ERGOFF K257003 User manual

5
3 1 4 1
1
1 2 2 1
5
1
3
2
4
11
11
A
F
A
Ax4
F
4x4
Type A: 2X580mm Type B: 1X580mm,1X890mm Type C: 2X890mm
F
A
F
A
AA
222
TYPE A TYPE B
TYPE C
Installation guide
125KG
600-1250mm
1100-1900mm
3
Technical data
Column Stage
Max. Weight Capacity
Height Range
Width Range
2x580mm
2x700mm
Side Brackets
Specification
Feet Specification
100KG
600-1250mm
1100-1900mm
3
Technical data
Column Stage
Max. Weight Capacity
Height Range
Width Range
2x890mm
2x900mm
Side Brackets
Specification
Feet Specification
125KG
600-1250mm
1100-1900mm
3
Technical data
Column Stage
Max. Weight Capacity
Height Range
Width Range
1x580mm, 1x890mm
1x700mm, 1x900mm
Side Brackets
Specification
Feet Specification
A
1
C
D
4
B
E
4
F
16
12
8
Accessory list
Attention: The drawings below are for guidance only and they may differ
slightly from the product and fittings received. Please contact our customer
service department if you have any queries.
M6
St4.2
M6
M6
M6
Allen Key
4x4mm
No. Image Spec Qty
Component list
Freely combinable parts
No. Part Qty No. Part Qty
No. Part Qty No. Part Qty
No. Part Qty
Feet 1
Lifting Column
Side Bracket 1
Supporting Beam
(control box included)
Cable
Management Cover Handset
Power Plug
Feet 2
Side Bracket 2
Installation diagram
STEP 1 Connect Side Brackets with Supporting Beam
Select side brackets according to needs.
Connect the side brackets and the support beam (2) with screws (A)
and tighten them with the allen key (F).
Item No.: K257003/K257008/K257010
6
Handset screw

F
4x4
2
4
Bx4
F
4x4
3
2
Bx4
F
4x4
B
Dx4
2
D
F
1
Dx8
F
4x4
Cx8
F
4x4
C
F
1
Type A: 2X700mm
Type B: 1X700mm，1X900mm
Type C: 2X900mm
STEP 2 Install the Lifting Columns
Insert the lifting columns(1) into the supporting beam. Tighten the screws
with the allen key (F).
STEP 3 Install the Feet
Choose feet according to needs
Assemble the feet(1) on the bottom of the lifting column(2) .
Use allen key(F) to tighten the screws (C).
STEP 4
STEP 5
STEP 6
Install the tabletop Loosen
Stretch
Tighten
Install the Handset
Port for
handset
Power port
Port for cable
connected to the
lifting column
Install the Cable
Management Cover
Method 1
,
Method 2
The installation method of the cable management
cover (3) is the same as that of method 1 in step 6.
When the supporting beam stretches to over 180cm,
cable management cover (3) needs to be placed on the
middle connecting rod.
The supporting beam must not
be extended beyond this hole.
First, screw the screw (B) into the supporting beam (2) with the allen key (F),
and do not completely tighten it, snap the cable management cover (3) into the
screw (B) on one side, and buckle the other side into the screw (B), Finally
tighten the screw (B) with the allen key (F).
Step 1: Do not tighten screws completely.
Step 2: Install the cable tray.
Adjust the distance of the
supporting beam according
to the actual situation.
Note: When the supporting beam stretches to
over 180cm, follow the installation Method 2 in
STEP 6.
Supporting beam scale mark
The scale mark on the
supporting beam
matches the dimension
of tabletop.

Common Error treatment
The following tips will help you detected and eliminate the common
fault and error. If the error you meet is not on the list, please contact
our customer service.
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
Error Method
No response while pressing
The desktop moving towards
the opposite direction as ordered
Rising in a low speed
The desk moving downwards
without any operation
Automatically Self-Reset
Overload Operation
Can’t reach the min or max height
Check if all the cables well connected;
Reposition;
Check if overloaded the max loading;
Check if overloaded the max loading;
Check if overloaded the max loading;
Restart after suspend for 18mins while
connecting with power;
Press "M"and "3" together for 3 seconds or
more, after hearing beep for twice, it will
reset.