ERGONOMIC SOLUTIONS FlexCharge4-DSK-V2 User manual

Model FCH4-DSK
INSTALLATION AND USE
FlexCharge4-DSK-V2
FCH4-DSK Rev C 11/17

1
FLEXCHARGE4-DSK SAFETY INSTRUCTIONS
Safety Instructions
Always read the safety instructions carefully.
• Do not install near heat sources such as radiators, heat registers
 stoves,orotherequipment(includingampliers)thatproduceheat.
• Unplug the unit during lightning storms or when unused for extended
periods of time.
• Toreducetheriskofreorelectricshock,donotexposethisunitto
rain or moisture, including any drips or splashes.
• Objectslledwithliquidssuchasvases,shouldneverbeplacedonor
near the unit.
• Do not open due to risk of electric shock hazard.
• The outlet used to power the unit should be easily accessible and
located near the equipment.
• The unit is for indoor use only.
• Please refer to the marking label on the unit for input and output
ratings. Do not overload the power supply.
• DO NOT USE this product in life support applications where failure of
this unit can reasonably be expected to cause the failure of the life
 supportequipmentortosignicantlyaffectitssafetyoreffectivenessis
not recommended. Do not use this equipment in the presence of a
 ammableanestheticmixturewithair,oxygenornitrousoxide.
• Failure to adhere to these instructions effectively voids the warranty.

2
FLEXCHARGE4-DSK PARTS AND TOOLS
PLEASE REVIEW these instructions before beginning the installation. Check
that all parts and tools needed were provided with your order. Contact your
supplier if any parts are missing. Do not discard the packaging until content
that the product operates to your satisfaction.
PARTS AND TOOLS PROVIDED
Power Module (1)
Power Outlets
USB Charging
Ports
Bottom Bracket (1)
M4 Allen Key (1) #6-32x¼ Flathead Screw (4) M3x12 Panhead Screw (2)
CAUTION:
Hand-tighten screws only.
ADDITIONAL TOOLS REQUIRED
• Phillips screwdriver
• Power drill with 1 /8"drillbit(under-deskmountsonly)

3
DESK CLAMP FLEXCHARGE4-DSK
There are three ways to mount the FlexCharge4 power module:
 •EdgeMount(page3)
 •GrommetMount(page5)
 •Under-DeskMount(page7)
Choose the best mounting method based on user preference and the
mounting circumstances.
Desk Clamp
With the edge mount method, the product is
clamped to the edge of the work surface.
Assemble the Brackets and Clamp
• Route the power cord through the
opening in the top bracket.
• Attach the top bracket to the
rear of the power module
using the two M3x12
panhead screws.
Tighten securely.
Power
Module
M3x12

4
FLEXCHARGE4-DSK EDGE MOUNT
Attach Bracket/Clamp Assembly to Power Module
• Position the assembly in the desired location and
clamp securely to the work surface by tightening
the triangle knob.
• Plug the power cord into an AC outlet
YOU ARE NOW READY to use the two AC power outlets and two USB charging
ports on the FlexCharge4.
Desk Clamp
The grommet mount method is similar to the edge
mount method, except here the assembly is
clamped to the edge of a 2¼” grommet hole
rather than the edge of the work surface.
Work Surface

5
GROMMET MOUNT FLEXCHARGE4-DSK
Remove the Desk Clamp
•Loosenthe(2)M5x8socketcapscrewsusingtheM4Allenkey.
— Desk clamp can be removed.
Attach Bracket Assembly to Power Module
• Route the power cord through the opening in the top
bracket.
• Attach the top bracket to the rear of the power module
using the two M3x12 panhead screws. Tighten securely.
Power
Module
M3x12
2”

6
FLEXCHARGE4-DSK GROMMET MOUNT
Clamp Power Module Assembly to Work Surface
• Retighten the two M5x8 screws to the bottom bracket, leaving about 1 /8"
exposed between the screw heads and the bracket.
—Withworksurfacethicknessesbetween⅞"and2",attachthescrewsto
the bottom two holes. Attach the clamp to the top two holes if the work
surface thickness is less than 1.5".
• Insert the bottom bracket through the grommet hole.
• Attach the clamp to the bottom bracket.
— Fit the keyhole openings in the clamp over the M5x8 screw heads. Tighten
the screws securely over the narrow portion of the keyholes using the
M4 Allen key.
• Clamp the assembly securely to
the work surface by tightening the
triangle knob.
• Plug the power cord into an AC
outlet.
YOU ARE NOW READY to use the two AC power outlets and two USB charging
ports on the FlexCharge4.
1
/8"
Exposed
M5x8
Hook Clamp Keyholes
onto Screws and Tighten
Minimum hole
diameter = 2¼”
Work Surface Grommet
Hole
Tighten Knob

7
DESK CLAMP FLEXCHARGE4-DSK
Under-Desk Mount
With this method, the top bracket is turned upside-
down so that it can be mounted to the underside of
the worksurface with M4x14 wood screws. As with the
other methods, the power module is mounted to the
bracket using two M3x12 panhead screws.
Drill Pilot Holes
• Use the top bracket as a template to mark where to drill four pilot
holes.
• Drill 1 /2" deep pilot holes using a 1 /8" drill bit.
CAUTION: Be careful not to not drill through the top of the worksurface.
Remove the Desk Clamp
• Loosen the M5x8 socket cap screws using the M4 Allen key.
•Removethebottombracketbylooseningthe#6-32x1/4”atheadscrews
using a Phillips screw driver
Attach Bracket to Underside of Work Surface
• Route the power cord through the opening in the top bracket.
• Attach the bracket in the desired location (typically at the front of the work
surfaceontheleftorrightside)usingthefourM4x14woodscrews.Tighten
securely.
Attach Power Module to Bracket
• Route the power cord through the opening in the top bracket.
• Attach the power module to the bracket using the two M3x12 panhead
screws. Tighten securely.
YOU ARE NOW READY to use the two AC power outlets and two USB charging
Top Bracket Power
Module
M3x12
M4x14
Top
Bracket
Bottom
Bracket
#6-32x¼
M5x8
Clamp

800.833.3746esiergo.com
©2017ESIErgonomicSolutions.Allrightsreserved. FLEXCHARGE4-DSK-V2 RevC 11/17
Additional Features
• Built-in surge protection
• Rotation AC outlet orientation designed to accomodate large plugs
• Complies with UL 962A Standard for Furniture Power Distribution Units and
meets respective spill test criteria.
• 3.1A USB charging module
can charge one tablet and
one smart phone at the same
time.