Euresys Coaxlink 1629 User manual

Coaxlink
Coaxlink Hardware Manual (PCIe/104 bus type)
1629 Coaxlink Duo PCIe/104-EMB
1634 Coaxlink Duo PCIe/104-MIL
3300 HD26F I/O module for Coaxlink Duo PCIe/104
3301 Thermal drain (Model 1) for Coaxlink Duo PCIe/104
3302 DIN1.0/2.3 Coaxial cable for Coaxlink Duo PCIe/104
HARDWARE MANUAL
© EURESYS s.a. 2020 - Document D206ET-Coaxlink PCIe104 Hardware Manual-eGrabber-14.0.1.2121built on 2020-11-05

2
This documentation is provided with Coaxlink 14.0.1 (doc build 2121).
www.euresys.com
Coaxlink Hardware Manual

3
Contents
1. About This Document 4
1.1. Document Scope 5
2. Mechanical Specification 6
2.1. Board and Bracket Layouts 7
2.2. Connectors 9
3302 DIN 2 CoaXPress Host Connector 10
CoaXPress Host A Connector 11
CoaXPress Host B Connector 12
3300 I/O Connector 13
C2C-Link Connector 15
Camera Power Input Connector 16
2.3. LEDs 17
CoaXPress LED lamps 18
12 V LED 21
Board Status LED 22
FPGA Status LED 23
2.4. Firmware Recovery Switch 24
2.5. Physical Characteristics 25
2.6. PCIe/104 Stacking Rules 26
3. Electrical Specification 28
3.1. Camera Interfaces 29
3.2. PCI Express Interface 32
3.3. Power Distribution Schemes 33
3.4. PCI Express Power 38
3.5. Camera Power Input 39
3.6. I/O Power Output 40
3.7. Differential Input 41
3.8. TTL Input/Output (Version 1) 43
3.9. TTL, 5 V CMOS and LVTTL Levels 46
3.10. Isolated Input 47
3.11. Isolated Output 49
4. Environmental Specification 51
4.1. Environmental Conditions 52
4.2. Temperature Monitor 53
4.3. Thermal Data 55
4.4. Compliances 56
5. Related Products & Accessories 60
5.1. 3300/3302 Accessories for Coaxlink Duo PCIe/104 61
5.2. Custom C2C-Link Ribbon Cable Assembly 63
6. Appendix 64
6.1. Connecting TTL Devices to Isolated I/O Ports 65
TTL And LVTTL Voltage Levels 66
Connecting TTL Devices to Isolated Input Ports 68
Connecting TTL Devices to Isolated Output Ports 70
Using External Power 70
Using Local 12 V Power 73
Coaxlink Hardware Manual

4
1. About This Document
1.1. Document Scope 5
Coaxlink Hardware Manual

5
1.1. Document Scope
NOTE
This document describes the hardware specifications of the following
eGrabber products and their related accessories.
Coaxlink main products
Product S/N Prefix Icon
1629 Coaxlink Duo PCIe/104-EMB KDI
1634 Coaxlink Duo PCIe/104-MIL KDR
□The S/N prefix is a 3-letter string at the beginning of the card serial number.
□Icons are used in this document for tagging titles of card-specific content.
Related accessory products
Product S/N Prefix Icon
3300 HD26F I/O module for Coaxlink Duo PCIe/104 KDM
3301 Thermal drain (Model 1) for Coaxlink Duo PCIe/104
3302 DIN1.0/2.3 Coaxial cable for Coaxlink Duo PCIe/104
□The S/N prefix is a 3-letter string at the beginning of the card serial number.
□Icons are used in this document for tagging titles of card-specific content.
NOTE
The S/N prefix is a 3-letter string at the beginning of the card serial number.
NOTE
Icons are used in this document for tagging titles of card-specific content.
Coaxlink Hardware Manual

6
2. Mechanical Specification
Mechanical specifications of the product(s) including: product pictures, physical dimensions,
connectors description and pin assignments, LEDs description, switches description, etc.
2.1. Board and Bracket Layouts 7
2.2. Connectors 9
2.3. LEDs 17
2.4. Firmware Recovery Switch 24
2.5. Physical Characteristics 25
2.6. PCIe/104 Stacking Rules 26
Coaxlink Hardware Manual

7
2.1. Board and Bracket Layouts
Coaxlink Hardware Manual

8
1629 Coaxlink Duo PCIe/104-EMB and 1634 Coaxlink Duo PCIe/104-MIL
●" CoaXPress Host A Connector" on page11
●" CoaXPress Host B Connector" on page12
●" C2C-Link Connector" on page15
●"12 V LED " on page21
●"Board Status LED" on page22
●"FPGA Status LED" on page23
●"Firmware Recovery Switch" on page24
Coaxlink Hardware Manual

9
2.2. Connectors
Coaxlink Hardware Manual

10
3302 DIN 2 CoaXPress Host Connector
Applies to:
Connector description
Property Value
Name CoaXPress Host
Type 2 x DIN 1.0/2.3 75 Ohms coaxial receptacles
Location Module-to-chassis coaxial cables
Usage CoaXPress Host Interface
Pin assignments
Pin Signal Usage
Inner1 CXP_A CoaXPress Host Connection A
Outer1 GND Ground
Inner2 CXP_B CoaXPress Host Connection B
Outer2 GND Ground
Coaxlink Hardware Manual

11
CoaXPress Host A Connector
Applies to:
Connector description
Property Value
Name CoaXPress Host A
Type MCX 75 Ohms coaxial female receptacle
Location Printed circuit board
Usage CoaXPress Host Interface
Pin assignments
Pin Signal Usage
Inner CXP_A CoaXPress Host Connection A
Outer GND Ground
Coaxlink Hardware Manual

12
CoaXPress Host B Connector
Applies to:
Connector description
Property Value
Name CoaXPress Host B
Type MCX 75 Ohms coaxial female receptacle
Location Printed circuit board
Usage CoaXPress Host Interface
Pin assignments
Pin Signal Usage
Inner CXP_B CoaXPress Host Connection B
Outer GND Ground
Coaxlink Hardware Manual

13
3300 I/O Connector
Applies to:
Connector description
Property Value
Name I/O
Type 26-pin 3-row high-density female sub-D connector
Location Remote I/O module
Usage General purpose I/O and power output
Pin assignments
Pin Signal Usage
1 GND Ground
2 DIN12+ High-speed differential input #12 – Positive pole
3 IIN11+ Isolated input #11 – Positive pole
4 IIN13- Isolated input #13 – Negative pole
5 IIN14- Isolated input #14 – Negative pole
6 IOUT12- Isolated contact output #12 – Negative pole
7 GND Ground
8 Not connected
9 GND Ground
10 GND Ground
11 DIN12- High-speed differential input #12 – Negative pole
12 IIN11- Isolated input #11 – Negative pole
13 IIN12+ Isolated input #12 – Positive pole
14 IIN13+ Isolated input #13 – Positive pole
15 IIN14+ Isolated input #14 – Positive pole
Coaxlink Hardware Manual

14
Pin Signal Usage
16 IOUT12+ Isolated contact output #12 – Positive pole
17 TTLIO12 TTL input/output #12
18 GND Ground
19 DIN11- High-speed differential input #11 – Negative pole
20 DIN11+ High-speed differential input #11 – Positive pole
21 IIN12- Isolated input #12 – Negative pole
22 IOUT11- Isolated contact output #11 – Negative pole
23 IOUT11+ Isolated contact output #11 – Positive pole
24 GND Ground
25 TTLIO11 TTL input/output #11
26 +12V +12 V Power output
Coaxlink Hardware Manual

15
C2C-Link Connector
Applies to:
Connector description
Property Value
Name C2C-Link
Type 6-pin dual-row 0.1" pitch pin header with shrouding
Location Printed circuit board
Usage Card-to-card link
Pin assignments
Pin Signal Usage
1 GND Ground
2 CSync1 Card-to-card synchronization bus – Signal 1
3 GND Ground
4 CSync2 Card-to-card synchronization bus – Signal 2
5 GND Ground
6 CSync3 Card-to-card synchronization bus – Signal 3
Coaxlink Hardware Manual

16
Camera Power Input Connector
Applies to:
Connector description
Property Value
Name Camera Power Input
Type 4-pin 0.1-in Molex KK 7478 male connector
Location Printed circuit board
Usage DC power input for PoCXP
Pin assignments
Pin Signal Usage
1 GND Ground
2 +24V0 +24 VDC input
3 +24V0 +24 VDC input
4 GND Ground
Coaxlink Hardware Manual

17
2.3. LEDs
Coaxlink Hardware Manual

18
CoaXPress LED lamps
Each CoaXPress connection is associated with a LED lamp mounted on the bracket (for PCie
cards only).
LED lamps mode control
The LampMode feature of the Interface module defines the lamps operation mode:
●When set to Standard (default value), the lamps indicate the state of the CoaXPress Link
connection.
●When set to Dark, all lamps are turned off.
●When set to Error, all lamps are turned off unless error conditions are detected.
●When set to Custom, all lamps are controlled by LampCustomValue, a bitfield where each bit
is mapped onto a lamp with 1 for orange and 0 for off by the LampCustomLedA …
LampCustomLedH boolean features.
Coaxlink Hardware Manual

19
CoaXPress Host Indicator LED lamps states
States description
Symbol Indication State
Off No power
Solid orange System booting
AlternateFlash_12_5 green
/ orange1Connection detection in progress; PoCXP active
Flash_12_5 orange2Connection detection in progress; PoCXP not in use
AlternateFlash_0_5 red /
green Device/ Host incompatible; PoCXP active
AlternateFlash_0_5 red /
orange Device/ Host incompatible; PoCXP not in use
Solid red PoCXP over-current
Solid green Device / Host connected, but no data being
transferred
Flash_1 orange Device / Host connected, waiting for event (e.g.
trigger, exposure pulse)
Flash_12_5 green Device / Host connected, data being transferred
500 ms red pulse3Error during data transfer (e.g. CRC error, single bit
error detected)
AlternateFlash_0_5 green /
orange Connection test packets being sent
Flash_12_5 red System error (e.g. internal error)
1Shown for a minimum of 1 second even if the connection detection is faster
2Shown for a minimum of 1 second even if the connection detection is faster
3In case of multiple errors, there shall be at least two green Flash_12_5 pulses before the next
error is indicated
Coaxlink Hardware Manual

20
Flashing states timing definitions
Indication Frequency Duty Cycle
Flash_12_5 12.5 Hz 25% (20 milliseconds on, 60 milliseconds off)
Flash_1 1 Hz 20% (200 milliseconds on, 800 milliseconds off)
Flash_0_5 0.5 Hz 50% (1 second on, 1 second off)
AlternateFlash_12_5 12.5 Hz 25% (20 milliseconds on color 1, 60 milliseconds off, 20
milliseconds on color 2, 60 milliseconds off)
AlternateFlash_0_5 0.5 Hz 50% (1 second on color 1, 1 second off, 1 second on
color 2, 1 second off)
Coaxlink Hardware Manual