(45mm) deep.
5/32"
(4mm)
1
3/
4"
(45mm) Electric Drill
(Nor Included)
:'
A NOTE:
DO
NOT use a drill
to
tighten the lag screws. Only use a socket wrench.
':
'---------------------------------------------------------------------✓
t
HEAVY! You may need
assistance with this step.
Install the Arm Assembly/Wall Plate
[01
A] using 3 Lag Screws [A1]. Tighten
the Lag Screws [A1] only until they are
pulled firmly against the Arm Assembly
/ Wall Plate
[01
A].
DO
NOT
over-tight-
en
the Lag Screws [A1].
Level
(Not Included)
~--
7/16"
(11mm)
Socket Wrench
(Not Included)
Step
38
Solid Concrete Wall Option
A.
WARNING:
DO NOT
use
a drill for tightening the lag screws! Only use a socket wrench.
• Avoid potential personal injury
or
property damage!
DO
NOT
over-tighten
the lag
Screws
[A
1]. Tighten the lag Screws
[A
1] only until they are pulled firmly against the wall
plate.
• Ensure the wall plate is securely fastened
to
the wall before
continuing
to
the next step.
• Mount the wall plate directly onto the concrete surface
without
any covering.
• The thickness
of
the concrete wall must exceed 5.5" (140 mm).
38-1
,/
Wall Thickness
':
/
"(
)'
_,_
,
__
-,
~5.5
140mm ;
,
__
------
--
--------
_.,
B:
□
D:
□ J
□
I
-
Wall
Anchor
Position the Wall Plate Template
[03]
at
your desired height, level
the Wall Plate Template
[03]
and
mark the pilot hole locations.
11
38-2
38-3
A2
~o
38-4
Drill 5 pilot holes using a
5/16"
(8mm) diameter drill bit. Make
sure the depth
of
the holes is
not less than
2"
(50mm) deep.
2"
(50mm)
Electric Drill
(Not Included)
Use the hammer
to
knock the
Anchors [A2] into the wall.
Be
sure the Anchors [A2] are seated
flush with the concrete surface.
:/
AWARNING:
DO
NOT use a drill
to
tighten :
I I
:the lag screws. Only use a socket wrench. :
,
____________________________________________
/
J
-----------
Install the Arm Assembly/Wall Plate
[01
A] using 5 Lag Screws [A1].
Tighten the Lag Screws [A1] only
until they are pulled firmly against
the Arm Assembly / Wall Plate
'
l
- ,
- I
~ ,
_
_!
t
.::
,
L-
-+--r--:,
I
[01
A].
DO
NOT over-tighten the
Lag Screws [A1].
HEAVY! You may need
assistance with this step. Level
(Not Included)
7/16"
(11mm)
Socket Wrench
(Not Included)
12
Step 4 Hang the TV onto the
Arm
Assembly/Wall Plate [01A]
~
HEAVY! You may need
assistance with this step.
Phillips
Screwdriver
(Not Included)
1111
Hang the TV on
to
the Arm Assembly / Wall Plate
[01
A], making sure the
Pre-Assembled Nut [S2] hangs inside the hook on the Arm Assembly / Wall Plate
[01
A].
O 0
0
1
11:1
o
□
:J
~
□
E~.j Install and tighten the Bolt [S1] which
was removed
in
step
1-3
to
secure the TV
to
the Arm Assembly/Wall Plate [01A].
13
ESI Tighten the Nut [S2].
Step 5 Adjustments
Tilt Adjustment
~==-==-==-==-=====-==
~~
-==~~~
1. Gently loosen the lever [T] by hand.
2.
Adjust the TV
to
your desired angle.
3.
Tighten the lever [T]
to
secure the
TV.
If needed, the TV can be levelled.
1.
Loosen the Bolt [S1] 1/ 4
of
a turn.
2.
Adjust the TV
to
be level.
3.
Retighten the Bolt [S1] firmly.
14
0
'======'?
0
*
(@
□
[J
Phillips
Screwdriver
(NOT Included)
Step 6 Storing your TV
M
■
To
store your TV against the wall, gently push the TV against the wall while
holding the strap down. Once the TV is against the wall, release strap and check
to
make sure the TV is being held in place by the latch.
t
W.JTo
release your TV
from
the stored position, gently push the TV against the
wall and pull down on the strap. Once the TV is away
from
the wall, release strap.
l
15
At
ErgoAV, we strive
to
provide the highest value products.
Speaker Stands
We want
to
support your purchase.
If you have questions, concerns,
or
feedback please let us know!
ErgoAV Customer Care
Phone(877)419-7832
Computer Monitor Mounts Tabletop TV Stand
9501 Louisiana Ave
N,
#200, Brooklyn Park,
MN
55445
www.ergoav.com
860-00098-00RevOO
Table of contents
Other ErgoAV Rack & Stand manuals
