ErgoAV ERTSL1-01B User manual

THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest
quality products and services in the industry. If you have any concerns or
comments, please contact us.
ErgoAV Customer Care
Phone [phone] M-F 8am to 8pm CST
email: [email protected]
website: www.ergoav.com
adress: 9501 Louisiana Ave N, #200 Brooklyn Park, MN 55445
Model: ERTSL1-01B
Table Top TV Stand Instruction Manual
V1.0
English pages: 02-15 French pages: 16-29 Spanish pages: 30-43

For safety strap
installations you will
need to verify your wall
construction
Before getting starting, let's make sure this mount is perfect for you!
IMPORTANT SAFETY INFORMATION
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
Please carefully read all instructions before attempting assembly. If you do
not understand the instructions or have any concerns or questions, please
contact our Technical Support line at [phone] or customer service at
[email protected].
If your TV weighs more than 99 lbs,
Do not use this product. 99lbs/
44.9kg
Measure Your TV VESA Pattern:
Minimum: 100x100mm/4x4 in (WxH）
Maximum: 600x400mm/23.6x15.7 in (WxH）
1
W
H
Solid Concrete
or Concrete Block
DO NOT install into drywall alone.
Wood Studs
(with Drywall)
If this mount is NOT compatible, please contact our Technical Support line at
[phone] or customer service at [email protected] to find a compatible
mount.
If your TV is not between the minimum
and maximum measurements, do not
use this product.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

(B1) x4
M4/M5
Washer
(B2) x4
M6/M8
Washer
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
contact our Technical Support line at [phone] or customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
Tools Needed (Not lncluded)
AwlStud Finder
Tape Measure
Tape
Measure
Tape
Measure Pencil
Pencil
1/8 in (3mm)
Wood Drill Bit
5/16 in (8mm)
Concrete Drill Bit Hammer
Drill
Drill
Phillips
Screwdriver
Phillips
Screwdriver
Phillips
Screwdriver
For safety straps installation into concrete wall
For safety strap installatcon into wood table/furniture and wood stud applications
For TV Stand assembly
(N) x2
TV Bracket
Supplied Parts and Hardware for Step 1
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Step 1 Secure the TV Brackets [N] to the TV
Select TV Bolts
Only one bolt size fits your TV.
(C2) x4
M4x30mm
Bolt
(C1) x4
M4x12mm
Bolt
(D1) x4
M6x15mm
Bolt
(D2) x4
M6x35mm
Bolt
(E1) x4
M8x15mm
Bolt
(E2) x4
M8x35mm
Bolt
(E3) x4
M8x50mm
Bolt
(F1) x8
L2.5mm
Spacer
(F2) x4
L10mm
Spacer
(F3) x4
L22mm
Spacer
Bolts and Spacers are shown in actual size.
OR OR
M6 M8M4
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

N
When attaching the TV Brackets to the
back of the TV, ensure the Up Arrows are
pointing to the top of the TV and are
equally centered on the back of the TV.
UP
Please Note: When using the spacers it is important to note that they can be used in
multi-layers (meaning stacked). If you have any difficulty understanding how to install
the TV bolts or spacers, please contact our Technical Support line at [phone]
or customer service at [email protected].
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Too Short Correct Too Long
Bump
See Option C Cables See Option D Recessed Holes See Option E
Spacers
Parts Needed if You Have a TV as Shown Below
F1+F1 F1+F2 F1+F3F1+F1+F2 F1+F1+F3 F2+F3 F1+F2+F3 F1+F1+F2+F3
Curved TV
See Option B
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Phillips Screwdriver
(Not lncluded)
Phillips Screwdriver
(Not lncluded)
B1/B2
C2/D2/E2/E3
F1/F2/F3
Refer back to Spacer Instructions
on Page 5, If NEEDED
Option A (For Flat Back TV )
B1/B2
C1/D1/E1
Height Location #1 Height Location #2 Height Location #3
TV Brackets have “three height locations”, which determines the height
position of your TV while attaching your TV on the stand in Step 5 on page 12.
You can choose the proper height.
Option B (For Curved Back TV)
Spacers must be tall enough so that the curve on the back
of the TV will not interfere with the mounting plate.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

N
F1/F2/F3
C2/D2/E2/E3
B1/B2
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 5, If NEEDED
Phillips Screwdriver
(Not lncluded)
Refer back to Spacer Instructions
on Page 5, If NEEDED
B1/B2
C2/D2/E2/E3
F1/F2/F3
Option C (For TV with A “Bump”)
Spacers must be large enough so TV bracekts are
flush (NO GAP) on bump.
Option D (for TV with Cable Interference)
For cable interference, use spacers [F1], [F2] and [F3] to
create extra space between the TV and TV brackets.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

B1/B2
N
F1/F2/F3
C2/D2/E2/E3
Step 2-1
(W) x6
Foot Pad
(R) x1
Reinforcement
Plate
(Y) x1
Trim Ring
This bolt is shown in
actual size.
(L) x3
M6x25mm Bolt (P) x1
Support Pillar
(O) x1
Tempered
Glass Base
(V) x1
5/32 in (4mm)
Allen Key
Place foot pads [W] to the painted side of the tempered glass
base [O] in the corners.
Step 2 Assemble the Base
O
W
Refer back to Spacer Instructions
on Page 5, If NEEDED
Phillips Screwdriver
(Not lncluded)
Supplied Parts and Hardware for Step 2
Option E (For Recessed Holes ）
The spacer need to fill in the recessed holes on the basis
of the TV so that the TV brackets are as close to the TV
as possible.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

(M) x1
TV Plate
(Q) x4
M6 Nut
(T) x4
D6.5 Washer
(X) x2
Safety Strap
Supplied Parts and Hardware for Step 3
(V) x1
5/32 in (4mm)
Allen Key
(V) x1
3/8 in (10mm)
Wrench
This bolt is shown in actual size.
Step 2-2 Connect the support pillar [P] to tempered glass base [O]
When assembling the pillar, ensure the
side of the reinforcing plate [R] with
paper is facing the glass base [O].
Do Not overtighten the bolts [L].
L
Y
P
P
L
V
V
R
R
O
OTable
(S) x4
M6x50mm Bolt
W
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Location #1
Location #2
Location #3
Connect TV plate [M] and safety
straps [X] to support pillar [P] using
bolts [S], washers [T] and nuts [Q].
Step 3 Connect the TV Plate [M] to Support Pillar [P]
Mounting Location #1
Mounting Location #2
Mounting Location #3
Note: Before attaching the TV Mounting
Plate to the pillar, measure the distance
from the upper hook on the TV Bracket
to the bottom of the TV. Then refer to
chart below for the recommended
mounting location. To add an additional
2” of space between your TV and the
base, use the lower hooks located on
the TV Brackets. We always recom-
mend using the lowest possible attach-
ment location for the safest assembly.
Distance from the hooks on the TV
Brackets to the bottom of the TV Recommended TV Mounting
Plate Location
20 1/8" to 23 1/2"
16 3/4" to 20 1/8"
Less Than 16 3/4"
Location #1
Location #2
Location #3
M
S
V
V
Q
T
X
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Step 5 Attach TV to the TV Plate [M] and Manage the Wires
Supplied Part and Hardware for Step 5-3
(K1) x2
Safety Lock
We recommend always having a second person to help during
this step. TV can be heavy and awkward to place on the stand.
It is best to have 2 people lift the TV from the sides so they
can see the attachment points.
Step 5-1 Hang the TV with brackets to the TV plate.
Step 5-2 Push the bottom of the TV to TV plate.
(K) x2
Wire Clip
Step 4 Secure the Wire Clips [K] to Support Pillar [P]
K
Supplied Part for Step 4
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Manage the wires
Step 5-3
Insert the safety locks [K1] into the upward facing hooks at the
midway to lower part of the TV bracket. Please note this is where the lower
part of the TV bracket meets the TV plate. Then tighten the bolts of the safety
lock [K1] until the bolts touch the TV plate.
Note: Attached TV Brackets to the TV Mounting plate on the lowest
placement that allows for TV to fit.
OR
Smaller TV’s use the upper hooks Larger TV’s use the lower hooks
Note: Make sure the bolt is tighten
behind the TV mounting plate.
Phillips Screwdriver
(Not lncluded)
Step 5-1
Step 5-2
Step 5-1
Step 5-2
K1
K1
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Secure The Safety Straps With TV Stand Against The Wall
For wood stud installation, follow STEP 6B
For solid concrete or concrete blocy installation, follow
STEP 6C
For wooden table furniture installation, follow STEP 6A
Note: For the safest possible installation, we recommend using the included safety
straps. By doing so, you will greatly reduce the possibility of a TV Tip Over.
X
Step 6A
For Wooden Table furniture Installation
Pencil
(Not lncluded) 1/8 in (3mm)
Z2
● DO NOT USE ANCHOR [Z4] FOR THIS STEP!
X
Note: It is necessary to predrill a pilot hole to avoid splitting the
wood. Being careful not to damage your furniture.
Caution: The mounting surface must be thicker than 1 in. (25mm).
It is reccommended that
the safety straps be
mounted at least 12” apart. Phillips Screwdriver
(Not lncluded)
1in (25mm)
1/8 in (3mm)
Supplied Hardware for Step 6A
x2
Z1
x4
Z2
x2
Z3
Screw M5X25mmScrew M5X60mm M5 Washer(BK)
For wooden table furniture/wood stud installation.
1 in (25mm)
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

OR
Awl
(Not lncluded)
Stud Finder
(Not lncluded)
Pencil
(Not lncluded)
Step 6B
For Wooden Stud Installation
● DO NOT USE ANCHOR [Z4] FOR THIS STEP!
● Any material covering the wall must not exceed 5/8 in (16 mm)
● Nominal wood stud size: common 2 x 4 in (51 x 102 mm) minimum 1½
x 3½ in (38 x 89 mm)
● Stud center must be verified by using an awl or stod finder
Note: Each strap must be
mounted to a separate stud. Phillips Screwdriver
(Not lncluded)
Z1
2 1/2 in (60mm)
1/8 in (3mm)
1/8 in (3mm)
Wood Drill Bit
X
Z3
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Step 6C For Solid Concrete or Concrete Block Installation
● Most with must weth must use wall anchor [Z4] for this step.
● Any material covering the wall must not exceed 5/8 in (16 mm).
● Minimum solid concrete thickness: 203 mm (8 in).
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in).
● Never drill into the mortar between blocks.
Wall Anchor 8x50mm
Pencil
(Not lncluded)
Z4
5/16 in (8mm)
Concrete Drill Bit
Hammer
(Not lncluded)
Supplied Hardware for Step 6C
x2
Z1
x2
Z3
x2
Z4
Screw M5X60mm M5 Washer(BK)
Phillips Screwdriver
(Not lncluded)
Z1
Z3
12 in (305mm)
2 9/16 in (65mm)
5/16 in (8mm)
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Avant de commencer, vérifions que ce support est parfait pour vous!
CONSIGNES DE SECURITE IMPORTANTES
ATTENTION : Évitez risques de blessures et de dommages matériels!
N'utilisez pas ce produit à des fins qui ne sont pas explicitement spécifiées
dans ce manuel. Ne dépassez pas la capacité de charge. Nous ne sommes
pas responsables des dommages ou blessures causés par un montage
incorrect, un assemblage incorrect ou une utilisation inappropriée.
Veuillez lire attentivement toutes les instructions avant de procéder à
l'assemblage. Si les instructions ne vous semblent pas claires ou si vous avez
des questions, veuillez contacter notre service d'assistance technique au
[phone] ou notre service clientèle à l'adresse [email protected].
99lbs/
44.9kg
1
W
H
Mesurez le modèle VESA de votre téléviseur :
Minimum : 100x100mm/4x4 pouce (LxH)
Maximum : 600x400mm/23,7x15,7 pouce
(LxH)
Béton massif ou
bloc de béton
NE PAS installer dans une cloison sèche seule
Montants en bois
(avec cloison sèche)
Pour les installations de
sangles de sécurité, vous
devrez vérifier la
construction de votre mur.
Si ce support n'est PAS compatible, veuillez contacter notre ligne d'assistance tech-
nique au [phone] ou notre service clientèle à l'adresse [email protected]
pour trouver un support compatible.
Si votre téléviseur ne se situe pas entre les
mesures minimum et maximum, n'utilisez
pas ce produit.
Si le poids de votre TV est supérieur à
99 lbs, n'utilisez pas ce produit.
L
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Pièces et matériel fournis
AVERTISSEMENT: Ce produit contient des petits objets suscepti-
bles de présenter un risque d'étouffement en cas d'ingestion.
Avant de commencer l'assemblage, vérifiez que toutes les pièces sont inclus-
es et en bon état. Les pièces endommagées ou défectueuses ne doivent pas
être utilisées. Si vous avez besoin de pièces de rechange, veuillez contacter
notre service d'assistance technique au [phone] ou notre service
clientèle à l’adresse [email protected].
Veuillez noter: le matériel inclus dans cet ensemble ne sera pas utilisé
en totalité.
poinçon
Détecteur de
montants
Ruban à mesurer
Ruban à
mesurer
Ruban à
mesurer crayon
crayon
mèche à bois de
3 mm (1/8 pouce)
Foret à béton de
8 mm (5/16 pouce) marteau
perceuse
Perçoir
tournevis
Phillips
tournevis
Phillips
tournevis
Phillips
Pour l'installation de sangles de sécurité dans un mur en béton
Pour l'installation d'une sangle de sécurité dans les tables/meubles en bois et
les montants en bois.
Pour le montage du meuble TV
(B1) x4
M4/M5
rondelle
(B2) x4
M6/M8
rondelle
Outils nécessaires (non inclus)
(N) x2
Support TV
Pièces et matériel fournis pour l'étape 1
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

Sélectionnez les vis pour le téléviseur.
Une seule taille de vis convient à votre téléviseur.
Étape 1 Fixez les supports du téléviseur [N] sur le téléviseur
(C2) x4
M4x30mm
boulon
(C1) x4
M4x12mm
boulon
(D1) x4
M6x15mm
boulon
(D2) x4
M6x35mm
boulon
(E1) x4
M8x15mm
boulon
(E2) x4
M8x35mm
boulon
(E3) x4
M8x50mm
boulon
(F1) x8
L2.5mm
Entretoise
(F2) x4
L10mm
Entretoise
(F3) x4
L22mm
Entretoise
La taille réelle des boulons et des entretoises est indiquée.
OÙ OÙ
M6 M8M4
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

N
Élever
Veuillez noter: lors de l'utilisation des entretoises, il est important de noter
qu'elles peuvent être utilisées sur plusieurs couches (c'est-à-dire empilées).
Si vous rencontrez des difficultés pour comprendre comment installer les
boulons ou les entretoises du téléviseur, veuillez contacter notre service
d'assistance technique au [phone] ou notre service clientèle à
l'adresse [email protected]èces nécessaires si vous avez un téléviseur
comme indiqué ci-dessous.
Longueur de la vis: Vérifiez que le filetage est correctement engagé avec
les vis ou la combinaison vis/entretoises. Nous recommandons un engage-
ment du filetage sur au moins 5 tours.
- Trop court, le téléviseur ne sera pas maintenu.
- Trop long, le téléviseur sera endommagé.
Trop court correct trop long
Bosse Voir
option C Câbles Voir Option D Trous encastrés Voir Option E
Entretoise
Les pièces nécessaires si vous avez un téléviseur tel qu'indiqué ci-après
F1+F1 F1+F2 F1+F3F1+F1+F2 F1+F1+F3 F2+F3 F1+F2+F3 F1+F1+F2+F3
TV incurvée Voir
option B
Lorsque vous fixez les supports TV à
l'arrière du téléviseur, assurez-vous que
les flèches vers le haut sont dirigées vers
le haut du téléviseur et qu'elles sont
également centrées sur l'arrière du
téléviseur.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43

tournevis Phillips
(non inclus)
B1/B2
C2/D2/E2/E3
F1/F2/F3
Option A (pour les téléviseurs à dos plat)
B1/B2
C1/D1/E1
Hauteur Emplacement #1 Hauteur Emplacement #2
Hauteur Emplacement #3
Les supports de télévision ont «deux emplacements de hauteur», ce qui
détermine la position en hauteur de votre télévision lorsque vous la fixez sur le
support à l'étape 5 de la page 24.
Vous pouvez choisir la bonne hauteur.
Option B (pour les téléviseurs à dos incurvé)
La hauteur des entretoises doit être suffisante pour éviter que la courbe à
l'arrière du téléviseur n'interfère avec la plaque de montage.
Reportez-vous aux instructions d'espacement
de la page 18, si nécessaire.
02 03 04 05 06 07 08 09 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39 40 41 42 43