ErgoAV ERTSL2-01B User manual

Model: ERTSL2-01B
Table Top TV Stand Instruction Manual
V1.0
THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest
quality products and services in the industry. If you have any concerns or
comments, please contact us.
ErgoAV Customer Care
Phone [phone] M-F 8am to 8pm CST
email: [email protected]
website: www.ergoav.com
adress: 9501 Louisiana Ave N, #200 Brooklyn Park, MN 55445
English pages: 02-16 French pages: 17-30 Spanish pages: 31-46

Before getting starting, let's make sure this mount is perfect for you!
IMPORTANT SAFETY INFORMATION
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
Please carefully read all instructions before attempting assembly. If you do
not understand the instructions or have any concerns or questions, please
contact our Technical Support line at [phone] or customer service at
[email protected].
99 lbs/
44.9 kg
1
Measure Your TV VESA Pattern:
Minimum: 100 x 100mm/4 x 4 in (WxH)
Maximum: 600 x 400mm/24 x 16 in (WxH)
1
W
H
Solid Concrete
or Concrete Block
DO NOT install into drywall alone.
Wood Studs
(with Drywall)
For safety strap
installations, you will
need to verify your
wall construction.
If this mount is NOT compatible, please contact our Technical Support line at
[phone] or customer service at [email protected] to find a compatible
mount.
If your TV is not between the minimum and
maximum measurements, do not use
this product.
If your TV weighs more than 99 lbs,
do not use this product.
02

Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
contact our Technical Support line at [phone] or customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
Tools Needed (Not lncluded)
AwlStud Finder
Tape Measure
Tape
Measure
Tape
Measure Pencil
Pencil
1/8 in (3mm)
Wood Drill Bit
5/16 in (8mm)
Concrete Drill Bit Hammer
Drill
Drill
Phillips
Screwdriver
Phillips
Screwdriver
Phillips
Screwdriver
For safety straps installation into concrete wall
For safety strap installatcon into wood table/furniture and wood stud applications
For TV stand assembly
(B1) x4
M4/M5
Washer
(B2) x4
M6/M8
Washer
(N) x2
TV Bracket
Supplied Parts and Hardware for Step 1
03

Step 1 Secure the TV Brackets [N] to TV
Select TV Bolts
Only one bolt size fits your TV.
(C1) x4
M4x12mm
Bolt
(C2) x4
M4x30mm
Bolt
(D1) x4
M6x15mm
Bolt
(D2) x4
M6x35mm
Bolt
(E1) x4
M8x15mm
Bolt
(E3) x4
M8x50mm
Bolt
Bolts and spacers are shown in actual size.
(F1) x8
L2.5mm
Spacer
(F2) x4
L10mm
Spacer
(F3) x4
L22mm
Spacer
(E2) x4
M8x35mm
Bolt
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
OR OR
Too Short Correct Too Long
M6 M8M4
04

Please Note: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install
the TV bolts or spacers, please contact our Technical Support line at [phone]
or customer service at [email protected].
N
When attaching the TV brackets to the
back of the TV, ensure the Up Arrows are
pointing to the top of the TV and are
equally centered on the back of the TV.
UP
TV Brackets have “three height locations”, which determines the height
position of your TV while attaching your TV on the stand in Step 5 on page 11.
You can choose the proper height.
Height Location #1
Height Location #3 Height Location #2
Bump
See Option C Cables See Option D Recessed Holes See Option E
Spacers
Curved TV
See Option B
Parts Needed if You Have a TV as Shown Below
F1+F1 F1+F2 F1+F3F1+F1+F2 F1+F1+F3 F2+F3 F1+F2+F3 F1+F1+F2+F3
05

Option A (For Flat Back TV )
B1/B2
C1/D1/E1
Option B (For Curved Back TV)
Option C (For TV with A “Bump”)
B1/B2
C2/D2/E2/E3
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 05, If needed
B1/B2
C2/D2/E2/E3
F1/F2/F3
Spacers must be large enough so TV bracekts are flush (NO GAP) on bump.
Refer back to Spacer Instructions
on Page 05, If needed
Spacers must be tall enough so that the curve on the back of the TV will not
interfere with the mounting plate.
F1/F2/F3F1/F2/F3
06

Option D (for TV with Cable Interference)
Option E (For Recessed Holes ）
For cable interference, use spacers [F1], [F2] and [F3]
to create extra space between the TV and TV brackets.
N
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 05, If needed
Refer back to Spacer Instructions
on Page 05, If needed
N
The spacer need to fill in the recessed holes on the basis of the TV so
that the TV brackets are as close to the TV as possible.
C2/D2/E2
B1/B2
F1/F2/F3
C2/D2/E2/E3
B1/B2
F1/F2/F3
F1/F2/F3F1/F2/F3 B1/B2
C2/D2/E2/E3
B1/B2
C2/D2/E2/E3
07

Step 2-1
(W) x6
Foot Pad
(R) x1
Reinforcement
Plate
(Y) x1
Trim Ring
Supplied Parts and Hardware for Step 2
This bolt is shown in
actual size.
(L) x3
M6x25mm
Bolt (P) x1
Support Pillar
(O) x1
Tempered
Glass Base
(V) x1
5/32 in (4mm)
Allen Key
Step 2 Assemble the Base
Connect the support pillar [P] to tempered glass base [O]
R
OYP
L
V
When assembling the support pillar
[P], ensure the side of the reinforcing
plate [R] with paper is facing the
glass base [O].
Note: Do Not
overtighten the
bolts [L].
O
V
LR
P
Table
Step 2-2
Place foot pads [W] to
the painted side of the
tempered glass
base [O] in the
corners W
Table
O
W
08

Distance from the hooks on the TV
Brackets to the bottom of the TV Recommended TV Mounting
Plate Location
20 1/8" to 23 1/2"
16 3/4" to 20 1/8"
Less Than 16 3/4"
Location #1
Location #2
Location #3
Note: Before attaching the TV Mounting
Plate to the pillar, measure the distance
from the upper hook on the TV Bracket
to the bottom of the TV. Then refer to
chart below for the recommended
mounting location. To add an additional
“2” of space between your TV and the
base, use the lower hooks located on
the TV Brackets. We always recommend
using the lowest possible attachment
location for the safest assembly.
(M) x1
TV Plate
(X) x2
Safety Strap
Supplied Parts and Hardware for Step 3
(V) x1
5/32 in (4mm)
Allen Key
(S) x4
M6x50mm
Bolt
This bolt is shown in actual size.
Step 3 Connect the TV Plate [M] to Support Pillar [P]
Mounting Location #1
Mounting Location #2
Mounting Location #3
(T) x4
M6x8mm
Bolt
(A) x1
Swivel Component
Location #1Location #1
Location #2Location #2
Location #3Location #3
09

Connect swivel component [A]
and safety straps [X] to support
pillar [P] using bolts [S] by the
allen key [V].
Connect TV plate [M] to
swivel component [A]
using bolts [T] by the
allen key [V].
(K) x2
Wire Clip
Supplied Part for Step 4
PX
AS
T
Note: Make sure the
bump of the TV plate
faces back side of
the TV stand.
You may need assistance with this step
A
M
10

Supplied Part for Step 5
(K1) x2
Safety Lock
Step 5-2
Step 5-1
Step 5-2
Step 5-1
OR
Step 4 Secure the Wire Clips [K] to Support Pillar [P]
K
Step 5 Attach TV to the TV Plate [M] and Manage the Wires
We recommend always having a second person to help during
this step. TV can be heavy and awkward to place on the stand.
It is best to have 2 people lift the TV from the sides so they
can see the attachment points.
Step 5-1 Hang the TV with
brackets to the TV plate.
Step 5-2 Push the bottom
of the TV to TV plate.
Smaller TV’s use the
upper hooks
Larger TV’s use the
lower hooks
Step 5-2
Step 5-1
Step 5-2
Step 5-1
Note: Attached TV Brackets
to the TV Mounting plate on
the lowest placement that
allows for TV to fit.
11

Supplied Hardware for Step 6A
x2
Z1
x4
Z2
x2
Z3
Step 5-3 Insert the safety locks [K1] into the upward facing hooks at the
midway to lower part of the TV bracket. Please note this is where the lower
part of the TV bracket meets the TV plate. Then tighten the bolts of the safety
lock [K1] until the bolts touch the TV plate.
Phillips Screwdriver
(Not lncluded)
Screw M5X25mmScrew M5X60mm M5 Washer(BK)
For wooden table furniture/wood stud installation.
K1
K1
Manage the wires
Note: Make sure the bolt is tighten
behind the TV mounting plate.
12

Secure The Safety Straps With TV Stand Against The Wall
For wood stud installation, follow STEP 6B.
For solid concrete or concrete block installation, follow
STEP 6C.
For wooden table furniture installation, follow STEP 6A.
X
Step 6A
For Wooden Table Furniture Installation
Pencil
(Not lncluded)
Note: For the safest possible installation, we recommend using the included safety
straps. By doing so, you will greatly reduce the possibility of a TV Tip Over.
● DO NOT USE ANCHOR [Z4] FOR THIS STEP!
Note: It is necessary to predrill a pilot hole to avoid splitting the
wood. Being careful not to damage your furniture.
Caution: The mounting surface must be thicker than 1 in (25mm).
It is reccommended that
the safety straps be
mounted at least 12” apart. Phillips Screwdriver
(Not lncluded)
Remoue ø1/8 in
Z2
X
1/8 in (3mm)
1in (25mm)
1 in (25mm)
1/8 in (3mm)
1 in (25mm)
1/8 in (3mm)
13

OR
Awl
(Not lncluded)
Stud Finder
(Not lncluded)
Pencil
(Not lncluded)
Step 6B
For Wooden Stud Installation
● DO NOT USE ANCHOR [Z4] FOR THIS STEP!
● Any material covering the wall must not exceed 5/8 in (16 mm).
● Nominal wood stud size: common 2 x 4 in (51 x 102 mm) minimum 1½
x 3½ in (38 x 89 mm).
● Stud center must be verified by using an awl or stud finder.
Note: Each strap must be
mounted to a separate stud.
Phillips Screwdriver
(Not lncluded)
Z1
2 1/2 in (60mm)
1/8 in (3mm)
1/8 in (3mm)
Wood Drill Bit
X
Z3
14

Step 6C For Solid Concrete or Concrete Block Installation
● Must use wall anchor [Z4] for this step.
● Any material covering the wall must not exceed 5/8 in (16 mm).
● Minimum solid concrete thickness: 203 mm (8 in).
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in).
● Never drill into the mortar between blocks.
Wall Anchor 8x50mm
Pencil
(Not lncluded)
Z4
5/16 in (8mm)
Concrete Drill Bit
Hammer
(Not lncluded)
Supplied Hardware for Step 6C
x2
Z1
x2
Z3
x2
Z4
Screw M5X60mm M5 Washer(BK)
Phillips Screwdriver
(Not lncluded)
Z1
Z3
12 in
(305mm)
2 9/16 in (65mm)
5/16 in (8mm)
15

Step 7 Swivel Adjustment
If necessary, the TV plate or TV can be swivelled manually.
16

Avant de commencer, vérifions que ce support est parfait pour vous!
CONSIGNES DE SECURITE IMPORTANTES
Attention: évitez les potentiels dommages corporels et aux biens!
• Ne pas utilizer ce produit dans le cas où cet instruction n’a pas indiqué. Ne
pas dépasser le poids limité. Nous ne sommes pas responsables des
dommages causés par le montage incorrect ou l’utilisation inappropriée.
• Veuillez bien lire tous les instructions avant du montage. Si vous ne
comprenez pas les instructions ou avez des questions, veuillez contacter notre
ligne d'assistance technique au [phone] ou notre service clientèle à
[email protected].
99 lbs/
44.9 kg
1
Mesurez le modèle VESA de votre téléviseur:
Minimum: 100 x 100mm/4 x 4 pouce (LxH)
Maximum: 600 x 400mm/24 x 16 pouce (LxH)
1
L
H
Béton massif ou
bloc de béton
NE PAS installer dans une cloison sèche seule.
Montants en bois
(avec cloison sèche)
Pour les installations
de sangles de sécurité,
vous devrez vérifier la
construction de votre
mur.
Si ce support TV n'est PAS compatible, veuillez contacter notre ligne d'assistance
technique au [phone] ou notre service clientèle à l'adresse
[email protected] pour trouver un support compatible.
Si votre téléviseur ne se situe pas entre les
mesures minimum et maximum, n'utilisez
pas ce produit.
Si votre téléviseur pèse plus de 99 lb,
n'utilisez pas ce produit.
17

Pièces et matériel fournis
Avertissement: Ce produit contient des petits objets susceptibles de présenter un
risque d'étouffement en cas d'ingestion.
Avant de commencer l'assemblage, vérifiez que toutes les pièces sont incluses et en
bon état. N'utilisez pas de pièces endommagées ou défectueuses. Si vous avez besoin
de pièces de rechange, veuillez contacter notre ligne d'assistance technique au
[phone] ou le service clientèle à l'adresse [email protected] pour trouver
un support compatible.
• Veuillez noter: le matériel inclus dans cet ensemble ne sera pas utilisé en totalité.
Outils nécessaires (non inclus)
Mètre ruban
Mètre
ruban
5/16 pouce (8mm)
Foret à béton Marteau-piqueur
Tournevis
cruciform
Ailette
Détecteur de
goujons
Mètre
ruban Crayon 1/8 pouce (3mm) Mèche à bois
Foreuse Tournevis
cruciform
Tournevis
cruciform
Pour l'installation de sangles de sécurité dans un mur en béton
Pour l'installation d'une sangle de sécurité dans les tables/meubles en bois et les
montants en bois.
Pour le montage du support TV
Pièces et matériel fournis pour l'étape 1
Crayon Foreuse
(B1) x4
M4/M5
Rondelle
(B2) x4
M6/M8
Rondelle
(N) x2
Support télé
18

Étape 1 Fixez les Plaque TV [N] sur le TV
Sélectionnez les Boulons de TV
Une seule taille de boulon convient à votre TV.
La taille réelle des boulons et des entretoises est indiquée.
Longueur de la vis: vérifiez que le filetage est correctement engagé avec les boulons
ou la combinaison vis/entretoises. Nous recommandons un engagement du filetage
sur au moins 5 tours.
- Trop court, le TV ne sera pas maintenu.
- Trop long, le TV sera endommagé.
Trop court Correct Trop long
(C1) x4
M4x12mm
Boulon
(C2) x4
M4x30mm
Boulon
(D1) x4
M6x15mm
Boulon
(D2) x4
M6x35mm
Boulon
(E1) x4
M8x15mm
Boulon
(E3) x4
M8x50mm
Boulon
(F1) x8
L2.5mm
Entretoises
(F2) x4
L10mm
Entretoises
(F3) x4
L22mm
Entretoises
(E2) x4
M8x35mm
Boulon
OU OU
M6 M8M4
19

Veuillez noter: lors de l'utilisation des entretoises, il est important de noter qu'elles
peuvent être utilisées sur plusieurs couches (c'est-à-dire empilées). Si vous rencontrez
des difficultés pour comprendre comment installer les boulons ou les entretoises du TV,
veuillez contacter notre service d'assistance technique au [phone] ou notre
service clientèle à l'adresse [email protected].
N
Lorsque vous fixez les supports TV à
l'arrière du téléviseur, assurez-vous que
les flèches vers le haut sont dirigées vers
le haut du téléviseur et qu'elles sont
également centrées sur l'arrière du
téléviseur.
Élever
Les supports TV ont "trois emplacements de hauteur", ce qui détermine la
position en hauteur de votre téléviseur lorsque vous la fixez sur le support à
l'étape 5 de la page 26.
Vous pouvez choisir la bonne hauteur.
Hauteur Emplacement #1
Hauteur Emplacement #3 Hauteur Emplacement #2
Bosse Voir
option C Câbles Voir Option D Trous encastrés Voir Option E
Entretoises
TV incurvée
Voir option B
Les pièces nécessaires si vous avez un TV tel qu'indiqué ci-après
F1+F1 F1+F2 F1+F3F1+F1+F2 F1+F1+F3 F2+F3 F1+F2+F3 F1+F1+F2+F3
20